Search Documents

By C. Feng, W. E. Krul

A study was made of the development of texture and the anisotropy in plastic flow of Ti-8Al-1Mo-1V alloy. Based on Pole figure determinations, the shifting of texture induced by rolling at approximately 400°C was found to be due primarily to slip rotation for the major Portion of the material. Grain boundary shear is believed to be an important factor. The anisotropy of the textured alloy was examined in terms of the variations of yield stress under tension and the ratio of bi -axial strain increments µp, in the temperature range 25" to 290°C. The results were related to Hill&apos;s theory on plastic anisotropy. The Schmid factors of (1100)[1120], (1101)[1120/, and (1101)[1120] slip systems were analyzed and found to be compatible with the observed anisotropy. Cross-slip between these planes was proposed as a possible deformation mode. In a number of published articles, considerable interest has been directed to the possible achievement of texture hardening in hcp metals. Following Backofen, Hosford, and Burke,&apos; this phenomenon was related to the yield criteria of the material and was expressed in terms of the biaxial strain ratio, r = d?w/d?l. The higher the value of r, the greater is the expected potential for texture hardening under certain loading conditions. For a given material, r varies with direction. Such variation can be traced to the anisotropy in plastic flow and can be explained within the framework of the various modes of deformation. Hatch2 found that a high r value coincides with a texture whereby the (0001) pole is closely aligned with the surface normal for sheet materials, Based on the analysis of the slip on the {1010}, {1011}, and (0001) planes, Lee and Backofen3 and Avery, Hosford, and Backofen4 concluded that the resistance to thinning is reduced by the operation of the (0001) <1120> slip system; with this reasoning they were able to explain the low r values (i.e., r « 1) observed in magnesium alloy sheets in the rolling direction and in commercially pure titanium in the transverse direction. The general equation, dealing with plastic flow in a polycrystalline aggregate has been used to correlate the plastic anisotropy and texture. In this expression, T and s are shear and normal stresses, and dri and d? are shear and normal strain increments, respectively. Assuming that five slip systems are operative within each grain and applying the principle of maximum work,5,6 one can determine the m value among the available systems. On this basis, Hosford7 and Chin, Nesbitt, and Williams&apos; were able to correlate m with yield stress under plane-strain compression, and Svensson9 was able to predict the variation of yield stress in textured aluminum. These workers made their analyses from materials in which slip operation is known to be associated with plastic flow. Questions remain regarding the derivation of Hill&apos;s theory on plastic anisotropy,10,11 since it was formulated on von Mises&apos; yield criterion.&apos;&apos; Its ability to deal with other forms of deformation has been in doubt.13 Others have discussed the validity of Hill&apos;s quadratic equation relating strain and yield stress.14&apos;15 For hcp titanium, deformation by various modes of slip and twinning operations has been reported.16-20 If all possible modes of deformation operate and contribute substantially to the plastic flow, it is difficult to imagine how the quadratic expression can suitably describe the anisotropic plastic flow of titanium alloys. Backofen and Hosford15 considered that Hill&apos;s is a macroscopic theory and implied that the major mode of deformation by slip mechanism will adequately describe anisotropy of the material. In the present investigation, slip operation will be shown to play the major role in the development of sheet texture induced by rolling of a commercial titanium alloy. Although twinning and other modes of deformation may also operate, their operation is believed to be secondary. The anisotropic properties of the sheet, which can be expressed in terms of directional variation of r, µp = -d?w/d?l and the yield stress will be shown to be governed primarily by slip operation. MATERIALS AND EXPERIMENTAL TECHNIQUES The titanium alloy chosen for the present investigation had a nominal composition of 8 wt pct Al, 1 wt pct Mo, 1 wt pct V, and 0.1 wt pct interstitial impurities. Sheets varying between 0.1 and 0.15 in. thickness were used. The alloy was received in a condition which was prepared by rolling at 900°C and annealing at 700°C. Subsequently, the sheets were subjected to further reduction in thickness by rolling at 400°C. A total reduction in thickness of 65 to 70 pct was obtained by a series of quick passes in a rolling mill with intermediate reheating. Further reduction in thickness was not possible due to cracking developed at the edges of the sheets. X-ray measurements were conducted in a Siemens and a Norelco unit to determine the texture of the sheets. Reflection techniques were used exclusively with CuK, radiation and a nickel filter. The loss of X-ray intensity due to geometric defocusing was calibrated with a technique described previously." The (0001), (1010), and (1071) pole figures were plotted from 0 to 80 deg, and to present the texture elements quantitatively, inverse pole figures were constructed following the technique described by Jetter, McHargue, and Williams.22 Tensile experiments were carried out at 25", 175",

