Search Documents

By B. Wilhelmi, W. H. Somerton

Simultaneous measurement of pore and elastic properties of socks under a wide range of triaxial stress conditions may be made with equipment and methods developed in this paper. Tests were run on three outcrop sandstones at several confining pressures and axial stresses up to approximately 80 percent of failure stress. The greater reduction in porosities and permeabilities occurred in the hydrostatic loading portion of the stress cycle, but substantial reductions in both properties did occur upon application of deviator (triaxial) stress. Triaxial elastic moduli were calculated from strain gauge measurements. Both Young's moduli and shear moduli were found to increase with increasing confining pressure. Poisson's ratios increased with axial stress but showed no consistent change with confining pressure. Only very general relations were observed between pore and elastic properties. The lesser decrease in porosity and permeability at higher stress values is related to increase in rigidity of rocks at higher stresses. INTRODUCTION Many investigators have studied the effects of hydrostatic stress on the properties and behavior of rocks. A few have studied the effects of triaxial stress fields on individual physical properties of rocks. To our knowledge no one has measured simultaneously pore and elastic properties of rocks under a wide range of triaxial stress conditions. This is the purpose of this work. Rocks exist in the subsurface under what Jaegerl refers to as "polyaxial" stress conditions (all principal stresses unequal). When two of the three principal stresses are equal, this is referred to as triaxial loading. The triaxial method of loading is most commonly used in modern testing work because experimental difficulties in measuring physical properties of rocks are greatly reduced over polyaxial testing. Although triaxial loading may not reproduce subsurface conditions precisely, subsurface stress conditions are never known precisely anyway. Triaxial testing would seem to be more realistic than testing under hydrostatic loading (all principal stresses equal) for application of results to subsurface problems. The objectives of this work were threefold: (1) to develop methods of measuring simultaneously pore and elastic properties of rocks under triaxial stress conditions, (2) to determine whether changes in these properties are of sufficient magnitude to be considered in subsurface calculations and (3) to attempt to relate changes in pore properties and elastic properties since they will have been measured at the same time under identical loading conditions. REVIEW OF EARLIER WORK PORE PROPERTIES Several investigators have studied the effects of stress on the physical properties of rocks. Fatt and Davis2 showed the reduction of permeability of rock with hydrostatic loading. McLatchie et al.3 and Knutson and Bohor4 related permeability reduction to compessibility of reservoir rock, again under hydrostatic loading. Wble,5 and later Redmond,6 evaluated the effects of applied radial pressure on conductivity, porosity and permeability of sandstones. In this latter work, no axial stress was applied. Dobrynin7 reviewed much of the previous work done . on the effects of overburden pressure on physical properties of rocks. He concluded that changes in physical properties are controlled to a large extent by pore compressibility of the rock. Several sets of curves developed from empirical relations are presented. These curves permit estimation of change of properties with net overburden pressure, knowing the pore compressibility and porosity of the rock. Net overburden pressure is defined as (Pe - 0.85 Pi ) where Pe is the

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By Harry M. Bendler, W. A. Wood

