Search Documents

By R. R. Kimpel, L. G. Austin

An equation is derived describing fragment size for single fracture of brittle solids. It contains the equations of earlier workers as special or approximate cases and, in addition, is capable of describing coarse distributions in which a few large particles are produced on fracture. The equation can be fitted well to single fracture experiments where over-breakage is avoided. In 1956 Broadbent and callcottl described a method of analyzing the unit operation of grinding, applicable to homogeneous breakage of brittle materials. In essence, the grinding process was split into two parts: 1) the fractional amount of a given size which is selected for grinding per unit time, 2) the size-weight distribution of the fragments produced by breakage of this certain size (primary breakage distribution function). The theory was formulated using matrix algebra. They attempted an experimental verification of the theory using an assumed primary breakage distribution but the results were not very satisfactory. Austin and Gardner2 showed that this assumed distribution was widely different from experimental values and that it led to the poor agreement of predicted size-weight distributions with experiment found by Broadbent and Callcott. In addition, Austin and Gardner2,3,4 reformulated the original approach in terms of differential equations of grinding and demonstrated that the approach led to a very satisfactory description of the grinding process, providing that the descriptive parameters were measured experimentally. Recent work5 has substantiated these findings and the distribution functions of several materials ground under different conditions in different mills have been determined experimentally. The fraction underweight versus size used by

Jan 1, 1965

By Wilfrid R. Foster

The industrial importance of the sillimanite group of minerals depends upon the beneficial properties exhibited by porcelains and refractories in which substantial amounts of these minerals are utilized as raw materials. The presence of "sillimanite" (now known to be the closely related mineral, mullite) in conventional porcelains and refractories has been known since before the turn of the century. As early as 1906 German investigators observed a direct correlation between the "sillimanite" content of a porcelain and its electrical and mechanical properties. Acting upon this discovery, U. S. Bureau of Standards investigators during World War I developed improved pyrometer tubes and spark plug porcelains, by increasing substantially the amount of "sillimanite" at the expense of quartz. The success of these experiments, first reported in 1918, at once aroused a lively interest in the location of natural sources of sillimanite and its related minerals. As a result of diligent search, the large andalusite deposits in California were discovered in 1919. Within the next several years large deposits of kyanite and sillimanite in India and kyanite in the United States had been reported. The search for these minerals in quantity, by both private and governmental agencies, has continued unabated during the ensuing forty years. A number of domestic deposits of kyanite have been worked during the past 30 years. Of these, only the Virginian and South Carolinian deposits are currently in substantial production. The only commercial andalusite production in the United States has been in California and Nevada. A dumortierite deposit in Nevada, known since 1917 but ignored for want of a commercial use, began production in 1925. A topaz occurrence in South Carolina has yielded a small production since about 1940. Domestic production of andalusite, dumortierite and topaz had virtually ceased by 1950. There has never been any commercial development of domestic sillimanite deposits. Kyanite has been mined almost continuously in India since about 1922. The remoteness of the large deposits of Indian sillimanite had caused it to be neglected until 1949. In that year sillimanite production began, and it has continued to the present. South African andalusite has been marketed from the 1930's until the present time. From 1944 to 1955 Kenya, British East Africa, was an important producer of kyanite. Commercial deposits of kyanite in Ontario, Canada should soon be in production. The first production of kyanite in Europe began in Austria in 1953. No commercial deposits of mullite are known anywhere in the world. It is of interest to note that synthetic mullite, which as "sillimanite" first elicited interest in the A12O3-rich aluminosilicate refractories, has enjoyed a marked increase in production in recent years. This is a result of the gradual depletion of known deposits of high-quality kyanite and related minerals."' Composition The sillimanite group includes kyanite, andalusite, and sillimanite, all having the same chemical composition (A12O3•SiO2) but different physical properties. Two other minerals, dumortierite and topaz, are also included in