Jan 1, 1970

By T. A. Klinefelter, O&apos, R. G. Meara, Glenn C. Truesdell, Richard W. Smith

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for&apos; aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.&apos; With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By C. S. Lyons and. A. L. Johnson

A few years ago a leading American builder of centrifuges said, "No one uses a centrifuge if the job can be done any other way." This statement was essentially true at that time, not because the basic functional and economic principles involved did not frequently favor centrifugal methods, but rather because so many of the highly specialized features of the mechanical and functional peculiarities of continuous centrifuges had not been fully developed. The idea of using centrifuges in mineral dressing is definitely not new. There are literally hundreds of patents on centrifugal machines and processes for the mining industry. Many of them cover principles that are basic to the functioning of most centrifuges in operation today. In spite of this, until 1935, there were practically no successful applications of continuous centrifuges in the United States in the mineral industry, nor for that matter were there more than a mere handful of such machines in operation in North America in any industry. This was true despite the obvious desirability of machines that could furnish the advantages of high centrifugal settling forces in a continuous operation. The reasons for this are simple, even if not obvious: I. Finely divided solids, when thrown out of fluid suspension under high cen- trifugal forces, frequently exhibit physic a properties (particularly rheological or flow properties) that are markedly different from those they possess when settled out by gravity alone, and machines that are not designed in careful detail to cope with these peculiarities &apos;seldom function satisfactorily. 2. Most continuous centrifuges embody a solids-conveying element in the form of a very special screw conveyor. The rotation of this member under conditions of operation culls for drive designs that were not satisfactorily provided until the introduction of the Bird gear unit about 1934. These matters will be touched on later. Continuous centrifuges are now operating successfully in the mineral industry. Some units have singly handled more than 500,000 tons of solids during the past ten years. Generally their operation has been characterized by large unit capacities, complete elimination of labor, minimum supervision, moderate maintenance and power costs. Typical Centrifuge Applications Most materials classified by centrifuges are of subsieve particle size. Practically speaking, this means her than 100-mesh. A unit of measure other than screens is needed in order to consider these products properly. Such a unit is the micron, which is equal to one one-millionth of a meter; roughly1/25,000 of an inch. The opening in a standard 200-mesh screen is about 75 microns while a 325-mesh opening is roughly 43 microns.

Jan 1, 1948

By Charles A. Morgan

The proms of mire drawing depends upon the property which certain metals possess, termed ductility, which is defined in Brande&apos;s Dictionary of Science as a property inconhequcnce of which metals may be drawn out at length wilhotit interrupting the continuity of their constituent parts. As ticfincd thy M. Tresca, it is the property of flowing when subjected to pressure, and ie termed by him the "flow of solids," in his paper, read before the AcaiXemy of Sciences in Paris, November, 1866 * In the simple language of the wire shop, it is that quality in certain metals that thcm to be drawn (or etretched) out througl~ a tapering hole in a metal block or die, the die being more dense and harder than the metal to be redud. It is a fact well known to tllose slrillet1 in the ai*, that to eu~xeed in drawing iron or steel wire, it is of&apos; the utmost, importance to have tborough lubritatiun, as a lack of it woullii udu-se abrasion of the wire, or of the walls of the tapering hole in the dia or plate, and quickly put an end to the operation. In drawing coarse or large sizes of pire, say & inoh diameter, the pressure upon the sides of the tay~dng hole, where the wire comes i.u contact with the die, so great that an ordina,y labricaot is equeezed out when the nsoal rc~luctions iu size are matie, and abrasion takea place. In order to meet this diffic:ulty, and emure proper lubrication, it has been a ccmmon prtictice for yazrs to apply a paste made of rye or wheaten flour, or lime, to the surface of the wire to be drawn, and when the pnstc is dry, to smwr tl~e wire with tallow or grease; the wire is then ready to be draw, the dried pa serving fo prevent the lubricant from being presetf out in the prows. Some years since, when Bessemer metal came iargely into use material for wire, &apos;the writer fourid that its dmwing requid so much more power than iron wire, that he was led to institute a. series of trials to ascertain the difference in power required. It was fotind that Bessemer wire requircd from 100 to 200 per cent. more power to makc the same reduction in sizes than soft iron wire, the difference depending npou the amount of carbon and other chemical constitu-