Electron metallography has been applied to the study of the torsional fatigue of polycrystalline OFHC* copper. The development of slip bands, fis- sures, and microcracks has been followed as a function of strain amplitude and number of cycles. Those factors that have been found to be relevant to a geometrical theory of the fatigue process are described. From the point of view of this theory it is important to distinguish between the effects of cycling at large amplitudes and at small amplitudes (true fatigue deformation). EARLY investigations showed metal fatigue cracking is caused by continued reversal of a small plastic strain. Fundamental study of fatigue, therefore, has been largely concerned with the cumulative effects of these plastic reversals on the metal structure. In particular, recent work has shown that the plastic reversals produce slip movements that are finer than the slip movements produced by unidirectional increments of plastic strain; individual slip movements in fatigue, for instance, are too fine to see by optical microscopy.2 It has also been shown that the fine slip movements of fatigue tend to concentrate in bands and that in this way they can build up, after enough cycles, a progressive surface disturbance. It is this disturbance which, in effect, makes the slip movement visible. It is also in this disturbance that the first cracks appear to form. From this point of view, therefore, the problem of fatigue becomes one of finding why the fine slip movements should concentrate in bands and why the. bands should finally open into cracks. Thus far, study of the slip bands has been limited to the changes they produce at the surface only. These studies have given interesting results. Ewing and Humfrey3 many years ago showed that the bands in iron could extrude debris. Forsyth found that bands in aluminum alloys could extrude thin tongues of material. Thompson showed that, after lightly dissolving away the surface of copper specimens, some bands persisted as superficial cracks might, and that the life of a specimen under fatigue deformation might be prolonged by dissolving away the surface at intervals. Thus these and related results have suggested that the metal structure in fatigue bands may disintegrate and that this may happen long before obvious cracking. These surface studies, however, have not shown definitely how cracking may begin, for they do not show sufficiently what is happening in depth. However, some advance in this direction has been made recently by a new approach, summarized later, which reveals slip bands and their surface disturbances in section. In the work done thus far, the sections have been studied by optical microscopy only. In the present work they have also been studied by electron microscopy with extended results. This paper also describes some observations on the surface disturbances prior to sectioning. These observations are relevant to a suggested theory of fatigue cracking. REVERSED SLIP MOVEMENTS Slip movements in fatigue deformation must reverse direction in each cycle. The question arises: DO the "backward" and "forward" movements take

Jan 1, 1962

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

The subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small. percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for Io Years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. 1). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, non-metallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, Probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to Ioo mg. per sq. cm. per day, the corrosion rate of high.purity magnesium is 0.15 ± 0.05 mg, per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in inin in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable, In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0,001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. while the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1942

By T. Glen Heslop, Dennis H. Laubscher

INTRODUCTION In all cave mining operations waste is drawn mixed in the ore, hauled, hoisted and milled. This waste usually contains some mineral which partly covers some of the costs of mining and milling it, but it still re- presents a loss of profits as the production rate from the mine is matched to the mill capacity - every tonne of waste milled replaces a tonne of profitable ore. Draw control aims to reduce the amount of waste drawn and to increase the amount of ore recovered. It is also used to regulate the grade of ore flowing to the mill and in block cave blocks to prevent potential stress build- up on the major apexes above grizzly drifts. This paper summarises what has been learnt about draw control in the forty years that cave mining methods have been used in the three largest underground chrysotile asbestos mines in the southern hemisphere. The four mining methods to which draw control has been applied are: a. Block caving. b. Shrinkage with overburden caving. c. Sublevel caving. d. Open stoping. Open stoping has been included because on a number of occasions severe falls from the back and side of these open stopes have occurred. Without full records of where and when ore is blasted, when and how much ore has been drawn from each of the drawpoints, it would be impossible to analyse the migration of ore and fallen waste in the stope. Several problems peculiar to chrysotile asbestos ore bodies affect the practice of draw control. Heterogeneous fragmentation, cavities, side pressures and the interaction of stresses in the caved ore affect the migration of ore under draw. Fibre is normally not developed uniformly throughout the ore bodies, values vary from place to place but there is usually a general decrease upwards and the hangingwall contact is an economic limit. The immediate hangingwall rock frequently looks like the ore body hostrock and is difficult to recognise in a drawpoint, and cannot be used as the marker for stopping draw. During caving or shrinkage, a large proportion of fibre becomes detached from the host rock and re- ports in the fines, which migrate differently to the larger rocks. The fines are not sticky, and flow easily if loose and dry, but compacted, the fibre and rock fines con- solidate the ore. During draw the proportion of fines in the ore varies considerably, as fines either flow relatively freely between the large rocks or become trapped and compacted above large rocks or hangups. This creates a large sampling error in drawpoint grade assessments, whether done visually or by bulk sampling, unless the assessments are done frequently. The method of draw control used is to regulate the draw rate in an attempt to lower the ore-waste interface as evenly as possible, and to finally stop working the drawpoint when a calculated tonnage has been drawn.

