Search Documents

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By C. C. Templeton, J. C. Rodgers

A key step in feed water treatment for generating wet steam for thermal oil recovery is the removal of calcium and magnesiunt hardness by cation-exchange series softening. Knowing the solubility of any scale forming salts in brines at elevated temperatures is necessary for fixing the level to which the feed water must be softened. Such calcium sulfate solubility data, previously not available above 392F, were determined by the authors in a flow equilibrium apparatus mud will be reported elsewhere. These data were used to develop a method for predicting the solubility of anhydrite in hot water or steam droplets for saturated steam pressures as high as 2,000 psig (637F). (The calcium sulfate solubility product is represented by a combination of two factors, one reflecting the effects of ionic strength and the other accounting for the effects of complex ion formation in either calcium-magnesium-rich or sulfate-rich brines.) The method is applied to a calcium-magnesium-rich brine If moderately high salinity from a pilot hot-water flood, I nd to several sulfate-rich, low-salinity feed waters and l lowdown (cooled steam droplets) samples from steam s ak operations. The predicted calcium hardness levels corresponding to the calcium sulfate solubilities agreed reasonably well with the results of laboratory solubility determinations run on the field samples. Further testing of the method is needed for brines of other composition classes. Existing field cation exchange softeners in the cases tested are performing adequately since all the samples were found to be undersaturated with respect to calcium sulfate at their operating temperatures. Introduction Prevention of scaling caused by precipitation of calcium sulfate (anhydrite) is of considerable concern in connection with thermal recovery processes using wet steam or hot water. To avoid anhydrite precipitation in a heated system, an engineer must keep the product of the calcium and sulfate concentrations in the water or steam droplets below the value of the solubility product of anhydrite for the temperature and brine composition in question. Usually it is most practical to keep the concentration product lower than the solubility product by keeping calcium low in the presence of high sulfate, or by keeping sulfate low in the presence of high calcium. This can be done by a choice of combinations of natural waters and water treatment processes (such as series cation exchange softening to remove calcium). Until recently, few anhydrite solubility data, particularly for solutions containing other salts, were available for temperatures above 392F (211 psig steam); Marshall, Slusher and Jones' studied the CaS0,-NaCI-H,O system up to 392F and surveyed the work of previous investigators. To model natural brines, one needs to study the solubility of anhydrite in aqueous solutions of sodium chloride, sodium sulfate, calcium chloride, magnesium chloride and their mixtures. Since steam pressures as high as 2,000 psig (637F) may be involved in thermal oil recovery projects, a solubility study was conducted between 482 and 617F.' Discussed in this paper is the application of these data to the prediction of anhydrite precipitation in some practical steam soak and hot-water injection projects. Any simple method for predicting the solubility of an inorganic compound over a wide range of temperatures and solution compositions must be based on some assumptions, and therefore must yield approximate results. On the one hand, natural brines contain too many ionic species for all to be included in a simple scheme; on the other hand, there is no adequate theoretical basis for the exact prediction of solubility in even simple solutions of mixed electrolytes. However, it is possible at a given temperature to base a reasonable prediction scheme on two phenomena:'-' the increase in solubility with increasing total concentrations of all ions (as measured by the ionic strength; see the Appendix), and an increase due to formation of cornplexes between calcium ions and sulfate ions and between sulfate and magnesium ions. Stiff and Davis' developed such a scheme for predicting the solubility of gypsum (CaSO, ¦ 2H,O) in brines at temperatures u~ to 212F. However, for the higher temperaturei of present interest, the stable solid phase is anhydrite (CaSO,). This study involves a two-part method for predicting anhydrite solubility products. First, one predicts a value K, for a given ionic strength I and a given temperature T corresponding to mo./msr, = 1 from data of the CaS0,-NaCI-H,O system. Second, one determines a group of factors F .= F(Ca) • F(Mg) • F(SO,), where the individual factors account for increases in the solubility product due to complex formation by high concentrations, respectively, of calcium, magnesium and sulfate. Combining the two parts, one obtains the solubility product in molalities as

Jan 1, 1969

By Maurice Ewing, J. A. Peoples, J. W. Peoples, A. P. Craby

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By George S. Koch

We have devised a multivariate statistical model useful to interpret data from exploration geochemistry and also pertinent for the analysis of data from petrology, paleontology, and other geological fields. The model is applied to several simulated cases in order to compare anomaly recognition by inspection and by quadratic regression.

