Search Documents

By G. R. Speich, S. A. Kulin

R. C. Shnay (Dept. of Mines and Technical Surveys, Ottawa, Ont., Canada)-—The authors are to be congratulated on an interesting and informative paper. However, several questions arise when the isothermal formation of martensite .is considered in relation to the formation of bainite at temperatures near the M, point. The reactions in an alloy and in a plain carbon steel would appear to be comparable; and in the course of a recent investigation of the austenite-bainite transformation in a plain carbon steel,Ia the writer has obtained data at temperatures above and below the M, point. These data are in some respects similar to those of the authors and a comparison would seem justified. The steel used in this investigation had the nominal composition: C, 0.80 pct; Mn, 0.20; and Si, 0.20. The course of the transformation was followed by the use of a magnetic balance. The magnetic moment of the specimen as determined by this instrument is directly proportional to the percentage of the total volume of the specimen which has transformed to bainite. ~lf specimens were austenitized at 1850°F for 4 hr, quenched to the transformation temperature, and quickly transferred to the magnetic balance. Readings were taken at regular intervals until the transformation had stopped. A typical transformation curve is shown in Fig. 9. The preliminary curve preceding the S-shaped curve was found at all temperatures above the M, to around 600°F. Both the extent of this preliminary curve and the time interval between it and the S-shaped curve were found to decrease with increasing temperature as was suggested by Davenport and Bain.14 Therefore,

Jan 1, 1953

By D. J. Schmatz

DISCUSSION OF RESULTS The qualitative correlation between low-temperature ductility and prior high-temperature creep strain in nickel obtained in this investigation confirms the result obtained on high-purity brass by Chen and Machlin. However, the quantitative effect is much smaller in nickel. Comparison can be made on the basis of a prior high-temperature strain that is a certain percentage of the total high-temperature elongation to rupture. In the research of Chen and machlin, the prior high-temperature strain of 1/2 pct equaled 8.5 pct of the total high-temperature elongation at rupture. For nickel, in our experiments, 8.5 pct of 21.2 pct equals 1.8 pct. For eh = 1.8 pct, the loss in ductility in percent equals x 100 = b.5 pct. That is, for equivalent bo Formation of Beta Manganese-Type Structure in Iron-Aluminum-Manganese Alloys D. J. Schmatz IRON-aluminum alloys have gained much interest in the past few years for use as a base material for elevated-temperature alloys because of their excel- high-temperature strain the loss in low-temperature ductility is 8.5 pct for nickel as compared to 60 pct for pure a, brass. It is also interesting to note the observation that in nickel the low-temperature fractures, even at the most extreme high-temperature pre-strain, were partly trans crystalline and partly intercrystalline. In the case of a brass, these fractures were completely intercrystalline. According to the data on the percent of the grain boundary area that is cracked, at 22 pct high-temperature elongation, about 12.5 pct of the grain boundary area does not carry load. Thus, the inter-crack areas are carrying a stress that is about 11 pct higher than the nominal stress. A simple model predicts that the overall elongation, which is primarily the elongation in the bulk of the specimen, will correspond to the nominal stress when the stress in the intercrack area equals the tensile strength. Quantitatively this model predicts the equation The form of this equation will agree with that found if the strain-hardening exponent, n, equals unity. Actually this model is too gross an approximation to yield good quantitative results. The question naturally arises as to whether in ordinary hot-working, such as hot-rolling, intercrys-talline cracks are introduced that affect the low-temperature properties. It appears that the answer is that such a possibility cannot be overlooked, if the hot-working induces tensile stresses at temperatures above the equicohesive temperature and if the material tends to be notch sensitive at low temperature. ACKNOWLEDGMENT This research was supported by the Aeronautical Research Laboratory, Directorate of Research, Wright Air Development Center, United States Air Force. REFERENCES lC. Zener: Fracturing of Metals, 1948, Cleveland, ASM. 'H. C. Chang and N. J. Grant: Mechanism of Intercrystalline Fracture. AIME Trans., 1956, voL 8, p. 544; lownal of Metals, May, 1956. 'E. S. Machlin. CreepRupt ure by Vacancy Condensation, AIME Trans., 1956, vol. 8, p. 106; lownd of Metals, February, 1956 'C. Chen and E. S. Machlin: On a Mechanism of High-Temper at ure Inter-crystalline Cracking, lownd of Metals, July. 1957. p. 829. Alloys lent oxidation resistance. Binary alloys of aluminum in iron are ferritic and consequently have poor hot strength. Alloys of iron-aluminum-manganese were made in an attempt to produce an austenitic alloy containing sufficient aluminum to retain the oxidation resistance of binary alloys of iron-alumi-

