Search Documents

By Norman L. Wimmler, H. G. Iverson, S. Ricker, P. E. Oscarson, S. H. Lorain

THIS paper has been prepared with the principal objective of recording the results of the Bureau of Mines exploration of five major clay deposits in the Western Region. It is based mainly on data contained in unpublished Bureau of Mines reports. Acknowledgment is made to the Federal Geological Survey for its cooperative work with the Bureau of Mines, to the various State geological and mining departments, and other State and local agencies. CLAY EXPLORATION BY THE BUREAU OF MINES Much has been written and published on clays and clay deposits relating to their refractory, ceramic, and other qualities but such literature is lacking in analyses of the available alumina content of the clays and provides little indication of their possibilities as a source of alumina. With this new objective in view, a great many of the known clay deposits were reexamined and new ones discovered. The Bureau of Mines made preliminary examination of numerous areas in the western United States. Five of those most favorably indicated were systematically drilled, and in each a large amount of high-alumina clay has been found. These five major projects are Molalla and Hobart Butte, in western Oregon; Cowlitz-Castle Rock, in southwestern Washington; Lone, in California; and the Olson-Troy area in Idaho (Fig. I). Preliminary scout drilling was done in the Stockton deposit at Coeur d'Alene, Idaho; the Whiteware deposit near Lewistown, Mont.; and 13 areas in the Spokane or eastern Washington region, where the most favorably indicated area, known as the Excelsior, is now being drilled more systematically. Preliminary drilling was undertaken in numerous areas adjacent to the major deposits and others more remote. As a result, large additional clay possibilities were found. THE CLAY DEPOSITS The clay deposits under consideration are of the sedimentary or transported types, parts of which have been altered further by the agencies of weathering, ground water, or hydrothermal action. There are extensive deposits of residual clays in northern Idaho and in eastern Washington, but they have been found to be low in the available alumina and to contain much free quartz, mica, and unaltered feldspar. To be of value, they must first be subjected to beneficiation to remove these gangue minerals. The sedimentary clays have been derived largely from the decomposition, erosion, and transportation of granites, gneisses, schists, and basalts. At Molalla, some

Jan 1, 1944

By S. M. Moos, R. E. Dugger

In reviewing available vacuum filtration equipment in this paper, several types of filters have been included which are probably not familiar to operators in the mining industry. However, it was felt that these units might be of interest in the event that an application should arise for the filtration of a product in the future that does not exist today. In addition, exposure of our industry to equipment used in other industries might have a tendency to be thought provoking and perhaps lead to the development of equipment and/or applications in our industry which do not necessarily exist at this time. Most innovations in filtration equipment have been confined to the improvement or design change of components and accessories, particularly reflecting the availability of materials of construction that have been developed. Recent developments in the application of horizontal belt filters have been innovative. The application of this unit as a substitute for or an adjunct to thickeners in a CCD circuit can certainly be innovative and perhaps provide a basis for reduction in capital and operating costs in this area. For example, mill tails are generally pumped at the highest possible density that will adequately flow. Tailings ponds and dams with their attendant design requirements are based upon this estimated water volume. Availability of a much dryer, non-flowing filter cake opens up several new options for disposal. Considerable cost savings could result in the design and planning of disposal areas for containing dryer material. No attempt has been made in this paper to provide a manual for the operation of all of the many types of equipment that are available. Rather, the paper tries to present an overview. Fundamentals of Vacuum Filtration Filtration may be defined as the separation of solids from a liquid effected by passing the liquids through a porous medium. If the filtrate is induced to flow through the medium by hydrostatic head, we refer to it as gravity filtration. If we utilize super-atmospheric pressure upstream of the medium we call it pressure filtration and if sub-atmospheric pressure is applied downstream of the medium we call it vacuum filtration. Centrifugal filtration occurs when a centrifugal force is applied across the medium. Centrifuges will not be discussed in this paper. The process goal of filtration may be the production of dry solids where the cake is the valuable product, clarified liquid