Jan 1, 1981

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By Frank Harwood Riddle

Products made from the ores of the sillimanite group, and synthetic substitutes for them, have unique properties, and service tests prove that they are playing, and will continue to play, a major part in improvements in metallurgical processes. Also, they are examples of how comparatively useless, rare, or "museum" minerals have been made available in commercial quantities. Until research developed uses for them, the minerals had been observed only in small, scattered masses, or crystals. Improvements in ceramic processes and compositions have come about very gradually. In the last 10 or 15 years, several outstanding developments have been made. Of greatest interest to the mining and metallurgical engineers are those affecting the composition, necessitating the mining of new minerals, and improvements in ceramic products used in metallurgical processes. Sillimanite and Mullite Sillimanite (Al2O3.SiO2), then known as Fibrolite, according to Dana,' was first reported in 1792. In 1796, cyanite (Al2O3.SiO2) was first described.2 In 1873, Behrens published results of his microscopic study8 of porcelain. He showed that it contained what appeared to be crystals, which dissolved less readily than quartz and glass in hydrofluoric acid. Hussak4 described the presence of needlelike crystals as occurring in some instances in small amounts in certain porcelains. In 1908, Plenske and Zoellner both studied porcelain structure.5 Plenske observed that "sillimanite" might be present in masses of exceedingly minute grains which apparently were amorphous. Zoellner advanced the theory that the needlelike crystals were formed by a molecular change in the clay,

Jan 1, 1932

By Hermann Wedding

It is now fourteen years since we German ironmasters, in considerable number, visited the United States on the occasion of the Philadelphia Exposition, and found the iron metallurgy of this country, as must be frankly confessed, in an advanced stage of development not previously suspected by us. At that time the United States already occupied, as now, the second rank, with Germany in the third, the product of pig-iron for that year being, in Great Britain, 6550, in this country, 2093, and in Germany, 1850 kilotons.* This relative position has not been changed. The present annual product of the three countries is, in round numbers, Great Britain, 8380, the United States, 7790, and Germany, 4530 kilotons. But the proportion of the United States, which was, in 1876, but 15 per cent. of the world's product, has now advanced to 30 per cent. When we left America in 1876, it was not only with gratitude for cordial hospitality and for the liberality with which our professional colleagues here had opened to our inspection whatever was worthy of notice in our special field, but also with the conviction that we had collected a great treasure of new and interesting information which we could utilize for the benefit of our German Fatherland. Particularly the achievements of the never-to-be-forgotten Holley in the field of Bessemer practice, set us an inspiring example for imitation in our own country. As an expression of our thanks in more practical fashion, I attempt in this paper to sketch what we have done in Germany since

Jan 1, 1891

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a 'pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By A. W. Jenike

A theory of gravity flow of bulk solids like ores, concentrates, coal is outlined and an example of design for unobstructed flow is given. Mass-flow and plug-flow patterns are defined and related to the geometry of the bin. The effect of these patterns on segregation, first in-first out flow, and caking is described. This paper is a report on the results from the AIME sponsored project "Flow of Bulk Solids" which was carried out under the author's direction at the Utah Engineering Experiment Station, University of Utah, during the period 1956-1962. The theory has been applied to the design of numerous industrial storage plants. A QUANTITATIVE METHOD OF DESIGN FOR FLOW There is hardly an industry which does not store and handle solid materials in bulk form. When the volume of the solids is large, gravity is invariably relied upon to cause the solids to flow out of storage, through channels and chemical reactors. Such materials as ore, coal, cement, flour, plastics, clay, soil, to which a general term of bulk solids is applied, flow by gravity or are expected to flow by gravity in thousands of installations and by billions of tons annually. The chemical and process industry depends on gravity flow of solids in process and out of storage. Mining relies on gravity flow in block-caving, in ore passes, as well as in storage and loading bins. Agriculture uses gravity flow in elevators, in feed plants, and in farm silos. In practice, satisfactory gravity flow is seldom attained. Such problems as doming, piping (rat-holing), lack of live capacity, segregation, deterioration in storage, harass industry. In spite of the universality of these problems, until recently, there has been no theory of solids flow, no method of predicting how a solid would behave, and how the channel, bin, or hopper should be designed. In the late nineteen forties and early fifties, the theory of plasticity came of age and simultaneously the computer became widely available. These two factors permitted the development of a theory of flow of bulk solids. The work was conducted during the years 1953-1961. In conjunction with the development of the theory a method to measure the flowability of solids was also developed1-7 and the theory was ap-plied to the design of ore pockets, storage plants,16 chemical reactors and adsorption columns. A comprehensive report of this work is given in a previous work." THEORY OF FLOW The most important question which a theory of flow has to answer is: what conditions need to be satisfied for a given solid to flow uniformly and without obstructions through a channel? First of all, the following observations are made:

