Search Documents

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By Sherwin F. Kelly

LITERALLY from the four corners of the earth, from Jerusalem and China, from Mysore and Uganda, as well as from geophysicists in the United States, came contributions from workers in magnetic and electrical geo-physical methods, most of them unfortunately unable to be present themselves. The most lively discussion centered on the phenomena of natural potentials in the earth, dealt with in M. B. R. Rao's paper from Mysore, and in Parke Dickey's contribution, which he presented in person. In the oil fields, the weak potentials observed in sedimentary strata traversed by bore holes have traditionally been ascribed to phenomena of electro-filtration and electro-capillarity. Research tending to refute this theory was presented by Dickey, who reported the existence of natural potentials in core samples, and between strata exposed in underground workings. This precipitated a lively discussion as to the possible role of electro-filtration, selective adsorption of ions by mineral particles, and electrolytic potentials, in the production of this phenomenon.

Jan 1, 1943

The next meeting of the Institute, the 113th meeting, will be held in Arizona in the latter part of September, 1916. All papers to be presented, at this meeting must be published in the September Bulletin or previously. Manuscripts must, therefore,' be in the hands of the Secretary of the Institute not later than July 1. In case manuscripts are given by authors to members of technical committees, or others, they must be in the hands of such persons sufficiently in advance so that they may be actually in the hands of the Secretary of the Institute by the date mentioned. In the past, the Secretary has received urgent requests for special consideration regarding manuscripts that come in after the closing date. In view of the obvious unfairness of this, the Committee on Papers and Publications has instructed the Secretary not to accept for presentation at the Arizona Meeting any papers received later than July 1, 1916.

Jan 3, 1916

The next meeting of the Institute, the 113th meeting, will he held in Arizona in the latter part of September, 1916. All papers to be presented at this meeting must be published in the September Bulletin or previously. Manuscripts must, therefore, be in the hands of the Secretary of the Institute not later than July 1. In case manuscripts are given by authors to members of technical committees, or others, they must be in the hands of such persons sufficiently in advance so that they may be actually in the hands of the Secretary of the Institute by the date mentioned. In the past, the Secretary has received urgent requests for special consideration regarding manuscripts that come in after the closing date. In view of the obvious unfairness of this, the Committee on Papers and Publications has instructed the Secretary not to accept for presentation at the Arizona Meeting any papers received later than July 1, 1916.

Jan 4, 1916

By Walter W. Fisher, Samuel Rudy

Secondary treated sewage effluent was substituted for normal process water in laboratory tests simulating froth flotation recovery of copper and molybdenum sulfides. Sewage effluent caused significant detrimental response in the flotation process. First, a voluminous, uncontrollable froth was generated, even in the absence of a frothing agent, that has little mineral carrying ability. Second, sewage effluent caused a small loss in copper recovery and a large loss in molybdenum recovery. The detrimental effects of sewage effluent on flotation were partially overcome by tertiary treatment of the effluent by activated carbon adsorption and anion exchange. The frothing problem was significantly reduced after treating the sewage effluent by foam fractionation. Dilution of the effluent with normal process water resulted in a significant improvement in metal recovery. In addition, the large loss in molybdenum recovery was overcome by using a secondary collector in a combination reagent schedule. However, the secondary collector caused an appreciable loss in copper recovery.

Jan 1, 1979

By M. W. Cox, V. F. Hollister

Exploration for metallic mineral deposits is carried on by those special adaptations of methods which the explorer believes will yield most economically or satisfactorily the particular answer sought. In this project the usual methods of geologic observation, recording, and interpretation, when combined with magnetic geophysical methods and geochemical soil sampling, led to disclosures of appreciable zinc mineralization where none was visible in surface exposure. Since 1945 considerable work has been done with geochemical prospecting methods, chiefly in determining the presence and distribution of various elements existing in minor amounts in rocks, soil, vegetation or waters of mineralized areas. Such work, in which the U. S. Geological Survey has taken the lead, finds a ready place in the field repertoire of the exploration geologist as a supplement, not a substitute, for other methods. The Chollet project was carried out in 1951 by the American Smelting & Refining Co. near its Van Stone mine in northern Stevens County, Wash., in the area shown in Fig. 1