Jan 1, 1881

By J. D. Lindner, Gene E. Roark

Waterflooding operations in the Langston-Kleiner field. Young County, Tex., are described. Widespread application of formation fracturing has been practiced in both producing and injection wells. Field performance data arc cited which indicate than no detrimental effect on sweep efficiencies and that probable benefits in imectivily have resulted from the fracture treatments. I N T R O D U C I O N This paper is a report on a waterflood operation which is being carried out in the Lanpston-Kleiner field located in Young County, Tex. The oil reservoir aflected by this flood operation occurs in a Strawn sand member at an approximate depth of 3.550 ft subsurl&apos;ace. The operators of&apos; the project are Kleiner Estate. Turncr. Fiske. and West who are hereinafter collectively referred to as the Operators. Although the operation is unusual in several respects, the distinctive feature of this flood has been the widespread application of hydraulic formation fracturing treatments as a means to improve productivity and injectivity of the wells. It shall he the purpose of this paper to present basic information regarding the reservoir characteristics. op- craling practices, and waterflood behavior so that conclusions may be drawn concerning the effects which the fracture treatments have had on the performance of this water flood to datc. DEVELOP MENT Development of the 3,550 ft Strawn sand reservoir occurred during 1951 and 1952. The early development occurred on the Langston and Davis leases which arc in the northern region of the Operators&apos; holdings and the wells were drilled on 20-acre proration units according to the field rules. However, studies of the economics of this program. coupled with the decision to proceed with pressure maintenance by water injection. resulted in the adoption of wider spacing in the later stages of development. This variation in spacing is apparent upon inspection of Fig. I upon which only the 3,550-ft Strawn sand producing and injection wells have been located on the Operators&apos; properties. The development to the north of the operators leases is Ihe Garvey Strawn field and that to the south is the Taylor Strawn field. It wits determined that unitization of the leases to he involved in the waterflood program was not feasihle. Consequently. a system of offset injection wells, or lease line injection wells, was adopted from place to place as required to protect correlative rights in the program. This resulted in a dispersed array of injection and producing wells with relatively close proximity of wells along lease line areas and wider spacing toward

