Search Documents

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By H. W. Gudenau, R. S. Chatty, W. Wenzel, M. Ponthenkandath

During several experimental programs conducted at the Institute of Ferrous Metallurgy, Technical University, Aachen, whisker formation was observed when iron ores were reduced at low as well as at high temperatures. Thus, in an attempt to find the reason for the volume change taking place during reduction, iron whisker growth was observed. Whisker growth appears to be one of the important reasons for the swelling of pellets. One set of experimental observations determined that when iron forms as needles rather than as a crust on the surface of oxide, the pellets became very porous. In related experiments, the beneficiation of finely disseminated iron ores, in which the metallic iron is separated from the gangue in granular or nodular form, was achieved by a reduction-concentration method. In this process, which is conducted at sufficiently high temperatures, oxide whisker growth, resulting from the formation of volatile suboxides and a gas transport mechanism, plays a vital role in the joint deposition of SiO, and iron from the vapor stage.

Jan 1, 1973

By F. P. Dewey

Recent discussions have furnished to the members of the Institute much information concerning aluminum and its applications. The present paper will be devoted almost entirely to the description of a process by which the metal is produced in the form of alloys. The characters which especially distinguish the Heroult process consist in electrolyzing a mass of molten alumina (Al2O3), and at the same time alloying the separated aluminum with a heavy metal, the heat necessary for the fusion of both the alumina and the alloying metal being supplied by the direct passage through the molten Al2 0, of an electric current of high amperage and low voltage. The process has been in active operation at Neuhausen in Switzerland for about two years. It is also in active operation at Froges in southern France. Both these locations were selected for this purpose on account of the presence of large and desirable water-powers. The apparatus consists of a carbon containing-vessel, which may be a single crucible for small operations, or may be built up of slabs or blocks of carbon for large and industrial operations. When built up of slabs or blocks, the whole is surrounded by an iron casing. In the earlier crucibles this iron casing was cast around the carbon, in order to secure close electrical contact. This, however, has been found unnecessary; and in the later crucibles the casings consist of plates bolted together, while pulverized carbon is packed between the carbon blocks and the iron. Electric conductors are united direct to this iron casing, and the current passes from this through the carbon lining to the interior of the crucible. By this

Jan 1, 1890

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

W. E. Ewers (Commonwealth Scientific and Industrial Research organization, Melbourne, Australia)— Any attempt to elucidate further the meaning of the contact angle, particularly if it deals with the magnitudes of those mysterious quantities rsa and YRL, is certain to receive attention from those interested in the fundamentals of flotation. It is imperative, therefore, that attention should be drawn to a serious defect in the treatment by de Bruyn, Overbeek, and Schuhmann. Their Eq. 5 dy = — ld/u — Th2odiH2n states correctly the relationship between the change in surface free energy dy, the surface excesses Tx and Th2o of the components x and H2O and the changes du, and dph2o in the chemical potentials of these components. This equation applies for constant pressure and con- stant temperature and for the interface of the solid in contact with the solution of X. The relation remains valid when 1.1 is defined so that TH2O becomes zero and the equation becomes dr = — r:dur [17] From this equation de Bruyn et al. correctly concluded that increased adsorption of the collector at the liquid solid interface would reduce the interfacial energy ysl. Their second conclusion, however, that an increase in the contact angle, corresponding to a greater decrease in rsa than in rsL can be attributed to greater adsorption of X at the solid-air interface than at the solid-liquid interface is quite unjustified. The portion of the solid surface from which the collector solution has been displaced by air must be considered in terms of the equilibria between the gaseous phase and the surface. If the pressure and temperature

