Search Documents

By M. B. Kasen

eralized strain equation appear quite different they are really identical. This identity can be shown in a simple mathematical rearrangement. Referring to Eq. [I], the substitution of ln(1 +?E) for ? (where ?E is the engineering strain) yields: a =s8- (s8?so)e?1/?c) ln(1 +s8??E) [4] or s =s8?(s8?so)(l +?E)-1 [5] Replacing (1 + cE) with its equivalent, (l/lo): s=s8?(s8?so)l/€c [6] Adding and subtracting the quantity (s8 - so) yields: s=s8?(s8?so)+ (s8-so) l-(^)l/£c [7] = s0+(s8?so)ri-(^0)1/^l [8] Letting n = 1/?c it follows that: This equation will be seen to be identical to the generalized strain expression in Eq. [3], the coefficients a and b being equal to so and (s8?so)/?c or n(s8?so), respectively. Confirmation of the relationship noted above was provided by fitting experimental stress-strain data5 for 304 stainless steel (total strain from 0.072 to 1.15) at room temperature at a true total strain rate of 4 x 10-3 sec-1 to Eqs. [I] and [3]. In this study nonlinear regression analyses were used to evaluate the equation constants. The results of this evaluation are presented in Table I. When these constants are used in Eqs. [I] and [3] the curves obtained are coincident. It will also be noted that the value of n is equal to YE,, the value of a is equal to so, and the value of b is equal to (s8 - so)/Ec. These equalities are illustrated in Table I where the Voce constants in parentheses were calculated from a, b, and n values. Excellent agreement is seen to exist. It is concluded, therefore, that the Voce equation is, indeed, identical to the linear expression involving generalized strain. In applying the generalized strain concept to stress-strain data, it has been noted3 that data within what was termed the transition region (first few points in the plastic flow region) must be excluded from the analysis in order to obtain the linearity in Eq. [3]. A similar exclusion applies in the use of the Voce equation since an expression which would describe the strain-hardening region would usually be found to be not too effective in the elastic-plastic fillet2 which connects the elastic line to the strain-hardening region. These considerations further substantiate that Eqs. [I] and [3] do indeed describe identical behavior. Note added in proof. Since this manuscript was submitted for publication, correspondence with Professor S. R. Davies, University of Edinburgh, (of Ref. 3) indicated that his associates have also confirmed the identity between the Voce equation and the generalized strain concept. It is sometimes desirable to obtain a small grain size in super-purity metals. Unfortunately, the absence of impurities, the low recrystallization temperatures, and the low activation energies for boundary motion result in rapid growth of relatively few grains when conventional recrystallization practices are used. For example, Arajs et al.1 were unable to obtain a mean grain diameter less than about 0.4 mm in iron containing 38 at. ppm of impurity. The <1 at. ppm purity range in many modern superpurity metals results in yet larger limiting grain sizes. It is the purpose of this communication to describe a technique by which mean grain diameters as small as 30 µ have been produced in aluminum having an impurity content < 0.5 at. ppm. The technique should be applicable to superpurity metals other than aluminum and has potential applications to grain refinement of commercial alloys. The necessary and sufficient requirements for production of a small grain size are as follows: a) a large number of potential nucleating sites must be created randomly within the cold worked material, b) sufficient thermal energy must be provided at a rate that will simultaneously activate a large fraction of the potential nuclei, and c) the grain growth must be stopped shortly after grain impingement.&apos; A high density of potential grain nuclei may be cre-

Jan 1, 1970

By E. O. Jones, E. Whitehead

During the heating of cold-worked nickel silver, the tendcncy of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. Changes in Alloys During Heating and Cooling During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting1 suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320" C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 1, 1926