Jan 1, 1960

By D. T. Peters, J. C. Bisseliches, J. W. Spretnak

The pain boundary relaxation phenomenon in high-purity copper, 0FHC copper, and a precipitation-hardenable alloy o-fCu-2 uit pct Co has been studied by internal ,friction and elastic aftereffect techniques. The data were analyzed by assuming the broad distribution of relaxation times observed obeys a lognormal distribution law which enables calculation of the relaxation strength. Grain size had no effect on relaxation strength, although the peak width increased with increasing grain size and decreasing temperature. A double grain boundary peak was produced in high-purity copper by annealing to produce secondary recrystallization. The activation energy measured for 99.999 pct Cu is 37.5 * 3 kcal per mol and 46.5 kcal per mole for OFHC copper. A small peak in the Cu-Co alloy at about 220°C at 1 cps was deduced to be the grain boundary peak. Its height increased and its activation energy decreased with increasing aging time. Except for erratic peak positions the observations were consistent with the theory of pain boundary sliding. BEFORE the mechanism of the grain boundary internal friction peak in metals can be satisfactorily explained, the detailed characteristics of the relaxation process must be documented. Of interest are the effect of grain size on relaxation strength, the high-temperature background, and peak width and position. The effect on the grain boundary peak of a precipitate at grain boundaries and of the change in distribution of the particles with aging time must also be explained by any existing or forthcoming theory. The model which has received the most attention was proposed by KG' and zener2 and proposes that the anelastic strain results from sliding of adjacent crystals at grain boundaries. The sliding is limited by the interlocking of grain corners. It follows, according to this model, that the relaxation strength is independent of and the relaxation time is proportional to the grain size. The proportionality between grain size, D, and relaxation time, t, has been confirmed by K&' and Bisseliches . In this case, the internal-friction peaks of various specimens can be superimposed by plotting Q-' as a function of the parameter vD exp H/RT where v is the frequency and H the activation energy. However, the data of Starr et 01.' and Leak6 fit better to a parameter containing D to an exponent near two. A meaningful relationship is not always deducible from the shift of peak temperature with grain size. KG7 demonstrated that a twofold variation in grain size obtained by varying the amount of cold work followed by identical recrystallization anneals will cause a peak shift that is too large to be accounted for even by an exponent of two. Since the decreased grain boundary area existing with a larger grain size is exactly compensated for by an increased sliding distance, the relaxation strength should not decrease with increasing grain size. The height of the internal-friction peak has generally been observed to be rather insensitive to grain size as long as the average grain diameter does not approach the specimen diameter. Exceptions have been reported by Koster, Bangert, and Lang8 for copper, and by Leak6 for iron. The observations for copper could well have been confused by the presence df 0.3 pct0. The possibility that the peaks may simply be increasing in width with increasing grain size and that the relaxation strength, which is proportional to the area under the peak, may remain constant was not examined. his point has been checked in this investigation using high-purity copper. Atomic mechanisms to account for damping by sliding at grain boundaries have been proposed by KG7 and Mott. KG predicts the activation energy to be identical to that for self-diffusion. Mott's "island" model suggests the activation energy is nL where n is the number of atoms in an island and L is the latent heat of fusion per atom. Other authors have felt that a value equal to the activa-

