Search Documents

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4º; wet-bulb, 57.4º; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down- cast shafts; however, the variation between winter and summer causes a difference of only 2º to 3º in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of the mine are as follows: [ ] There appears to be no difference in rock temperature for any particular horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock temperatures given above is 1 ½ º per 100 feet. Underground Waters.-The underground water varies from 350 to 565 gal. per min., depending on the rainfall. The limestone and other

Jan 1, 1938

By M. H. Harris

A solution has been obtained to the problem of calculating flow into a cased and perforated well. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. Computer experimentation indicated that the results are within 3 per cent of the exact solution. Computed results are presented as an apparent skin effect, on a series of dimensionless working curves. Productivity ratios can be rapidly calculated from these data for the wide range of wellbore and reservoir properties actually encountered in field practice. Any reasonable vertical unisotropy ratio can be included in the computation. Productivities can be calculated for wells perforated in a regular pattern, a single horizontal plane or a vertical line on one side of the casing. Solutions for asymmetrical perforation patterns can he easily obtained from the working curves. Solutions for flow into sells completed with a horizontal notch are also provided. Results show that productivity can be increased by extending perforation penetration. This is especially true for shallow penetrations. The highest productivity is obtained when perforations are arranged in horizontal planes, as opposed to a vertical line on one side of the casing. Four or five perforations in one plane will approach the maximum productivity. The effect of perforation hole diameter is small, and is rioticeable only in shallow penetrations. INTRODUCTION The perforating method of well completion has been successfully and widely used in most producing areas. In the past, the desired perforation results were achieved by simply shooting numerous large holes in the casing. A perforating scheme for an area, or particular well, was established by evaluating two types of experimental data: the well flow index and the productivity ratio.' 3 The well flow index test is a means of determining the relative flow capacity of perforations in a linear system. This test also gives information on the perforation size, shape and hole damage which can be expected under well-bore conditions. However, relative flow data from this test cannot be accurately tarnsformed into the radial wellbore system. Thus, no true indication of the productive capacity of a perforated well can be obtained from the well flow index test. A well productivity ratio is derived from electrolytic models built to simulate perforated wells. Available productivity ratio data 2,3 are limited in that all important variables are not extensively evaluated. For example, data are limited to well radii of 3 and 6 in., and to maximum perforation penetration of 1 ft. Practically no information is available on the pattern of flow into a perforation. The effect of various perforation patterns on well productivity has not yet been determined and the effect of perforation diameter has not been thoroughly studied. Also, it will be shown that this type of electrolytic model data is probably in error by as much as 10 per cent or more. Modern completion techniques such as limited-entry perforating, single-plane fracturing, steam and hot air injection and chemical consolidation of incompetent formations all rely on injection and/or production from a limited type of completion. These completions may consist of several high-capacity perforations or a horizontal notch which is equivalent to an infinite number of perforations in one plane. Proper design of these new completion techniques requires, in part, accurate estimates of a well's productive capacity. Data on perforated and notched well productivity have been determined in this investigation. Results are presented as a function of the pertinent variables. Equations describing the idealized system were solved by numerical analysis techniques on a high-speed digital computer. DESCRIPTION OF PROBLEM PRACTICAL APPLICATION The computed results can be applied to wells which meet several general specifications. An external drainage radius of the well must be known or assumed, but the well need not be drilled on a regular pattern. The well must be cased and cemented through the entire producing interval. And, the casing must be perforated with one or more horizontal planes of perforations. The perforation pattern itself must conform to three geometrical requirements. 1. The perforations in a plane must divide the plane into equal angular segments (Fig. 1). Four perforations per plane would be 90" apart. 2. Perforations in a plane must be directly above or beneath perforations in adjacent planes. For two shots per plane, perforations would lie in the BB' plane (Fig. 1). 3. Horizontal planes must have equal vertical spacing and be separated from the top and bottom of the formation by one half the spacing interval. Single planes of perforations should be in the middle of the formation. This is shown in Fig. 2 where h is the formation thickness in a single plane conlpletion or the spacnig interval in a multiple plane completion. The spacing interval at the top and bottom of the formation may vary somewhat without causing an appreciable error in the productivity calculation if the formation is reasonably thick and there are many horizontal planes of perforations. A special provision has been made to calculate the productivity ratios of wells with uneven spacing intervals, or for the case where a single plane of perfora-