Oct 1, 1955

By Howard Smith

FOR several years this Institute has recorded in its TRANSACTIONS the various discoveries of potash? in America, and the successive stages in the development of an independent domestic potash industry. This paper is intended primarily to continue the record through the year 1935. In retrospect it is not inappropriate to note that public interest aroused in 1910 resulted in the production of some 1090 tons of pure potash in 1915, as a small beginning in the domestic inorganic potash industry, and that the infant industry thus begun reaches its majority this year, following a record production in 1935 of about 600,000 tons of potash salts and exports to no less than 22 foreign countries, including six countries in Europe. This production, with an estimated 200,000 tons of pure potash, may be compared with a production in 1934 of 430,157 tons with an equivalent of 144,342 tons of pure potash.

Jan 1, 1936

Total U.S. mineral production reached an estimated $17.8 billion for 1960, 4 pct above 1959 and second only to the record high of $18.1 billion established in 1957. As a group, metals achieved a rise from $1.6 billion in 1959 to $2.0 billion this year, an increase of 28 pct. Similarly the value of nonmetallic production including fuels (i.e., natural gas, petroleum, natural-gas liquids, asphalt and related bitumens, carbon dioxide. anthracite. bituminous and lignite coal, peat, and helium) rose from $15.5 billion in 1959 to approximately $15.8 billion in 1960. However, this 2 pct increase in the total value of non-metallic production was due to an increase in the value of the fuels ($11.8 billion in 1959 to $12.2 billion in 1960) which offset a drop in value of the other nonmetallic minerals ($3.7 billion in 1959 to $3.6 billion in 1960).

Jan 2, 1961

By AIME AIME

FELIX E. WORMSER was born in Santa Barbara on Oct. 31,1894, so is one of the youngest members of the Board, only H. D. Wilde t 39) and W. M. Peirce (43) being his juniors. After graduating from the Columbia School of Mines as an E.M. in 1912, he went West and worked for the Snake River Mines, the Baker Mines Co., and the Cornucopia Mines CO., all in Oregon. Then for a year or two he was the youngest U. S. Mineral Surveyor in Oregon. In 1918 he was in the Army from which he was honorably discharged as a Second Lieutenant. Early in 1919 he joined the staff of the Bureau of Mines, at Washington, assisting in compiling reports and in War Minerals Relief work. His acquaintance there with J. E. Spurr led to his joining the staff of the Engineering and Mining Journal as assistant editor in April, 1920. He specialized in market studies and assisted in the compilation of the Journal's metal quotations until June, 1925, when he resigned to engage in active mining examination and consulting' work in the Northwest for H. H. Armstead. Three years later he returned to New York at the time of the formation of the Lead Indus- tries Association, becoming its Secretary and Treasurer, a position that he has since held.

Jan 1, 1940

Pennsylvania has been a leader in the pageant of industrial America because of her natural mineral re- sources, geographical location, and the ingenuity and industry of her citizens. Brick and other clay products were manufactured in Philadelphia in William Penn's time. Ores of iron, zinc, lead, and copper were mined and smelted in eastern Pennsylvania long before the Revolution. Coal was mined on a commercial basis in the anthracite region as early as 1820 and in the bituminous fields in 1830. The first canals and railroads were constructed to transport minerals and mineral products. Oil was struck at Titusville in 1859. A significant event occurred in 1855-the establishment of the Farmers' High School-Pennsylvania's first attempt to provide higher education for its youth. The Farmers' High School included instruction in geology, mineralogy, and assaying. In 1859 the laws of Pennsylvania transferred to the School the state geological and mineralogical collections formerly located in Harrisburg. Well-informed people are familiar with the effects of the Land-Grant Act of 1862. With inspiring words it established state institutions of higher learning where "the leading object shall be, without excluding other scientific and classical studies . . . to teach such branches of learning as are related to agriculture and the mechanic arts . . . in order to promote the liberal and practical education of the industrial classes in the sev-

