Search Documents

By R. J. Pearce, I. Whittle, J. J. Stobbs

The oxidation kinetics of UCu5 in carbon dioxide have been studied over the temperature range 350° to 850°C. At any one temperature, two successive parabolic rate constants are obtained. Up to 650°C, the temperature dependence of the reaction is snzall and the first parabolic rate constant is higher than the second. At temperatures of 690°C and above, there is a very marked temperature dependence and the second rate constant is the higher. Metallo-graphic examination has shown that attack proceeds via internal oxidation. THE oxidation behavior of the U-Cu intermetallic compound, UCu5, in carbon dioxide was briefly examined during investigations aimed at selecting oxidation-resistant uranium-alloy coatings.' It was found that an extremely thick, coherent scale was formed coated at the scale-gas interface with a thin, apparently continuous layer of copper. A more detailed investigation of the oxidation of UCus has now been made. Previous published work2 has been limited to a brief examination of UCu5 in connection with the oxidation of a U-1 wt pct Cu alloy in carbon dioxide. No attempt was made to explain its behavior, but the work indicated that attack proceeded by intern oxidation, with the formation of a layer of copper on the surface of the specimen. EXPERIMENTAL UCus was prepared by arc melting the stoichio-metric amounts of high-purity copper* and uran-

Jan 1, 1965

By J. C. Todd

The volume of air needed to move the combustion wave through each acre-foot of the reservoir is a very important quantity for engineering economic analyses. A new method, which involves backflowing the injection well, has been developed for determining the air requirement .for the forward combustion thermal pilot in the Delaware-Childers field. The method depends on measurement of the total volume of air injected and measurement of the pore volume in the zone swept out by the combustion front. The basic premise of the method is that the pore volume of the swept zone contains air, while the formation around this zone contains flue gas, oil and water. The pore volume of the swept zone is determined by blowing down the pilot section of the formation through the injection well after the pilot is shut down. Oxygen balance is used to differentiate between air from the swept zone and flue gas from the surrounding formation. Data indicate that air'is produced from the swept zone by relatively efficient miscible displacement by the flue gas. The pore volume occupied by the air in the swept zone is determined by simple PVT relationships. The average temperature of the swept zone is calculated by heat balance from the total amount of heat generated during the pilot and losses to the surrounding formation. The new method was applied successfully at the conclusion of the pilot in the Delaware-Childers field; the air required for the reservoir conditions involved was calculated to be 19.2 MMscf/acre-ft of reservoir swept. INTRODUCTION One of the most important pieces of information to be found from a forward combustion pilot is the air requirement; that is, the volume of air needed to move the combustion wave through each acre-foot of the reservoir. Compression costs per barrel of oil recovered, which are a direct function of the air requirement, are a large portion of the expenses incurred in the thermal recovery process. Thus, the profitability of thermal recovery depends largely on the air requirement, which is a measure of the amount of fuel deposited and burned in the thermal recovery process. Several attempts have been made to correlate crude oil properties with fuel deposition and, hence, air requirement.l*2 Other attempts have been made by our laboratory to find the air requirement by material balance, gravity survey, pressure transient analysis,3 magnetic survey and the poten-tiometric model. Better methods are needed to predict more accurately the economics of fieldwide application of the process. Another method of finding the air requirement consists of operating a pilot thermal project for several years. This is followed by an extensive coring program to define the volume swept by the combustion wave. The air requirement is found from the total injected air divided by the volume of the swept region found from the coring operation. This method is costly; an adequate coring program usually costs several hundred thousand dollars. A thermal pilot was operated in a watered-out portion of the Delaware-Childers field, Bartlesville sand, from Nov., 1960, until May 3, 1965. One of the primary purposes of this pilot operation was to determine the air requirement for economic calculations which determine the advisability of expanding the project to the entire 128,000 acre-ft field. Barnes4 has described the result of this pilot operation,, including calculation of the air requirement from limited coring data. The value obtained, as calculated, was 15.8 MMscf/acre-ft. One purpose of this report is to describe a new method of finding the air requirement from a thermal pilot operation. A second purpose is to describe the application of this method to the Delaware-Childers thermal pilot. THEORY AND DESCRIPTION OF THE METHOD The combustion zone in the forward combustion process is propagated from injection w producing