Jan 1, 1964

An abstract of a paper from the Canadian Mining and Metallurgical Bulletin of August 1978 by E. Stamboliadis, J. McHardy, T. M. Salman, Department of Mining and Metallurgical Engineering, McGill University, Montreal, Quebec, states that: “The recovery of gold, silver and other heavy metal cyanides from mill solutions is technically possible using the ion exchange technique. However, the costs involved are greater than the costs of the zinc precipitation technique used for gold recovery. There are two main reasons for this: one, the fact that in gold ore cyanidation metal cyanides other than gold and silver occupy most of the resin capacity and hence reduce the adsorption efficiency of the resin for the Au and Ag cyanides; secondly, the high cost of the eluting agents.” Resin, therefore, cannot in most cases be efficiently used for recovery of precious metals. With copper in solution, only 1.47% of the resin capacity is used for gold and 0. 8970 for silver; the rest is occupied by unwanted metal cyanides, such as copper occupying 73.7%. On the other hand, although activated carbon will adsorb copper cyanides, they will be preferentially displaced by gold and silver cyanides. Ion exchange is by one or two orders of magnitude more expensive than the conventional method of zinc precipitation. The cost of removing impurities, such as copper from the resin, is greater than the cost of recovering gold. With an oxide ore amenable to cyanidation and with a low content of other metals, such as may occur with some of the Soviet gold deposits, ion exchange would be an efficient as Carbon-In-Pulp.

Jan 1, 1981

By J. S. Li, J. C. Edwards

A prediction is made of the airflow at the Bureau of Mines Lake Lynn Laboratory with a ventilation computer program that accounts for fan-driven forced ventilation and temperature-induced natural ventilation. There was substantial agreement between measured and predicted airflow rates. The capability of the program is demonstrated as a planning aid for ventilation under emergency conditions in a multilevel coal mine. Smoke spread in a multilevel mine is analyzed following the occurrence of two events, the failure of the main exhaust fan and the development of a fuel-rich fire in a passageway.

Jan 1, 1983

By H. H. Wright

In many fields edge water is one of the most important factors governing the production of oil. Possibly this fact is not appreciated by many producers except in so far as it may bring about a loss in production from wells drilled on the flanks of structures. In the light of artificial flooding as practiced in New York and Pennsylvania, and of the beneficial effect of natural water-flooding on many wells and leases in the Mid-Continent and elsewhere, it seems reasonable to suppose that very few phases of the petroleum industry hold greater promise for future benefit than the study and control of the natural water drive. Rate of Water Encroachment The rate of movement of water in artificially flooded areas has been referred to as so many feet per unit of time, usually from an injection well toward surrounding producing wells. This definition is vague when used in reference to the movement of natural edge water, inasmuch as such factors as sand thickness, steepness of dip and horizontal extent arc not considered. In the ultimate analysis, only the vertical component of movement affects the production of oil in the natural drive, and in order to define the rate of water encroachment more exactly, such a term as acre-fect per unit time might be used. Thus, where one well is located to each 10 acres a vertical movement of 5 ft. in the water level in a year would be defined as an encroachment of 50 acre-feet per year, and where one well is located to each 20 acres, as 100 acre-feet per year. Such a definition as this is entirely arbitrary, but it takes into consideration to a certain extent the influence of well spacing, and consequent sand drainage, on the rate of water movement. The rate of movement is considered to be an important function of water encroachment, for it is believed that the efficiency of recovery by natural water flood depends a good deal upon the rate of movement. In general, rapid encroachment is thought to effect a poor recovery because of the differential in favor of the movement of water through a sand body and the consequent tendency to trap oil in the sand. Slow movement, on the contrary, is thought to bring about a partial displace-

Jan 1, 1931

By H. Landsberg

MANY of the sedimentary rocks contain small amounts of radioactive constituents. These vary in quantity in different layers. Some recent deposits show rather high activity as; for example, the deep sea oozes and some lake deposits.1,2. Measurements made in boreholes have also shown considerable changes in activity from horizon to horizon. The first to publish data on this fact was Ambronn,3 and recently Russian geophysicists have shown remarkable variations of activity from one layer to the next in various wells. Spak4 felt even that he was able to line up horizons from data measured in two neighboring wells. ? The measuring of radioactive radiation is fairly difficult. Large errors are possible by the circulation of gaseous emanations in the well and porous strata. It is, therefore, never certain whether the activity of the layer where the instrumental device or collector is located will be measured, or that of some adjacent layer, For this reason it seemed to be advantageous to take samples of rocks into the laboratory and test them therefor their contents of radioactive material, Such a method has been followed in the past to distinguish radioactive ore from other rocks. Radioactivity of rocks, especially of the igneous type, was also deter-mined in the laboratory by numerous authors for absolute age investi-gations.6 Corresponding data from studies of sedimentary formations are scarce. Specimens taken from a core of the Bradford oil sandstone were tested by Landsberg and Ingham,7 with the results illustrated in Fig. 1, which shows that within relatively small vertical distances the differences of relative activity were considerable. If one assumes that the distribution of radioactive material is fairly uniform throughout a layer, measurements of radioactive radiation in various horizons would offer additional information for stratigraphic