Jan 1, 1980

By James B. Austin

Growth of the Society When the Institute was born in May, 1871, it was given the name American Institute of Mining Engineers. Yet from its conception a few months earlier, its genetic code clearly carried the message that metallurgy was equal in importance to mining. Thus, the "call" for the initial meeting, which was sent out in April of that year by three mining engineers, Eckley B. Coxe, R. P. Rothwell and Martin Coryell, gave this first objective of the proposed organization as: "the more economic production of the useful minerals and metals." And this call concluded: "Anyone who may have devoted himself to a particular subject connected with either mining or metallurgy, and who may be possessed of new facts in reference to it, would greatly aid in furthering the objects of the proposed association by preparing a paper giving the results of his experience." In response to this call, a group of 22 men assembled in Wilkes-Barre, Pa., for a 3-day meeting beginning May 16, 1871. On the first day, a set of 20 "Rules" was adopted, of which Number 8 read, in part: "The words mining engineers in these rules comprehend engineers connected with mining and metallurgy." On the second day, 18 officers were elected, of whom nine were not present. Moreover, as if to emphasize that the words about metallurgists were to be taken seriously, one of those elected in absentia was the president, David Thomas, a Welshman who had founded the Thomas Iron Co. and who built the first anthracite-fired, hot-blast furnace in this country. The second meeting of the Institute, held in Bethlehem, Pa., in August, had a more metallurgical flavor, and the third meeting, in November, was held in what was then one of the great steel-making centers of the country - Troy, N. Y. This was the home of the Albany and Rensselaer Iron and Steel Co., which held the American rights to Bessemer7s machinery patents. And it was here that the great American steel master, Alexander L. Holley, carried out a series of experiments that led to improvements in the design and method of operation of the Bessemer vessels. It was at this meeting that Holley and Henry Marion Howe, then a "student" at the Albany and Rensselaer plant, were admitted to membership. Four years later, Holley was elected president of the Institute. Clearly, metallurgy

Jan 1, 1971

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsa¬tions. The stratification usually is effected in a rectangular open¬top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (91) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through %-in. to 0, and mixed sizes of ores down to %3 O-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 percent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although con¬siderable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tenta¬tive conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way.

Jan 1, 1943

By Edward L. Clark, Garrett A. Muilenburg

THE first record of the discovery of iron ore in Missouri was Marquette's observation in 1673 of brown iron ore, or limonite, in the Mississippi River bluffs just north of the mouth of Apple Creek in southeastern Perry County. There is no record of any attempt to mine or smelt Missouri iron ores until 1815, when the Ashebran furnace was erected at the Stouts Creek shut-in near Arcadia, Iron County. Some limonite was treated in this furnace, the first iron furnace west of Ohio, but most of the ore was hematite from Shepherd Mountain and adjacent deposits. Eight years later, in 1823, the Perry furnace five miles north of Caledonia, Washington County, was constructed to smelt limonite ore. It

Jan 1, 1955

By John P. Weir

Coal's participation in the domestic energy market depends to a very large extent upon the cost of coal delivered to consumers. Today the principal use of coal in the U.S. is in steam-electric generating stations. Generally, it is the delivered cost per million Btu's that is given the greatest weight in choosing either oil, natural gas or coal as the fuel used in these power plants. There are three major cost components of generating electric energy in steam-electric plants. These expenses expressed in terms of "dollars per kilowatt year" are: (1) operation and maintenance of necessary facilities, (2) fixed charges of necessary capital investment, and (3) fuel. For a modern large plant, the first two items would be approximately as follows:

