Search Documents

By David N. French

In a recent paper, Miyoshi, Hara, and sugimotoL have shown that hardness increases and crack resistance decreases with polishing time in tungsten car-bide-cobalt alloys. They attribute the changes in hardness and crack resistance to cold working in these alloys. More recently Exner2 explains the decrease in crack resistance with the amount of material removed (polishing time) by suggesting that polishing removes a high compressive residual surface stress due to the initial grinding operation. He cites previous work on steel to show grinding can induce surface compressive stresses but offers no direct experimental measurements to support this in cemented tungsten carbides. In recent work we have observed changes in residual stress in the W C phase as measured by X-ray diffraction techniques with changes in polishing conditions.3 As a result of the work of Miyoshi et al.,L a brief study was undertaken to investigate the effects of polishing and grinding on the residual stress in the WC phase and have been reported.4 A single composition of tungsten carbide —10 wt pct Co was used. Two initial conditions were studied: an annealed condition with about -30,000 psi residual stress from the differences in thermal coefficients of expansion of WC and cobalt and, on the same specimen, a surface ground with a 150 grit diamond wheel. Stress was measured in the WC phase using X-ray diffractometry as a function of the amount of material removed by metallographic polishing with 6 diamond paste. The results are shown in Fig. 1. Two things are noted, 1) polishing with 6 p diamond paste has little effect on the annealed sample and 2) the magnitude of the grinding stress is markedly reduced as material is removed. By the time 0.1 mil is removed the surface has a metallographic polish satisfactory for light microscopy examination. Thus the surface, even though polished, can still retain most of the stress due to grinding. Since WC is itself slightly ductile, it seems reasonable that high compressive stresses can be generated in the surface by the plastic deformation accompanying grinding. Exner2 suggests, by analogy with steel, that as a result of grinding both WC and cobalt in the

Jan 1, 1970

By H. Landsberg

The curriculum presented here is an outgrowth of discussions by the Committee on Geophysics Courses of the A.I.M.E. in previous years. It had to be a compromise between the desires voiced by employers of geophysicists, professional geophysicists and the possibilities at an average college. There one has to face the questions of the available teaching staff, the inertia of administrators and teachers set in their ways, and the red tape involved in modernizing antiquated curricula. It is, of course, not ideal to have colleges and universities lag Io years behind the times. Rather, instead of being prodded by industry, they should be ahead of industrial needs. There should also be a certain amount of leeway for the student in any college curriculum. All these points had to be considered in drawing up a curriculum, which, instead of being narrowly termed "geology" or "geophysics" was rather called "earth science." It gives the student a chance to specialize in one of the various branches represented by teachers on the faculty of The Pennsylvania State College, giving as options Geology (with subdivisions of Mineralogy and Paleontology), Geophysics, Geography, and Meteorology. Table iA represents the option of geophysics in the curriculum that envisages that a student may want to make his career in any of the fields encompassed by the American Geophysical Union or in geoexploration. This is, of course, only the start of an education that in most cases will have to be followed by graduate work for complete professional training. The outlined curriculum is definitely of an engineering type and is identical for all of the four options mentioned for the first two years. Specialization will start in the junior year but even thereafter the branches are kept as closely allied as feasible in order to permit a student to change from one tO the other (e.g., because of a different aspect in the mployment situation) with a minimum of additional work. Table IB shows the geophysics option according to subject matter, indicating the considerable amount of work in the fundamentals of mathematics, physics and chemistry with a liberal number of geology courses, and some engineering. The courses in the field of geophysics are limited—just two lecture courses as a general introduction and one field course, to permit the student a visualization of the correlation between mathematically analyzed physical data and the geological realities. Thesis work is considered essential to teach the student, while he is still in college, some things S. F. Kelly has mentioned as desirable: (I) following of instructions for somewhat independent work; (2) organizing of material, and (3) producing a readable report. This, together with the personal contact with the advising faculty member, will help in forming a student's personality. The seminar course attempts to get the student into the habit of reading current literature, so that he can keep abreast of the times.