By J. K. Edgar

For a number of years the production and use of super-purity aluminum (better than 99.99 pct) has been steadily increasing. High-grade lots of. such aluminum show certain outstanding characteristics not found in lower grades containing principally silicon, iron and copper as impurities. One such characteristic is the so-called "self annealing," that is, the re-crystallization of the heavily cold worked metal at room temperature.&apos; Interest therefore is aroused as to the effects of the impurities. It is well known that the amounts of silicon and copper which occur in aluminum of better than 99.95 pct are completely soluble, at least at elevated temperatures (above 200°C). Iron, on the other hand, is known to be fairly insoluble in solid aluminum. Thus, a knowledge of the limits of this solubility would he of considerable use in studying the characteristics of the high purity metal. All investigators have agreed that iron has very low solubility in solid aluminum. Rosenhain, Archbutt and Hanson2 reported traces of an aluminum-iron phase in the "purest samples of aluminum obtainable." Gwyer and Phillips3 reported that an iron constituent was visible under the microscope in metal containing ".0088 per cent iron." Roth4 found that in the solid state the solubility of iron in high purity aluminum was 0.01, 0.01, 0.017 and 0.022 pct at 225, 320, 500 and 600°C respectively. Dix5 working with alloys containing less than 0.03 pct impurities, concluded from microscopic and chemical analyses of eutectic areas that the eutectic composition was close to 1.7 pct iron. Dix placed the eutectic temperature at 65s°C. Archer and Fink,6 using high purity aluminum-iron alloys, found that the hypoeutectic liquidus intersects the eutec-tic horizontal at 1.7 pct. This is in fair agreement with the investigation of the aluminum-iron system by Gwyer and Phillips who placed the eutectic at 1.89 pct iron with a freezing point of 653&apos;C. Preparation and Chemical Analysis oP Alloys Electrolytically refined aluminum (99.991 pct aluminum) and a high purity alumi-num-iron alloy (11.45 Pet iron) were used in the preparation of the alloys for this investigation. To aid in controlling the iron content of the experimental alloys, an alloy of lower iron content was prepared first from these materials. The high purity aluminum was melted and heated to about 700°C in a plumbago crucible coated with alundum cement and the aluminum-iron alloy was then added. The alloy was thoroughly stirred, fluxed and skimmed and then chill-cast into notch bars. The aIlalyses of the three materials are given in Table I. The alloys for the determination of the solid solubility of iron in aluminum were prepared by melting 600 g total of the aluminum plus the required quantity of the aluminum-iron alloy (No. 92531). These

Jan 1, 1949

By G. K. Dumbauld, B. E. Morgan

Kesults of laboratory investigations of the effects of drilling muds on oil well cements are presented which show that relatively large quantities of untreated muds do not seriously interfere with the setting of cement slurries, but that relalively small quantities of treated muds seriously retard the setting of cement slurries. Laboratory results also indicate that the harmful effects of contamination with treated muds can he counteracted by the addition of activated charcoal to cements. Also described is the successful use of cement containing activated charcoal for the placement of plugs in oPel hole after previous attempts with ordinary cement had been unsuccessful. INTRODUCTION The contamination of cement slurry by dilution with drilling mud has long been considered a cause of failure in oil well cementing. The cement slurry must displace the drilling mud from the annulus between the casing and the walls of the borehole. and it is probable that some mixing of the slurry and the mud occurs even under the most nearly ideal displacement conditions. Hole enlargement, failure to center the casing in the hole, and formation of gel structure in the drilling mud increase the probability of contamination. In some cementing operations, such as the placement of a cement plug in open hole, considerable mixing of the mud and slurry is likely. Many cement failures which can be attributed logically to no cause other than contamination of the cement slurry by the mud attest the need of a better understanding of this problem. Considerable attention was given to the problem of mud contamination of cements about 20 years ago.The effects of field mud upon cement slurries prepared with different amounts of mix water were investigated thoroughly, and the data obtained were invaluable in determining the causes of the high percentage of failure in oil-well cementing at that time and in bringing about improved cementing results. Since then, many aspects of the problem have changed, due primarily to advancements in cement and drilling mud technology. Today, several types of portland cement are used in well cementing and numerous chemical additives are used in drilling muds. An excellent report on the effects of drilling mud additives on oil-well cements was issued during 1951 by the American Petroleum Institute. Data in the report revealed that many mud additives, notably organic materials in relatively small amounts, produce a marked effect on the properties of cements. Prior to this time, little information has been available on the effects of chemicals commonly used in the treatment of drilling muds upon the properties of cements. Another aspect of the problem of mud contamination of cements, which has received no attention heretofore, is the possibility of producing a cement having properties unaffected by a reasonable amount of mud contamination. In view of the need for additional information on the contamination of present-day cements by currently-used drilling Muds, the investigation described herein was initiated Several years ago with a two-fold purpose: first, to determine the capacity of cement slurries to tolerate contamination by both untreated and treated muds without loss of ability to set and develop strength within a reasonable time; and, second, to investigate the possibility of enhancing the ability of cement slurries to withstand mud contamination by incorporating additives in the cement. The data for this study were obtained by mixing drilling mud with cement slurry and testing the resulting slurry-mud mixture for rate of set and development of strength. Also, several materials were tested for their possible improvement of the property of cement slurry to withstand mud contamination; these materials were tested in both contaminated and uncontaminated cement slurries.