Jan 9, 1962

By W. Lawrence Austin

At the Troy meeting of the Institute, in October, 1883, I presented a paper entitled "Smelting Notes from Chihuahua, Mexico,"" in which was briefly described a cupellation-hearth, commonly met with in the northern part of Mexico, called in the vernacular un vaso. Since writing the paper I have had occasion to construct a hearth of this description for myself, using it, in conjunction with a waterjacket, for the reduction of a very refractory ore in the form of concentrates ; and I now avail myself of this opportunity to qualify some of the statements made in the paper referred to. At the same time I wish to present some sketches which will enable anyone to run up a similar furnace within three days, should occasion demand

Jan 1, 1885

By Karl F. Peterson, H. K. Najarian, Robert E. Lund

PRIMARY products of the Josephtown smelter are zinc metal of various grades, lead-free zinc oxide pigments, cadmium metal, and sulphuric acid. Zinc concentrates of domestic and foreign origin are blended and desulphurized at the roaster plant. The equipment includes five, 12-hearth Herreshoff roasters and two modified Trail-type suspension roasters. The sulphur dioxide containing gases from the roasting operation are diverted to a four-unit contact acid plant for the manufacture of sulphuric acid. The roasted calcines are agglomerated by sintering on Dwight-Lloyd-type sintering machines; the sinter is crushed and sized within required limits; and the sized sinter is smelted in vertical shaft-type electro-thermic furnaces. Of the 13 electrothermic furnaces of various sizes now in operation, four are designed to produce American process zinc oxidc of various specifications; and the remaining nine furnaces are equipped with vacuum-type condensers and produce zinc metal. Papers describing the general smelting practice at Josephtown have been published by AIME. Since both High Grade zinc metal and lead-free zinc oxide pigments are produced direct from the electrothermic furnaces without need for subsequent refining, the elimination of impurities such as lead and cadmium has to be accomplished during roasting and sintering operations. To effect the producing of both High Grade and Prime Western zinc products, the roasting and sintering operations are on two separate circuits. A High Grade circuit produces finished sized sinter low in lead, cadmium, etc., for the High Grade furnaces; and the Prime Western circuit produces finished sinter destined for the furnaces producing Prime Western metal. Sintering at the Josephtown smelter differs in many important respects from the sintering practice in smelters operating horizontal retort zinc furnaces. Requirements of the electrothermic smelting furnaces define the physical characteristics of the sinter, while the chemical composition of the sinter is controlled according to the grade of metal and oxide to be made as final products. Three principal objectives in the sintering process at Josephtown smelter are: 1. To transform the zinc calcine from the roasting operations into a hard, yet porous agglomerate that will not crumble in the smelting furnace. 2. Crushing and sizing of the sinter to obtain a proper screen analysis which is normally —% in. down to +1/4 in. particle size. 3. To eliminate, particularly in the High Grade circuit, as much of the impurities such as sulphur, lead, and cadmium as possible. The sintering plant as originally built in 1930 was equipped with three standard 42 in. x 44 ft Dwight-Lloyd sintering machines. Each machine was equipped with a 15x60 in. sintering corporation fan driven by 150 hp, 900 rpm synchronous motor through a magnetic clutch and capable of delivering 30,000 cfm of air at 15 in. of water and 150°F. Each sintering machine was driven by 7½ hp dc motor with controllers for varying the speed of the machine from 8 to 32 in. per min. The pallets were cast iron and the grates of the herringbone type. The charge was mixed in a 4 ft diam x 8 ft Stehli pugmill and transported by belt conveyor, elevator and tripper conveyor to a small bin over each machine. Shortly after the start of operations the following changes were found necessary: 1. The herringbone grates which plugged very quickly and were difficult to keep clean were replaced by straight, narrow cast-iron grate bars running at right angles to the travel of the pallets. These grate bars are held in place by a center bar extending across the pallet on the 24 in. dimension and by removable retaining plates which form the sides of the pallets. 2. Mechanical grate knockers were developed in conjunction with new grate bars for continuously and automatically cleaning the grates. 3. As the cast-iron pallets cracked, they were replaced with cast-steel pallets. In 1938, the capacity of the sinter plant was increased with the installation of two 42 in. x 22 ft machines which were brought from the company's Herculaneum lead smelter. With a circulating load of some 250 to 300 pct, production of finished sinter on the 42 in. x 44 ft machines at this time amounted to about three tons of sized sinter per machine hour. In 1945, one of the 42 in. x 22 ft machines was replaced by a 60 in. x 44 ft machine of our own design. In 1948, as part of the plant-wide expansion program, the sinter plant not only was expanded but also divided into two separate plants; namely, Prime Western and High Grade circuits. The sinter destined for furnaces producing Prime Western zinc metal is made in a new plant comprising two 60 in. x 44 ft Dwight-Lloyd-type sintering machines, each having a 45,000 cfm Sturtevant fan at 18 in. water static pressure and served by an 8 ft diam x 12 ft long rotary charge pclletizer and auxiliary crushing and sizing equipment. The sinter destined for furnaces producing High Grade zinc metal and zinc oxide pigments is produced in the old sinter plant which was expanded to accommodate four of the 60 in. x 44 ft sintering machines, replacing the old sintering units. In the High Grade sinter circuit, two units of the 60 in. x 44 ft machines are used as preliminary soft sinter machines; and the remaining two units of the 60 in. x 44 ft machines are used to make finished hard sinter. Purification Theory Partial elimination of lead and cadmium in the sintering of zinc ores is common knowledge. However, by some manipulation and by taking advantage of the double circuit, it is possible to make zinc sinter which is nearly free of contaminators. Lead