Jan 1, 1956

By T. A. Klinefelter, Glenn C. Truesdell, Richard W. Smith, R. G. Meara, O&apos

The investigation of domestic talcs was undertaken by the Bureau of Mines, Department of the Interior, in cooperation with the University of Alabama, at the request of the U. S. Army, on Dec. 1, 1941: "Considerable concern has been expressed by the Supply Arms and Service over maintaining continued availability of supplies of the necessary raw materials. These ceramic products are used by the Signal Corps in all army radio equipment, and to a greater degree in the new ultra-high-frequency equipment. The Air Corps has become a user of large amounts of radio-grade ceramics for&apos; aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio air-navigation aids of the Civil Aeronautics Board." History The use of steatite and talc in ceramic bodies goes back a great many years. If pure, talcs shrink little under heat-treatment and are very resistant to heat shock. The massive form, commonly called "steatite" by the trade, cuts and works easily, and this was naturally the first method used in obtaining articles of talc. When gas was in general use for illuminating purposes, a. large business was carried on in the manufacture of tips for gas burners.&apos; With the development of uses for electricity, low-tension insulators were made in a similar manner; and, in fact, the forming of shapes from massive talc continues. However, as the business increased, cuttings and waste became more and more of a problem. In the twenties, one of the larger producing firms had a cooperative agreement with the Bureau of Mines at its Columbus station to work out a body using the finely powdered material. Somewhat earlier, manufacturers of spark plugs used the finely ground talc as part of the body and to some extent in wall-tile bodies. Somewhat later it came into use for kiln furniture and similar products and still more recently it has been used in some dinnerwares. With the development of the radio and the high-frequency fields generated, it was found that a dense steatite porcelain was far better than even high-tension electrical porcelain, which is a clay-flint-feldspathic type of body. Until the war increased the demand, the several pioneer steatite-porcelain manufacturers were able to furnish adequate supplies. When war began in Europe and Asia, three important foreign sources of raw material were cut off; i.e., the French, Italian, and Man-churian talcs. Domestic producers of high-grade porcelain are few, and the trade

Jan 1, 1948

By C. S. Lyons and. A. L. Johnson

A few years ago a leading American builder of centrifuges said, "No one uses a centrifuge if the job can be done any other way." This statement was essentially true at that time, not because the basic functional and economic principles involved did not frequently favor centrifugal methods, but rather because so many of the highly specialized features of the mechanical and functional peculiarities of continuous centrifuges had not been fully developed. The idea of using centrifuges in mineral dressing is definitely not new. There are literally hundreds of patents on centrifugal machines and processes for the mining industry. Many of them cover principles that are basic to the functioning of most centrifuges in operation today. In spite of this, until 1935, there were practically no successful applications of continuous centrifuges in the United States in the mineral industry, nor for that matter were there more than a mere handful of such machines in operation in North America in any industry. This was true despite the obvious desirability of machines that could furnish the advantages of high centrifugal settling forces in a continuous operation. The reasons for this are simple, even if not obvious: I. Finely divided solids, when thrown out of fluid suspension under high cen- trifugal forces, frequently exhibit physic a properties (particularly rheological or flow properties) that are markedly different from those they possess when settled out by gravity alone, and machines that are not designed in careful detail to cope with these peculiarities &apos;seldom function satisfactorily. 2. Most continuous centrifuges embody a solids-conveying element in the form of a very special screw conveyor. The rotation of this member under conditions of operation culls for drive designs that were not satisfactorily provided until the introduction of the Bird gear unit about 1934. These matters will be touched on later. Continuous centrifuges are now operating successfully in the mineral industry. Some units have singly handled more than 500,000 tons of solids during the past ten years. Generally their operation has been characterized by large unit capacities, complete elimination of labor, minimum supervision, moderate maintenance and power costs. Typical Centrifuge Applications Most materials classified by centrifuges are of subsieve particle size. Practically speaking, this means her than 100-mesh. A unit of measure other than screens is needed in order to consider these products properly. Such a unit is the micron, which is equal to one one-millionth of a meter; roughly1/25,000 of an inch. The opening in a standard 200-mesh screen is about 75 microns while a 325-mesh opening is roughly 43 microns.

Jan 1, 1948

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By R. F. Mehl, B. Lustman

The formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.&apos; It is necessary here only to cnumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type—i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained—the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [i] where X is the thickness of the alloy layer, k thc reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.$ In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varics with temperature according to the Arrhenius equation: k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. Ali phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By F. W. Jessen, N. Lamont