Jan 1, 1952

By H. C. H. Darley

Particles of montmorillonite-type clays consist of plate-like clay crystals stacked face to face. Under certain conditions in a suspension, these particles disperse to individual platelets with the formation of diffuse double layers round each platelet. This action has a profound influence on the rheo-logical and other properties of the suspension. This paper describes a test for degree of dispersion and uses this test to correlate changes in dispersion with changes in viscosity and gel strength. The test is of practical value in determining and controlling dispersion in drilling muds. INTRODUCTION It has long been recognized that the hydration and dispersion of clays, particularly those of the montmoril-loilite type, strongly influences the rheological and other properties of drilling muds, but little has been done to measure either of these phenomena under conditions that exist in drilling muds. The hydration of clays as such has been extensively studied by those interested in clay mineralogy, but in drilling muds it is to be expected that dispersion is at least as important a factor as hydration because of the much higher water-to-clay ratios and the very high degree of mechanical agitation. The term dispersion as generally applied to colloidal systems means the subdivision of large particles to small. Particles of montmorillonitic clays, however, consist of plate-like particles stacked face to face. Dispersion of these aggregates to individual platelets may be expected to have an unusually large influence on the properties of the suspension because of the shape factor, the enormous increase in specific surface, and the pronounced surface phenomena exhibited by the crystal surfaces. It is this form of dispersion that is particularly considered in this paper, -and the term degree of dispersion is used to imply the number of platelets per particle. The term aggregation is used to denote the opposite of dispersion, the association of individual platelets face to face to form stacks. It is important, as Garrison&apos; has pointed out, to distinguish between the deflocculation-flocculation phenomenon and the dispersion-aggregation phenomenon. Flocculation of clay suspensions is characterized by the formation of voluminous sediments that are stable under quite high centrifugal fields. This indicates an edge to plate association of particles to form an open network type of structure, which obviously will have quite a different influence on the properties of the suspension than aggregation of the platelets face to face. The work described in this paper was primarily concerned with developing a test for degree of dispersion in clay suspensions and by means of this test to follow changes of dispersion brought about by addition of electrolytes and to show the influence of dispersion on the rheological properties. The Clay-Volume Test This test is based on the assumption that the greater the number of particles per unit weight of clay in a suspension the greater will be the volume of sediment when it is flocculated under standard conditions and centrifuged. After considerable experimentation the following procedure was established: 1 cc of the test mud vigorously shaken with 100 cc of 1-N NaCl in an ASTM oil centrifuge tube and centrifuged for five minutes in an International No. 2 centrifuge at 2,000 rpm. When drilling fluids of different solids content are being compared, the clay volume is expressed in cc per gram of clay solids, but generally changes in dispersion in a given mud are being compared and it is more convenient to report as cc of sediment. The test is strictly a comparative test, so that it is not necessary to adhere to the conditions specified above, e.g., with field muds a stronger flocculant such as Al2(SO4)3 may be preferable to NaCl.