Jan 1, 1967

By F. L. Fayers, J. W. Sheldon

It has been a matter of concern to the petroleum industry to determine what effect the capillary term has on saturation profiles, since these profiles determine ultimate economic oil recovery. In their original solution of the non-capillary two-phase flow problem, Buckley and Leverett&apos; showed that solutions of the two-phase flow equations became multiple-valued in saturation. Since it is physically unrealistic for saturation to have more than one value at a given position, Buckley and Leverett resolved this difficulty by introducing a saturation discontinuity or "shock". They evaluated the strength and position of the shock from material balance considerations. Recently Sheldon, Zondek and Cardwell&apos; have demonstrated that the method of characteristics can be used to solve this and related problems. Owing to capillarity it is physically unlikely that saturation shocks occur in an oil reservoir. Buckley and Leverett suggested that the effects of interfacial tensions should be included in the fluid flow equations, if the solutions are to give continuous single-valued saturation distributions. An analogy to this problem is encountered in the theory of wpersonic compressible flow where the introduction of the viscous term eliminates shock behavior. However, the mathematical form of the capillary term in the porous medium fluid flow equations differs from the viscosity term in the Navier-Stokes equation. This paper demons~rates that capillarity does eliminate the triple-valued behavior and indicates the magnitude of capillary and gravity effects on the saturation profile for a variety of systems. DERIVATION OF LAGRANGIAN AND EULERIAN FORMS OF THE DISPLACEMENT EQUATION The equations representing capillary, two-phase flow are given by applying Darcy&apos;s law and a material balance condition for each phase. The familiar Darcy and material balance equations are as follows. ^U*^0......<3, ^^r=°......c« S is the saturation of the water phase, and B the inclination of the porous medium. Pressures in the oil and water phases differ by the capillary pressure associated with the interfacial tensions, P.-P.=pAS)..........(5) where p, is determined experimentally. The porous medium is said to be oil-wet if P, > Po and water-wet if P, < Po. If the fluids are incompressible and the total volumetric flow rate, q, is constant, then v, f v,, = q...........(6) By eliminating P.. /»,, and v, from Eqs. 1, 2, 5 and 6 it follows that It is convenient to normalize the variables in the problem after the manner of Handy and Hadley% so that Eqs. 3 and 7 become where j,, = —, the fractional flow of water; (F, is a capillary pressure normalizing constant.) Substitution of Eq. 9 into Eq. 8 gives In this partial differential equation for an initial value

By John L. Ham, Robert M. Parke

The melting point of molybdenum is 2625° + 50°C. Heretofore the metal has been considered too refractory to be melted in commercial quantities; hence, it has been formed into rod, wire, and sheet by the methods of powder metallurgy, wherein the temperatures do not exceed 90 per cent of the melting temperature. The manipulation of liquid metals at temperatures of about 2000°C. and above presents some difficult problems in heat transfer, in purification, and in container materials. For metals melting at such high temperatures, it is generally regarded as expedient to circumvent the more common melting and casting process by resorting to powder metallurgy. This circumvention is not accomplished without some penalties, the more notable of which are the relatively high cost of the powder metallurgy method and particularly the size limitations of its product. In an effort to overcome the inherent disadvantages of the powder metallurgy method, especially in respect to the limit of size, a project was begun in 1943 at the Climax Molybdenum Co. laboratory to develop a method of melting and casting molybdenum capable of producing larger bodies of molybdenum than were then obtainable. Later, from Feb. I, 1944, to Aug. 31, 1945, the project was under the supervision of the National Research Committee, Division One. In peacetime, too, there are needs for molybdenurn, which make consideration of another process desirable; for example, large parts for heat engines generally, the omnipresent demand for metal of higher quality and lower cost, and the development of molybdenum-base alloys. This paper describes methods for melting and casting molybdenum, with details of the special process needed to make molybdenum castings ductile, and reports some of the properties of what may be regarded as a new, or at least modified, form of the metal. First Process for Melting and Casting Molybdenum The maintenance of a temperature greater than 2625°C. in a &apos;pace large enough to melt several pounds of molybdenum may involve the loss of heat at a Very considerable rate. For melting molybdenum, therefore, the source of heat must be of high potential and of fairly high power. Evidently, also, the source of heat must not impair the purity of the product. The electric arc operating in vacuum appeared to meet these requirements and was accordingly the first choice as a source of energy. A number of arc devices for melting molybdenum were examined, and several were tried. In the first experiment, a 20-kw., 60-cycle-per-second alternating-current arc was operated between two horizontal and opposed electrodes of molybdenum- In this arrangement the falling droplets of molybdenum solidified below the arc in an irregular mass. This experiment did not produce a useful casting, but the data obtained indicated that