Jan 1, 1939

By H. E. Williams

In view of the frequent occurrence of petroleum in other parts of the world, it seems odd that so large an area as is contained within the borders of Brazil should be without this product. This apparent deficiency may be due, however, to our ignorance of the regions in which it may exist. In some places, indications point to the probable existence of petroleum in ages gone by; and while the presence of petroleum pools may be problematic, in several regions conditions not unfavorable to their occurrence exist. Yet, Brazil has enormous oil resources in the rich oil-shales in different parts of the country. Many of these shales are very rich and only suitable processes for the extraction of the oil are lacking. At the present time, only a few small experimental plants are producing oil by distillation from these shales. These plants have been the subject of recent investigations by the Geological and Mineralogical Survey, a preliminary report of which is in the hands of the printer. The only regions where studies have not been made are the upper Amazon, the Acre, the Rio Negro, and the Peruvian frontier, which really seems to be the most promising field for explorations of any in the country. In the vast plateau region of the interior north of the 20th parallel of latitude, granites, gneiss, mica schists, and very old metamorphosed sedimentaries predominate. Later, sedimentaries occupy a minor position and, where found in the interior, represent a thin veneering resting on the older rocks. At several places near the coast they have a greater development and contain considerable beds of oil-shale and may, .in some cases, offer conditions favorable for the occurrence of oil. Such deposits are found in the Permian rocks of central and southern Maran-hao; in the Tertiary and Cretaceous beds along the coast of Alagsas Sergipe, Bahia, and perhaps farther south in Espirito Santo; and in the Parahyba embayment north of Cape Frio and in the interior Tertiary basin of eastern Sao Paulo.

Jan 1, 1921

By S. F. Emmons

IT was said by many who discussed Professor Posepny's admirable paper on the " Genesis of Ore-Deposits," read at the Chicago meeting of the Institute, in 1893, that its most valuable feature was the clear distinction which it drew between the influence upon ore-deposits of the "vadose " circulation of waters descending directly from the surface, and that of the deep underground circulation of waters generally coming from the depths, and assumed by the author to be ascending through more or less open spaces under the influence of heat. A little later the effect of the oxidizing action of the vadose circulation upon ore-deposits was ably and exhaustively treated by Prof. R. A. F. Penrose, in a paper on " The Superficial Alteration of Ore-Deposits "f-the only one, so far as I know, which has been exclusively devoted to this important subject. My own first detailed study of ore-deposits was made at Leadville, in 1880, at a time when almost the only minerals visible in those deposits were in oxidized forms. That this form was the result of the alteration of earlier sulphides by surface-waters had to be proved at the time by induction or analogy, the general correctness of which was, however, abundantly confirmed by subsequent developments. Thus I was early impressed with the importance of distinguishing, in the study of an ore-deposit, the alteration-products, resulting from the action of oxidizing waters descending from the present surface, from the earlier-formed sulphides; and, assuming that the latter were primary or original, I called the former secondary. I also went so far as to say$ with regard to oxidized ores passing into sulphides in depth "So generally is this accepted as a rule in ore-deposits that it would require special demonstration to prove beyond a doubt that the native metals or their