Jan 1, 1960

By W. D. Keller

THE high-alumina clays of Missouri are interesting for several reasons. They are the only sedimentary deposits in North America of first grade (over 70 pct A1,0,) diaspore and boehmite sufficiently large to be mined commercially. Mineralogically, they are composed of diaspore and boehmite in intimate coexistence, but gibbsite, the common hydrated alumina mineral in bauxite and laterite, is absent, or is exceedingly scanty if present.* Therefore, the Missouri high-alumina clays do not represent typical laterization. The physical chemistry leading to their mineral genesis, and the geolbgical setting for their formation, present important problems for scientific study. The origin of the Missouri high-alumina clays has been discussed in earlier reports by Allen1 (1935) and McQueen 8, 9 (1929, 1943). These investigations were made under difficult conditions, however, because no diaspore deposit had been opened where a Paleozoic (Pennsylvanian) rock cover lay undisturbed over the high-alumina clay. The relationship of the clay to only the underlying rocks could actually be observed. Lacking the guidance of critical postdepositional geologic evidence, undue and erroneous emphasis was placed on the postdepositional leaching of the deposits in the theories on the origin of diaspore and boehmite from clay (hydrous aluminosilicates) . With new geologic evidence at hand, a clearer picture can be made for the origin of the Missouri high-alumina deposits. In this paper the geology of a diaspore deposit whose original Paleozoic cover had not been eroded will be described and interpreted genetically. The close relationship of boehmite and diaspore (also with kaolinite and a chloritic mineral), will be established. A theory of origin for the high-alumina clays, consistent with the new data, will be postulated.

Jan 1, 1952

By R. K. Adams

The availability of digital computers costing less than $15, 000 makes them economically attractive as versatile research and experiment tools. Several such installations at Oak Ridge National Laboratory have shown that improvements in research productivity and experimental control accuracy can result from the proper application of a small digital computer. However, careful attention must be paid to several potentially expensive problems in 1) interfacing the experiment to the computer and 2) programming the computer. Two specific applications of very small computers to metallurgical testing and research are described. One is a system for data acquisition and precise temperature control associated with a thermocouple testing program, and the other is a system for pulse calorimetry determination of the specific heat of metals over wide temperature ranges and in the neighborhood of metallurgical transformations. The data acquisition system which uses a PDP-8/S computer monitors signals from up to 264 low-level thermocouple signals at two scanning speeds: 10 readings per second for long-term drift data, and 500 readings per second for transient data. The pulse calorimetry system which uses a PDP-8 computer accepts up to 6 signals of 0- to 10-v range and because of a larger analysis program, uses a bulk memory (magnetic disc) in addition to core memory.

Jan 1, 1969

By D. W. Fuerstenau, L. M. Berlioz

In 1957, Charles1 first presented an analysis of a relationship between the energy expended in comminution and the extent of size reduction achieved. Subsequently, Schuhmann extended and interpreted Charles' approach to comminution. According to their analysis, the energy, E, expended in comminuting unit mass of fairly uniformly-sized material is related to the size modulus of the product, k, by where a is the distribution modulus (slope of the log-log cumulative size distribution plot) and C is a constant, which is primarily determined by properties of the solid. If there is any fundamental basis for the E vs k relationship, E must necessarily be concerned with the useful work for the size reduction process and not necessarily the work input, as discussed in detail by Harris.3 Charles and numerous other investigators tested this equation only by relating k to the grinding time, assuming expended energy to be directly proportional to time, but never directly measuring power. In our laboratories, we recently constructed a special batch ball mill with which the power could be accurately determined with torque measuring apparatus.4 With this device, a direct test of the Charles relationship could then be made for ball milling. 5 EXPERIMENTAL A stainless steel mill, 11.5 in. long and 10 in. in inside diam, lined with eight low-silhouette lifter bars, was used for these experiments. The grinding media consisted of 30 kg of single sized, 1-in. diam, stainless steel balls, which occupied about 50% of the total mill volume under static conditions. The void fraction of the static ball load was approximately 0.4, and for the dry grinding conditions used, the corresponding interstitial volume was filled when about 3300 g of the dolomite feed material was present. The 7x9 mesh dolomite used as feed was obtained as a natural, uncrushed product thus as- suring a random distribution of feed particle shapes. Charge weights of 660, 1320, 1980, 2480, 3300, 3960 and 5280 g, which correspond to 20%, 40%, 60%, 80%, l00%, 120%, and 160% of the interstitial load, respectively, were used. Grinding times of 20, 40, 60, 80, 100, 150, 200 and 300 revolutions were considered, with the mill operating at 54 rpm (approximately 60% of critical speed). The tests were made sequentially, in that the size distribution obtained after a certain grinding interval was utilized as the feed for the subsequent period of grinding. Agreement with control experiments where the mill ran continuously for the entire interval was excellent. Torque measurements were made utilizing a Baldwin-Lima-Hamilton SR-4 torque pickup in the manner that has been described previously.3 Standard wet (to obtain the -400 mesh material) and dry sieving procedures were followed using the Tyler full screen series. RESULTS The Gaudin-Schuhmann size distributions obtained in all of these experiments are characterized by distribution moduli (slopes), a, of about 0.66 and are representative of normal dry batch ball milling of a material like dolomite. As an illustration of typical