Jan 1, 1977

By C. S. Matthews, J. L. Mahaffey, W. M. Rutherford

This paper gives results of an experimental study of the sweep efficiency of a miscible displacement in a five-spot. The study was carried out in a parallel-plate glass model in which effects of diffusion were scaled at or near the molecular diffusion level. The experiments show that very early breakthrough (25 to 35 per cent of pore volume (PV) injected) may be expected in miscible floods because of the unfavorable viscosity ratio. However after 1 PV of displacing fluid is injected, the sweep rises to a reasonable value (50 to 60 per cent). Photographs show that small slugs of less than 10 per cent of PV tend to dissipate before breakthrough. A minimum slug size of 15 per cent of PV would appear to be necessary even in a relatively homogeneous formation. Presence of a slug whose viscosity is inter-mediate between that of oil and gas increases the sweep efficiency of the oil-gas system. In a typical system the sweep at breakthrough rose from 26 to 37 per cent of PV for a 25 per cent slug. The increase in sweep brought about by use of a large slug could well pay for the extra deferment cost of the additional slug material. INTRODUCTION Most miscible displacement processes involve the displacement of oil with fluids of much lower viscosity and density. The displacement process at these adverse viscosity and density ratios is dominated by instability phenomena, i.e., viscous fingers and gravity tongues. These phenomena have highly adverse effects on oil recovery. Although a number of laboratory studies have been made to determine the effect of adverse viscosity ratios on five-spot sweep patterns,l,2 the scaling of diffusion effects is uncertain. In the series of scaled model studies reported herein, an attempt was made to scale diffusion. Model studies of miscible displacements in which molecular diffusion predominates are per-mitted by controlling the parallel plate spacing which reduces convective mixing to arbitrarily small levels. To decide how this scaling relates to any particular Geld displacement necessitates an estimation of diffusion effects for the natural rock being considered and conditions under which displacement will be conducted. The approach normally taken is to extrapolate data obtained from stable miscible displacements performed in the laboratory, such as those presented by Brigham et al.3 The validity with which such an extrapolation can be applied to an unstable flow system has yet to be established. If this approach is accepted, a family of oil recovery curves can be generated for a single viscosity ratio based on Brigham's observation that the magnitude of the dispersion coefficient is dependent, among other things, upon specific rock properties. Objective of our test was to define the lower limit of this range by presenting the case where dispersion effects were reduced to the molecular diffusion level in both the transverse and longitudinal directions.