Jan 1, 1902

By R. F. Hehemann, Darrell W. Smith

The kinetics of alloying- in W-5 rot pct Re powder compacts were investigated at temperature about the upper limit for the formation of the x phase, such that a single intermediate phase was involved in the process. The rates and directions of motion of the a-o and o-b interface were assessed as functions of tinze at the sintering teri7peraticve by quantitative izetallog-ralhic techtziques. The iiotion 01 these interjuces could be specified approxitnate1.y by u Parabolic )-ate law and deviations from this ,rate law were attribuled to a complex interaction between surface dif'fusion and volume diffusion during the initial stages of sintering. WHEN binary or more complex alloys are produced by sintering compacted blends of elemental powders, a complication is encountered which does not arise in the sintering of pure metals. In addition to concern for grain size and densification, the rate of inter diffusion of the component elements must be considered. The general problem of alloying during sintering has been treated by numerous investigators.'-7 These investigations have been concerned only with systems that form continuous series of solid solutions and a concentric-sphere diffusion model4 provides a useful description of homogenization in these stems.' Some controversy remains, however, over the contribution of surface and grain boundary diffusion to the homogenization process. Heckel% ePorts that homogenization can be described by volume diffusion at all temperatures, whereas other invetiators'' recognize the importance of surface and grain boundary diffusion, particularly at lower temperatures. Analysis of the homogenization process in partially miscible systems is complicated by the motion of the interfaces separating the individual phases. A simple analytical solution does not exist for such finite systems with spherical symmetry. It was the purpose of this work to examine the kinetics of the formation and dissolution of an intermediate phase in a binary system through an assessment of the motion of the interfaces separating this phase from the terminal solid solutions. PROCEDURE The W-Re system is an example of a partially miscible binary system and was selected for study because of its current importance in refractory-metal technology. The equilibrium phase diagram, Fig. 1, shows that the o phase will be formed by interdiffu-sion between tungsten and rhenium. At temperatures between approximately 2125" and 282O°C, the o phase will appear as the only intermediate phase in the diffusion system. In this work, a mixture of elemental powders containing 5 pct Re was employed. In such a mixture, the rhenium particles will be distributed randomly in a tungsten matrix. During sintering, a o-phase layer will form at the W-Re interface. The development and subsequent disappearance of the o phase are controlled by the relative rates and directions of motion of the 0-0 and a-p interfaces. The motion of these interfaces can be inferred from quantitative metallographic measurements of the average radii of the o shells surrounding rhenium particles. Elemental tungsten and rhenium powders of commercial purity were employed in these investigations. The rhenium powder was spheroidized from +200 mesh agglomerates by plasma-arc spraying and was then classified to yield a powder composed of essentially

Jan 1, 1967

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By C. H. Ma, J. S. Makris

This paper describes a modified X-ray diffraction microscope wzethod based on the general principles of Berg-Bawett's Method, Lang's Method, and Woosters1 Technique. This new method may be used for stationary or oscillatory photomacrographs, with both reflection and transmission techniques. In the stationary technique, a small point-source of a divergent X-ray beam of white radiation is used; in the oscillatory technique, a monochromatic divergent beam is employed. The chief advantages of the method described herein are that only approximate alignment of the Bragg angle -of-interest is needed during exposure, and that a large portion of a crystal-specimen surface can he irradiated. In recent years, the study of dislocations through X-ray diffraction microscope techniques has received considerable attention as concerns the per,fection of single crystals. Very promising results have appeared in the literature.'-' These techniques are very useful when the dislocation density of a crystal is near 105 per sq cm or lower. The principle of X-ray diffraction microscopy is based on the differential effect of X-ray primary extinction between the distorted parts and the perfect parts of a crystal. When an X-ray beam impinges on a set of planes of a crystal at the correct Bragg angle, diffraction of X-rays will occur with a 90-deg phase shift of the diffracted beam. This once-diffracted beam still forms the correct Bragg angle with the planes ahead of it, if the planes are not distorted. Thus, part of the strength of the once-diffracted beam is rediffracted and the beam continues to travel in the direction of the primary X-ray beam. This twice-diffracted beam not only takes away part of the strength of the once-diffracted beam, but also causes destructive interference with the primary beam because it now is exactly 180 deg out of phase with the primary beam. As the primary beam goes farther and farther into the crystal, its intensity is continuously weakened. Asa result, the ultimate X-ray diffraction power of a set of undistorted planes is largely extinguished. This phenomenon is called primary extinction.1,2'4 If the set of planes ahead of it is distorted, the once-diffracted beam will have less chance to be rediffracted, because it could not meet the exactly correct Bragg angle for rediffraction. If a part of the beam does rediffract, this twice-diffracted beam is not exactly 180 deg out of phase with the primary beam, and thus it causes less destructive interference. As a result, the registered X-ray diffraction power of the distorted part of a crystal appears stronger than that of the perfect part. Thus, point-by-point contrast of a diffraction image is theoretically possible from a crystal containing dislocations. Two most popular X-ray diffraction microscope techniques today are Berg-Barrett's Method and Lang's Method. Both of these techniques require a