Jan 1, 1968

By Heinrich Ries

The clay-resources of Colorado are but little known, for the reason that little has been published concerning them, and also on account of the hitherto small demand for clay products in the Rocky Mountain region. At the present day the wares manufactured from clay which are used in Colorado include common and pressed brick, terracotta, sewer-pipe, pottery and refractory articles. Most of these are brought from a considerable distance; but with an increasing demand for such goods in the West and a better knowledge of the available materials, there should be considerable expansion in the clay-working industry of Colorado in the future. The notes here presented are an abstract of those collected by the writer in October, 1896, in a reconnaissance of the clay-bearing formations of Colorado. Clay-bearing Formations. We may roughly divide the clay-bearing formations of Colorado into three groups : 1. Loess and alluvial deposits. 2. Jura-Trias and Cretaceous clays. 3. Tertiary clays. . The loess forms an extensive deposit of large area, though not very thick, extending from north to south across the State, and eastward from the foot-hills. It is generally a very sandy clay, with little plasticity, and is underlain by a gravelly stratum, which determines the workable depth. Clay similar to the loess is found underlying the river terraces in many of the broader valleys, such as those of the Arkansas, Grand River, etc. The Mesozoic formations extend along the eastern edge of the Rocky Mountains, and also occur in some of the deeper valleys tributary to the foot-hill belt. They consist of a great series of interbedded shales, sandstones and limestones of Jura-

Jan 1, 1898

By William Colby

INCREASING governmental control of human activities seems inevitable. Within the present generation railroad rates and the public sale of water, gas and electricity have been subjected to rigid regulation. The field of control is slowly but surely being enlarged, and it is the object of this paper to outline in brief space this tendency toward increased governmental regulation, as far as mineral resources are concerned. Our, dual form of government complicates the problem. We must deal not only with the powers of the Federal Government, but also with those of the individual States. In order to approach this question intelligently we must have some conception of the powers and jurisdiction of the States and the United States, respectively, over mineral lands and mineral production. Starting with the Federal Government we find it never owned any public domain within the States that formed a part of the thirteen original colonies and, for historical reasons, the same is true of Tennessee and Texas. The Mid-Western States were erected out of the public domain which was acquired by the United States through cession from the original States or by purchase from foreign nations. Congress early in the last century adopted a policy of leasing public lands containing lead deposits in a portion of this Mid-Western territory, but later abandoned that policy and disposed of such public, lands, mineral and non-mineral, outright so that they long since have practically all passed into private ownership and become subject to the general jurisdiction of the respective State governments. In the great public domain lying west of the Mississippi River, and in portions of some of the Southern States, the Federal Government adopted a new mineral land policy following the discovery of gold in California. (Acts of Congress of 1866, 1870, and 1872.) The mineral lands within these States, instead of being disposed of on the game basis as agricultural lands, as occurred in the Mid-Western States, were segregated from agricultural lands and sold under special laws intended to encourage mining, giving the miner the free right to locate and work these mineral lands without paying any royalty to the Federal Government. A miner could also obtain at slight expense a complete

Jan 1, 1930

By J. P. Hammond, C. J. Sparks, C. J. McHargue

IN a study of the effects of solid solution alloying on the deformation texture of titanium, an alloy containing 3.8 pct A1 was found to develop a (0001) [1010] texture instead of the texture characteristic of pure titanium.ls2 A short investigation has been made of the change in texture with aluminum content. Alloys containing 0.27, 0.47, 1.05, and 1.43 pct A1 were prepared by vacuum arc melting, using iodide titanium as the base material. Homogenized ingots were reduced 90 pct in thickness by cold rolling. Pole figures were obtained using the usual film techniques. Fig. 1 shows that the change from the tilted to the nontilted (0001) position is gradual. The dashed contour lines in Fig. 1 indicate the extent to which data was collected. The addition of 0.27 pct A1 resulted in a decrease in the transverse spread of basal poles. With increasing aluminum content, the amount of the tilt becomes less and the region of highest intensity takes the shape of a ring about the center of the pole figure. For aluminum contents greater than 1 pct, the (0001) [1010] texture is definitely present—the sharpness increasing as the amount of solute is increased.* It is interesting to note that Williams and Eppel-sheimer9 eported for commercial grade titanium a high intensity region 20" toward the rolling direction from the rolling plane normal in addition to. one 30" toward the transverse direction. Their basal pole figure was similar to Fig. 1, row inree. The observation that the texture changes gradually with solute concentration is similar to the results of similar studies on copper." At the present time these effects are not clearly understood. Acknowledgments This work was sponsored by the Aeronautical Research Laboratory (WCRRL), Wright Air Development Center, under Contract NO. AF' 33(038)-19574. The authors are grateful for the aid received and permission to publish these results.