Jan 1, 1958

By F. C. Langenberg, J. Chipman

New data on the distribution of silicon between slag and carbon-saturated iron at 1600oand 1700oC are presented which, in combination with previously published data, permit the determination of silica activities over a broad range of compositions in the CaO-Al2O3-SiO2 system. The distribution of silicon between graphite-saturated Fe-Si-C alloys and blast furnace-type slags in equilibrium with CO has been described in previous publications.1"3 In this past work the silica-silicon relation was established at temperatures of 1425" to 1700°C for slags containing up to 20 pct Al2O3. This paper presents the results of additional studies at 1600" and 1700° C which extend the silicon distribution data at these temperatures for CaO-A1203-SiO2 slags over a range from zero pct A12O3 to saturation with A12O3, or CaO.2A12O3. The upper limit of SiO, is set by the occurrence of Sic as a stable phase when the metal contains 23.0 or 23.7 pct Si at 1600" or 1700°C, respectively. The activity of silica over the expanded range is determined directly from the distribution data.3 Recently, 4-7 other investigators have studied the activities of SiO, and CaO, principally in the binary system, using different methods and obtaining somewhat different results. EXPERIMENTAL STUDY The experimental apparatus and procedure have been fully described in previous publications.1, 3 Six new series of experimental heats have been made, four at 1600° and two at 1700°C. Master slags of several fixed CaO/A12O3 ratios were pre-melted in graphite crucibles, and these were used with additions of silica to prepare the initial slag for each experiment. Slag and metal were stirred at 100 rpm and CO was passed through the furnace at 150 cc per min. The initial sample was taken 1 hr after addition of slag at 1600°C or 1/2 hr after addition at 1700°C. The run was normally continued for 8 hr at 1600°C or 7 hr at 1700°C, and the final sample was taken at the end of this period. Changes in Si and SiO2 content indicate the direction of approach to equilibrium, and in a series of runs where the approach is from both sides this permits approximate location of the equilibrium line. Fig. 1 shows the results of such a series of 15 runs at 1600°C for slags of CaO/Al2O3 = 1.50 by weight. Figs. 2 and 3 record other series at 1600°C and Fig. 5 a series at 1700°C with fixed CaO/Al2O3 ratios. The results of the experiments at 162003°C have been reported in part in a preliminary note.3 In the experiments recorded in Figs. 4 and 6, the slags were saturated with A12O3 (or with CaO.2A12O3 within its field of stability) by suspending a pure alumina tube in the melt during the course of the run. The final slag analyses were used to establish the liquidus boundaries8 in the stability fields of CaO.2Al,O3 and of A120,. ACTIVITY OF SILICA The free-energy change in the reaction has been calculated by Fulton and chipman2 from recent and trustworthy data including heats of formation, entropies, and heat capacities. The more recent determination by Olette of the high-temperature enthalpy of liquid silicon is in satisfactory agreement with the values used and therefore requires no revision of the result which is expressed in the equation: SiO, (crist) + 2C (graph) = Si + 2CO(g.) [1] &F° = + 161,500 - 87.4T The standard state for silica is taken as pure cristobalite and that of Si as the pure liquid metal. Since the melts were made under 1 atm of CO and were graphite-saturated, the equilibrium constant for Eq. [I] reduces to K1 = asi /asio2 The value of this constant is 1.77 at 1600°C and 16.2 at 1700°C. Through K1, the activity of silica in the slag is directly related to the activity of silicon in the equilibrium metal.