Jan 1, 1947

By Arthur B. Yates

DIAMOND drilling has advanced and expanded during the past few years. Along with this increase there has been a marked trend to rely more and more upon drilling for the outlining of ore for reserve purposes. This is especially true underground, where men have not been available for opening up ore by crosscuts, drifts and raises. During the recent heavy call upon known ore reserves, more drilling has been done for exploration and it has become expedient to drill longer lateral holes from underground and deeper holes both from surface and from exploration headings in the mines. Furthermore, these deeper holes have to be drilled closely enough to warrant calculation of "probable" if not "proven" ore, from the results obtained therefrom. Interpretation of diamond-drill results has become more precise and reliable with the growing knowledge and understanding of the geologic structures that control the geometry of ore distribution, and this has broadened the field of usefulness of the drill. All of this has created a necessity and a demand for more accurate control of the hole as to direction, a more precise and reliable method of surveying for position, and a need for better and more complete core recovery, as well as larger cores, to provide an adequate sample. At depth the control becomes more difficult and, at the same time, more important. CONTROL A close study of drilling in various parts of the world for a period of more than 20 years has brought to light one definite rule, practically invariable; namely, that diamond-drill holes tend to deviate into a position normal to any structure existing in the rocks, such as bedding, schistosity, gneissosity, or even parting or jointing-even if the hole is started at almost any angle other than parallel with the structure. It also appears that the better developed the structure is, the more quickly will the hole get into a position perpendicular to it. It has often been said that there is a tendency for holes to "drift" in the direction of rotation. This is obviously untrue, for in a vertical hole the measure of deviation would depend upon the azimuth chosen as zero, and there is an infinite number of choices. It has been proved, however, that in homogeneous rocks there is a tendency for the hole to corkscrew, and that the direction of the spiral is the same as the direction of rotation. This may account for the belief that holes drift in that direction. Some tests have been made using right-hand and left-hand rods, and these show that no matter what the direction of rotation the hole will swing into a position perpendicular to the structure. Methods of Control The foregoing empirical rule may be used as an indirect method of control. If the prevailing structure is known, it may be advantageous to start the hole as nearly normal to it as possible, for the nearer the direction of the hole is to this ideal, the straighter it will remain. This, of course, is not always practical and in some cases is impossible. Usually such a