Jan 1, 1958

By John D. Erickson, Thomas R. Carlson, Milton T. Pana, Daniel T. O’Brian

Computer use in mine planning has evolved from theory to practical application at the Bingham mine of Kennecott Copper Corp.’s Utah Copper Division. Traditional mine planning methods have been combined with computer technology to produce a more realistic calculation of ore reserves and mining plans. The techniques used are not revolutionary but are an expansion of previous mine planning methods using the calculating power of the computer. These methods can readily be adapted for planning use by practical mining men.

Jan 5, 1966

By Arturo M. Morales

INTRODUCTION Manganese carbonates are nodulized by Cia. Mineral Autlan, located in Ongongo in the state of Hidalgo in Mexico. This kiln is fed minus 15 mm material at the rate of 1870 tpd. About 920 tpd is nodulized into a commercial product having a size range of 15 mm to 12 mm. The kiln also produces about 320 tpd of minus 12 mm fines and 40 tpd of chimney dust. Currently, the minus 12 mm fines are being recirculated to the kiln and the chimney dust is not being utilized. It has been found that there exists a market for manganese to be used as feed to the ferromanganese and silicomanganese furnaces. However, a coarse, lumpy feed can only be used in these furnaces. Accordingly, it has been proposed to screen the fines at 6 mm and agglomerate the minus 6 mm fraction along with the chimney dust and suitable binders. This paper presents the results of a feasibility study and test work aimed at producing an acceptable agglomerated product from the kiln fines for use in the ferromanganese and silicomanganese furnaces. Since the agglomerated product will have to be handled and loaded into trucks in the kiln area and transported over long distances, a minimum strength of 200 N is expected to be necessary. They should also have enough initial strength to be stockpiled and result in a minimum of breakage. A third important requirement is that the agglomerates should be resistant to disintegration during combustion. The recirculating fines were to be agglomerated in their original state, if possible, that is, without grinding. This eliminated the possibility of pelletizing as an agglomeration method. Based on a few laboratory trials, the briquetting method seemed most attractive, and a test program was initiated to explore the briquetting process.

Jan 1, 1977

By William P. Blake

Copper Basin in Yavapai county, Arizona Territory, about twenty miles southwest of Prescott, is well named. It is a depressed area, and a region of cupriferous impregnation.* The geologic conditions are simple. The foundation rock is a coarse-grained granite and gneiss, in which soda feldspar predominates. There are also dykes of porphyritic rock, and a large quartz vein containing pyrites. Superimposed on this crystalline foundation, we find heavy beds of mechanically formed rocks, conglomerates, breccias, and sandstones, in horizontal layers cropping along the bed of a creek, and apparently the remnants of a much more extended formation, now denuded and largely carried away by gradual atmospheric erosion. The heavy beds of conglomerate are in many places much broken and tilted up, even standing on edge in large blocks, as if they had been lifted by some great convulsion; but the cause is much more simple, being merely the removal by gradual disintegration and erosion of the softened and decayed granitic rock below. The materials of these sedimentary beds are chiefly fragments of granite, gneiss, and plutonic rocks loosely mingled. They are the chief repositories of the copper-ore, which forms the cementing substance. This copper-ore is the blue and the green carbonate, azurite and malachite, and the ore is so generally spread through the mass of the beds that the blue and the green croppings can be seen at a great distance, particularly after or during a shower of rain, when the colors are extremely brilliant and beautiful. The copper carbonate is not only a matrix and a cementing material for the fragments of rock, but it invests and covers these fragments so that only malachite and azurite are visible. The beds are from three to ten feet or more in thickness, and, although seemingly solid carbonate of copper, rarely contain over 12 or 15 per cent. of that metal. Some portions of the conglomerates are much more highly charged with copper than others, and in places the beds are almost without copper. If a lump of the coarse sandstone