Jan 1, 1967

By J. S. Rinehart, W. C. Maurer

The mechanics of impact crater formation in rock, particularly sandstone, has been sutdied, the velocity range being approximately that normally associated with oilwell gun perforators. The bullets were small steel spheres having diameters of 3/16, 9/32 and 7/16 in; impact velocities ranged from 300 to 7,000 ft/sec. The craters have two distinct parts — a cylindrical hole (or burrow) with a diameter the same as that of the impacting sphere, and a wide-angle cup comprising most of the volume of the crater. The burrow is fornred as material in front of the projectile is crushed and pushed aside, forming a cylindrical hole surrounded by a high-density zone. The clip forms as fractures are initiated in front of the projectile and propagate along logarithmic spirals, approximaling maximum shear trajectories, to the free surface of the rock. A most significant observation (made for the first time) was that, below the base of the cup in one type of sandstone, there are a group of similar fractures, not extending to the surface, which are spaced uniformly a few millimeters apart. Each fracture follows roughly the contour of the base of the cup and appears to require a certain threshold impulse to initiate it. These fractures comprise a relatively high fraction of the total, newly exposed surface area. The volume of the material removed by crushing varies as the first power of the impact velocity and the volume removed by fracturing, as the second power of the impact velocity. Penetration varies linearly with the impact velocity and is inversely proportional to the specific acoustic resistance of the target material, the proportionality constant being dependent upon the shape of the projectile. INTRODUCTION Yield of oil from a producing well is frequently enhanced by firing bullets and shaped charges through the well casing into the oil-bearing rock, forming craters and fractures from which oil can flow more readily. The purpose of this investigation has been to develop a better understanding of the mechanics of impact crater formation in rock, particularly sandstone, the velocity range being approximately that normally associated with oilwell gun perforators. FORCES OPERATIVE DURING IMPACT When a projectile moving at considerable velocity strikes a- massive target such as oil-bearing sandstone, intense and complex transient stress situations develop within both the projectile and the rock or sandstone against which it is striking. Usually the struck rock fails, the missile or projectile penetrating into the rock to some depth where it comes to rest or is forcibly ejected from its burrow by expansion of a plug of target material compressed in front of it. When the impact velocity is very high, the projectile itself may fail, breaking apart or becoming distorted; this situation is not considered here, the discussion being limited to nondeforming projectiles. Many experimental studies'.' have been carried out to determine the nature of the mechanics of crater formation and the salient features of the forces coming into play, some of the earliest studies being the French Army experiments performed at Metz between 1835 and 1845.' The stratagem in most instances has been to make a post-mortem examination of the crater, measuring volume and depth of penetration and deducing force relationships from these observations rather than performing the more difficult (usually almost impossible) feat of measuring stresses during penetration. In many materials, the force acting during penetration of the projectile is found to be the sum of two components—(1) a constant force, independent of the velocity, representing some inherent strength of the target material; and (2) a component, proportional to the square of the velocity, representing inertial forces. For such materials, the average force per unit area acting on the projectile at any instant while it is in motion and being decelerated may be written F/A = a + bv2 . . . (1) where v is the velocity of the projectile at that instant, A is the cross-sectional area of the penetrating projectile taken normal to its trajectory, and a and b are constants which are dependent upon the target material and the shape of the projectile. It follows that the total penetration s is given by .........(2) where v, is the velocity of the projectile when it just strikes the target. Values of a and b for spherical projectiles impacting in a loose sand-gravel mixture and compacted earth were obtained in the Metz experiments. For sand-gravel, a and b are 620 psi and 0.0115 (psi) (ft/sec)', respectively; and for compacted earthworks, a and b are 432 psi and 0.0008 (psi) (ft/sec)'. Figs 1 and 2

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

By W. A. Backofen, F. de Kazinczy

FRACTURING under conditions of particular interest is identified with the junction of curves relating tensile yield and fracture stresses to test temperature; the intersection point gives the lowest stress, for brittle fracture (at the ductility transition temperature). An expression for is found in Cottrell's brittle-fracture analysis, Eq. [15],1 while measurements of this stress and temperature have been reported for a low-carbon steel heat treated to differ-