Jan 1, 1960

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By J. A. Herrick Nashua

IN this country steel made in a Siemens furnace or Bessemer converter, is generally tapped into a ladle or shoe, and then drawn through an aperture in its base into the various moulds. In order to regulate the flow of the molten mass a refractory valve is arranged at the aperture. A plumbago nozzle is fixed firmly in this aperture, and a stopper of like material is fitted to it, making a socket valve. In order to raise and depress this stopper at will, a rod is fastened-to it, extending through, the metal and over the brim of the ladle, where it is bent back in a half circle and secured in a slide. This slide plays vertically in a frame, permanently fastened to the outside of the ladle, and is moved by a lever having as a fulcrum a pin fixed in this frame, one end, of the lever being temporarily fixed to the slide, and the other end being moved by hand. Reference being had to the drawing (see Plate 1, Fig. 1), E is the nozzle, D is the stopper, A is the rod, protected as hereinafter described, C is the cast-iron framework, B is the wrought-iron slide, B&apos; is the offset into which the rod, A, enters, and is secured in the usual manner by a key, a. Section J, K, shows the manner of hanging the lever. J is a pin attached to the slide by which the end of the lever raises the slide, B. J is the fulcrum fastened to the frame, C. K (Fig. 1) is a hand-nut fastening the slide, B, to the frame, C, at will. Fig. 2 is a side elevation of ladle, showing the outside working of the parts above described. It is the common practice to protect the rod, A, by a coating of clay and fire-sand, kneaded to the right consistency and applied to the rod, and then thoroughly dried. Just before casting, the plumbago stopper, D, is heated at its extremity to redness separate from the ladle and, at the moment of pouring, is placed in the ladle and slide, and adjusted as well as practicable. Some very serious defects ensue, causing much trouble and vexation as well as actual loss. The fire-clay coating in drying becomes cracked and seamy, and at its best is more or less loose on the rod. The hot metal sometimes cuts

Jan 1, 1879

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strain-aging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that, wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 72o°C. The time of treatment is relatively short (about 3 hr, to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say aimost 30 per cent by volume. At this temperature. the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a verv low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,-ooo lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantiallv constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1944

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.&apos; The specific conductances ranged from about 100 ohm-&apos; cm-&apos; for pure Cu2S to 1500 ohm-&apos; cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-&apos; cm-&apos;. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne&apos; detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-&apos; cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-&apos; cm-&apos;.&apos; Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.&apos; A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By W. M. Gray

The determination of the state of stress existing at a point in any solid body requires the determination of the six components of the stress tensor relative to a convenient set of axes. One general method of doing this in rock is to make strain or deformation measurements associated with local relief of stress in a number of boreholes penetrating a limited volume in the vicinity of the point at which the stress is to be determined. The stress is assumed to be constant throughout this volume. Leeman1 has described a number of the instruments that have been developed for making deformation or strain measurements in boreholes. Panek2 has described the application of statistical methods to the determination of the average components of ground stress from sets of measurements made in boreholes by means of deformation meters of the type developed by the U.S. Bureau of Mines. In this paper attention is given initially to the strain cell developed for use on the flattened ends of boreholes by the Council for Scientific and Industrial Research (CSIR) , South Africa. The equations required for evaluating the average components of ground stress from measurements made by means of the CSIR strain cell are derived. These equations are similar in form to those applying to measurements made by the borehole deformation meter developed by the U.S. Bureau of Mines. The results of an investigation of the properties of the equations are described. These results are important in the practical use of both the instruments mentioned above and any instrument based on similar principles.

Jan 1, 1968

By H. A. Guess

Introduction. History and Production Statements. Southeast Missouri is the oldest of the large producing districts of the United States. The first recorded production from disseminated ores was in 1869, although for many years prior to that time lead had been milled from shallow pockets, and steady growth in production has been shown ever since, the greatest increases being during the past five years. The production by years for each of the operating companies from 1869 to 1907, inclusive, is given in Table I. In Table 11. is given the production by years from 1908 to 1912, inclusive, for the district as a whole, showing the tonnage of crude ore mined, yield in concentrates, average assay of concentrates; yield in metallic lead both per ton of crude ore and in total; also approximate value of the yearly production. It is interesting to note that the production for the 5-yr. period 1908 to 1912, inclusive, is practically equal to the total previous production, viz., the 39-yr. period 1869 to 1907, the summary being as follows:

Jan 1, 1915

By S. F. Emmons

The first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre in May, 1871. It is entitled " The Geographical Distribution of Mining Districts in the United States," and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from a geological stand-point. At the request of Dr. Raymond I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such pub-