Jan 1, 1967

By J. L. Sepulveda, R. F. Yap, R. Jauregui

INTRODUCTION The Third Theory of Comminution, oftentimes called the Bond Theory, was first published by Fred C. Bond in 1952. Since then, it has been widely used in the milling industry to size crushing and grinding equipment as well as to predict and evaluate their performance. Although two other comminution theories were advanced almost a century earlier, one by Rittinger, 1867, and the other by Kick, 1885, their use was limited because they did not agree with actual commercial comminution systems (Bond, 1961). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced in particle breakage, and equals the work represented by the product minus that represented by the feed. For particles of similar shape, the crack tip length is equivalent to the square root of one-half the surface area, and the new crack length is proportional to [(1/vT - vF)]; where P and F are particles diameter of product and feed, respectively. For practical calculations, the particle diameter can be expressed in terms of the 80% passing sizes, P and F, respectively. Therefore, the work input is given by, [10 _ 10', W = Wi [7P_7F(1)] Where W = the energy input to the mill, (kwh/t) Wi = Work Index, (kwh/t) P = square sieve opening which 80% of the product passes, (microns) F = square sieve opening which 80% of the feed passes, (microns) Equation (1) is the mathematical statement of the Third Theory, or the Bond equation. Numerically, the work index is the energy required in kwh/t to reduce a given material from theoretically infinite feed size to 80% passing 100 microns. The work index of a particular material is determined in the laboratory by conducting the standard Bond grindability test. Bond developed separate tests for the rod mill and the ball mill. The simplified test method described in this paper, which is used at Anaconda Research Center to approximate the work index, is an alternative procedure to the ball mill

Jan 1, 1982

By B. Ladanyi, B. Hoyaux

One of the most important problems in underground works is the assessment of the stability of underground openings and the determination of loads on eventual supporting structures. Under certain stress conditions, a hard and sound rock around an unlined opening may show a tendency to rock bursting, which can be prevented by appropriate measures. On the other hand, a less competent rock even if it fails in a less violent manner may give rise to a rock load because within limited regions surrounding the opening, the failed material may have a tendency to flow into the opening; this condition should be prevented by designing a proper supporting structure. The stability of the opening, as well as the value of the design loads acting on the supports in the latter case, depends clearly on the shape, extent, and location of the failed regions, which are often called “plastic zones.” It has been known for some time how the plastic zones develop in some very simple cases, such as in the case of a circular opening in an elastic ideally plastic medium subjected to a nongravitational stress fie1d.l However, to the knowledge of the authors, no information has been available up to now about the extent of the plastic zones in a more general case and for rocklike media. ASSUMPTIONS ON ROCK BEHAVIOR MADE IN THE CALCULATION The solution shown in this chapter is valid for a horizontal tunnel of circular cross section driven through a rock medium at a finite depth.