Jan 1, 1964

By A. Boltax

Precipitation processes occurring during both furnace cooling and aging of copper-iron albys were studied by means of electrical and magnetic measurements. On furnace cooling, two distinct stages in the precipitation process were detected; one occurring above and the other below 850° C. The kinetics of precipitation from quenched alloys were studied between 200° and 700°C. The reaction appears to be consistent with the concept of tmcleation of precipitate particles at dislocation loops formed by the clustering of quenched-in vacancies. A study Of in copper-iron alloys is particularly interesting because the combination of magnetic and electrical properties in these allovs provides a quantitative means of following the course of the precipitation reaction. (The details of precip-

Jan 1, 1961

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

By R. G. Garlick, H. B. Probst

Tungsten single-crystal specimens of various orientations were deformed in tension at room temperature. Slip traces indicated both (112)(111) and (110) (111) slip; however, about 10 pct plastic dejormation was required bejore these traces could he seen. Resolzled shear-stress considerations indicated that at least some of the particular systems observed were not those on which slip initiated hut were secondary systems. This is highly probable, considering the high plastic strains involved. Analysis of the stress data with respect to possible slip systems indicated that slip must have been initiated at stresses below the proportional-limit stresses measured. ALTHOUGH there is general agreement that slip deformation in fcc and hep metals takes place on the plane of close packing and in the direction of close packing, there is no such agreement for slip in bcc metals. It is generally agreed that the close-packed direction (111) is the slip direction, but investigations have led to conflicting descriptions of the slip plane. As Hoke and Maddin1 point out, there are essentially four points of view. 1) Deformation in bcc metals is composite shear on (112) and (110) planes or on nonparallel (110) planes, and any apparent slip on other planes can be accounted for completely by slip on these planes. Chen and Maddin have reported this to be the possible case for molybdenum." 2) Slip occurs in the (111) direction and is limited to {110), {112), and (123) planes (the three closest packed planes of the lattice). 3) Slip occurs in a (111) direction, but not necessarily on planes of close packing (banal slip). 4) Slip occurs in those directions and on those planes for which ß, the ratio of Burgers vector to interplanar spacing, is a minimum. The slip systems of the bcc metal tungsten have never been fully determined, although several investigators have reported pertinent results.3"7 The present work was initiated to determine the active slip systems in tungsten at room temperature, the critical resolved shear stresses associ- ated with these systems, and the orientation dependency of operative systems. These features of tungsten deformation at room temperature have never been reported in the literature. The authors find this somewhat surprising, particularly in view of the availability of tungsten single crystals since the advent of electron-beam zone-melting techniques and the widespread interest in refractory metals. It would seem apparent that such work has been attempted but the results have not been reported, possibly due to the conflict with deformation theory. The results of the present work conflict with any straightforward description of deformation based on the proposed explanations of slip in bcc metals. Although these conflicts have not been resolved, a presentation of the problem seems in order and should be of value to others working in this field. MATERIALS AND PROCEDURE Single-crystal tungsten rods of 1/8-in. diameter were grown from undoped commercial rod by one-pass electron-beam zone melting in apparatus previously described by witzke.8 Representative analyses of the rod before and after melting are given in Table I. There was no detectable zoning of impurities during melting. Buttonhead tensile specimens, as shown in Fig. 1, were machined from single crystals. Two flats 90 deg apart were ground in the gage length of each specimen. These flat surfaces facilitated the analysis of slip traces. No attempt was made to position these flats with respect to the crystal orientation. The worked surface layer of the machined specimens was removed by electrolytic polishing in a NaOH solution. Tensile-axis orientations were determined by standard Laue back-reflection techniques. The sharpness of the Laue spots indicated that the crystals were free of strain.