Jan 1, 1894

By J. W. Galpin, R. H. Allen

Controlled pre-grouting is a technique developed during a period of more than ten Years experience, in an effort to produce safer, drier and more economical mine shaft sinking. The technique involves a knowledge Of hydro-mechanics, both static and dynamic, and a series of specially formulated grout mixtures to obtain several desired results through precontrolled setting time. In general, the following procedures have been used to secure the best results in controlled pre-grouting: I. Before drilling is commenced, One Of two decisions is made: one procedure, a modified form of the Francois method, is to stage drill and grout, that is, drill a limited portion of the hole, then grout and redrill that section which has been grouted, progressing in stages until the required depth is reached. We prefer this method because no casing Or grouting packers are required in the bore hole. This eliminates the risk of losing them in the bore hole due to packer failure, which might result in the expense of drilling a new grout hole. Another feature Of this approach is that smaller drill holes may be effectively used, further reducing the costs. One drawback, however, is that because of the open and small size hole, it is impractical to attempt water draw-down tests. The second alternative is to drill the bore hole, (generally NX size), to the re-quire~ depth. he casing and grouting packer are placed in the bore hole at the lowest packer setting. A small, portable, power driven, swabbing device is used in the grouting casing to test the packer and remove mud or cuttings from the bore hole below the packer. The hydrostatic level is recorded and a close estimate or test is made of the quantity of water at each packer setting. Grouting progresses upward in a series of packer settings to the surface. Occasionally, casing is inserted in the bot-tom of the bore hole from within the mine, and water pressure and volume can be obtained in this manner. This is usually dangerous because of the unknown quantity of water. 2. The grouting, mining and geological engineers at the drill location make a detailed examination of the cores and also locate proper and firm grouting packer locations. A competent driller,s opinion should be given due consideration as to the character and condition of the bore hole. 3. Several samples of formation water

Jan 1, 1949

By F. L. Sizer

The mining regulations of British Columbia and Mexico present some features which might well be copied in the United States, if we are to have a complete revision of the laws governing mining titles. 1. First and foremost is the "squarc" location, which would mean the abolition of extralateral rights. This is a condition in both of the countries above named which has seemed to work no hardship upon any one, and certainly the limitation of underground rights by vertical planes through all lines makes a locator&apos;s rights clear. In view of the long and costly litigation which has involved so seriously many of our most important mining districts, it would seem to be the part of wisdom to avoid a repetition of similar trouble on titles of lode mining claims, by the enactment&apos; of a law similar to that in force in British Columbia. Objections have been raised by .representatives of English companies to the investment of large amounts of money in mining operations in the United States, because of the insecurity of title under the &apos;present apex law; and the statement has been made to me personally by one of the largest English operators, that he would .never again consent to the purchase of mines in the United States, preferring Mexico with all its revolutionary troubles to the danger of encroachment upon his underground rights by an unscrupulous neighbor. Without going into further argument as to the desirability of the I(square location," it should be sufficient to say to those who are inclined to "let well enough alone" and still stick to the "law of the apex" that there have never been any serious objections raised to this feature of the square location in either British Columbia or Mexico. There are well founded and logical reasons for abandoning the doctrine of extra-lateral rights since it is so difficult of interpretation; the most natural substitute being a law similar to that of British Columbia, giving to each locator an area 1,500 ft. square. I would advocate the right to locate adjoining claims of equal extent on either side of the discovery claim, on the strike of the lode, subject to a seasonable requirement in the matter of work upon them; and in the case of a vein dipping flatter than 45&apos; from the horizon, or in case of a

Jan 1, 1915

By Charles T. Holland

IN connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter [ ] into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. STRENGTH OF COAL It is generally agreed that one of the necessary conditions for bumps is a strong [ ] coal.1 Therefore, since the strength of coal is an important factor, a study of this property should be made. Several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines8 and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semibituminous (Pocahontas No. 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the same coal.