Jan 1, 1950

By A. E. J. Engel

The New York talc deposits of commercial importance are in St. Lawrence and Lewis counties, in the northwest Adirondack Mountains (Fig 1). All of the deposits are of pre-Cambrian age and occur within highly deformed and recrystallized marble of the Gren-ville series. The deposits in St. Lawrence County, near Gouverneur, are the largest and most productive of their type known in the Western Hemisphere. In 1948 the seven mines which are in operation will produce about 130,000 tons of ground talc. All talc production in Lewis County is from one mine. There the annual production ranges from 15,000 to 30,000 tons. These so called talcs of New Yorb State include earth materials of different chemical and mineral compositions. In general the mineral talc is subordinate in amount to other minerals in both the Gouverneur and Natural Bridge deposits. In the Gouverneur district the mineral talc comprises less than 25 pct of the mined and ground rock. Most of the rock mined is a tremolite- or tremolite-anthophyllite schist somewhat altered to serpentine and talc. This characteristic in no way tlevaluates the "talc" for certain markets, and in some instances makes the material more desirable. The Natural Bridge talcs include types high in serpentine, as well as complex aggregates of serpentine, talc, carbonates, and diopside. Usage of the term talc, however, for

Jan 1, 1950

When Ponce de León landed in Florida in 1573 he was told of an Indian chief that possessed much gold. In 1576 Diego Meruelo obtained some of it from the Indians, and in 1579 Álvarez de Pineda reported that the natives wore ornaments of gold, which they obtained from the rivers. These statements all refer to the southern Appalachian region. The name is recorded in 1527; when Pamphilo Narváez landed at Tampa he heard that there was much gold to be obtained in a region named Apalache. * In 1564 René Laudonnière describes the methods used by the natives to win gold in the Apalatcy mountains.† However, no serious mining operations were undertaken until long afterward; the mining of gold in the Southern States may be said to have had its beginning when a nugget was found at the Reed mine, in North Carolina, in 1799. This nugget, which was of "the size of a small smoothing iron", was kept for several years before the finder learned what it was, but later more lumps, one weighing 28 pounds, were found in the same locality, and eager digging ensued. ‡ Thomas Jefferson, in his `Notes on Virginia', mentions the finding of a quartz specimen, not a nugget as is generally stated, that contained 17 pennyweights of gold; this was found on the Rappahannock river in 1782. §

Jan 1, 1932

EUROPE continued to be unsettled, financially, commercially and socially. October opened with Germany in a state of turmoil following the Government's cessation of passive resistance to the French and Belgians. In many places there were riots with much bloodshed. In Bavaria a military dictator-ship was set up in order to keep peace. In the meanwhile France continued in an uncom-promising position.. Great Britain, having been diplo-matically discredited, disappeared from any prominence in the international picture. Under the constraint of circumstances the policy of deflation in Great. Britain was temporarily abandoned. Perhaps no other course was open, for with declining trade and heavily reduced revenue, and no chance for cutting expenses propor-tionately, a check to deflation comes of its own accord. The effects of this should become manifest in the course of a few months and should appear in the form of an improved margin between the prices for commodities and the wage costs in producing them. About Oct. 20 an effort was made to set up the Rheinland as a separate republic. On Oct. 26 were published communications from Lord Curzon to Secre-tary Hughes and the latter's reply. In these Lord Curzon drew attention to the gravity of the situation in Europe and expressed the hope that France might listen to renewed suggestions for a general inquiry. Secretary Hughes promised American cooperation, in this, with the reservation that the question of inter-national debts should not enter into the situation. In the latter part of October there were military mutinies and disorders in Greece, which resulted in the reestablishment of martial law by order of Col. Plas-tiras, who is virtually the dictator of Greece. The incipient revolt was promptly crushed.