Jan 1, 1946

By H. Landsberg

The curriculum presented here is an outgrowth of discussions by the Committee on Geophysics Courses of the A.I.M.E. in previous years. It had to be a compromise between the desires voiced by employers of geophysicists, professional geophysicists and the possibilities at an average college. There one has to face the questions of the available teaching staff, the inertia of administrators and teachers set in their ways, and the red tape involved in modernizing antiquated curricula. It is, of course, not ideal to have colleges and universities lag Io years behind the times. Rather, instead of being prodded by industry, they should be ahead of industrial needs. There should also be a certain amount of leeway for the student in any college curriculum. All these points had to be considered in drawing up a curriculum, which, instead of being narrowly termed "geology" or "geophysics" was rather called "earth science." It gives the student a chance to specialize in one of the various branches represented by teachers on the faculty of The Pennsylvania State College, giving as options Geology (with subdivisions of Mineralogy and Paleontology), Geophysics, Geography, and Meteorology. Table iA represents the option of geophysics in the curriculum that envisages that a student may want to make his career in any of the fields encompassed by the American Geophysical Union or in geoexploration. This is, of course, only the start of an education that in most cases will have to be followed by graduate work for complete professional training. The outlined curriculum is definitely of an engineering type and is identical for all of the four options mentioned for the first two years. Specialization will start in the junior year but even thereafter the branches are kept as closely allied as feasible in order to permit a student to change from one tO the other (e.g., because of a different aspect in the mployment situation) with a minimum of additional work. Table IB shows the geophysics option according to subject matter, indicating the considerable amount of work in the fundamentals of mathematics, physics and chemistry with a liberal number of geology courses, and some engineering. The courses in the field of geophysics are limited—just two lecture courses as a general introduction and one field course, to permit the student a visualization of the correlation between mathematically analyzed physical data and the geological realities. Thesis work is considered essential to teach the student, while he is still in college, some things S. F. Kelly has mentioned as desirable: (I) following of instructions for somewhat independent work; (2) organizing of material, and (3) producing a readable report. This, together with the personal contact with the advising faculty member, will help in forming a student's personality. The seminar course attempts to get the student into the habit of reading current literature, so that he can keep abreast of the times.

Jan 1, 1946

By G. P. Marino

The "conductivity ", Kr, of a spherical void in a linear temperature gradient due to radiation is calculated by integration of the general expression for diffuse radiation between two gray surfaces of arbitrary orientation. The spherical geometry allows an exact evaluation of the phenomenon without resorting to up-proximate expressions for the radiant heat flux. The resulting expression for Kr is three quarters of the approximate value obtained by Loeb. IN the determination of the thermal conductivity of porous materials such as sintered UO2 and ThO2 fuel pellets, the magnitude of the thermal conductivity in the pores due to radiative heat transfer across the pore, Kr, may be important in assessing the total conductivity of the pellets. Loeb' has calculated Kr for various pore geometries by approximating the net flux of heat between two surfaces of temperature difference AT as 4eT~AT and obtained: K,=4yoet3odp [1] where a is the Stefan-Boltzmann constant, E is the emissivity of the radiating surface, To is the average absolute temperature of the region across which radiation occurs, dp is the largest dimension of the gap in the direction of heat flow, and y is a geometric factor. That is: y = 1 for laminar pores and cylindrical pores with axes parallel to the heat flow direction, y = 2/3 for spherical pores, y = /4 for cylindrical pores with axes perpendicular to heat flow direction. It was the purpose of this work to obtain an exact expression for K, in spherical pores by integration of the general expression for the net heat transfer between two incremental areas on the surface of a spherical pore. This procedure yields a value of Kr 3/4 of that obtained by Loeb. I) CALCULATION OF Kr Fig. 1 illustrates the general geometry which defines the problem. The total emissive power for a gray body is given by: E = EoT4 [2] where E is the radiated energy per unit area of the radiation surface per unit time, T is the absolute temperature, o is the Stefan-Boltzmann constant (o = 5.67 X lo- '' watt per sq cm-"K1), and E is the emissivity of the surface. Although Eq. [2] gives the exact expression for the total emissive power of any gray body, all practical problems involve the net exchange of thermal radiation between a body and surrounding bodies. The two major considerations in the solution of such problems are a) shape and relative position of the surfaces and b) the emissivities of the surfaces. In this work it shall be assumed that all incremental areas on a pore have the same emissivity and, further, that little or no reflection occurs (i.e., the radiation hitting a surface is either absorbed or transmitted). Thus, the solution of the stated problem requires only that consideration a be satisfied. Consider two incremental surface areas dA 1 and dA2 of the same material in a general orientation to one another. Let dAl be at temperature TI and dAz be at T2. Fig. 2 illustrates the geometrical parameters involved. That is, 71, is the normal of dA, n2 the normal of dA2, r the line connecting the centers of each area, 81 the angle between nl and r, and Q2 the angle between 7,2 and r. Using Eq. [2] and the Lambert cosine law of diffuse radiation it is easily shown that:293 WdAf- dA, = ecr T*------^fpi------" dAidA2 [ 3a 1 and