Jan 1, 1962

By M. Takeda, H. Majima

Pyrite has been subjected to xanthate adsorption experiments in order to determine the nature of adsorption. The identification of adsorbed species by means of IR spectroscopy, as well as UV, shows that the dixanthogen adsorption is undoubtedly predominant on pyrite surface. The rest potential measured in a xanthate solution coincides with the redox potential of the xanthate-dixanthogen couple. Considering all the factors together, the adsorption mechanism of dixanthogen on pyrite has been proposed as This mechanism is consistent with the "passive" character of pyrite. From the measurement of the redox potential of the xanthate-dixanthogen couple in the homologous series, a rule similar to that for surface tensions proposed by Traube is also applicable. The polarization experiments were conducted on pyrite in a solution containing xanthate. In the anodic polarization, xanthate is observed to oxidize to dix- anthogen, which depresses oxygen evolution on py rite at higher potential levels. In spite of the importance of the presence of pyrite in the flotation of sulfide minerals, not many studies have been made on the xanthate-pyrite system in the absence of an activator or a depressant. In an early study by Gaudin and Wilkinson,' it was pointed out that no ferric xanthate was formed on a pyrite surface, while in another study Gaudin and his collaborators2 proved the formation of a very small amount of ferric xanthate. Afterwards, Gaudin et al.3 studied the pyrite-xanthate system with a radiometric technique and found indications of the presence of adsorbed dixanthogen on pyrite surfaces. Mamiya4 studied the flotation behavior of the pyrite-xanthate system and also suggested the possibility of dixanthogen. Recently, Fuerstenau and his coworkers at The Colorado School of Mines5 studied the role of dixanthogen in the xanthate flotation of pyrite and discussed the problem in terms of such properties as oxidation potential, zeta potential, flotation recovery, pH of solution, etc. However, the mechanism of dixanthogen adsorption at the pyrite-water interface is not yet understood. This paper is concerned with an electrochemical in-vestigation through which the mechanism of dixanthogen adsorption on pyrite is interpreted. EXPERIMENTAL MATERIALS AND TECHNIQUES Pure potassium xanthates were synthesized by an

Jan 1, 1969

By J. E. Burke

THE origin of so-called annealing or recrystalli-zation twins in face-centered-cubic metals continues to be a matter for speculation, and in the present report an attempt is made to explain their origin and to account for at least a majority of the observations concerning their behavior. The fact that annealing twins are prominent only The speelmen was deformed 8 pet in compression and then indented over the lower left-hand corner in a Rockwell in-denter, and then annealed to cause partial recrystallization. Note intense twinning in heavily deformed part and slight twinning in less deformed part. The upper right-hand corner is unrecrystalized. Area reduced approximately 25 pot for reproduction. after recrystallization suggests that deformation may be necessary for their formation. In 1926, Mathewson1 reported the observation by Phillips that annealing twins are frequently parallel to strain markings which delineate octahedral planes in the deformed (and partially recrystallized) matrix, and suggested that strain markings are mechanical twins which grow into annealing twins during recrystallization. Later work by Burke and Barrett' has shown that strain markings are traces of planes upon which slip has occurred, and that there is no evidence for the formation of mechanical twins of microscopically resolvable width in face-centered-cubic metals. Mathewson3 has pointed out, however, that slip may produce twin faults, and later modifications of this hypothesis have assumed that twin faults rather than true mechanical twins serve as the nuclei for annealing twins. Carpenter and Tamura5 suggested, also in 1926, that annealing twins might form by accidents of growth. A close-packed layer of atoms can be added to the octahedral plane of a face-centered-cubic metal in two possible positions, the right position

Jan 1, 1951

By D. S. Jacobus

COMPRESSED-air motors are specially desirable, if economically practicable, for underground haulage, because they require no fuel, involve no danger of fire, and not only avoid heating and fouling the atmosphere with smoke and combastion-gases, but by the emission of expanding fresh air, cool and improve it and aid ventilation. The highest developments in the use of compressed-air motors for locomotion are to be found, in the opinion of the writer, in the principles of the Mekarski car-motor as applied to street tramways, and it is thought that notes taken regarding this system, during a recent trip to Europe, where two plants are in successful operation, at Nantes and Vincennes respectively, will be interesting to mining engineers. The plant at Nantes operates a street-line 5.2 miles long, requiring about twenty motors; the one at Vincennes about 7 miles of road. Each car at Nantes carries its own motor. At Vincennes, however, the motor-car is arranged to tow a second car containing no motor. The road at Nantes is the older, having been in successful operation for ten years, during which time neither the American consul, Mr. Shackelford, who has resided at Nantes for about five years, nor the vice-consul, Mr. Bennett, who has been at Nantes ever since the road started, has ever seen anything go wrong with the motors. DESCRIPTION OF THE RAILROA at Nantes. Motor-Car.—Two small engines are connected' so as to rotate the front axle of the car, a reversing lever being used to alter the cut-