Jan 1, 1952

By John Birkinbine

(Wilkes-Barre Meeting, June, 1911). MODERN advances in practically all lines of industrial development have occurred in such rapid succession, and have been accepted so readily as accomplished facts, that a retrospect surprises us, by showing how comparatively few of the acknowledged factors of improved conditions may be considered as old. While these advances have not been confined to any country, they have been more pronounced in some than in others, and nowhere more so than in the United States, the population of which, having multiplied nearly three-fold between 1870 and 1910, demanded a proportionately greater increase in materials, supplies, and manufactured products. It therefore appears desirable to discuss mainly conditions in the United States, as concrete evidence of industrial progress throughout the world. Looking backward for but three generations, we may trace the introduction and development of canal- and steamboat-navigation; railroad-transportation; artificial illumination beyond that furnished by candles and lard-oil; quick communication by mail, and subsequently by telegraph or telephone; the manufacture of iron, beyond forms of small dimensions; the production and utilization of steel in large quantities; the economic use of mineral fuel, oil and gas, etc. The practical coincidence of the fortieth anniversary and the 100th technical meeting of the American Institute of Mining Engineers, offers temptation to recall and compare the conditions of mining and metallurgy in or about the years 1871 and 1911. A complete resume would cover phenomenal changes in mining-methods and equipment by which the output of individual exploitation has grown from scores to hundreds and even thousands of units in equal time-intervals. Extension of operations in depth and area, demanding machinery of great power