Jan 1, 1964

According to the June 27 issue of Business Week, Rep. Kearns (R., Pa.) introduced a bill in Congress along lines suggested by the National Society of Professional Engineers, to amend the Taft-Hartley Act to permit scientific, technical, and professional groups to discuss wages, hours, and working conditions with management-with the protection and support of the federal law. The article reports that the bill is opposed by a loosely knit group of professional and technical unions, the Engineers & Scientists of America. This group wants Taft-Hartley amended to make it an unfair labor practice for employers to discuss collective bargaining matters with professional organizations.

Jan 9, 1953

By Chas. A. Ashburner

THE Bradford Oil District lies in the northern part of McKean County, Pa., and the southern part of Cattaraugus County, N. Y. Although petroleum was first found in the producing sand in 1871, it was not until the early part of the year 1875 that a productive horizon was acknowledged to exist, even by those most largely interested in the production of the crude oil. It has been reported to me that the first well drilled in the valley of the Tuneangewant Creek (commonly called Tuna Creek) was drilled by F. E. Dean and brothers in 1865. This well was located on the Shepherd farm, near the present site of Custer City. One hundred and sixty feet of drive pipe was used, and the hole was drilled to the depth of 900 feet. The producing sand at Custer City is found about 1130 feet below the level of the railroad track. The Shepherd farm well was therefore abandoned over 200 feet above the top of the oil sand. The next well was drilled by the Dean brothers on the Clark farm at Tarport. Drilling was stopped at a depth of 605 feet, or over 400 feet above the top of the oil sand. In the year 1862 the old Bradford well, since known as the Barnsdall well, was drilled to a depth of 200 feet with a spring pole, and then abandoned. In the spring of 1866 the citizens of the village of Bradford concluded to club together and sink the Barnsdall well deeper. It was drilled to a total depth of 875 feet, or to within 150 feet of the Bradford producing sand. All of these wells were drilled with the expectation of finding the Venango County oil, and at

Jan 1, 1879

By H. C. Miller

The gas-lift method of flowing oil from wells is the outstanding feature of petroleum technology today. Its forerunner, the air-lift, was used successfully first, in the Baku fields of Russia, in 1899, and later in the Gulf Coast fields of Texas and Louisiana and the Kern River field of California. It is still used to a limited extent in certain oil fields. The use of compressed natural gas for lifting oil from wells has supplanted the air-lift method in a measure in those fields where a sufficient quantity of gas accompanies the oil to make the gas-lift possible, or where natural gas is plentiful and inexpensive. We find, therefore, in California, that natural gas is used at practically every well where a gaseous medium is employed to flow the oil. The use of natural gas has many advantages over that of air. It is possible to recover and save the gasoline from the gas that accompanies the oil to the surface. This gasoline would be wasted if air were used as the lifting medium. Also, certain proportions of air and gas form an explosive mixture that cannot be handled safely by compressors. Another advantage that gas has over air is that gas under pressure is more soluble in oil. Gas in solution in oil reduces the viscosity of the oil that is being produced and causes it to flow more readily through the tubing and flow lines. The gas-lift has made it possible to recover many thousands of barrels of oil from deep wells in California that could not have been produced otherwise. It would not have been economical, had it been mechanically possible, to produce such wells as the world's deepest producing oil well (Miley Athen's No. 6, Rosecrans field, California) by any other method of pumping known today. At this well, production is obtained from between 7305 and 7591 ft. and 11 months after completion of the well, production was being maintained on the gas-lift at approximately 2000 bbl. a month. The crookedness of the hole, or its diameter and depth will not prevent the successful application of gas-lift pumping when other conditions are favorable.