Jan 1, 1891

By John T. Galey

Oil and gas development in southern Pennsylvania during 1937 was marked by considerably increased activity in deep-sand drilling. Nine tests were completed to the Oriskany sand: one in Independence and three in South Beaver townships, Beaver County; one in Franklin township, Butler County, two in Slippery Rock township, Lawrence County; one in Mt. Pleasant township, Washington County, which is drilling below the Oriskany, and one in Fairfield township, Westmoreland County. Two of these wells, both of which were in the Blackhawk pool, South Beaver township, Beaver County, obtained wet gas with open-flow volumes of 1.5 million cu. ft. and 3.1 million cu. ft. and closed-in pressures of 1900 Ib. The remaining seven were unproductive in the Oriskany. Two wells, one in Hampton township, Allegheny County, which is shut down temporarily as a result of a gas pocket, and one in South Beaver township, Beaver County, are drilling to the Oriskany. One deep test on the Chestnut Ridge anticline, South Union township, Fayette County, was completed after considerable difficulty as a dry gas well in the Onondaga limestone. At this locality the cherty limestone is porous as a result of fracturing. Three additional tests are under way in the area, one in South Union township, a second in North Union township, and a third in Wharton township. Completions Oil.—Despite price cuts and production curtailment of Pennsylvania Grade crude, caused largely by a decreasing demand from export markets, operation in the shallow oil areas continued at a fairly high rate and a number of good wells were completed. Some of these were new wells in close proximity to old production and others were old wells drilled into deeper pays. One new well of a number of producers drilled to the Nineveh Thirty-foot sand in the Harvey pool, Center township, Green County, made 400 bbl. of oil and 500 million cu ft. of gas the first 24 hr. The Chambers dam pool of Amwell and South Franklin townships, Washington County, yielded a number of Fifth Sand producers with initials as high as 200 bbl. Several wells in the old Mars-Butler field

Jan 1, 1938

By Alden B. Grenninger

The time-honored description of the growth of metal crystals to form polycrystalline aggregates is one in which two important steps are considered: (1) nucleation, and (2) dendritic growth, each dendrite starting from its individual nucleus and resulting (upon slow cooling, assuming no solid phase changes) in a macrograin. This picture of the process of crystallization is incomplete, and it is with the hope of enlarging upon it that the following summary and correlation of experimental results are given. Mosaic Structure For an exact definition of the mosaic structure of metal crystals—if, indeed, one can be found that will hold for all metals—one must await the results of much experimental work in this field. The writer's investigations have been confined almost entirely to copper and a few of its alloys. The following terms are proposed, and will be used in this report: Macromosaic Structure1.—Large-scale mosaic structure; more specifically, mosaic structure of a scale large enough to produce splitting of Laue spots on back-reflection Laue X-ray patterns2. The deviation from exact parallelism of neighboring macromosaics varies from a few minutes to a few degrees3. Just as there are no exact dimension limits for macrograins, so the dimensions of a macromosaic vary considerably. Macromosaic structure may often be seen on copper single crystals if they are examined carefully with critical illumination4. However, back-