Jan 1, 1970

By L. R. Jackson

THE idea presented in this paper is that the capacity of a metal for plastic flow before rupture is dependent on the type of stress system applied-that is, the absolute magnitude of the stresses are unimportant provided that they are large enough to produce continued flow; the important factor is the "type" of stress system. A term called the "triaxial stress ratio" is defined in such a way that this ratio can be used to characterize the "type" of system. The paper is divided into three sections. The first section discusses means of representing the effect of complex stresses on plastic flow and defines "triaxial stress ratio"; the second section discusses various methods of' obtaining complex stress distribution. The third section gives some experimental results showing the effect of types of complex stress on the capacity of various metals for flow. An appendix discusses some details on methods of obtaining complex stresses. I. REPRESENTATION OF COMPLEX STRESS SYSTEMS AND THEIR EFFECT ON PLASTIC FLOW Representation of Stresses It is convenient to have a consistent system of notation that will allow the representation of the entire range of complex stresses from hydrostatic compression to hydrostatic tension on plastic flow in a single diagram. Such a system is provided by making use of the fact that any complex stress system can be resolved into a hydrostatic tension or compression and a pure shear. Consider a stress system having the principal stresses [S1 S2 5 S3]. This system can be resolved into a new system consisting of the three components [ ] and three pure shears. If Sm is positive, the net stress effect is hydrostatic tension; if it is negative, the effect is hydrostatic compression. In order to produce a systematic notation, a quantity that will be referred to as the "triaxial ratio" will be defined by the equation [ ] Sm is given by Eq. I and S1 is the absolute magnitude of the largest principal stress without regard to sign. Table I lists the triaxial ratios for various common systems. [ ] Representation of Strains Strains will be plotted as "true" strains according to the system proposed by Ludwik.1

Jan 1, 1944

By Frederick Mark Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and sciences. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By Leonard Greenburg

The American literature in the field of dust sampling and analysis has been growing rapidly since 1915. Studies made since that time clearly indicate that there are three fundamental factors that determine the production of lung pathology due to dust inhalation. These are the duration of exposure, the chemical and mineralogic nature of the dust and the concentration of the potentially harmful dust. In the estimation of the amount of the potentially hazardous dust there are essentially three problems involved: (I) a determination of the size of the hazardous dust; (2) determination of the most satisfactory apparatus and technique of sampling, and (3) the most satisfactory method of analysis. A complete study of the literature shows that industrial dust varies ill size from ultramicroscopic particles to those larger than lop in diameter and that relatively few particles are found over 5u in diameter. Approximately 10 to 25 per cent are less than 0.811 in diameter and the median size as a rule is found to lie between 1.25 and 1.75 microns. From the point of view of lung pathology the particle sizes of most importance lie between 0.5 and 5u. Of all the instruments for sampling dust the Impinger apparatus is the only one that will sample a larger body of air satisfactorily with small control errors and high efficiency in both low and high concentrations of dust. The Owens apparatus has the advantage of being more portable and somewhat easier to use but it does riot permit of the sampling of large volumes of air. It has a low efficiency in high concentrations of dust and does not permit dust weights to be obtained. From the point of dust-counting technique the author points out that in 1922 considerable experimentation with dark field and oblique illumination resulted in the conclusion that such methods were not readily duplicated from day to day and therefore yielded somewhat erratic results. Changes in the amount of illumination produced variations of several hundred per cent in dust counts obtained with dark ground