Jan 1, 1970

By S. J. Rothman, A. L. Harkness, L. T. Lloyd

Self-diffusion in Y uranium has been measured using U235 as the tracer isotope. The diffusion coefficient fits an Arrhenius-type equation D = 2.33 x 10 -3 exp (- 28,5000/RT) cm2/sec The values of Do and Q are unusually low and are not consistent with the values expected from theories based on a simple vacancy mechanism of diffusion. CYLINDRICAL samples, 1 cm in diam and 1/2 to 1 cm long, were prepared from high-purity uranium containing 0.0343 pct u235, Table I. The samples were water quenched from 690°C (the a-ß transformation is at 668°C) to remove preferred orientation, and annealed at 450 "C to minimize residual stresses. One end of each cylinder was polished on a 1-µ diamond lap and electropolished in a phosphoric acid solution. After a final cleaning by cathodic sputtering, a 1- to 3-µ thick layer of the tracer isotope, uranium containing 93 pct u235, was sputtered onto the sample.' To prevent contamination during the diffusion anneal, the diffusion couples were placed in a tantalum cup and covered with another piece of uranium, and the whole assembly was sealed off in an evacuated quartz tube. Annealing temperatures were constant within +2.0°C. The samples were heated and cooled slowly between room temperature and the ß-? transformation (774°C) in order to minimize distortion of the sample surface that might arise from aniso-tropic thermal expansion and density changes during phase transformations. After machining off 1/16 in. from the radius to

Jan 1, 1961

By S. A Weigand, J. W. Bolton

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By J. W. Bolton, S. A. Weigand

Production of sound bronze castings is a matter of great practical interest to users and manufacturers of high-grade non-ferrous engineering specialties. Although there has been much excellent research in this field, there still remains some confusion regarding the fundamental principles underlying production of really sound bronze. The literature of the past 20 years on this subject indicates that the prevailing opinion of metallurgists and foundrymen has been that unsoundness in bronze is due generally to oxidation. The following references are typical. Review of Literature Carpenter and Edwards1 state that when gun metal is melted the alloy dissolves gas, the amount increasing with rise in temperature and duration of the melting. The solubility of the gas diminishes during the fall in temperature and it escapes through the liquid metal. At the moment of incipient solidification there is an evolution of gas. Sperry2 says that by using charcoal a reducing atmosphere is supplied whereby oxidation is prevented, and this also prevents gases from coming in contact with the metal. Logan3 says that many of the troubles that occur in non-ferrous castings are the direct result of one thing—oxidized material. He mentions how readily copper absorbs oxygen when molten, but does not mention the harmful effects of reducing conditions as observed in overpoled copper. Guillemin and Delachana14 investigated the gases occluded in bronze and found that the better bronzes contained mostly hydrogen while the poorer ones had a larger proportion of carbon monoxide and carbon dioxide.