Jan 1, 1936

By A. Gittens

In two recent papers stevens13,14 has compared the methods used by various investigators to calculate the contribution of grain boundary sliding to the total creep strain. In previous work Gittins15 has shown that the strain due to grain boundary sliding Egb may be estimated from the lateral, d, and vertical, v, displacements of a longitudinal marker line as it crosses a grain boundary. He obtained the formula, where nL is the number of grains per unit length measured on the specimens before creep, and \p and ?2 are, respectively, the angle between the grain boundary and the stress axis in the plane of the surface and normal to the surface (see Ref. 13, Fig. 1). The subscript L indicates that observations are made in a longitudinal direction parallel to the stress axis. It was generally found more convenient to measure the grain size of a specimen before creep; this was necessary to characterize the specimen. Stevens13,14 however prefers to define Egb in terms of NL, the number of grains per unit length after creep. Since nL - NL(l + €1) where cr is the total strain, Eq. 1 11 becomes The quantities d and ?, can be determined directly from the marker lines, while v and ?2 are found by sectioning normal to the surface. In the interior when symmetry considerations suggest that v = d and ?1 - ?2 the strain due to grain boundary sliding may be estimated from a suitable internal longitudinal marker line by the equation To determine cgb at the surface using either Eqs. |1| or [2] requires a large number of observations, particularly if many estimates of cgb are required, and also it is impossible to determine the variation of cgh with creep strain on the same specimen because the specimen must be sectioned to determine ?2. Gittins15 found that for a number of materials the sliding vectors d and v were related to each other so that provided one was measured the other could be estimated. Also during creep, grain boundaries tend to migrate to meet the surface at angles close to 90 deg,16 so that the term nL(v/tan?2)L was comparatively small when 4,- 90 deg. By determining the frequency distributions of ?2 on control specimens this term can be estimated without sectioning the creep specimen. In this way an empirical equation based on Eqs. |1| and |2| enables cgb to be determined with reasonable accuracy with fewer observations of the angles and sliding components. For B brass, the relationship between the sliding vectors indicated that ceb = 0.85nLVL . In Table I of Stevens paper this equation is stated to be incorrectly derived. However it should be pointed out that this is an empirical equation derived from Eq. |1|, based on a knowledge of the relationship between d and v and on the frequency distributions of ?1 and ?2 for a particular material under given experimental conditions. It was used only when these relationships were known, to reduce the number of observations required to estimate cb. Therefore the comment "derivation incorrect does not apply. Gittins did in fact make use of Eqs. |1| and 131. Author's Reply I must apologize to Dr. Gittins for the inadvertent misrepresentation of his work. Other slight errors in Table I have been pointed out to me. Langdon (No. 12 Table I), Gifkins (No. 7, Table I), and possibly other workers did not measure the number of boundaries per unit length after creep (A') but the corresponding quantity bejove creep (n). As Dr. Gittins points out, a completely analogous set of equations to those given in the paper can be derived by the same method: using the number of boundaries per unit length before instead of after creep. The basic equations corresponding to Eqs. [2] and 171 of the paper, from which all the others can be derived, are

Jan 1, 1968

By R. Hoffmann

The Waelz process produces oxides of volatilizable metals from ores, metalliferous products and residues. The process was originally used for recovering zinc and lead, where tailings and residues containing those metals had accumulated at mines or smelters, but it is applicable for obtaining tin, arsenic or other volatilizable metals. It is useful when other methods of obtaining the metals from the ores or residues are too difficult or expensive or show too low a recovery. The Waelz process was developed in 1923 for the treatment of large calamine dumps in Upper Silesia, which showed zinc contents of 8 to 10 per cent. and lead contents up to 3 per cent. The rapid development of the process, from the first trials up to the plants now working or in course of erection, is shown in Fig. 1. The first industrial Waelz plant was started in 1925. Within two years the capacity of the working plants reached 700 tons material per day of 24 hr. During the year 1928 the daily capacity of the plants now at work or in course of erection will rise

Jan 1, 1928

By Donald E. Cummings

Certain dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribution, except that the upper limit of size retained in the air sacs is approximately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been generally conceded, however, that particles of harmful dusts smaller than 1/4 to 1/2, micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to disregard them.