Jan 1, 1970

Henry D. Hibbard, Plainfield, N J. (communication to the Secretary*):—This very interesting history is a valuable addition to our knowledge of the basic process and its introduction to this country. In addition to the attempts noted in the paper which were made here to establish the basic Bessemer process, and the experiment with the Siemens-Martin process at the Otis works, there were others made with the latter-named process at about the same date, all of which failed or, at least, were discontinued. The first attempt which survived was that of Carnegie,

Jan 1, 1911

By R. L. Smith, J. L. Rutherford

ALTHOUGH considerable effort has been devoted toward the determination of the mechanical properties of pure metals, it is extremely difficult to compare the results of such work. This is because of differences in method and type of test, grain size, heat treatment, and purity of material. There is very little information on the properties of most of the high melting point reactive metals with purities greater than 99.9 pct. Previous evidence concerning the tensile properties of unalloyed metals show that: body-centered-cubic metals are brittle at low temperatures; face-centered-cubic metals remain ductile; some hexagonal metals remain ductile, others become brittle. It may be that traces of impurities decrease the low temperature ductility of the body-centered-cubic lattice. This would suppose that a body-centered-cubic lattice free from impurities would exhibit nearly the same ductility as a face-centered-cubic structure. The present investigation has been an evaluation of the tensile properties of zone refined iron in order to determine whether higher purity material than that previously evaluated behaves differently. Experimental Procedure In this investigation, high purity iron was zone purified using the floating zone method.' The starting stock was obtained from two sources. The first,

Jan 1, 1958

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By J. G. Giddings, R. Kobayashi

Residual viscosity, the ViSCOSitY at a given pressure and temperature minus the dilute gas viscosity at the same temperature, has been found to be independent of temperature for pure components and mixtures for simple molecules and light hydrocarbons. The residual viscosities for methane, ethane, propane and four mixtures were correlated as a function of reduced density and molecular weight. INTRODUCTION Earlier efforts in correlating the viscosity of light hydrocarbons and associated gases under pressure, primarily by some form of the corresponding states principle, have been reported elsewhere.7 The formal theory of corresponding states principle for viscosity from non-equilibrium statistical mechanical arguments for simple molecules has been developed by Helfand and Rice.13 The most serious obstacle to the development of a generalized corresponding states representation of viscosity data, even for simple molecules, has been the limited quantity of precise viscosity data of pure components and mixtures over a wide range of pressure and temperature conditions. Viscosity data on light hydrocarbons have recently been contributed by several laboratories.2,6,8,23,25,26 In the study of the viscosity of nitrogen, Michels and Gibson" observed that the viscosities of nitrogen as a function of density gave parallel isotherms. The same behavior has since been reported for other gases.".= The observed behavior indicates that the residual viscosity or the viscosity at a given pressure and temperature minus the dilute gas viscosity at the same temperature is a unique function of the density. Abas-Zade,1 Michels and Botzen,18 and Michels, Bot-Zen, Friedman and Sengers,19 observed similar behavior for thermal conductivity, the residual thermal conductivity being defined in a manner parallel to that of residual viscosity. Thodos and co-workers 4,15,24 applied the residual viscosity concept to the viscosity of pure monatomic and diatomic gases. Ellington and co-workers10,25 made the residual viscosity vs density plots for ethane and propane, but omitted the region below a residual viscosity of 15 micropoise and showed a systematic separation of the ethane isotherms in the low density region. Eakin correlated the residual viscosity of methane, ethane, propane and n-butane empirically as a function of density and molecular weight: Carmichael and Sage6 recently presented ethane residual viscosity vs density values in the gaseous liquid, and near critical regions as a single univariant function of density. Flynn, Hanks, Lemaire and ROSS" have contributed extremely accurate viscosity data to confirm that the residual viscosity concept is essentially correct, but may not be accurate within 0.1 per cent of the viscosity value for the gaseous state- The recent studies by Giddings12 indicate that the residual viscosity of methane, propane and each of four methane-propane mixtures are unique functions of density Over the temperature and the density ranges studied.

Jan 1, 1965

By Henry Louis

Four alloys of gold and silver were prepared, containing the metals in the following proportions by weight: I. Gold:Silver::1:2.62.