Jan 1, 1929

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939

By John T. Galey

In southwestern Pennsylvania 151 wells1 were completed during 1938, a total of 61 less than the preceding year. Of this number 81 were gas wells and 28 oil wells, which shows a considerable decline from 1937, when 108 gas wells and 64 oil wells were completed. However, 42 dry holes were drilled during 1938, which is two more than the previous year. Shallow Development—Gas No new extensions to old pools, or new wells that would indicate any substantial reserves, mere found during the year. However, a number of commercial wells and many dry holes were drilled to the Big Injun sand in Menallen township, Fayette County. One well had an initial open flow of 6 million cu. ft. In Rich Hill township, Greene County, one well producing, from the Big Injun sand, 2 million cu. ft. was brought in. Several other gas wells were completed in Shaler township, Alleghany County and Center township, Greene County, both of which had initial open flows of 1 million cu. ft. from the 30-ft. sand. Another well, in Aleppo township, Greene County, had an equal volume from the Gordon Stray sand. Oil Development has proceeded at a retarded rate because of the low price of Pennsylvania-grade crude. A total initial of only 205 bbl., an average of 7.3 bbl. per well, was developed. This is 1785 bbl. less than during 1937 and no new repressuring operations have been contemplated to prevent the declining production. The average price received for oil was $1.56 per barrel, with a high of $1.88 and a low of $1.34. This oil costs $1.94 per barrel2 to produce. The average price paid for Bradford

Jan 1, 1939

By Robert C. Mackenzie

EXAMINATION by the differential thermal analysis technique of a large number of samples of soil and other clays from various parts of the world has demonstrated that the occurrence of cold-precipitated hydrated ferric oxide (the identification of which in soil clays has previously been reported5) is not confined to any limited locality; e.g., it has been found in varying amounts in clays from Britain, France, South Africa, and Mexico. The conditions necessary for its formation have not yet been elucidated in spite of the number of samples examined, and, since this mineral is so easily prepared in the laboratory, it has been considered that a study of its constitu¬tion and of the conditions under which it could be prepared might. lead to a better understanding of the factors involved. These experiments form the subject of this short paper, and while they do not supply a definite answer to the mode of formation of this mineral in nature, they may, it is hoped, add something to our knowledge in this direction. EXPERIMENTAL WORK Materials Employed The a-Fe2O3.H2O (goethite) and B-Fe2O3.H2O (Weiser and Milligan") were obtained from the Department of Geology, University of Aberdeen, and Rothamsted Experimental Station, respectively. The beta material had been prepared by the method described by Fernelius.1 y-Fe2O3.H2O (lepidocrocite) was prepared at the Macaulay Institute for Soil Research by the method of van Schuylenborgh.6 The method employed for preparation of the cold-precipitated hydrated ferric oxide* was as follows: 1: 1 NH4OH was added (moderately fast with rapid stirring) to a solution of 5 grams FeC13.6H2O in 250 ml distilled water at room temperature (ca. 15°C) until red litmus turned blue, and then 2 to 3 drops in excess. The resultant precipitate was filtered off on a Buchner funnel and washed free from Cl- with distilled water. Previous experiments having shown that drying over P2O5 at room temperature or drying at 105°C in the oven did not significantly affect the thermogram,5 samples were nor-