Jan 1, 1934

By R. E. Ogilvie, N. L. Peterson

DURING the past few years there has been considerable effort devoted to the understanding of radiation effects on materials. The concept of the Frenkel defect and other lattice defects suggests that radiation may alter the rate of many metallurgical phenomena, especially those which are diffusion controlled. In 1953 R. R. Coltman and T. H. ~lewitt' found an appreciable effect on the ordering rate of Cu,Au due to fast neutron bombardment. Since then several rather comprehensive theories have been proposed on radiation enhanced diffusion in solids.2"4 If the energy of the radiation is above the threshold energy for the removal of atoms from their lattice sites, Frenkel defects will be produced. These defects can be produced uniformly throughout a relatively thick specimen by high-energy X-rays permitting bulk property studies without the limitation of sample dimensions. In this work high-purity arsenic containing 30 ppm of impurities was allowed to diffuse from the gase- ous phase at 700°C into single crystals of p-type germanium containing 0.1 ppm of indium. As the arsenic diffuses into the P-type germanium, an n-type layer will form in the diffusion zone. At the p-n junction the concentration ratio of the arsenic to the indium is constant. Experimental Procedures—The germanium specimens, 10 mm by 10 mm by 5 mm, were polished and etched to a mirror finish. The specimens were then sealed off in a vycor glass capsule at 3 x 10"5 mm Hg pressure with a sufficient amount of arsenic powder to produce a one-half atm pressure of arsenic at 700°C. Specimens were annealed at 700°C without radiation. The diffusion coefficient determined from these samples agrees within 8 pct of previous work done by Fuller.' Three specimens were given diffusion anneals at 700°C in a small tube furnace centered beneath the target of a 2-mev Van de Graaff generator. The specimens when in the furnace were 10 cm directly below the target of the generator. These specimens were irradiated continuously during the diffusion run with the Van de Graaff operating at 2 mev with a tube current of 225 to 250 pamp. The intensity of the x-radiation at the surface of the specimen inside the furnace was approximately 4.5 x l05 roentgens per hr. The temperature was controlled within m2°C by a chromel-alumel thermocouple throughout this work with no observed temperature change due to the radiation. By careful lapping, the samples were polished at an angle of 5 deg to the diffusion zone, giving a XI0 increase in the visible diffusion zone. The location

Jan 1, 1960

By A. Ghosh, T. B. King

The kinetics of the discharge reaction: 20'- (in silicate melt) = O,(g) + 4e- at a platinum anode in lithium silicate melts have been studied al 1350°C by galvanostatic methods. Plots of the sleady-state overpotential, q, as a function of the logarithm of the current density, i, showed injlections and were linear only at high current densities. The value of the overpotential was influenced by bubbling gas through the electrolyte. The ocer potential was also studied as a function of time. The rise and decay of overpotential were very slow processes. At low current densities transport is the likely rate-controlling process but at high current densities passivation of the electrode, Presumably by an oxide film on the surface, seems to be a contributory functor. IT is well-established that molten silicates behave as electrolytes'5 and, except in a few cases,6 conduction is entirely ionic. Moreover, it is supposed that a possible, and perhaps predominant, mechanism for phase boundary reactions between metals and slags is similar to that in corrosion whereby anodic and cathodic processes occur at unrelated sites, the metal serving to conduct electrons.1'8 Thus electrochemical studies of some slag-metal reactions would seem to be a useful way to diagnose the rate-controlling steps in the overall reaction. The electrochemical method is, in principle, a better diagnostic tool than the direct chemical method for the following reasons: 1) The partial electrochemical reactions, which are simpler than the overall reaction, may be studied individually. 2) The rate of reaction can be controlled at will and independently of the concentrations of reactants. 3) Fast reactions can be studied by relaxation methods.' Esin and his coworkers5'10"12 have pioneered such studies in silicates and have deviloped some ingenious techniques. Not all of their findings, however. can be accepted without a good deal of further work. In this investigation, the kinetics of the oxygen discharge reaction: 202- (in silicate melt) = Oz(g) + 4e- [I] at a platinum electrode were studied by both steady-state and transient galvanostatic techniques. Interest in this reaction was first developed as a result of the findings of Fulton and chipman13 that the reduction of silica, in a silicate slag, by carbon, dissolved in liquid iron, is a very slow reaction. Subsequent work, for example, by Rawling and ~lliott,'~ has demonstrated that the reaction under these conditions must be slow, because the rate is limited by diffusion of oxygen in the iron to the metal-crucible phase boundary at which a CO bubble may be nucleated. Further work by Tarassof,'~ in which the reduction of silica by aluminum dissolved in copper was studied, has shown that under these conditions, where carbon monoxide evolution is not involved, control of the reaction rate resides in diffusion of silica in the slag phase. However, there is no practical way of inducing sufficient convection in the system to make it clear that the phase boundary reaction is indeed fast. The overall reaction of silica reduction involves the discharge of silicon ions at cathodic sites and oxygen ions at anodic sites. In the examples cited, the discharged ions are dissolved in a liquid metal. In the present study of oxygen ion discharge, gaseous oxygen may be evolved at high current densities or oxygen may simply dissolve, possibly as oxygen molecules, in the silicate at very low current densities. The discharge of an oxygen ion at an anode must, in silicates less basic than the orthosilicate composition, be preceded by a reaction in the vicinity of the electrode, such as: which makes oxygen ions available. Platinum was chosen as the working electrode since it is comparatively inert to oxygen and is, therefore, expected to come rapidly into equilibrium with the electrolyte and with gaseous oxygen. Minenko, Petrov, and Ivanova16 have measured the electromotive force at a platinum electrode in molten silicates as a function of the partial pressure of oxygen in the atmosphere, the concentration of oxide ions in the melt, and the temperature. They found platinum to behave as a reversible oxygen electrode. At two different oxygen pressures, Po2 (I) and Pq (11). the electromotive force is given by: where F is the Faraday constant, equal to 23,060 cal per v equivalent, indicating that the electrode reaction is as written in Eq. [I.]. Platinum has been similarly used in molten silicates by other inve~ti~ators. "'~~ In this investigation platinum was used only as an anode, since a current deposits other elements on its surface and changes its characteristics.