Jan 1, 1955

By W. R. Atkins

THE Negaunee mine is at the east end of the Marquette Range, in the city of Negaunee, on the Upper Peninsula of Michigan. Iron ore was first discovered on this property in 1883 by diamond drilling. A shaft was sunk soon afterward, and the mine has been worked continuously ever since. The total shipments from 1887 to' Jan. 1, 1945, were 20,417,587 long tons. The mine was taken over by the present operators, The Cleveland-Cliffs Iron Co., in 1903. During the past four years, 1941 to 1944 inclusive, the property has produced an average of nearly a million tons a year, and has employed more than 400 men. GEOLOGY The ore body at the Negaunee mine lies in a large syncline dipping about 15° to the west, the ore coming to ledge at the east end of the trough. The ore occurs in the Negaunee formation of the middle Huronian age, which consists of ferruginous cherts and slates through which intrusions of diorite have occurred. Although these intrusions of diorite have an important bearing on the formation of ore on the range, they are not important in this ore body. Some faulting has taken place along the diorite intrusions, or dikes as they are called locally, and also other faults are known to exist across the formation. These faults do not complicate either mining or development of the ore body. The footwall consists of jasper underlain with Siamo slate; the hanging wall is jasper and ferruginous chert. Fig. I shows a typical cross section of the ore body. The ore body is quite regular, about 120 ft. thick in the middle of the syncline and thinning out toward both sides of the fold. Its width ranges from 400 to 800 ft., the average being about 600 ft. The footwall is uniform in dip and strike, but irregular lenses of ore often extend 50 to 75 ft. up into the overlying jasper capping. METHOD OF MINING Ore in the Negaunee mine has been mined by top slicing almost exclusively since 1903. This method of mining has been employed because it is especially adapted to the size and shape of the Negaunee ore body, and to the soft, sticky nature of the ore as well as the generally soft, broken jasper capping. Development The ore body has been developed from six different levels with intervals varying between l00 and 125 ft. On the average, the dip causes a horizontal offset of 350 ft. per level, and under these circumstances it has been necessary to carry on considerable development in rock to make available the ore lying along the north and east footwalls. This is not as disadvantageous as might be supposed, because of reduced pressure and the accompanying saving in maintenance costs. The development of the

Jan 1, 1946

By Hsun Hu

Based on Kurdjumoiv-Sachs orientation relationship for the fee bee transformation in metals, the jirzal crystal orientation resulting from successive transformations of bee-fee-bee has been analyzed mathematically. There are 528 different variants; many of ther are crystallograpyically equirvalent. Specific examples show that, for equal probability of all the variants, the principal crystallographic axes [100 ], [110], and [111] of the initial bcc crystal can be transformed into vairous axes in the fina1 crystal However, fur each of these principal crystallographic axes, a continuous range of orientation within certain regions of the unit triangle is completely avoided by the finctl Crystals. For uses of higher indices, the final orientations are more uniformly distributed throughout the unit triangle. Results from the PI-esent analysis are in good agreement with preferred Oientations Observed in a zone-meltecl iron bar. THE allotropic forms of iron are characterized by the unusual fact that at both high and low temperatures a bcc structure is stable, whereas at intermediate temperatures (1400" to 910°C) the metal is fcc. Hence, during cooling from its melting temperature, iron undergoes successive phase transformations ofd—? —a with corresponding changes in the crystal structure of bcc — fcc -bcc. while numerous studies have been made in the past of the 1 — a transformation in iron and in various iron-base alloys, no information is available in the literature as to the mechanism of 6 — l transformation and the lattice orientation relationship between these two phases. Experimental difficulties have apparently prevented researchers from undertaking these studies. The laltice orientation relationship between the parent and the new phases of iron resulting from

Jan 1, 1965

By J. B. Austin

IN considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based . upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these effi-ciencies are more useful than others, yet all are instructive; for a knowl-edge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermo-dynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By P. M. Robinson, M. B. Beaer

The heat of formation at 0°C of the intermetallic compound AgMg as a function of composition has been determined by tin-solution calorimetry. In this technique, the heat of formation is determined as the difference in the heat effects, at infinite dilution, on dissolution of the compound and a mixture of its components added alternately to liquid tin from a reference temperature, such as 0°C. The experimental technique and method of calculation have been described elsewhere.' The compound AgMg is a 0 electron compound with a CsCl structure.2 In nonstoichiometric compositions of the compound, atoms of the excess component are substituted on the AgMg lattice.3,4 The homogeneity range is approximately 43 to 52 at. pct Mg at room temperature and 38 to 65 at. pct Mg at 500Oc.2 Single-phase alloys outside the homogeneity range at room temperature can be prepared by quenching. The specimens used in this investigation contained from 39.0 to 54.8 at. pct Mg. They were made available, together with analyses, by the Research Laboratory of the General Electric Co. Metallographic examination of the quenched specimens containing 39.0 and 54.8 at. pct Mg gave no indication of the presence of a precipitated phase. The measured heats of formation are listed in Table I. In a calorimetric run, four to six additions each of a specimen and the corresponding mixture of the components were made. One or two calorimetric runs were carried out with each composition depending on the amount of samples available. The limits stated in the table represent the experimental precision and not the absolute accuracy of the measurements. Thermodynamic investigations of the compound AgMg have been made by Trzebiatowski and Terpilowski 5 and Kachi.6,7 The heats of formation at 500°C derived from the combined electromotive-force values of these investigators8 are more exothermic than the heats of formation at 0°C reported here, Fig. 1. The differences cannot be explained by the difference in temperature. This is shown by the published heat capacity of the stoichiometric compound, which obeys the Kopp-Neumann rule from 0" to 500oC.9 The heats of formation derived from equilibrium data are generally considered to be less accurate than those determined by calorimetric methods because small errors in the change of the equilibrium values with temperature have a large effect on the calculated value of the heat of formation. The heats of formation derived from the combined published electromotive-force values reach a maximum at 56.0 at. pct Mg.8 Kachi reports a maximum of -4.7 kcal per g-atom at the stoichiometric composition.7 The present results also indicate a maximum at or near the stoichio metric composition, Fig. 1.