Jan 1, 1952

By C. van der Poel

When oil is displaced from a horizontal formation by another fluid of lower density, the latter tends to override the former in the shape of a tongue owing to gravity segregation. This gravity tongue has an adverse influence on the oil recovery. If the fluids are miscible, diffusion (mixing) takes place at the interfacial boundary of the gravity tongue. This mixing should have a favorable effect on oil recovery. The report describes a laboratory study of the magnitude of the mixing zone under various conditions, so as to assess the effect of diffusion on oil recovery both in laboratory experiments and under actual field conditions. The technique used enables visual observation and measurement of the size of the mixing zone in transparent glass-powder packs. The results show that in experiments in small models and cores the width of the mixing zone may well be of the same order of magnitude as the height of the model. In such cases oil recovery is favorably affected by mixing. It can further be concluded that, under conditions prevailing in the field, mixing of the injected fluid with reservoir oil is equal to that caused by molecular diffusion alone, eddy-mixing not taking place to any appreciable extent. A simple calculation, then, shows that molecular diffusion is too small for a beneficial effect to be expected from the injection of miscible fluids in horizontal or nearly horizontal reservoirs unless pay zones are thin. INTRODUCTION This paper gives results of experiments made on the mixing which occurs when a miscible displacement is carried out in a horizontal reservoir. This mixing takes place at the interfacial boundary of the gravity tongue formed when the lighter injected fluid overrides the oil present in the reservoir. The object of the experiments was to simulate the field case where, for example, propane with a viscosity of 0.075 cp under reservoir conditions displaces an oil of viscosity 0.6 cp. In the experiments the lighter fluid had a viscosity of about 1 cp and the heavier one a viscosity of about 8 cp, so as to obtain the same viscosity ratio. In order to enable the results to be compared with those published in the literature, a set of experiments with viscosity ratio equal to one was also performed. EXPERIMENTAL TECHNIQUE The technique developed for the purpose enables the width of the mixing zone to be studied as a function of time and place. A glass-powder pack is saturated with a water-glycerine mixture of suitable viscosity, which represents the reservoir fluid. The pack is then rendered transparent by dissolving sufficient ammonium thiocyanate in the mixture to obtain a solution with a refractive index matching that of the glass powder. Alkaline water to which phenol-phthalein has been added is used as the lighter and less-viscous displacing fluid. In those places where mixing or diffusion of the two liquids occurs, the slightly acidic ammonium-thiocyanate solution neutralizes the alkali in the water, and the glass pack shows up white against the red-colored invading water. If a black cloth is hung over the back of the apparatus, the transparent part of the glass pack appears black. In this way the position of the two phases and the transition zone between them is clearly visible, as shown in Fig. 1 (where the red-colored invading water is the grey-shaded zone lying uppermost). In all experiments the amount of alkali in the water was chosen such that the upper contour corresponded to a concentration of 5 per cent of the dense liquid. The lower contour is determined by the size of the glass grains and the thickness of the pack and, consequently, varies from experiment to experiment. Corresponding concentrations of the dense liquid range from about 97 per cent for packs of small grain size (permeability = 1 darcy) to about 95 per cent for those with large grains

By L. P. Teas

ALTHOUGH 1927 in the Arkansas-Louisiana territory will probably pass into history as a year of small profits and little new production, nevertheless during this period two large gas fields were developed; two new oil fields were discovered, and two new oil horizons, hitherto of minor Annual Production in Millions of Barrels FIG. 1.-PRODUCTION OF NORTH LOUISIANA AND ARKANSAS BY FIELDS FOR 1926 AND 1927. importance, were developed; In spite of the "hard times" some of the leading, supply houses did more business this year in this. district than in any year since 1920.

Jan 1, 1928

By William R. Webster

I have continued the investigation of the Pottstown Iron Com pany's basic Bessemer keel plates on the line referred to in my paper of last October (Trans., xxi., 766)) and have added a study of the hardening effects of sulphur, which were not taken into account at that time. The results are so encouraging that I now give them in full. For some months we have graded all the steel at these works by the table given in my former paper, and checked the grading by the forging-tests as described in the paper of Mr. Joseph Hartshorne, read at the same meeting (Trans., xxi., 748). The steel thus graded was bloomed for the plate orders. Then one slab was rolled into a plate for the order, and a tension-test was made of this plate. By the result of this tension-test we were guided in rolling the balance of the heat. Out of several hundred heats graded in this manner, 95 per cent. met the requirements of the orders in every respect, and were accepted; but these results will no doubt be improved upon, when the influence of sulphur is also considered.. The hardening effect of sulphur seems to be about 500 pounds per each .01 per cent. of increase. In the table accompanying the pres ent paper, the ultimate strength with .06.5 per cent. sulphur agrees with the old table where sulphur was not considered; that is, for all steels with less than .065 per cent. sulphur we now get lower re sults, and for those with more sulphur, higher results. Making this allowance for sulphur, the assumed ultimate strength of a 3/8-inch plate of pure iron is reduced from 38,000 pounds per square inch to 34,750 pounds. With this as a basis, I have constructed my new table, giving each of the elements, carbon, phosphorus and manganese the same hardening effect as before, to wit : Carbon is credited with a constant effect of 800 pounds per each, 0.01 per cent. Phosphorus shows greater effect in high-carbon than in low-carbon steels. For 0.07 and 0.08 C, it has about the same effect as carbon, that is, 800 pounds for each .01 P. This increases to 1500 pounds per .01 P in 0.15 C steel, or nearly twice the effect of carbon. This