Jan 1, 1894

By R. K. Waring, E. C. Truesdale

The Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO+ CO = Zn + CO2 [1] C + CO2 = 2 CO [2] Each of these reactions is dependent upon the other for the supply of CO and CO2 , respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2 O [31 C + H2O = CO + Ha [4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between IIOO° and I3oo°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented. *

Jan 1, 1943

By E. C. Truesdale, R. K. Waring

The Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO+ CO = Zn + CO2 [1] C + CO2 = 2 CO [2] Each of these reactions is dependent upon the other for the supply of CO and CO2 , respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2 O [31 C + H2O = CO + Ha [4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between IIOO° and I3oo°C., . . . the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented. *

Jan 1, 1943

By C. T. Young, J. L. Lytton

In recent investigations,1,2 the strength and thermal stability of dislocation substructures prepared by 5 to 25 pct room temperature tensile straining and recovery annealing at 120°, 160°, and 200°C have been studied in randomly oriented polycrystalline high purity aluminum. The techniques of transmission electron microscopy revealed that a major source of the strength and stability of dislocation substructures was the formation, during room temperature straining, of well-defined cells bounded by dislocation tangles which rearranged into nearly perfect dislocation networks during recovery, forming the boundaries of subgrains. The strength of such substructures increases with decreasing cell or subgrain size,2"6 and the formation of fine subgrain structures can provide thermally metastable strength at low temperatures and can favorably alter the course of primary creep at elevated temperatures.7'8 For maximum benefit, however, sub-grain growth should be reduced or eliminated. It was, therefore, decided to investigate the use of heterogeneous precipitation on dislocation networks as a means of imparting increased strength and thermal stability to subgrain structures through effective pinning. C.T. YOUNG, STUDENT MEMBER AIME, and J. L. LYTTON, Member

Jan 1, 1970

By John F. Allan

This paper does not pretend to advance any facts or improvements not known to many members of the Institute, but is intended merely to give a few practical hints on preliminary tests, and to call attention to a possible enlarged field for the cyanide process in the treatment of some silver-ores, which merits investigation. Broadly considered, the choice of a process for the treatment of silver-ores in Mexico is confined to the following alternatives: (1) Concentration for treatment by smelting; (2) milling and pan-amalgamation; (3) the patio and Ortega process; [4) chloridizing roast and lixiviation; (5) chloridizing roast and cyaniding; and (6) cyaniding of the crude ore. These methods of treatment may also be combined, and cyaniding or concentration, or both, may be introduced, at what-ever stage it is found to be most advantageous. The characteristics of the ore (especially its gold-content) and local conditions, such as distance from railway, cost of fuel, amount of water available, vary so much that it is impossible to make general comparisons between the different processes, either as to extraction or cost. Concentration and subsequent smelting may be made very expensive by long-distance transportation of concentrates; pan-amalgamation is undoubtedly expensive; and the patio process is barred when the ore contains appreciable amounts of gold, by reason of its poor extraction of that metal; yet there are many ores for which each of these processes is especially adapted, and the expense of treatment is compensated by the results obtained.

Jan 1, 1905

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker's data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949

By T. H. Weldon, L. V. Whiton, R. R. McNaughton, J. H. Hargrave

R. H. McNAUGHTON*—The Smelting Co. and Mr. Reid and his men at Selby are to be congratulated on the job they have done on sinter gas recircula-

Jan 1, 1950

By R. Roberge, H. Herman

Jan 1, 1969

By Roger N. Dokken

It is well-known1-4 that Fe-Si alloys from approximately 9 to 27 at. pct Si show an ordered structure of the Fe3Si type at room temperature. Recently Meinhardt and Krisement,' through an investigation of Fe-Si alloys at room temperature by neutron diffraction, discovered that at 10.8 at. pct Si ordering of the FeSi type occurs while above this composition the normal Fe3Si-type superstructure appears. This FeSi type of ordering was also found by Davies8 as indicated by X-ray diffraction measurements on an Fe-8.7 at. pct Si alloy. Meinhardt and Krisement7 extended their neutron-diffraction work and determined the phase-boundary temperatures for both FeSi- and Fe3Si-type ordering. Ordering phenomena can also be studied by resistance measurements.4,8-11 Krivoglas and Maty-sina" carried out a theoretical development of the