Aug 1, 1911

By L. Stone, H. Margolin

The Ti-C-N and Ti-C-O systems were investigated in the temperature range from 500° to 1400°C and in the composition range up to 2 pct C and 5 pct N or 0. Characteristic isothermal sections at 800°, 900°, 1000°, and 1300°C are presented. The Ti-N-0 system was studied in the temperature range from 900' to 1400°C with alloys containing up to 6 pct total alloying content. Characteristic isothermal sections at 1000° and 140O°C are presented. Melting-point data for all three systems are also included. THIS paper reports on one of a series of investi-gations which have been conducted on the phase diagrams resulting from interstitial alloying with iodide titanium. The other investigations involved delineation of the binary systems with carbon,' nitrogen and boron,h and oxygen. The Ti-0 binary system has also been investigated by Bumps et al.' In varying degrees, each of these interstitial elements has been shown to stabilize the low temperature a modification of titanium1-5 and each forms a face-centered cubic TiX compound (henceforth designated 6). In addition, the Ti-N and Ti-0 systems reveal a low temperature tetragonal phase (6) formed by a peritectoid reaction between a and TiX Experimental Procedure The development of experimental techniques for the study of titanium alloy systems has, to a large extent, become standardized. In this investigation, the equipment and procedures described in detail by Cadoff and Nielsenl have been used. Arc Melting: In general, binary alloys with carbon, nitrogen, and oxygen, prepared in the composition range of interest in this investigation, show negligible composition changes during arc melting. However, the possibility of the formation of some gaseous combination of alloying elements such as CO, CN, or NO during the preparation of these ternary alloys was considered. Calculations showed that the evolution of only 0.05 gram of such a gas would be detectable as a pressure change in the closed system used during preparation of these alloys. Such pressure changes were not observed. Consequently, nominal compositions have been used in plotting the data. The compositions of the materials used in the preparation of the alloys are shown in Table I. After melting for 3 to 5 min at 275 to 350 amp, the alloys were checked for homogeneity by microstruc-tural examination. Alloys containing up to 1 pct C were homogeneous in the presence of less than 3 pct N or 0. At higher alloying contents, some inhomo-geneities in the carbon distribution became evident. Alteration of the melting procedure toward longer times and higher currents did not improve the homogeneity of these alloys. Ti-N-0 alloys were homogeneous in the range to about 3 or 4 pct total alloying addition. Beyond this, almost all of the specimens showed as-cast microstructures consisting only of the phase. Consequently, inhomogene-ities could not be detected by examination of micro-structures. Ten alloys from each of the systems were analyzed for two of the elements present (oxygen being omitted in all cases and titanium being omitted in the Ti-C-N alloys). In all cases the analyses were found not to be sufficiently precise to serve as criteria for the total composition of these alloys. On the basis of phase distribution in heat-treated alloys, however, it appears that carbon is distributed throughout the alloys most uniformly, with oxygen and nitrogen following in that order. Heat Treatment: Specimens for heat treatment were wrapped in titanium sheet before sealing in the argon-filled quartz capsules. Heat-treatment times varied from 100 hr at 800°C to 0.5 hr at 1400 °C. After heat treatment the specimens were quenched by breaking the capsule in water. With the exception of alloys in the low composition region, heat treatment did not have an appreciable effect on the as-cast microstructures. Metallography: Following heat treatment, the specimens were prepared for metallographic examination by grinding on emery paper and electrolytic polishing. For the majority of the specimens a 10-sec etch with Remington "A" agent (25 pct HNO3, 25 pct Hf, and 50 pct glycerin) adequately

Jan 1, 1954

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,' and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.'.' Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett's No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17' There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By R. E. Zinkham