Jan 1, 1937

By J. M. Oblak, W. A. Owczarski

A cellular appearing recrystallization product formed by annealing a cold-worked nickel-base super-alloy at 1800°F has been studied by electron nzicroscopy. Prior to deformation, an equilibrium micro-structure of fcc matrix y and cuboidal ,,', Ni (Al, Ti), precipitates of CuzAu structure had been established by an age at 1825°F. The strain-free recrystallization cells consist of very large rodular y' particles in a y matrix. They precipitate is oriented and coherent both before and after recrystallization. The results showed that y' coarsening accompanies recrystallization at 1800°F. However, it does so as a secondary effect and does not necessarily take place at lower temperatures. The structural similarity of this reaction to cellular precipitation in other systems indicates that lattice strain may also play a significant role during some cellular precipitation reactions. THERE have been numerous microstructural investigations of recrystallization in single-phase materials but two-phase systems have received much less attention. The second phase can either remain inert or be altered along with the matrix during recrystallization. If the second phase is an oxidelm3 or a relatively inert pre~ipitate,~, recrystallization is retarded when the interparticle spacing is less than 1 p. Prior to the onset of recrystallization, these materials show a well-polygonized substructure with the subgrain size limited by the interparticle spacing. Since recrystallization by the motion of preexisting grain boundaries6 is not observed, retardation has been related to particle pinning of the subboundaries. This pinning prevents coalescence' or growth8 of subgrains to a critical size (formation of a high-angle boundary) necessary to initiate recrystallization. In a material such as a nickel-base superalloy both y matrix and y' precipitate are altered by the recrystallization reaction. Haessner et al.' studied the recrystallization of a cold-rolled Ni-Cr-A1 alloy by electron microscopy. The material was initially cold-rolled in the supersaturated condition. upon annealing at 750°C, immediate precipitation of 7'occurred. Presence of this 7' greatly retarded the onset of recrystallization which eventually took place by the development of randomly oriented, strain-free grains. The original •/ was dissolved at the recrystallization interface and reprecipitated as oriented, coherent par-tiles in the new grain. Recrystallization caused a refinement of .)' particle size. Recently ~hillips'' investigated recrystallization of Ni-12.7 at. pct Al. Reduction by cold rolling presumably elongated the p' precipitate into lamellae that remained coherent with the matrix. After recrystallization at 600" to 750°C, there was no unusual change in y' particle size al- though there was a tendency toward clustering along the prior rolling direction at 750°C. Above 750°C, the recrystallized grains were generally free of precipitate. Studies in the somewhat analogous Cu-3.23 wt pct CO" and Cu-2 wt pct'2 systems demonstrated that the coherent cobalt-rich fcc precipitate in these alloys obstructed softening, initiation, and completion of recrystallization. The precipitates were deformed into lam~llae during rolling and those of diameter less than 250A remained coherent. Recrystallization took place by the growth of new grains into the recovered or poly-gonized material. In the first study," both matrix and precipitate reoriented in the same manner upon passage of the recrystallization interface. There was no change in particle size or morphology. Tanner and ~ervi,~ on the other hand, observed that motion of the recrystallization fronts was strongly hindered by the pinning action of coherent precipitates in the deformed material. Particles in contact with a pinned boundary coarsened and coalesced leaving a denuded zone in the unrecrystallized region. When the number of pinning points was sufficiently reduced by coalescence, the boundary swept past these particles and through the denuded zone. The authors1' considered this as a variation of discontinuous precipitation with both chemical driving force and deformation strain energy contributing to recrystallization. Preliminary observations by the present authors had revealed that recrystallization in Udimet 700, a nickel-base superalloy, occurred in an entirely different manner. Optical metallography showed that the recrystallized product formed as cellular colonies containing coarse y' particles elongated in the direction of cell growth. In this investigation the structural features of this reaction were investigated by transmission electron microscopy. EXPERIMENTAL PROCEDURE As-received I$-in. rounds of Udimet 700* were (wtpct) 18.4 15.2 4.95 4.42 3.43 0.06 0.031 0.14 Bal. solution-annealed for 4 hr at 2150" and then fast air-cooled. An initial y-~' structure was established by a 4-hr age at 1825°F followed by a fast air,cool. Essentially the equilibrium volume fraction of ?' at 1825°F is precipitated within 4 hr. Microstructural examination showed no measurable increase in the amount of precipitate after longer aging times. Deformation consisted of swaging to 52 pct RA with 6 pct reduction per pass at room temperature. To reduce the precipitation potential to a negligible amount, recrystallization anneals were conducted at 1800"~ (982"~). Microstructures were investigated by optical and transmission electron microscopy. To prepare foils for electron microscopy, the material was first sliced into 30-mil slabs parallel to the swaging direction. Discs were dimpled and electrolytically cut from