Jan 1, 1970

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By C. A. Heiland

GEOPHYSICAL methods are playing an ever increasing part in various engineering fields. About ten years ago, geophysical exploration was first applied in civil engineering to the study of foundations and the location of construction materials and water. Its usefulness is now being extended into the field of structural engineering. Almost every structure has to be so designed that it will withstand any force to which it may be subjected. Such forces may result from its own weight, applied loads, pressures of various kinds, including those due to wind and water, ground subsidence and vibrations. The last two, problems involving the nature and dynamic behavior of surface and subsurface formations, are within the scope of geophysical investigations. In the design of any structure, the disposition and dimensions of its members as well as their materials must be so selected that they will withstand any or all of the forces enumerated above. In other words, its "resistance" to such forces must be sufficient, allowing for a definite margin of safety. Often a static treatment of the problem leads to satis-factory results, but the static method entails serious errors when vibra-tions are involved, as in resonance with an impressed vibration the displacements of a structure or parts thereof may dangerously exceed the allowable values. The principle of "dynamic design"? is, therefore, avoiding or reducing resonance by suitable selection of the natural frequency of a structure, or by the provision of damping.

Jan 1, 1939

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By William Blauvelt

Tun technical and engineering problems in the manufacture of coke are today the problems of the byproduct oven. Except in a few special localities, practically no beehive ovens have been built in the United States for the last 5 or 6 years except as renewals of old plants, and during these years the total number of beehive ovens in existence has been steadily falling. On the other hand, the number of byproduct ovens has increased from 4624 in 1911 to a total of about 7660 in operation at the end of 1917; with 2800 building, this makes a total of about 10,460 which will be in operation in 1918, or shortly thereafter. Preliminary Government estimates place the total production of coke for 1917 at 56,600,000 tons, the largest tonnage in the history of the industry. Of this 34,000,000 tons or 60 per cent. was beehive, and 22,-600,000 tons, or 40 per cent. was byproduct coke. Some time in 1918 the production of byproduct coke should pass the beehive output, and when the byproduct ovens now building are completed the total byproduct capacity will be about 40,000,000 tons of coke per. annum, which is over 70 per cent. of the record-breaking total coke production of 1917. The reasons for these changes in the coking industry are familiar to all of us, and need not be discussed here.