An investigation has been conducted to compare short transverse and longitudinal fatigue and fracture properties in 4.25-in.-thick, high strength aluminum alloy plates. One plate was produced using standard rolling techniques while the other was pre.forged before rolling. Little difference was shown in fatigue strength of longitudinal specimens taken from mid-thickness of the plate. Howeuer, in the short transverse orientation fatigue strengths at 107 cycles were about 25 and 50 pct less, respectively, for the preforged and standard rolled plate. Differences in fatigue strengths were attributed to grain size and shape as well US orientation of constituents. Fatigue crack propagation rates and fracture toughness were compared at three different stress intensity (K) levels, using a constant compliance, double cantilever, wedge-shaped specimen. In a given plate, comparable fatigue crack Propagation rates were observed in the longitudinal (i9W) and short transverse (TW) orientations. Somezuhat gveater rates were observed in the short transzerse (TR) orientation. The preforged plute gave a lower rate for all three directions. Considerable secondary cracking developed, at times, over portions of the fatigue crack in both plates, particularly at the lower stress intensity levels in the short transverse specimens. Micro structure revealed constituent stringers as possible causes of the crack branching. Fracture toughness was considerably less in both plates in the short transuerse orientation. It is concluded that preforging not only improved directional tensile properties but also the fatigue and fracture properties in general. On occasion, aluminum plates have been milled away for hinges or bolted connections and stressed through the thickness or short transverse direction. Little or no information is available concerning fatigue characteristics or fracture toughness in this loading orientation in aluminum plate, or of the effect of fabrication on these properties. It was the intent of this project to examine, develop, and apply a unique specimen that has been advocated by others to study the fatigue characteristics and fracture toughness of two differently fabricated high strength aluminum plates. Linear elastic fracture mechanics criteria may be applied to the specimen so that the fatigue crack propagation rate and fracture toughness data may be of use for design or inspection applications. Fatigue characteristics are generally measured in the longtudinal or long transverse direction, where fairly large specimens such as center notched panels,' are usually employed. Limitations are evident due to plate thickness, however, in the type and size of specimen that may be tested in the short transverse direction without extensions. Therefore, a specimen that is to be loaded in this direction should, for convenience, be compact. The general type of fatigue crack propagation specimens discussed and employed herein meet this requirement. These specimens are commonly called double cantilever beam specimens and lately "crackline-loaded edge-crack specimens".2 They may vary from a slope of zero (parallel-sides) to a wedge shape, the type employed herein. In general for most specimens the stress intensity KI at the tip of a crack is a function of the load, P and crack length, a. Some varieties of the wedge shaped specimen, however, give essentially a constant stress intensity KI over a considerable range of crack length.' This feature can be a valuable asset in fatigue crack propagation experiments because the stress-intensity can be controlled simply by controlling the load without regard to crack length. MATERIAL AND METHODS Material. A standard rolled (light pass reduction) and a ~reforged and rolled (heavy pass reduction) plate of 7179-T651 material were used for the evaluation. The chemistry, processing history and average tensile properties are shown in Table I. Specimen Selection and Preparation. The specimen selected for the generation of fatigue initiation or S-N data was an axial tension type and is shown in Fig. 1. Specimens were taken from mid-thickness in the longitudinal and short transverse directions from both plates. Specimens were polished with 500 grit paper in a direction parallel to the loading axis. For the fatigue crack propagation tests, the specimen shown in Fig. 2 was used. This is similar to a specimen that has been employed by Mostovoy3 for fracture toughness studies on 7075-T6 aluminum alloy. It also fortuitiously agrees quite well with the dimensions of a specimen for which Srawley and Gross2

Jan 1, 1970

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By J. D. Hanawalt, W. H. Gross

Magnesium has long been known as the lightest of our engineering metals. This metal, silvery white in color, has a specific gravity of only 1.74. Aluminum, the next lightest structural metal, is 1 ½ times heavier; zinc is 4 times heavier; iron and steel are 4 ½ times heavier; and copper and nickel are 5 times heavier. Magnesium does not occur in the free state but is very abundant in nature, constituting 2.5 pct of the earth's crust in the form of various ores. It is the third most abundant structural metal, being exceeded only by iron and aluminum. Magnesium is unique, however, in that in the form of magnesium chloride it also exists in the oceans. Sea water is the source most widely used for production in the United States but magnesium is also commercially produced from magnesite, dolomite, and other ores as well as from certain inland brines. The vast quantity of magnesium existing in the waters of the oceans can be visualized when it is realized that the removal of one hundred million tons per year (the approximate annual steel production in the United States) for a million years would reduce the magnesium content of sea water only from 0.13 to 0.12 pct, providing no more magnesium had washed into the sea in the meantime. Not only is magnesium potentially very abundant but it is in addition a very versatile metal and can be shaped and worked by practically all methods known to the art of metal working. It can be cast by sand, die, and the various permanent-mold methods;