Jan 1, 1965

Robert H. Richards, Boston, Mass.: Mr. Goodale calls attention to the difficulty of obtaining clean tailings from the jigs which are fed by the spigots of the hydraulic separator. This difficulty is universally encountered. The Lake Superior copper mills practically overcome it by running the beds of those jigs loose, carrying into the hutch all of the available copper and some sand. These hutches are again jigged upon threesieve Collom jigs, where the treatment is very slow and gentle; and on the successive jigs lighter and lighter bedding is used. The last sieve is run thin enough to let some sand into the hutch. With these precautions most of the free copper is extracted, as well as a fair proportion of the included copper.

Jan 1, 1897

By William P. Blake

IntroductioN.............989 The Blake stone- Breaker Prize.......989 Great Labor-Saving Inventions.. 990 I. Biographical NoticE OF the Inventor......990 II. Former Methods of Breaking Stone......992 Ragging and Spalling......... 992 Cornish Rolls..........993 III. Construction of the Blake Stone-Breaker.. .. 993 The Lever.Pattern.........994 The Eccentric Pattern.........997 The Challenge Pattern......... 999 The Monarch Pattern.........1001 The Multiple-Jaw Pattern........1001 Movable Dies for Jaws......... 1004 Cheek.Plates,..........1007 IV. The Capacity OF Blake Breakers......1007 Position and Feeding of Breakers...... 1008 V. Gyratory Jaw Crushers.........1010 The Gates Rock- and Ore-Crusher......1010 The Comet Crusher.........1010 VI. Some Unusual Forms OF the Breaker......1010 The Smith Hydraulic Pattern.......1012 The Forster Crusher.........1012 The Stafford Crusher.........1013 The Gates Crusher.........1013 The Dodge Pattern.........1013 The Rawson Crusher.........1014 The Duplex Breaker.........1015 Booth's Modification of Wedge-Block......1015 Marsden's Eccentric Pattern.......1017 The Lancaster Machine........ 1017 VII. Combined Crushing and Grinding Impracticable,. . 1018 The Hanscomb Machine ...1019 Howland's Crusher and Pulverizer..1020 The Oliver Crusher and Pulverizer..1021

Jan 1, 1903

By A. J. Erickson, W. J. Garmoe

In mid-1970, Park City Ventures, a Utah partnership of Asarco and the Anaconda Company, initiated a six-phase exploration and development program in the Park City District, Utah. Geologic studies had delineated a number of exploration targets in several areas of the district. Discovery of ore in any of the target areas and continued favorable downdip development below then productive ore bodies would allow for reserve expansion and mill construction. The targets were: replacement mineralization in the Mississippian Humbug formation below productive ore bodies on the east flank of the Park City anticline; replacement mineralization in the Humbug formation in an unexplored fault block in the footwall of the Hawkeye structure on the east flank of the anticline; vein and replacement mineralization along the Silver Fissure; potentially higher grade replacement mineralization in the Humbug formation in a theorized structural block on the west flank of the anticline beneath the Ontario vein; replacement mineralization in the Permian Park City formation in the West End shaft area of the Silver King mine; vein mineralization along the Back vein in the Judge mine. In 1971 the Judge and Silver King Projects were suspended, due to a 30% cutback in the exploration budget. In spite of the cutback additional reserves were developed below the Humbug East Flank ore bodies; a major zone of ore grade mineralization was discovered along the Silver Fissure, five new ore bodies were found in the Humbug and Doughnut formations on the west flank of the anticline beneath the Ontario vein. First concentrates were shipped from a new mill in May 1975.

Jan 1, 1979

By W. D. Robertson, W. L. Phillips Jr.