Jan 1, 1889

By C. S. Barrett

Measurements of impact hardness of ß-brass are reported for a wide range of temperatures. Abrupt softening is observed when temperatures are raised above 425ºC, accompanied by abrupt widening of deformation bands in the deformed samples. Current theories of these effects, and of the lack of twinning, are discussed. HARDNESS1 and flow stress2 of a sample of ß-brass at room temperature depend upon the temperature from which the sample is quenched. It is believed that the state of order in the superlattice is responsible for this dependence—not the order within individual domains, which reaches near-perfection during the quench from any temperature, but the size of the domains which is presumed to be a minimum in the hardest samples, those quenched from temperatures near the critical disordering temperature of 468°C. Measurements of impact hardness made over a range of temperatures and microstructural studies of samples deformed both rapidly and slowly over a range of temperatures, reported herein, should be of aid in reaching a more complete understanding of the underlying factors controlling the properties of the disordered body-centered-cubic material and the ordered material. It appears that such data have not

Jan 1, 1955

By W. J. Babyak

The habit planes for hydride precipitation in large grains of alpha zirconium and Zircaloy-4 were determined in specimens containing 161 and 136 ppm hydrogen, respectively. In zirconium, the hydride platelets precipitated on various pyramidal planes inclined to the basal plane at angles ranging from 10 to 50 deg and 75 to 90 deg. Hydrides were most frequent at inclinations of about 20 deg and 90 deg. In Zircaloy-4, hydride plates were inclined to the basal plane at angles vanging from 5 to 25 deg with the predominant inclinatioiz equal to 12 deg; no platelets were found near the prism plane position. In both zircoinium and Zir-caloy-4, hydrides were principally, but not exclusively, parallel to (1011) type planes. When the Zircaloy-4 gmins were subjected to tension stresses of 12,100 psi and 19,400 psi during hydride precipitation, the hydride habit was unchanged except that precipitation favored those habit planes which were inore nearly perpendicular to the stress direction. The stress-orientatioiz effect increased with the magnitude of the stress. THE hydride habit plane in a zirconium has been determined by several investigators. Langeron and Lehr1 in 1956 found platelets parallel to (1010) slip planes. In 1962, Westlake and Fisher2 confirmed these findings and showed that hydride precipitation on twin planes, as reported by Kunz and Bibb,3 was probably due to incomplete removal of worked metal from specimen surfaces. Secondary habit planes, ( 1011) and (1015), were also found by Westlake and Fisher under particular charging conditions where a hydride layer may have existed at the hydrogenation temperature. Most recently, walters4 and westlake5 again observed the (1010) habit exclusively in zirconium. Louthan and hgermans have reported that hydrides precipitate on various ( 101l ) and (112l) planes positioned 31.5 to 90 deg to the basal plane in Zircaloy-2. The present investigation was concerned with the hydride habit in Zircaloy-4 in relation to that in zirconium and the possible change in habit when precipitation occurs under stress. The latter consideration was prompted by the stress-orientation phenomenon originally reported by Marshall and Louthan.7, 8 I) EXPERIMENTAL Materials and Specimens. Chemical analyses of all materials are given in Table I. The zirconium specimen was a 1 by 4 in. section cut from wrought crystal bar that was hot-rolled at 790°C to 0.300 in. and cold-rolled to a final thickness of 0.095 in. All surfaces were mechanically polished and then chemically polished with a solution of H2O, HNO3, and HF (10:10:l by volume) prior to annealing. Grains as long as 0.25 in. were grown by thermally cycling the specimen three times (in 10-5 mm Hg vacuum) between 825" and 1000°C at approximately 125°C per hr. The specimen was isothermally annealed at 825°C for 24, 40, and 120 hr after each cy-

Jan 1, 1968

Discussion of the paper of M. B. YUNG, presented at the Pittsburgh meeting; October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2451 to 2458. T. T. READ, New York, N. Y.-I might .point out that this paper of Mr. Yung's is on a field that is comparatively little known. It is not as well known as the Kochiu tin field, of Yunnan, which is probably the third . in tin output of the world. This field under discussion is considerably further west and the tin which is produced here is, according to Mr. Yung, of somewhat higher grade than the Yunnan tin, and is used by the refiners at Hong Kong to improve the grade of the Yunnan tin. Most of you know that the tin from the Yunnan is shipped to Hong Kong, where it is refined and shipped to Europe. Mr. Yung points out that the Fu Chuan deposits are entirely alluvial and not found in any veins. They .differ in that from the Kochiu deposits, which Leclere says are "nullement alluvionels; leur origéne filonienne est de plus evidentes." Granite is the country rock here; doubtless the tin occurred in veins in the granite, and the deposits have resulted from the disintegration of the granite. This is a country of strong erosive agencies. The country is semi-tropical, and the rainfall is heavy, so that one would naturally expect deep surface erosion of this kind.