Jan 1, 1953

By H. Foster Bain

In the preparation of this series of books it was considered particularly appropriate to include this work. Gunther was one of the younger men who was associated with Colonel Mudd in the finding and development of ore deposits. Supported by Mudd, Gunther undertook a systematic survey of the sources of copper of ancient Europe. This survey resulted in the rediscovery of the deposits now worked by the Cyprus Mines Corporation for which Gunther was, until shortly before his death, the resident manager. In finding and developing these mines, Gunther applied the methods and data embodied in this book and proved their usefulness. It is believed that other young engineers may profit similarly. In presenting a new edition, the form and substance of this work have been preserved and no changes have been made in any direct statement of the original author. Individual illustrations, paragraphs and mine descriptions appearing in the first edition have been omitted in order to permit introduction of new material. The latter has been chosen so as to present a somewhat more balanced picture of the mining industry as it now exists. The new material relates largely to the so-called porphyry coppers, to mines in Canada, Rhodesia, Alaska, and a number in the United States that have become important since the book was first written. The new material was prepared by Mr. Russell C. Fleming, using the best that had been published and items of which he had personal knowledge or had obtained by correspondence with men familiar with the deposit described. Whenever possible the description used has been submitted to the original author for correction. In a number of instances

Jan 1, 1932

THE foundation established by the partners of the late Robert W. Hunt provides for both a medal and a prize. The latter has not been given before this year, and the first award is to C. H. Herty, Jr., for his several papers on the physical chemistry of the open-hearth process.. He is the son of the well known chemist of the same name. He was born at Athens, Ga., on Oct. G 1896, graduated from the University of North Carolina in 1918, and went into war service as foreman of U. S. Chemical Plant No. 4, at Saltsville, Va. In 1919 he went to Massachusetts Institute of Technology, where he was successively instructor, research assistant, and research associate in the School of Chemical En-gineering practice receiving his master's degree in 1921 and his Ph.D. in 1924. He continued his brilliant work on the physical chemistry of the open-hearth process, much of it being done in cooperation with the Bethlehem Steel Co. at its Lackawanna plant, and dealing with the elimination of sulfur. In 1926 he joined the staff of the U. S. Bureau of Mines, in charge of its ferrous metallur-gical work at Pittsburgh, and continues to be active in research work on the physical chemistry and metallurgy of the open-hearth process. His Institute publications are: Some Factors Affecting the Elimination of Sulfur in the Basic Open-hearth Process," "Chemical Equilibrium of Manganese, Carbon and Phosphorus in the Basic Open-hearth Process" and "Desulfurizing Action of Manganese and Iron," and he will present a paper on ?Effect of Temperature on the Solubility of Iron Oxide in Iron" at the annual meeting.

Jan 2, 1928

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) A member, technically educated, with 20 years' practical experience as engineer, assistant superintendent, superintendent, and manager of large mines and mills on construction and operation, also experience in mine examination, is open to engagement. Metallurgist of 18 years' experience in Mexico with large plants is open to engagement. Last position, superintendent of copper smelting works. Best line, copper and lead smelting, but also experienced in mine valuation and ore-treatment investigation work. Speaks Spanish. A member of the Institute and graduate mining engineer with 10 years' experience in the Lake Superior copper district, also practical experience, desires position as superintendent or manager. Member, graduate mining engineer, experienced in mine and mill work, geology and field work, one year in the hydrometallurgy of copper, is open for engagement Aug. 15. A member, at present in the Southwest., desires a position as assistant superintendent or assistant manager with a mining company operating in Washington or Alaska. Experienced assayer and engineer. A member, technical graduate, with nine years' mining experience as assayer, engineer, foreman, manager's assistant, and superintendent of large development and operating mining companies in the United States and Mexico, is open for engagement. A member, technical graduate, 33 years of age, 11 years' experience as chemist, metallurgist and superintendent of lixiviation plant and in charge of construction of cyanide mill, desires position as assistant superintendent or superintendent of mining or milling company in United States or Canada. Young man, technical graduate, two and a half years' experience in chemical laboratory, desires position as chemist.

Jan 9, 1913