The effect of an existing fracture or joint plane, which may exist in a rock, on the extension of a hydraulically induced fracture through the rock has been investigated in the laboratory. By use of a series of models made from various outcrop rocks, the width and orientation of existing fractures do not alter the extension or direction of the hydraulic fracture. The results, which conform quite well with the Grifith theory of failure, are illustrated by a series of photographs of the various models. INTRODUCTION The process of hydraulic fracturing has been widely used in the oil industry since its introduction in 1948 and has made possible the production of many reservoirs which would have been uneconomical prior to this process. Numerous studies of the mechanics of the process2-h nd of the effects of oriented fractures on recovery&apos;.&apos; have appeared in the literature. The increased recoveries led to attempts to predict the orientation of hydraulic fractures at the wellbore and to the development of methods to control this orientation. Field tests have been devised"." which indicate the validity of theoretical predictions of fracture orientation at the borehole. The direction of extension of hydraulic fractures from the borehole has not received much attention since most studies have predicted, at least implicitly, that a fracture will continue in the same plane unless a change of state of stress in the rock occurs. Since such predictions are based on the assumption of rock homogeneity, the effects of rock heterogeneities are left unknown. Most sedimentary rocks are composed of layers which reflect the changing depositional conditions of geological time. In addition, the more competent rocks frequently are fractured and jointed as the result of structural deformations or tectonic movements. Evidence of such joint systems exists in many surface outcrops, and it can be assumed that similar systems occur in many subsurface rocks, although the individual joints may be rather tightly closed due to overburden forces. This paper investigates the effect that an existing fracture in a rock would have on the direction or orientation of an extending or advancing hydraulic fracture when it intersects the existing fracture. The study was conducted on small rock models under triaxial stress conditions. The results indicate that an existing fracture will have little effect on the hydraulic fracture. THE MODEL STUDY The rock model represents an elemental portion of the earth containing an existing fracture which is located at some distance from a borehole from which hydraulic fracture is being extended. A generalized view of a model is presented in Fig. 1. The models were constructed from cement blocks and natural rocks. The various materials tested and some of the physical properties are listed in Table 1. The rocks were cut into rectangular blocks with dimensions of 11/2 X3Y2 X4 to 8 in. An initial slot was cut into the end face of each block along the longitudinal axis normal to the top face. The slot was filled with plastic aluminum along its outer edge to a depth of 1/16 in. A hole of 3/8-in. diameter was drilled into the sealed slot at the center of the end face to serve as an entry port for the fracturing fluid. Existing fractures of various types were simulated in the models. A "hairline" fracture with essentially zero width was created by cutting the model into two parts with a diamond saw and replacing the two parts together along the cut. A finite-width fracture was created by placing a layer of sand grains between the two faces of the cut just described (see Fig. 12). A large open fracture (similar, perhaps, to a vug) was created by cutting the model in two parts and removing a portion of the downstream block to a depth of % in. See Fig. 13. For a fourth

By Harry H. Power

The relative merits of air and natural gas as propulsive agents in pressure drive operations have been discussed for a number of years. When air or gas is introduced into the sand, various factors lead the operator to the selection of what he believes to be the proper propelling medium; but when the question of relative drive effect is raised, several physical and chemical premises must be taken into consideration in arriving at a conclusion as to the superiority of one medium over the other. Dow and Calkins1 and Beecher and Parkhurst2 have contributed fundamental experimental work on the effect of dissolved gas in lowering the viscosity and surface tension of crude oil. Herold; and Tickell&apos; have indicated that whatever type of reservoir control obtains, gas plays other important parts in the movement of oil towards the well, namely: 1. The propulsive and expansive force of the gas. 2. The "Jamin effect," or resistance to the movement of oil in a porous media due to the formation of gas bubbles. When quantitative studies are made, parallel conditions must be selected whereby we may say definitely whether air is superior to gas as a driving medium, or vice versa. Examples of similar conditions are not easy to find in the field. However, in the laboratory we can make determinations which may lead to general conclusions when applied to the field. The experimental and research work described here was started at the laboratories of the University of California in January, 1927, and completed in private laboratories at Tulsa, Okla., in February, 1928. The apparatus used was designed especially for the work.