Jan 1, 1969

By A. J. Garnier, N. H. van Lingen

Rock downhole is known to be lesc. drillable than when brought to the surface. This must be ascribed mainly to the presence under downhole conditions of a pressure differential across already made chips, which hinders their being lifted. The pressure differential has partly a static and partly a dynamic origin. Balling-up of bits is another consequence of this pressure differerztial. Reduction in penetration rate owing to an increase in the strength of the rock is governed by the difference between the mud pressure and the pressure of the for/nation pore liquid. Rotationally symmetric geostatic stresses have 170 effect on drillability. Fracture of rock when drilling will be brille in most cases. The above is supported by laboratory drilling experiments with drag bill and roller bits an elevated mud, pore, and confining pressures On rocks differing in strength and permeability. INTRODUCTION In oil well drilling drillability of rock is found to decrease with increasing depth of the hole. Naturally deep rock will be more compacted and, therefore, harder to drill than shallow rock of the same type. However, apart from this the drillability of a sample of deep and compacted rock brought to the surface is generally much higher than in its original location downhole. In view of the economic implications of this reduction in drillability, it seems worthwhile to analyze its causes. The origin clearly has to be sought in the difference of environment. The only conceivable factors would seem to be the presence of mud under pressure, the pressure of the formation pore liquid, and the overburden of the rock. Down the borehole the rock is compressed triaxially by mud pressure and overburden. It is well known that the strength of rock is increased when confined by external pressure1. Various authors have, therefore, ascribed the difference in drillability mainly to the strengthening of rock by triaxial compression. Another factor, mentioned by Bobo and Hoch5, is that forces. including "pressure differential forces", tend to hold a dislodged particle in place. However, the conditions determining their magnitude are not clarified nor is their effect on drilling rate assessed. In the laboratory, drilling experiments on pressurized samples of rock yielded evidence that pressure differential forces holding the chips down are the major factor in reducing rate at depth. This paper describes the experiments and shows how the results enable both a qualitative and a quantitative interpretation of the factors determining the effect of chip hold-down on drilling rate. The implication with respect to balling-up and jet action is also discussed. The greatcr part of the experiments were performed in the pressure vessel shown in Fig. 1. The spacc between the sample of rock and the vesscl is divided by "0" rings into three separate chambers. The rock sample is confined laterally by pressurized oil in thc middle chamber. Penetration of oil into the sample is prevented by partly jacketing it with brass foil. Thc pressure of the drilling fluid in the hole can be adjusted via the upper chamber. Permeable rock specimens arc water saturated before being drilled. With a properly plastering mud as drilling fluid the pressure of the pore water can be adjusted independently via the lower chamber.

By H. DeWitt Smith

THE mine operated by the United Verde Copper Co. is situated near Jerome, Ariz., on the eastern flank of the Black Hills, at an elevation of approximately 5500 ft. (1676 m.) above sea level. The mine and the town of Jerome are located on a steep hillside, which slopes rapidly to the valley of the Verde River. The smelter town of Clarkdale is situated in the Verde valley 4.1 mi. (6.5 km.) distant in an air line from Jerome, and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel & Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 mi. long and has a compensated 4 per cent. grade. At Clarkdale, it connects with the Verde Valley branch of the Santa Fe R. R. The narrow-gage (36-in.) line of the United Verde & Pacific Ry. was, until 1919, Jerome's only rail connection with a main trunk line. This road connects with a branch line of the Santa Fe system at Jerome Junction, after traversing 26 mi. of mountainous country. From the time of its location, in 1876, until its purchase by Senator W. A. Clark, of Montana, in 1889, the United Verde mine was worked on a small scale and shipments of high-grade gold-silver ore were made from the surface workings. Until 1894, when the narrow-gage railroad to

Jan 8, 1920