Jan 3, 1918

By N. S. Keith

No one of the live subjects of the day, to which the attention of the mining engineer and metallurgist should be turned, is of greater practical interest to him than electricity in its applications to various mechanical, chemical, and metallurgical operations. The object of this paper is to call the attention of my fellow-members and associates of the Institute to various new, as well as comparatively old, developments in the science and art of electricity which seem to promise results of advantage. Too many of the comparatively old applications have been neglected by the mining engineer, which; if he had given them a place among his appliances, would have assisted him greatly. The telegraph may be noticed as one. Its. use is, however, confined to a person having skill in the. manipulations of the key, the reading of the alphabet, and familiarity with the sounder. One of the simpler forms-the call-bell-has a range of application far greater as to distance and convenience than the old wire-pull, or the hoarse voice of the windlass-man or the bucket-dumper. A few Leclanehé cells, two or more electric bells, and a mile or more of wire judiciously placed will put the superintendent, at his office, in communication with the foremen of his mills and mines, so that by the aid of a code of signals, great advantages may be gained without necessitating a knowledge of the Morse alphabet, or of the mechanical voice of the sounder. The telephone furnishes a means of communication be-

Jan 1, 1882

By John Naughton

At the General Electric ResearchLabora-tories, we have been interested in the iron-manganese system and the effect of hydrogen on the properties of these alloys. Dr. H. H. Uhlig previously has presented some of these results.' We wish now to offer some other of the data that have a bearing on the subject of this symposium. In the determination of hydrogen in the iron-manganese system by any heating Method we are presented with the problem of the evaporation of volatile manganese and the consequent adsorption of hydrogen by this evaporated metal. It seems wise. therefore, to extract gas at as low a temperature as feasible. Consequently we chose the vacuum or hot extraction method for the analyses of these alloys. The apparatus used is shown in Fig. I. The design is a modification of the apparatus described by Holm and Thompson. To limit loss of hydrogen, samples are stored in a chamber immersed in liquid air. We recommend this procedure whenever there is a question of loss of hydrogen at room temperature. Thence they are moved to the quartz furnace by means of a small magnet, where they are heated by induction to 700' to 800°C. The extracted gas is removed by the circulating pump and placed in the known volume VI (or V2). The circulating pump has been described.3 It is so designed that in spite of the fact that the outlet portion of the pump is part of the known volume, this volume is affected neither by the speed of pumping nor by the pressure of stored gas. The pump also serves to circulate the gases for analysis. The analytical system consists of a

Jan 1, 1945

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

By R. V. Higgins, A. J. Leighton

A fast method is needed for calculating thoroughly the performance of two-phase flobr~ in reservoir rock with complex geotrietry. The authors present such a method and .slzow its accuracy by romparison with laboratory performrrnce of a five-spot pattern. In making the performance c.alculations, the octant of the five-spot pattern was divided into four channels. The computer tinle required for the culculation was one rllinrcte. This is rorighly about minute per channel. INTRODUCTION By using an electronic computer it is now possible to make reservoir performance calculations in which fewer assumptions and more significant variables are included than was possible with a desk calculator. These performance calculations include such variables as the properties of the reservoir rock and its contained fluids, properties of the rock-fluid system and even different well-spacing patterns. Usually, the more variables that are included the higher the computer cost—and time on the computer is expensive. As a result, a short procedure is needed so the many variables will be included and accurate performance calculations will result. If a reservoir is composed of alternate layers of permeable and impervioi~s rock, and if each conducting layer has a different relative permeability, the combined computer cost for calculating each layer by the present long computer programs (which includes different well-spacing patterns and other variables) would be expensive. The performances of complex spacing patterns in a field often are studied by a potentiometric model, but in these model studies the analogy is to the flow of only a single phase. This paper presents a procedure to calculate the performance of a five-spot pattern with two phases flowing using a potentiometric model as a guide for the dimensions of channels and other related data. The time required to calculate the complete performance is about one minute on the IBM 7090 or four minutes on the IBM 704. The procedure can be extended to calculate the performance of more complex well spacings or an entire field with little modification. The procedure has been tested on the performance of the laboratory water floods of a five-spot pattern reported by Douglas, et alThe range of viscosity ratios in the laboratory experiments is from 0.083 to 754, which is extensive. The accuracy of the performance calculations is excellent as shown by the plotted points in Fig. I. The recovery as influenced by the geometry of the five-spot, taking into account the deviation from true radial character, has been predicted by Aronofsky and Ramey." The authors used a potentiometric model to determine the sweep efficiency to breakthrough of the flooding agent. Dyes, Caudle and Erickson,&apos; by means of a laboratory model, show the influence of mobility ratio on recovery after breakthrough of the injected material. Dyes, et ai, used the X-ray shadowgraph technique and miscible phases in their studies. Craig, Geffen and Morse from the analysis of the performance of their laboratory model correlate many variables, including average saturation of a flooding agent determined by permeability relationship. Craig, et al, used X-ray shadowgraphs to determine the sweep efficiencies in sandstone models. In this report the sweep efficiency is not needed, and the important effect of continuously changing saturation gradients before and after breakthrough