Jan 1, 1929

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.&apos; The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. &apos;H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. &apos;E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 &apos;C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

Discussion of the paper of GEORGE S. RICE and H. H. CLARK, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2563 to 2571. NORMAN V. BRETH,* Pittsburgh, Pa.-It was my privilege to visit in the last two months on behalf of the U. S. Bureau of Mines 10 mines where electric shot-firing systems controlled from outside the mine are installed. I will describe briefly what I saw in some of these mines, which are located in Utah, New. Mexico, Oklahoma, Alabama, and Kansas. At a mine in Utah, 230-volt alternating current is used to fire the shots, which is taken from a small transformer in the substation. The shot-iring circuit is independent of all other wires and is tested for grounds every day. There are no lightning arresters on the firing circuit. Porcelain insulators are used inside of the mine, and glass outside. The switches are situated as follows: One in the substation, one in, the shot-firer&apos;s cabin, two at each cross entry; where the shot-firing circuit crosses the trolley wire a switch is placed on either side of the entry in series with the shot-firing circuit. The miners are checked in and out of the mine. The coal is undercut and is shot down with permissible explosive, the shots being connected in multiple. There are 75 to 110 shots fired each day. A great many times there are no missed shots. If not more than two or three are missed they are left until next day. The fan is kept running at full speed when the shots are fired. The shot-firing switch is closed only once and the whole mine is shot at once. At another mine in Utah, power wires are used for shot-firing circuits; 500-volt, direct current is used to fire the shots. The only sizes of wire used outside of the power wires are Nos. 8 and 14 B. & S. gauge. The return is connected to the pipe lines and track. Porcelain insulators are. used inside of the mine.

Jan 4, 1915

By S. F. Shaw

The principles involved in lifting oil in wells flowing naturally are identical with those underlying the flowing of wells by means of the air-gas lift, and information of a dependable nature obtained in the study of the air-lift can be applied to wells with natural flow. A well flowing naturally is one in which the lifting is done by means of the gas-lift, for which the gas is supplied entirely by the formation from which the oil is derived. In air-gas lift operations, there is insufficient gas supplied by the formation to lift the oil to the surface in an efficient manner, therefore additional gas for this purpose must be furnished from an outside source. There may, at times, be conditions obtaining in natural flowing wells different from those in wells flowed by gas-lift, but these differences do not at all conflict with the main principles of gas-lift work. One such condition is met with in wells in which the gas supplied by the formation is in considerable excess of that required to lift the oil to surface; this excess may be so great as to reduce the quantity of oil that can be lifted through the particular diameter of casing or tubing that has been lowered into the well. This same condition can be brought about, however, by supplying a large excess of gas from an outside source to an artificial gas-lift well, and a study of the effects obtained from injecting a large excess into the well can be applied directly to handling wells flowing naturally which have a large excess of gas supplied by the underground reservoir. Conditions for Lifting Oil The main factors to be considered in flowing wells are as follows: 1. Submergence, or pressure at the bottom of the tubing or casing. 2. Lift; the height to which the liquid must be raised. 3. Diameter of the flow tubing or casing. 4. Quantity of liquid to be lifted. 5. Pressure at the discharge end of the flow tubing, or back-pressure, as it is sometimes called.

Jan 1, 1930

By Joseph Jensen

California&apos;s outstanding contribution to unit operation is the plan of development now established for the North dome of the Kettleman Hills. Beginning April 1, 1931, the Kettleman North Dome Assn. will control the unified operation and development of 10,800 acres of proven and semiproven oil land, and at the same time the Standard Oil CO. of California will operate as another unit its fee land of 9460 acres of similar character. The holdings of the two companies are in a checkerboard mile-square pattern. In addition to this, 410 acres of land may yet be included in the Kettleman North Dome Assn. unit and 530 acres of land are definitely out of both units. The owners of some of this land have expressed their intention of cooperating in a reasonable way with these two units. Cooperative agreements are now in force as to most of this field. Under the definitions of a unit pool and a near-unit pool,&apos; the operation at Kettleman Hills will be a near-unit operation, but because of the size of the structure and its proven highly productive character, the arrangement. concluded on Jan. 31, 1931, in the approval of the Kettleman North Dome Assn. Agreement by Secretary of the Interior Ray Lyman Wilbur and by California State Oil and Gas Supervisor R. D. Bush is of outstanding importance to the entire oil industry. No other major unit operation plans are under way in California at the present time. There has been some little discussion of a plan in the North Belridge field and a feeling that the discovery of oil in the Lost Hills field and also in the South Belridge field would necessitate consideration of unit plans. So few data are available for these areas, as to the land that should be included in such unit plans, that little constructive action is now possible. The beginning of drilling on the Middle dome of the Kettleman Hills also makes it an area deserving consideration for unit operation. All four of the above-named areas lie on the west side of the San Joaquin Valley, in Kings and Kern counties, to the south of the