Jan 1, 1942

By E. Amott

A test is described in which the wellubility of porous rock is measured as a function of the displacement properties of the rock-water-oil system. Four displacemet operations are carried out: (I) sponlaneous displaceti?ent of water by oil, (2) forced displacement of water by oil oil in the same system using a centrifuging procetllrre, (3) spontaneous displacement of oil by water. and (4) forced displacment of oil by water. Ratios of the spontaneous displacement volumes to the total displucenlent volumes are used as wettability indicates. Cores having clean mineral surfaces (strongly preferentially water-wet) show displacement-by-waler ratios approaching 1.00 and displacement-by-oil ratios of zero. Cores which ([re. strongly preferentinlly oil-wet give the reverse resu1ts. Neutral wellability cores show zero values for both ratios Fresh cores from different oil reservoirs have shown wettabiltties in tlris te.st covering rrlti~ost 111e conlplrtt, range of thr: te.st. Notvever, nlo.s/ of tlle fresh California cores tested were slightly prcfere111icrlly wclter-\vet. The chrrnge.~ in coro u (&apos;liabilities, as indicated hy this te.st, r~.sril/ing from various CO~P hanrlling procedures tt,ere oh.served. In sonie ca.sc,s /Ire ~,cttahilitio.c. of fresh cores were changell by drxi:~g or 11y e.x/rclct ing with iolcreiii~ or. dioxunc~; in o/h~r cases they were 1101 changed. Co~ltrrc/ of cort,.s ~.ith filtrc~t~c. from water-base rlrilling rilrrrls crlrc.sed littlc change in we/ /ahility ivhile contnct with filtrates frorii oil-hus~ ri1rlcl.s tlecrrascrl the prefcrerlcc, of the, cores for )I.NI Usitig thi,s test to ri.crl~lute n~r~ttubili~y, N .vt~ldy was iilarle of /lie correlmtio~i of wettability with wa/erfloocl nil recovery for orttcrop Ohio sand.stone and for Al~ln-tlunl. Resul/.v indicate thml no single correlatioti between these factors applies to different porous rock syste~n. It is thought that diflerences in pore gen~netry resrrlt in diflrrerrce.~ in this correlurio~z. INTRODUCTTON Most investigators who have reported on the wettahility of porous rock have described such rock as prcferentially water-wet or preferentially oil-wet. In some cases a third classification, neutral wettability. has been used. The efficiency of water floods in each of these wettability groups has been described in numerous publications. Several methods for characterizing porous rock wet tability more precisely have been reported,&apos; " but it appears that because of one weakness or another. none of these has been generally accepted. Early in our studies in this field, it was found that the displacement efficiency of oil by water in a particular porous rock having a strong preference for water was quite different from that in a similar rock having only a moderate preference for water. Thus, there appeared to be a need for a practical, reasonably precise wet tability test. one which could classify porous rocks into 10 to 20 different groups rather than the two or three broad groups listed above. The test developed to meet this need is described in this paper. Also, changes in wettability, as indicated hy this test, resulting from various core handling procedures are discussed. Finally, data showing the corrclation of wettability with waterflood oil recovery for two different types of cores are presented and discussed. Some confusion has resulted from the failure of certain writers to define clearly some of the wettability terms they have used. Accordingly, the following commcnts concerning definitions are offered. The wc t ta-hility of a solid surface is the relative preference of that surface to be covered by one of the fluids under consideration. It is felt that this is the generally accepted definition. The fluids being considered must bc specified (or understood) before the term wettability has any significance. In the work reported here these fluids are water (3 per cent brine) and oil (kerosene). The term preferential wettability is sometimes used, but we think that the word preferential is redundant here and should not be used. Tn line with the definitions of Jennings&apos;, a preferentially oil-wet solid surface is regarded as a surface which will show an oil advancing contact angle less than 90" (measured through the oil) in the water-oil-solid system. Oil will spontaneously displace water, if both are at the same pressure, from such a surface. A preferentially water-wet surface is analogous. This is consistent with the wettability definition above. As Jennings has said, frequently the term oil-wet is used to mean the same thing as preferentially oil-wet. However, oil-wet also has been used occasionally referring to an oil-covered surface when the availability of water was limited. To avoid confusion from this source, we do not use the terms oil-wet and water-wet. DESCRIPTION OF WETTABTLITY TEST The following points were considered desirable in a wettability test for our purpose. 1. The test should be a displacement test resembling