Jan 10, 1923

By C. E. Arnold

A BRIEF description of this installation was included in a recent paper by H. Kenyon Burch.1 The purpose of the present paper is to amplify Mr. Burch's description, as it is felt by the writer that the subject merits more than passing attention. In making a comparison between the common method of hoisting men in mine shafts, and elevator practice in high buildings, the former shows to great disadvantage both as regards safety measures and smoothness of operation. It is surprising that in view of the inducements offered, the step of applying the building equipment direct to the mine shaft has not been taken before, as in many respects the conditions of service are similar, and the objects to be attained are identical. Even without doing this, it is certain that safety to life and limb in the usual method of hoisting men underground can be greatly enhanced by the application to the mine hoist, of some of the features of the building elevator. In the case under consideration, the elevator cage runs in a vertical, concrete-lined shaft compartment 5 ft. 11 in. by 5 ft. 6 in. (1.8 by 1.68:m.) in section and 585 ft. (178 m.) deep, while the counterweight runs in the pipe and ladder compartment of a twin shaft 102 ft. (31 m.) distant. The section of the division of this compartment occupied by the counterweight measures 2 ft. 4 ¼ , in. by 3 ft. 10 ½ in. (0.72 by 1.18 m.), and the counterweight is made in the form of a small cage which. suffices to carry two men for the purpose of making inspections or repairs in the pipe and ladder way.

Jan 12, 1917

By J. A. Holmes

As the Appalachian mountains reach their maximum development in western North Carolina, we find also in that region indications of extensive dynamic disturbances and alterations undergone by the rocks in' connection with these mountain uplifts. Among the minor results of these changes have been the formation of numerous dikes or a veins " of exceedingly coarse granitic materials, which in some places are mined for the mica which they contain, and in other places are quarried for kaolin. These dikes are filled with quartz, feldspar, and mica, in varying proportions, very coarsely crystallized. Sometimes the mica (generally muscovite), sometimes the feldspar (generally albite or orthoclase) predominates. When the mica is present in considerable quantity, and in large crystals, the dike is usually spoken of as a mica-vein, and is often worked for mica. Sometimes these crystals of mica occur on one side or the other; sometimes on both sides; and sometimes they are largely concentrated toward the middle of the vein, or, it may be, distributed throughout the dike with a considerable degree of uniformity. In many cases the crystals of mica are too small and few to permit the working of the vein as a micamine ; in other cases, very little mica is present, and the feldspar constitutes the larger part of the material. This feldspar of the dikes undergoes, through the weathering action of the atmosphere, certain chemical changes, resulting in its alteration from feldspar into kaolinite—the kaolin of commerce. These dikes vary considerably in size, ranging from a few inches to several hundred feet in thickness, and up to many hundred yards in length. They are generally parallel to the schistosity of the crystalline rocks, which, however, in some cases, they cross at varying angles. The kaolin in those dikes which occur in the Unaka or

Jan 1, 1896

By Charles MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now "potash" has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks.