Jan 1, 1931

By R. S. Hadi, L. Svarovsky

SUMMARY This is a report of a new development in on-line particle size measurement of fine powders in dust-laden gases. A continuous sample of the solids-air suspension is drawn from the process stream via a sampling probe by means of an air operated ejector into a cyclonic separator whereby the sample is subjected to a particle size dependent separation process and split into two streams, "overflow" and "underflow". The overflow stream carries most of the fines at a relatively low concentration and the underflow stream carries the coarse particles at a relatively higher concentration. The concentration of solids in the two streams is detected by electrostatic noise level technique which utilises the electrostatic charge accumulated on the solid particles due to their high velocity in the turbulent air stream, for the mass concentration measurement. The ratio of the solids concentration of the fines stream to that of the coarse stream is then correlated against the average particle size in the main process stream by a calibration curve. The in-plant tests clearly indicate that this relatively simple instrument offers good sensitivity in the size range from 2 to 6 µm, and is capable of giving a continuous indication of average particle size for process control purposes. Although the instrument was developed for a particular application, it may be used in other situations where fine powders are conveyed in gas streams. British and foreign patents are applied for.

Jan 1, 1980

By David L. Holt, Walter A. Backofen, Anwar-uI Karim

Specimens of a hydrided Mg-0.5 Zr alloy were strained in tension at 500°C and constant rates of 2 x10-3 5 x 10-3, and 2 X 10" min-1. Hydride-denuded zones formed at grain boundaries normal to the tensile-stress direction as a result of magnesium transport during difusional flow. The width of the zones could be measured and the measurement used for calculating the diffusional component of the imposed tensile strain. The strain from diffusional flow was found to increase with imposed strain at a diminishing rate, tending to saturate at approximately 12 pct. Strain rate sensitivity of flow stress was low. The apparent non Newtonian character of the diffusional flow is attributed to a non Newtonian process acting in parallel with it which could be boundary shear. Fracture grows out of voids that form in the denuded zones. DEFORMATION of a grain by diffusion of atoms from boundaries stressed in compression to boundaries stressed in tension is Newtonian viscous,1-3 and evidence has accumulated in recent years that such a process may be responsible for the high strain-rate sensitivity of the flow stress of super-plastic alloys.4"7 One piece of evidence is that experimental stress: strain-rate relationships can be quantitatively explained.5-7 There is also metallo-graphic evidence of diffusional flow in superplas-ticity, but in a limited amount. The formation of striated bands on the surface of superplastically deformed specimens has been attributed to diffusional flow.5"7 The basis of that attribution came from experiments on a coarse-grained, nonsuperplastic and hydrided Mg-½ wt pct Zr alloy which formed hydride-denuded, light etching zones at tension-stressed boundaries when strained in tension at 270?C.6 The origin of these zones had already been traced to the diffusional flow of magnesium atoms to the boundaries.&apos; The particular observations in the more recent work were of striated-band formation on the surface and denuded-zone formation internally, with both the bands and zones having the same width and appearing at tension-stressed boundaries. It was argued that the bands were a surface manifestation of the zones and hence of diffusional flow. Of course in superplastic alloys which do not contain internal metallographic "markers", the surface bands can be the only metallographic indication. In the present work, denuded-zone formation was utilized, as it has been by others,9-11 to extend the observations of diffusional flow and to measure the strain, ed, resulting from it. Grain size had to be large to measure ed with accuracy. The grain size chosen for this study was -30 , and with that a strain of 10 pct from diffusional flow produces a denuded zone only 3 µ in width. The large grain size naturally precludes superplasticity. The observations of diffusional flow were complemented by determining the strain from the other operative deformation modes: slip, e,, and grain boundary shear, egb. An incremental specimen extension is the sum of increments from slip, and grain boundary shear as well as diffusional flow. Division by a common length is required to convert to strain. If this length is taken as the initial specimen length, then imposed engineering strain, e, is given in terms of the component engineering strains by e = ed + es + egb [1] Stress:strain-rate relationships are determined by the way in which this "strain balance" is made up. EXPERIMENTAL Material. Zirconium hydride markers were introduced into the Mg-0.5Zr alloy by annealing in hydrogen at 450°C for 30 min. The hydride concentration was particularly high at zirconium rich stringers, which was fortunate in that the transverse boundaries at which denuded zones form lie perpendicular to the stringers. Grain size after annealing was 30 µ. Photomicrographs of unstrained and strained material are shown in Fig. 1. Procedure. Specimens were strained in tension with an Instron machine at crosshead velocities of either 2 x 10"3, 5 x X or 1 x 10-2 in. min-&apos;. Specimen length and diameter were 1.0 and 0.2 in., respectively, so that initial strain rates in tests at constant crosshead speed were 2 x 10"3, 5 x X and 1 X l0-2 min-1. Tests were made at 500°C which is a compromise temperature at which diffusional flow is still measurable but grain growth is not active enough to interfere with metallographic measurements. The tests were made in a hydrogen atmosphere. Strain Balance. An equation additional to [I] is eg = ed + es [2] where eg is strain measured from grain elongation. Measurement was made of ed, eg, and, of course, e, which enabled all the strains in Eq. [I] to be determined. For this purpose, strained specimens were sectioned longitudinally, polished, and etched. The strain from diffusional flow, ed, was computed by measuring on photomicrographs the width in the tensile direction of denuded zones at either end of a grain XI, X2, adding them, and dividing by twice the initial longitudinal grain dimension L0, Fig. 2. Reported values are the results of measurements on seventy randomly selected grains; 95 pct confidence limits on ed were +1.5 pct strain. To measure eg, the maximum length, L, and the maximum width, W,