Stress-strain curves were obtained for single crystals of alpha brass in tension and in direct shear. Specimens were strained various amounts in a given slip direction, unloaded, and immediately strained in a second slip direction 60°, 120°, or 180&apos; from the original slip direction. Crystals strained in tension and direct shear had comparable critical resolved shear stresses and stress-strain curves. The density of slip lines in direct shear and in tension was essentially the same. The stress-strain curves obtained in shear were independent of initial orientation, choice of {111 } slip plane, choice of <110> slip direction, prior annealing temperature, and rate of cooling after annealing. There was no recovery after annealing for 4 hr at room temperature or 200°C; recovery was observed after 4 hr at 400°C. The crystals showed no asterism and mechanical properties were completely recoverable up to 20 pct strain. It was found that there is a barrier to slip in all latent close-packed directions, and that the magnitude of these barriers, evaluated at 3 pct strain, is proportional to prior strain and independent of the choice of latent direction in the {111} plane. The formation of Cottrell-Lomer barriers is discussed as a possible explanation for the hardening of the latent systems. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of "easy glide," which is characterized by a linear stress-strain curve and a low coefficient, ds/dE, of work-hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In face-centered cubic metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close-packed planes, is the existence of secondary (latent) slip planes in the face-centered cubic crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.&apos;-.; However, the characteristic differences between individual face-centered cubic metals remain to be explained; in particular, it is not clear why the range of easy glide should vary so greatly in different metals and alloys similarly oriented for single slip. An investigation and comparison of different metals with respect to latent hardening on the primary slip plane should provide some of the information required to specify the necessary and sufficient conditions governing the transition from easy glide to turbulent flow. But, in order to accomplish this purpose, plastic strain must be produced by simple shear in a chosen plane and in a predetermined direction by some form of directed shear apparatus, the results of which must be correlated with the corresponding tension experiments. Two such experiments have been performed previously with zinc and with aluminum. Edwards, Washburn, and Parker" and Edwards and Washburn7 found that the strain-hardening coefficients in two latent directions in the basal plane of zinc were the same as in the primary direction. However, to initiate and propagate slip in either the [2110] or the [1210] direction, following primary slip in the [1l20] direction, it was necessary to increase the stress above that required to continue slip in the primary direction; when the direction of shear was reversed 180 deg plastic strain began at a much lower stress than that required to initiate slip in the original direction and the stress to propagate slip in the reverse direction was lower than the stress to continue slip in the forward direction, indicating a permanent loss of strain-hardening. Rohm and Kochendorfer observed softening in aluminum for all latent close-packed planes and directions. They also found that the critical resolved shear stress obtained from their direct shear apparatus was 50 pct lower than the value obtained from conventional tension tests, that the stress-strain curve was linear at 50 pct plastic strain, and that slip lines were not visible at strains less than 30 pct. At present it is uncertain whether these diverse results correspond to real differences in work-hardening characteristics of the close-packed planes of aluminum and zinc or to differences in experimental technique. In view of Read&apos;s analysis &apos;" of the stress distribution in the experimental arrangement of Rohm and Kochendorfer, there is some reason to question the significance of the latter results. In order to resolve this problem it is necessary to re-valuate the direct-shear technique and either repeat the previous measurements or investigate a third system. The latter choice seemed most likely to produce significant results with respect to work-hardening, and accordingly, it was decided to examine the hardening characteristics of the latent slip directions in alpha-brass. The choice of alpha-brass was dictated by the fact that easy glide is more extensive in this alloy than in any other face-centered cubic metal or alloy and, presumably, more nearly like the idealized hexagonal system. Experimental Procedure Crystals were made in graphite by the Bridge-man method in the form of cylinders, 11/2 in. diam and 8 to 9 in. long. Material for the crystals was 70/30 brass containing the following impurities:

Jan 1, 1959

By Reed W. Hyde

Some information has been published on the sulphur dioxide concentration of gases from D wight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes Over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide notation concentrates mixed with minus 20.mesh oxide ore, the mixture carrying 16,8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily. to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO z might be utilized, a series of runs was made to determine the concentration ofSO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1 2 to 1 in., (&apos;1 4 to 3% in. and (3) 6 to 5% in. The averages of the determinations from each series are platted On the graph (Fig, 1). The vertical scale shows the percentage by volume of SOz (as determined by the Reich method), and the horizontal scale shows the time e~pressed as percentage of the total sintering time. Sintering was considered to be complete when no SOz could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 Content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume usually will drop slightly toward the middle of the period and increase toward the end. However, this made is a reasonable approximation. several interesting features are brought out by these data. In general, the published data on SO 2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SOz in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 234 min. after

Jan 1, 1944