By A. S. Nowick, W. A. Goering

INspite of considerable interest in the kinetics of ordering of the alloy Cu3Au there is no direct information available on the activation energy for atom movements in this alloy, such as that obtainable by radioactive tracer-diffusion studies or by internal friction measurements. Accordingly, this alloy was examined to find out whether it displays an internal friction peak resulting from stress-induced ordering, similar to that studied extensively in other alloy systems.1-3 Measurements of the internal friction as a function of temperature were made in a torsion pendulum similar to that described by Ké.8 Wire specimens 0.032 in. diam and 11 in. long were used. The wire, obtained in the cold-drawn condition,* was annealed at 900C in a quartz tube to obtain a large grained sample, and then mounted in the torsion pendulum furnace. Internal friction is reported here as the lag angle, 4, which is equal to the logarithmic decrement divided by .ir. Fig. 1 shows the internal friction at three frequencies (the frequency given for each curve is the value measured at the peak). The data for these curves were obtained on cooling one specimen from 460C to just above the critical temperature for long-range ordering, which is about 390C for this alloy. In this way, the internal friction is measured under conditions where the alloy is in the disordered condition throughout the run. The curves obtained at frequencies of 2.15 and 1.29 cps show peaks in the range of measurement. The corresponding peak for the 0.78-cps curve is estimated, from the shift of this curve relative to the others, to be located slightly below the critical temperature (at 385C). The fact that the peak can be observed above the critical temperature is good evidence for the belief that it is a stress-induced ordering phenomenon similar to that which is observed in other disordered alloys. The fact that the peaks in Fig. 1 are not the same

Jan 1, 1959

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936

By E. W. Henderson

Development work in the state of Utah in 1935 consisted of additional work done on wildcat tests started in previous years and on a number of new wildcat tests started during the year. No effort was made to extend areas or to discover deeper productive horizons in proven fields. Principal areas of development were in Daggett County, northeastern Utah; Grand and Emery counties, east-central Utah; and in Washington County, southwestern Utah. Daggett County Clay Basin.—The Mountain Fuel Supply Co. deepened Murphy No. 2, sec. 21, T.3N., R.24E., from 6030 to 6790 ft. for a test of the Sundance formation. Two sandstone members at 6520 to 6644 ft. and 6737 to 6790 ft. contained water. The hole was plugged back to 5860 ft. and left as a future gas supply for the Salt Lake City-Ogden pipe line. The failure of the Sundance formation to produce in this test, in view of the recent Sundance discoveries in Colorado arid Wyoming, was disappointing Emery County Last Chance.—-Thc wildcat test of the Rainsey Petroleum Corporn-tion, Well No. 1-X, sec. 18, T.26S., R.7E., completed plugging back from total depth of 3168 ft. to 2771 ft. and was shut in as a gas well. A gas sand at 2724 to 2771 ft. produced approximately 21 million cubic fert. A deep test of the structure will be started upon approval of a wit plan of development. Grand County Cisco.—-The wildcat test of the Utah Southern Oil Co., sec. 33, T.22S., R.22E., of which the total depth was 1720 ft. on Dec. 31, 1935, is the most interesting operation ill the state. Location of the test was deter-

Jan 1, 1936