Jan 1, 1964

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

By J. H. Frye, J. W. Caum

ONE of the most important methods of increasing the hardness of metals is alloying. In spite of the widespread use of alloys, the fundamental mechanism of alloy hardening is little understood. This is true even of the simplest form of alloy, the primary substitutional solid solution in which solute atoms substitute for solvent atoms at random in the crystal lattice of the latter. A fundamental understanding of the mechanism of solid-solution hardening would be important, both because of the widespread use of alloys of this type and because of the light that might be thrown on the mechanism of hardening in more complicated alloys. The present investigation covers the hardness of primary substitutional solid solutions of zinc, gallium,, germanium; and arsenic in copper. All of these are B subgroup elements from the third period of the periodic table. Cu, Zn, Ga, Ge, and As are in groups I, II, III, IV, and V, respectively and lie just to the right of the transition elements. Because of their cost, it is unlikely that Ga-Cu and Ge-Cu solutions will ever be of commercial importance, but the intent of this study has been to discover some of the fundamentals of solid-solution hardening and it has been demonstrated that such a study is far more likely to be fruitful if alloys are made up on the basis of position of the constituent elements in the periodic table than if commercially important alloys are used. Many investigations have. been made of the hardness of substitutional solid solutions, but lack of attention to purity of the metals, infrequent grain-size control, and the use of varying testing techniques have virtually invalidated any comparisons. The purpose of most investigations has been to solve immediate problems and not to solve the primary problem: Why do solid solutions usually have a greater hardness than pure metals? PREVIOUS WORK Theories have been advanced to account for the hardness of solid solutions,, but relatively little experimental work has been done. Perhaps the first experimental work of merit was that of Norbury1 on copper alloys. He showed that for several alloys there was a correspondence between the hardness of one atomic per cent solutions and atomic volume of the solutions. More recently Brick, Martin, and Angier2 have investigated the effect of various solute elements on the hardness of copper. They concluded that the hardening effect of these solutes depended "primarily on the difference in atomic volume of solute and solvent or, relatedly, upon the parameter, change of the solvent or the extent of solid solubility." They also observed the effect of these elements on hardness and texture developed by rolling and by annealing of rolled material. Austin3 examined the hardness and response to heat-treatment of various iron solid solutions. Frye and Hume-Rothery4 measured the hardness of a number of silver solid solutions containing approximately