Jan 2, 1915

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By H. H. Lowry

Science attracts the attention and interest of an individual or an industry in general only in proportion to the apparent direct application to its immediate welfare or benefit. Engineering accomplishments, as aphlied science, therefore receive more recognition than the scientific discoveries on which they are based. Even self-evident truth needs endless repetition before recognition: engineering as applied science cannot advance beyond the science on which it is founded. Scientific research, and discovery, is sometimes forced by the limitations recognized by those active in its development for the use of society and industry and sometimes results from an apparently superficially illogical curiosity about natural phenomena. Research has received inadequate support except in industries born in the laboratory, the chemical and electrical industries, from which many lessons might well be drawn by their elder associates. The rapid growth of these industries has been largely due to close cooperation of scientists and engineers. Most rapid advance is made when the research worker and the engineer keep in close touch with each other's ideas and problems. Many of the developments of modern industry are based on discoveries buried for years in scientific journals because the "time was not ripe" at their discovery. The situation with regard to utilization of coal is quite the oppositre. The fundamental facts in regard to the scientific aspects of the problem of developing the energy from coal are scarcely known. The engineer, without much scientific cooperation, has accomplished much in increasing the number of kilowatt-hours per pound of coal from 0.31 in 1919 to 0.69 in 1934, in increasing the 1000 gross ton-miles of freight hauled from 12.2 to 16.4 per ton of coal in the same period, in fuel economy in production of coke, and in developing the production of motor fuel in Germany and England by hydrogenation of coal. This lack of scientific research on the utilization of our most important natural resource, coal, has been due undoubtedly in large part to the reluctance of investigators to study the interrelationships involved in the complicated processes in which coal is used. These complexities are made

Jan 1, 1936

By M. L. Requa

IN the fall of 1910, the Nevada Petroleum Co., operating in the Coalinga field in California, determined to drill a number of wells with rotary tools, in order to prove conclusively the relative value of the rotary as compared with the standard rig. At that time, the rotary was but little known in California and its proposed introduction met with considerable criticism on the part of the operators and quiet opposition among the standard drilling crews. There were few men available who were competent to handle a rotary outfit, and these few had had but little experience in California fields. Machines as then built were much inferior to those now used, being lighter in construction and of a poorer quality of material. The shells encountered at depths between 1,700 and 2,000 ft. seemed to be too hard to permit of successful drilling, and at these depths the rig was changed over to standard tools and by them completed. Because of the heavy depreciation, the time lost in converting from rotary to standard, and the comparatively small profit, it was concluded that unless in the future there was some material improvement in rotary rigs, nothing would be gained by drilling with rotary tools upon this property. Little or no drilling has been done upon the property since that time, but in the meantime a large number of men have been trained in the use of the rotary; in fact, many standard-tool men have abandoned standard drilling and, starting in as roustabouts, have become thoroughly competent rotary operators. The improvements in the machinery have been such as to remove many of the objections and the rotary drilling of to-day is in every way superior to that of 1910. In contrast, a well drilled recently by the Kern Trading & Oil Co., in the east side Coalinga field may be cited. The first 2,500 ft. was drilled in 24 days and it is confidently expected that the water string will be set with a rotary at 3,400 ft.-a record obviously far beyond that made in 1910 by the Nevada Petroleum Co.

Jan 2, 1915

By Cadwallader Jr. Evans

THE Hudson Coal Co. is an anthracite concern with 22 mines, employing, when operating full, something around 18,000 men. We have, there-fore, necessity for a large number of subordinate officials and for a considerable number of major officials, and we carry on two separate courses of training in our endeavor to develop these two groups. The one in which college professors will be most interested is that which we call our two-year course. A man to be eligible for it must have completed a college course at one of several institutions from which we regularly seek our men, but he need not necessarily be a graduate of the course in mining, although we have been giving prefer-ence to graduates of schools of mines. Each year we take a number of men from these col-leges, sometimes five, six or seven, and put them through this two-year course, which is carefully. laid out so as to give them experience in the various details of our business. A schedule of the typical two-year course laid out for a man who started in July, 1925 shows that he was employed in the mining engineering department first for a period of four months, then for six months in inside mine work, three months in the mechanical and electrical departments, two months in "preparation," which with us means the cleaning of our product for market, one month in the study of statistics, one month on transportation and safety, and seven months in loading coal at the face, working with a shovel, making twenty-four months in all. We started this training in 1915 and in the first year we gave six months in the mining engineering depart-ment. We have now cut that to four. We gave six months in inside mine work and have continued that. We gave four months in the mechanical department, which is now cut to three; five months in preparation, now cut to two; two months in statistics, now cut to one; one month on transportation and safety which re-mains, and we have added seven months in loading coal. This last class of work gives them experience with the miner at the mining face.

Jan 7, 1928