Jan 1, 1946

By W. R. Bull, J. R. Roos

A method is described whereby the true financial value of each constituent of each concentrate can be calculated. Each value is then compared with what this value would be in a perfect separation. The difference in each case represents the loss incurred by each aspect of an inefficient separation. The relative magnitudes of these losses indicate those avenues of plant investigation and research that offer the highest potential reward. The metallurgical efficiency of a concentration operation is difficult to express because there are two criteria of performance, namely, grade and recovery. Neither of these alone gives any indication of the effectiveness of an operation and, if they are combined in some formula, it must be empirical and unreliable because of many external factors. Since milling is an operation performed as one step in the most profitable overall method of producing a metal or other end product, the main objective of mill operation should be to make a maximum contribution to this maximum profit. When concentrates are sold to custom smelters, the income from the operation, and the costs, may be calculated. When concentrates are further processed by another division of the same company, and there is no formal financial relationship between, say, the milling and smelting divisions of the company, the mill superintendent&apos;s job is less well defined. But even so, if the mill superintendent works as though he were selling his concentrates, and uses reasonable, if fictitious, conditions of sale, then he can get a good indication of the effectiveness of his operation by calculating his "Economic Recovery". ECONOMIC RECOVERY This is a method used as a basis of operation by several mills and has been described in the literature. Very briefly, the "standard" of operation is taken as that of a mill separating the ore into perfectly pure concentrates with 100% recovery of each mineral in its respective concentrate. For example, a 4%Pb, 4% Zn ore (galena and sphalerite), would provide a lead concentrate weighing 4.62% of the feed and assaying 86.6% Pb and a zinc concentrate weighing 5.97% of the feed and assaying 67.1 % zinc. These perfect concentrates are (hypothetically) shipped to the appropriate smelters, freight and treatment charges and payments calculated, and the net return obtained. This is the optimum financial return for the operation of the mill and is used as the standard. Now the return for the actual, real-life, mill operation is calculated in the same way, and the ratio of the two is termed the Economic Recovery. Many additions and modifications may be made in any particular case. For example, if the zinc mineral is marmatite, the optimum grade of the zinc concentrate may be set lower than 67.1%. If silver is present, it will be recovered 100% in the lead concentrate in the perfect operation. Similarly, cadmium will be recovered 100% with the sphalerite. Mr. Weiss&apos; paper&apos; mentions a case where, because of extremely fine intergrowth between the valuable mineral, chalcocite, and pyrite, the optimum grade of copper concentrate was taken as 45% Cu instead of the theoretical 80%. Each operation will present its own possibilities in this way.

Jan 1, 1970

By A. C. Stoddard

Early in the present century, prospect-ing was active in the area of the present Miami district. There were plenty of blue and green copper outcroppings, but very little ore of a grade that would stand shipping costs had been uncovered. Late in the first decade of the century, tunnels were driven into the north and south slopes of the Inspiration ridge, and two of them exposed disseminated copper sulphide ore. This was the original discovery of such ore on the ground of what eventually became the Inspiration Division of the consolidated company. By 1910 exploration of the ground area was well along and by 1911 underground development had been started. In the next few years a large tonnage of disseminated copper ore had been proven— sufficient to justify the expenditure of several million dollars in mine development and for mine equipment plus large sums for treatment plants. The mine and treatment plants were placed in production July 1, 1915. To Jan. I, 1945, there had been produced from the mines of the Inspiration Consoli-dated Copper Co., more than 106,000,000 tons of ore. Nearly all of this tonnage had been recovered by block caving. GeologIcal and EconomIc FActors Block caving is a mining system based on the fact that if a mass of rock has a sufficient number of fractures and planes of weakness the mass will disintegrate if the support of an area of sufficient size is taken away—that is, "undercut." If the material that caves away from the bottom of a block is drawn off the spalling is progressive. There is a limit to the speed of this spalling or caving action, which varies with the structure of the rock being caved. If the rock is drawn at a rate faster than the caving rate, and if this drawing is continued too long, a void may be created that could make a very dangerous condition if the area should drop as a block and force the air below the uncaved rock out through the raises and drifts. This can be a very destructive force. On the other hand, if the broken material is not drawn fast enough the swell of the material in place to broken material would pack the mass until it was almost solid again and could not be drawn without much blasting, or perhaps even partially undercutting again. Geologically therefore it would seem that any rock with seams and fractures would cave; but for block caving there should be enough seams and fractures in a limited area so that such an area will cave and produce a product that can be drawn safely, rapidly enough and at a cost justified by the value of the product being drawn. At the Inspiration the disseminated ores occur in two formations, the Pinal schist and the Schultze granite. There is no material difference in the grade of the ore formed in the schist and in the granite. The chief copper minerals are chalcocite, malachite, azurite and chrysocolla. Other copper minerals occur in limited quantity.