Jan 1, 1943

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

By Frank Harris

THE strength of hard drawn copper wire is a question of considerable importance to both manufacturer and consumer. Unlike steel and alloy wires, in which strength is governed by both chemical and physical considerations, the high conductivity required for copper wire in the electrical industry generally precludes the possibility of obtaining tensile strength through the use of alloys. Consequently, this strength is largely a matter of the physical structure, and all factors known to affect this structure, such as rolling temperature, die contours, lubricants, drawing speeds, etc., are matters of prime importance. The experiments described here have been carried out during the past year at the Baltimore plant of the American Smelting & Refining Co., in connection with a general investigation of some of the questions mentioned above, with the object of studying the physical structure of hard drawn copper, wire and the influence of certain factors on that structure. The work has been of an exploratory nature, rather than comprehensive, but it was thought that the results might prove of sufficient general interest to warrant their publication. The bulk of the hard drawn copper wire used in places where strength is an important factor is manufactured to strict specification, based usually in the United States on that of the American Society for Testing Materials (B-1-23). This specification calls for almost as high a value of tensile strength; consistent with elongation, as it is possible practically to obtain, and only physically perfect material can be relied on to meet such a specification. Obvious defects, such as laminations produced through fins in the original rods or brittleness due to overdrawing, are usually recognized and need only passing reference. Laminations can be detected by twisting and untwisting the wire several times; they will show up on the surface in the form of fins. Fig. 1 shows a very bad example of this defect. The wire may be perfectly smooth before twisting but when such laminations are present they will readily show up under this treatment. This trouble is caused by similar defects in the original rod produced by overfills in rolling. Fig. 2 shows the cross-section of the rod from which the wire in Fig.1 was drawn.

Jan 1, 1928

By H. Sevim, T. M. Yegulalp

This paper summarizes recent developments in modeling of underground coal slurry haulage networks to determine optimum design and operating parameters. The model presented is based on a stochastic dynamic program¬ming formulation. It is applicable in any typical room-and-pillar or longwall mining configuration commonly practiced in the US. The formulation and structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1985

By John Lovejoy

As the Seminole area, Seminole and Pottawatomie Counties, Okla., appears to be the chief danger zone of overproduction in the United States, it may be of interest to review the production records of the various pools which make up this area; also to dis-cuss the future prospects of these pools, together with the structurally "high" points which may develop into new pools. It is also of interest to appraise the effect of the curtailment program in this general area, which was agreed to in principle by the various Seminole op-erators at a meeting held on May 23 at the offices of W. C. Teagle in New York. There are four large pools in the greater Seminole area. They are, in the order of their importance Seminole City, Bowlegs, Earlsboro, and Searight pools. A glance at the accompanying general map of the area will show their relative situation. The detail maps show the extent and area of these prolific spots. Seminole production comes from the Wilcox sand of Ordovician age, found at a depth of 3900 to 4300 feet. Semninole City Pool:-This pool was discovered in Wilcox sand in July, 1926. By Jan., 1927, there were 123 wells completed, making 146,000 bbl. per day. The field reached its peak of 253,000 bbl. per day the last week of Feb., 1927, with 211 completions and a per well average of 1200 bbl. On July 4 there were 304 wells completed, producing 102,000 bbl., with a per well aver-age of 336 bbl. per day. This pool will cover an area of approximately 3500 acres. It has produced approxi-mately 38,000,000 bbl. to. July 1. Estimates of total ultimate production are around 55,000,000 bbl. or somewhat better than 15,000 bbl. per acre. Some of the individual leases have already yielded 30,000 and 40,000 bbl. to the acre. Bowlegs Pool:-This pool shows 175 drilling wells and 131 completions making 180,000 bbl. per day, with an average per well production of 1380 bbl. It appears that this pool will develop into nearly as large an area as Seminole City. The wells, however, do not give up

Jan 8, 1927

By K. L. Williamson, P. W. Dugan

INTRODUCTION In recent years there has been increased social awareness and government attention directed toward the mining industry. The growing influence of the Occupational Safety and Health Administration (OSHA), the Mine Safety and Health Administration (MSHA), and the Environmental Protection Agency (EPA) has resulted in volumes of regulations governing a multitude of health and safety aspects of mining and milling. These regulations naturally have had an impact on new plant design and in some cases have necessitated retrofitting of existing plants. This paper will not examine the regulations governing the industry, since they are a matter of public record, but rather will address two specific health considerations, dust and noise, and their influence on the design of crushing and screening plants. DUST AND NOISE CONCEPTS Dust is generally defined as finely divided solids which may become airborne without any physical or chemical change except fracture. Since the purpose of comminution circuits is to reduce the size of solids by fracture, a percentage of the material is normally reduced in size to a point where it can easily become airborne. The major cause of dust becoming airborne is the air induced by falling material. When granular material falls through a distance, the induced (or entrapped) air rushes out available openings, carrying with it the fine particles that have become suspended. For this reason, the major points of dust generation are the points where the material is falling: chutes, transfer points, screens and equipment feed and discharge points. The expected dust concentration in an area is a function of the degree of size reduction (i.e., finer particles are more readily carried by air currents than heavier particles) and the volume of air that is induced. The measured dust concentration values for various operations agree with this

Jan 1, 1982

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low made molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported.