Jan 1, 1894

By Neil H. Cole

Cost and price inflation and financial gearing through loans are characteristic of modern resources projects. Conventional discounted cash flow and 1P.R analyses, in real terms, and without financing, have inadequacies which can yield misleading results. The degree of improvement in value for project equity owners is limited to the value of the additional tax benefit accorded through the financing instrument used. Debt financing may be low in price and value, but its priority means that the equity owners assume a higher risk, thereby increasing the cost, or price, of their capital. The cost of equity capital, or investment hurdle rate, is related to the Capital Asset Pricing Model. Distortions do occur, with inflation, due to depreciation effects, which can cause the adoption of misleading project rate of return or hurdle rate criteria. For investment decisions, the greatest accuracy possible in forecasting is essential, especially for inflation rates,

Jan 1, 1985

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

By William E. Bruce

In recent investigation of drilling processes, the U.S. Bureau of Mines measured the operating characteristics of two percussive drills. Basically, this entailed measuring maximum piston velocities while drilling. The maximum piston velocity is not necessarily the same as the striking velocity. The latter is usually somewhat lower1 because most commonly used drills provide an air cushion which slows the piston just before it comes in contact with the drill rod. Penetration rates for the two drills were determined in nine rock types, and the physical properties of the same nine rocks were measured and tabulated. Then the penetration rates were plotted against the individual properties to determine the general relationships on which methods for predicting drilling rates could be based.2

Jan 1, 1970

By William H. Love

ATLAS shaft was sunk to explore at depth a portion of the eastern end of the dry belt, or silver belt, of the Coeur d’Alene mining district. The Atlas mine is a mile east of Mullan and is on the south side of the Osburn fault. Equal partners in the venture are Hecla Mining Co., Newmont Mining Co., New Jersey Zinc Co. and Atlas Mining Co., the financing being equally shared by Hecla, Newmont, and New Jersey Zinc. As outlined the project had as its goal deep exploration of prominent structures developed in the Atlas in upper levels. Plans called for deepening the shaft from the 800 level to the 2400 level with subsequent drifting, crosscutting, and diamond drilling on the 2400.

Jan 11, 1954

By G. W. Crane

When ore was discovered on the Tintic Standard property in the spring of 1916, new developments were immediately started both north and south of that property, on the supposition that in East Tintic the ore would be found to occur in northerly trending channels, similar to those so characteristic of the older camp. But 9 years of developments have failed to establish the existence of such a channel. This is due undoubtedly to important differences in the geology of the two camps, that were not recognized, and is indicative of the danger in the general tendency toward interpreting the geology of East Tintic too strictly in terms of that of the older camp. It should not be forgotten that while the two sections have had practically the same geological history, the net results of a long series of geologic processes have developed in them conditions that differ so widely and in so many particulars that the necessity of regarding them as essentially different districts seems apparent. In an effort to emphasize this fact, this paper is devoted chiefly to a comparison of the geological conditions as found in the two camps and is addressed more particularly to those familiar with the geology of the Tintic district. Following a short description of the several ore discoveries and of the Tintic Standard mine is a brief discussion of the evidence of ore channels in East Tintic. For my information regarding the Tintic Standard mine, I am indebted to the courtesy and generous assistance of Messrs. Wade and Snow of the Tintic Standard Mining Co. East Tintic District The Term East Tintic district is here used to represent that eastern part of the Tintic mining district lying between the productive portion of the old camp of Tintic on the west, the foot hills of Goshen Slope, on the east, the Denver and Rio Grande Railroad on the north, and Silver Pass on the south, all in Utah County. As represented by the geological map, Fig. 1, it includes an area about 4 miles wide, east and west, and 5 miles long, north and south, within which the Tintic Standard mine is about centrally located. The map is a compilation of data supplied, for the most part, by the Chief Consolidated Mining Co. and represents the

Jan 1, 1927

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer&apos;s knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen&apos;s bridge&apos;) was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946