Jan 1, 1970

By R. H. Goodrich

Development in this district during the year 1929 was little different from that of any other year despite the somewhat depressed condition of the oil business in general. The year was marked by: (1) An intensive geophysical campaign in the search of deep-seated salt domes; (2) the rather successful exploration and development of lateral sand production on the flanks of some of the older domes. Geophysical Exploration Geophysical work is confined almost exclusively to the torsion balance and seismograph. At the beginning of the year there were approximately 185 individual instruments of all types engaged in the search of structures in the Gulf Coast of Texas and Louisiana. This total includes 3 magnetometers, 83 torsion balances and 100 seismographs. The number of parties operating the torsion balances was 47; seismographs, 20; magnetometers, 3. It is estimated that 4,800,000 lb. of dynamite or other explosives were used in seismic exploration. During the year the torsion balance and seismograph were credited with having discovered the following salt domes: Texas, Danbury dome, Brazoria County, H. & T. B. R. Co., and Clodine dome, Fort Bend County, John Fredricks and Wm. Stanley, Satowsky Survey; Louisiana, Iowa dome, Calcasieu and Jefferson Davis Parishes, T. 9 S., R. 6 and 7 W., and Cameron-Meadow dome, Cameron Parish, T. 14 S., R. 13 W. Because of the secrecy maintained in these developments, it is somewhat hazardous to venture opinion as to the number of salt domes found during one year. The discovery of gas at Mykawa district and at Genoa district, in Harris County, Texas, is considered of more than passing importance, because there is indication in the performance of these two districts that commercial accumulation of oil and gas may be found in the Gulf Coast on structures other than the wore or less definite salt dome type. While it is generally conceded that the accompanying structure in these instances are deeply buried salt domes, it is a fact that neither the seismograph nor the drill have indicated the presence of salt.

Jan 1, 1930