Jan 1, 1928

By C. Richards Honeycutt, Frederick C. Langenberg, Guenter Pestel

Solidification in a moving electromagnetic field was successful in altering the as-cast grain structure of steel ingots. The equipment is described and exerimental results are presented for several different alloys. Conditions for optimum grain refinement are described and an empirical design constant presented. The effect of the grain refinement on hot workability is briefly discussed. T HE grain structure of a steel ingot teemed into a metal mold can be defined by macroscopic examination in semiquantitative terms. For example, the relative volume of obviously differing structures can be estimated with the classic definitions of chill, columnar, and equiaxed zones. Experimental evidence has proven that the grain structure of an ingot is affected by changes in such factors as teeming temperature, rate of teeming, degree of turbulence, size of ingot, mold characteristics (including preheat temperature, design and coating), and composition of the metal (especially as it affects the range of solidification). Significant advances have been made in fundamental solidification studies; but the principles which have been developed are difficult to apply tothe complex and changing phenomena that occur simultaneously during ingot solidification. In particular, many attempts have been made to refine the as-cast structure of ingots, with special emphasis on the columnar grains. The formation of large columnar grains is generally considered harmful to the further fabrication of an ingot. It may also result in undesired ani-sotropic properties. However, columnar grains are not undesirable in all grades, or product applications, and caution must be exercised to determine in which grades and applications columnar grains are not desired in the ingot. Although the literature on the refinement of as-cast ingot grain structures is too vast in general to review here, it is noteworthy that such methods are additions of artificial nuclei, mold vibration, mechanical stirring or ultrasonic agitation of the molten metal, and controlled cooling and reheating during solidification have been tried with varying degrees of success. However, it is doubtful that any method of refining the as-cast ingot grain structure has been completely successful on a commercial basis. The purpose of

Jan 1, 1962

By J. Wade Watkins, E. S. Mardock

The accurate evaluation of reservoir-performance characteristics in the secondary recovery of petroleum by water flooding requires use of a water tracer that may be injected into water-input wells and detected at oil-production wells to supplement data obtained from core analyses, wellhead tests, and subsurface measurements. Radioactive iodine has been used successfully as a water tracer in field tests to determine: (I) relative rates and patterns of flow of injected water between water-input and oil-production wells and (2) zones of excessive water entry into oil-production wells. Laboratory evaluations of potential water tracers, previous tracer studies, the value of using a radioactive tracer, general field procedures, and the use of surface and subsurface instruments for the detection of the emitted gamma radiation, are summarized. Data from the field tests are presented graphically and discussed in detail. It is concluded that the radioactive-tracer method, using radioactive iodine, may be used successfully to measure either the relative rates and patterns of flow or zones of excessive water entry into wells under conditions of comparatively rapid transit time between wells. INTRODUCTION Extensive use is made of data obtained from core analyses, wellhead tests, fluid characteristics, and subsurface measurements in evaluating the sweep efficiency of water injected into oil sands for the recovery of oil. Theoretical flow rates and patterns may be calculated from those data using radial-flow formulas, if it is assumed that the physical conditions in the productive formation are homogeneous. Unfortunately, homogeneous conditions rarely, if ever, exist in oil-productive formations. The use of a tracer that may be injected into an oil sand and detected quantitatively, or even qualitatively, at offsetting oil-production wells provides basic data that may be used in determining more accurately the subsurface rates and patterns of flow of injected water between wells than is possible by theoretical calculations based on assumed conditions. Consideration of the data obtained by using a water tracer assists in the application of remedial measures to water-input wells, such as plugging of channels, or selective plugging of highly permeable zones, thereby effecting a more uniform flood and a greater ultimate oil recovery. A water tracer should have the following characteristics: (1) low adsorption on solid reservoir material; (2) high solubility in water; (3) low or negligible solubility in crude petroleum; (4) a wide range of solubility of compounds that may be formed by chemical reactions with ions present in reservoir rocks or waters; (5) high detectability in low concentrations by portable apparatus; and (6) general availability at low cost. Additional desirable characteristics are that the tracer should be nonhazardous in nature under normal working conditions and quantitatively detectable in the well bore, as well as at the surface. Review of Previous Tracer Studies The need for a water tracer has been recognized for many years. As far back as 1906, Dole1 described the use of fluorescein in flow-rate studies made in France in 1901. In 1921, Ambrose" discussed in detail the use of organic and inorganic dyes, chlorides, nitrates, and other anions, lithium salts, and the Slichter electrical

Jan 1, 1955