Jan 3, 1978

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1&apos;3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine&apos;s earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine&apos; systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By K. S. Krishnam, A. G. Guy

VOLUME 6 of the Transactions of the Baikov Institute of Metallurgy, Moscow, is devoted to the subject of "the experimental and theoretical study of the physical characteristics of dilute solid solutions,11 and summarizes work that has been done largely in the years 1958-9. In view of the attention that Soviet investigators have given to this subject, it seemed useful to carry out an independent experimental investigation in an effort to judge the scientific basis and practical significance of this field of study. The present note is a preliminary report of this investigation. The first property studied by the Soviet group was X-ray spectra of solid-solution alloys.&apos; An anomaly observed at low concentrations (--0.05 at. pct) of the alloying element led to the theory that each impurity atom in a transition-metal base alloy is the center of a "block" of affected atoms with a radius of about 10"7 cm. This theory was further developed in a later paper.2 By this time similar anomalies had been found in diffusion coefficients3 and in thermal expansion.4 The entire development up to 1959 was reviewed in a comprehensive paper, and further theoretical ideas were also published at this time. Finally, the volume mentioned above was published in 19607 giving new experimental data on anomalies in optical properties and Hall constant, and a new theoretical treatment also appeared.&apos; Although western scientists have done both theoretical work, summarized recently by Friedel,9 and considerable experimental work on dilute solid solutions, there is little support for the marked anomalies reported in the Soviet papers. Of the physical properties studied by the Soviet investigators, thermal expansion was chosen for the present investigation because of the relative ease of obtaining the necessary precision of measurement. A Leitz dilatometer was used for this purpose, and a special technique involving interchanging of the two specimens being compared permitted a precision of 0.05 x X in average thermal expansion over the range 27° to 600°C. The specimens were heated and cooled in vacuum or in a protective atmosphere at a rate of 50 °C per hr. Ferrovac E iron was used as the comparison specimen and in every case had a coefficient of expansion higher than (or equal to) that of the alloy. Since unintentional impurities are an important factor in studies of dilute alloys, special attention was given to the purity of the iron and the alloys used. The alloys were the same of those used by Abrahamson10 and by Michalak," and their preparation is described in these references. Chemical analyses of the Ferrovac E iron and of typical Fe-W and Fe-Mo alloys are given in Table I. The purity of the iron and alloys is undoubtedly higher than in the

Jan 1, 1962

By Valentin R. Garfias

The world&apos;s production of petroleum during 1926 is estimated at 1,096,000,000 bbl., an increase of about 29,000,000 from that of 1925 and somewhat larger than the average during the last 4 years, which is about 1,049,000,000 bbl. The daily average during the year may be estimated at 3,000,000 bbl. of which the United States produced 2,123,000 and other countries 877,000. The outstanding developments during the year have been the decline of the Mexican fields, the counterbalancing of this decline by the increase in Venezuelan and Russian production, and increases in Roumania and Colombia. During 1926 the United States, Mexico and Russia retained their relative positions as the three leading producers, while Venezuela probably outranked Persia for fourth place, Roumania passed Dutch East Indies for sixth, and Colombia moved from sixteenth to the eleventh position. It further appears that should present conditions develop normally throughout 1927, it is not improbable that Mexico will be outranked by Russia as the second oil-producing country and that the increased yield of Colombia will place this country in the eighth or ninth position, and ahead of India. The United States and Mexico should produce in 1926 about 79 per cent. of the world&apos;s total and the aggregate of the seven leading countries should be close to 95 per cent. of the total. It is interesting to note that about 85 per cent. of the total comes from fields on the American continent, the United States accounting for about 71 per cent., and Spanish-American countries and Trinidad for 13 per cent. Production of countries other than the United States and Mexico has gradually increased during the last four years and now represents about 21 per cent. of the total. The United States easily retains its long standing leadership with a total yield of 775,000,000 bbl., or an average daily yield of 2,123,000, representing about 71 per cent. of the total, which is about equal to that of the previous year. An increase in production of about 11,000,000 bbl. is indicated by the statistics so far available. It will be noted that the American production in the last 4 years has averaged about 746,000,000 bbl. yearly and that this uniformity, as well as the marked increases

Jan 1, 1927

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930