Jan 1, 1946

By W. N. Hiatt

The mathematical theory of the flow of two-phase, incompressible fluid through porous media is clarified, and the development of a general fluid displacement equation for two-phase, incompressible vertical flow through porous media is outlined. The relationship between the three components of the equation — the "fluid drive effect", the "gravity effect", and the "capillary effect&apos;&apos; — is discussed, as well as implications of the analysis in connection with the study of certain types of petroleum reservoirs. INTRODUCTION The purpose of this paper is to clarify and summarize the mathematical basis of the theory of two-phase incompressible fluid flow through porous media, particularly as it pertains to vertical flow, and to present a qualitative* exposition of the controlling factors involved in circumstances where this type of flow may exist. Although the generally accepted theory of heterogeneous fluid flow through porous media was developed a number of years ago by Muskat,1 and Buckley and Leverett2, 3 using the basic premise of Darcy, (and since then expounded upon by many others) there is a need for an over-all summary and clarification of this theory, especially regarding certain types of applications in connection with so-called "gravity-drainage-type reservoirs". The source and derivation is outlined for what is referred to here as the "General Fluid Displacement Equation for Incompressible Vertical Two-Phase Flow through Porous Media&apos;&apos;. This equation would apply under the condition where the pressure drop along the path of flow is negligible in comparison with the pressure level on the system, or where compressibility and solubility effects are negligible. These conditions exist ordinarily in gravity-drainage-type reservoirs. Specifically, it will be shown that this general equation may be developed directly from the basic equations, which, according to present theory, govern the general case of viscous heterogeneous flow through porous media. This general equation has appeared in the literature previously, but in most cases its development from basic theory is not indicated clearly, or the equation is presented in terms of groups of constants and variables involving reduced or dimensionless quantities. This presentation is expedient in cases of experimental or computer applications; but it may make it difficult for the practicing petroleum engineer to identify all the factors involved or to understand the relationships between them. Therefore, in the following development, only ordinary mathematical parlance will be used, and no terms involving groups of other equations or reduced or dimensionless quantities will be used. DERIVATION The following equations for two-phase oil and gas flow result from analogy with Muskat&apos;s general equations,** if solubility and compressibility effects are neglected, and if all volumes are considered in terms of reservoir conditions, and the water phase, if present, is considered to be immobile (or effectively a part of the porous medium.) In this case, the sum of the oil and gas saturations may be taken as unity, and the saturation of each phase is in terms of the total hydrocarbon saturation. Note that in Eqs. 1 and 2, and in the derivation following, z is taken as positive in the vertically downward direction,

Jan 1, 1969

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K&apos;s) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.&apos; In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By Earle C. Smith

The Chairman.—Mr. Earle Smith has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. Smith,* Cleveland, Ohio—I will start this Off by a story oF the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "we don&apos;t make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don&apos;t dare publish the information. So if 1 collect it and hide it you can&apos;t charge me with having done anything that really disrupted the commercial situation." So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "academic " matter as far as I am concerned. I am in a situation like that of the German who was told in 1956 about the coming war. He said: "until it is your throat that is going to be cut, you don&apos;t pay any attention to what is happening to the otherman." &apos;That is the way with the problem that we have in front of us. Recently I have been told that the &apos;Omptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were nut within the compositions that were included in the specification, and therefore he as the camptroller had no alternative. It was not meeting the specification; therefore, no payment. So I I say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative , chemists who analyze some of these products or lawyers who read specifications, I don&apos;t know which man is going to be the major factor in the future. if the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for That they expect to be umpire eel. the writers would certainly realize that some of the to to which we have calmly signed our names as being O.K. are— well, as one man said to me, they might be filled by the devil, and they certainly could be filled by the Lord, but they could not he me by mankind. I would like to inject two or three things into a segregation study which I Want you to think about, because 1 would be a little surprised if there is very much discussion of them, In the first place, we generslly make steel in the United States in the basic open hearth, and I do not think there has bee,, nearly enough consideration given to segregation German the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0,60 per cent silicon have more respect than they had previously for the segregation that is within, the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another pint to which I think We ought to sis serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregat. ing iron oxide, Normally we are segregating some form of carbon or sulphur, or something like that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1945