By Yuri D. Tretyakov, Robert A. Rapp

The stoichiometry ranges ofNiOl+y and LiFe,O,-d were established by high-temperatwe electrochemical meas7rements in a stabilized-zirconia electrolyte cell. The results were consistent with doubly ionized cation vacancies in NiO,+y and interstitial lithium or iron ions in . The defect structure of the ternary ferrite was derived from the consideration of equilibration with respect to oxygen between the solid and the gas phase. The absolute magnitudes of defect concentrations were calculated. Pavtial molar enthalpies of oxygen in the compounds were calculated and interpreted in terms of the enthalpy of defect formation in these crystals. NICKEL oxide (NiO,,?) is a metal-deficient, p-type, extrinsic semiconductor whose properties are consistent with a structural model based on the presence of cation vacancies as the predominant ionic defect at sufficiently high temperatures and oxygen activities. A survey of previously reported conductivity studies and the presentation of some more recent conductivity measurements will be given in a later paper.&apos; The absolute magnitude of the equilibrium vacancy concentration in NiO has been reported from combined conductivity and thermogravimetric data of &apos; However, disagreement exists concerning the state of ionization of the nickel vacancies in NiO. Some authors3-&apos; have proposed that the predominant defects in NiO are singly ionized nickel vacancies and positive holes (h&apos;) formed by the reaction where, accorhng to the notation of Kroger and Vink,6&apos;7 Oq represents an oxygen ion on its normal lattice site. Other authors"27E have proposed that doubly ionized nickel vacancies (V{i ) and positive holes are predominant and are formed by the reaction One purpose of the present investigation was to establish the nature of the predominant defect in NiO,+? as well as its equilibrium concentration and thermo-dynamic properties at elevated temperatures and known oxygen activities. To accomplish this purpose, the coulometric titration of oxygen into and out of NiO was accomplished using a galvanic cell involving the calcia-stabilized zirconia electrolyte. The ternary oxide, lithium ferrite (LiFe50,-6) is ferromagnetic and has the inverse spinel structure LiFe,O,-d Thus, in the ideal stoichiometric XY204 lattice, Fe3 ions occupy one-eighth of the tetrahedral (A) sites, and i&apos; and Fe3&apos; ions share at random one-half of the octahedral (B) sites within the fcc sublattice of oxygen ions.g The structure and thermodynamics of the spinel structures have been comprehensively decribed.&apos;-&apos; A recent compilation of literature for lithium ferrite is also available. 15 Oxygen-excess LiFe50sis not expected to exist because both i&apos; and 17e3& ions are in their highest normal valency states (positive hole formation is not favorable). As will be discussed, equilibration of the ferrite crystal with oxygen of a surrounding gaseous phase will result in the introduction of equilibrium concentrations of ionic and electronic defects. In the Results and Discussion section a defect model for LiFe50,-d is proposed. This defect model is tested by high-temperature coulometric titration experiments. EXPERIMENT The oxygen activities in nonstoichiometric NiOl+, (and also LiFe,O,-d) were measured by means of coulometric titration with the high-temperature galvanic cell The critical characteristic of a suitable experimental cell is the complete isolation of the phase to be investigated in a minimum sized chamber which is free from extraneous sources and sinks for oxygen (leakage). Then oxygen is only admitted to the chamber or removed from it in known amounts by coulometric titration, which involves the passage of oxygen ions through the solid electrolyte with electrochemical oxidation and reduction reactions at the platinum contacts to the electrolyte. The experimental cell is shown in Fig. 1. The cap of the cell was the tip from a closed-end alumina tube, which was found to be leak-free from a helium leak-detector test. This alumina cap was about 1.2 cm OD and about 1.5 cm high. A Zircoa calcia-stabilized zirconia tablet (crucible lid) of 1.5 cm diam and 0.3 cm thickness served as the solid electrolyte. A Pyrex ring of about 0.1 cm thickness was placed between the electrolyte and the cap. The electrolyte tablet was painted with platinum paste on the entire outer face and on that part of the inner face which would be within the enclosure; these electrodes were further prepared by heating in air at 1000°C for 2 hr. Nickel oxide powder, listed as 99.999 pct pure, was purchased from Leico Industries, Inc. Pills of the NiO were cold-pressed and sintered at 1050°C for 3 hr in a platinum crucible. This poorly sintered NiO was crushed, and chunks were wrapped in 52-mesh Pt gauze (to catalyze the solid-gas exchange) for place-

Jan 1, 1970