Jan 4, 1915

By G. M. Swinkels, A. Vizsolyi, E. Peters

A process is described utilizing ferric chloride leaching followed by reduction of the cupric content to cuprous by cement copper, with CuCl obtained thereafter by crystallization. The residual liquor is cemented with sponge iron to produce cement copper and a copper free ferrous chloride solution. The latter is oxidized in an autoclave with oxygen to regenerate ferric chloride and to precipitate excess iron as a granular, filterable hematite. Cuprous chloride crystals are reduced to high purity metal with hydrogen, while sulphur reports almost quantitatively in residues in the elemental form. Pyrite and molybdenite are not leached. This paper describes the important variables in the process, as well as the deportment of minor elements as silver, gold, selenium, tellurium, bismuth, nickel, lead, zinc, magnesium, etc. An elegant method of isolating silver from CuCl crystals is described, as well as recovery of gold from residues by a chloride reagent The process is described as non-polluting and capable of producing refined copper, ore grade iron oxide, elemental sulphur, and yields of minor metals as good or better than obtainable by conventional smelting, without the use of solvent extraction or electrochemistry.

Jan 1, 1981

By B. M. Larsen, T. E. Brower

An increasing amount of attention is being paid to the possible influence of oxygen, in its several modes of occurrence in steel, upon some of the properties of the metal; but clearly investigations along this line are unlikely to yield significant results until reliable analytical methods for the determination of oxygen have been established. This paper presents some results of a study of an improved Ledebur method which aims to determine a definite portion of the oxygen; namely, that which presumably is present in diffusible form in the solid steel. These more or less preliminary results lead us to believe that the oxygen so determined has some significance; their presentation at this time will, we hope, stimulate discussion of, and focus attention upon, certain rather neglected aspects of the problem. Considerable work has been done recently on methods of estimating inclusions and on the vacuum-fusion method for oxygen; with results which, however, are of somewhat questionable significance. It is commonly presumed that the oxygen in a bath of molten steel in a furnace is present partly as a separate phase consisting of suspended particles of oxides or silicates, partly in solution, the latter being probably the more important. Upon addition of a deoxidizer, it reacts with some portion of the dissolved oxygen and precipitates it as additional suspended particles; the oxygen not eliminated in this way, which remains in solution in the liquid steel, may be regarded indifferently either as dissolved oxygen or as dissolved FeO. When the steel is poured, some of the suspended particles rise towards the surface, others remain trapped in the finished steel, appearing as nonmetallic inclusions in amounts corresponding usually to about 0.01 to 0.03 per cent Oz in the steel. The dissolved oxygen may be partly eliminated as CO during freezing of the ingot, but some remains either in solution or in part precipitated as FeO. Finished steels may thus contain oxygen in several forms: (1) In non-metallic inclusions which are probably quite insoluble in the solid metal at all temperatures; (2) in solid solution which at lower temperatures may be supersaturated; (3) in FeO particles produced by relief of this

Jan 1, 1932

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Stephen C. Blair

Laboratory permeability measurements at elevated pressure and at temperatures ranging from 20º to 150°C have been conducted on samples of Ironton-Galesville sandstone. The purpose of this testing was to identify and characterize important physicochemical processes occurring in association with the injection and withdrawal of heated ground water at the U.S. Department of Energy's Aquifer Thermal Energy Storage (ATES) field site in St. Paul, Minnesota. Results indicate that permeability decreased significantly as temperature was increased and that dissolution of the dolomite and silicate cementing agents and accompanying changes in mechanical properties may occur in the heat storage aquifer at St. Paul. Further, loss of permeability with temperature in laboratory samples may be caused by the change in the mechanical structure of the sample. Tests at ambient temperature to evaluate the effect of particle migration under conditions of reversed flow indicate that this process will not significantly impair formation permeability at the St. Paul site.

Jan 1, 1984

By C. M. Ball

The magnetic concentration of iron-ores has been so often and so widely studied and discussed among the members of the Institute that any remarks concerning its general importance, from an economic standpoint, would be superfluous; but it is thought that a description of the Ball and Norton ore-separator, designed for cobbing and separating magnetic iron-ores, indicating its essential differences from other machines and the advantages claimed for it, together with some account of recent results obtained in its application to the concentration of such ores, will prove of interest. This machine is the joint invention of Mr. Sheldon Norton, of Hokendauqua, Pa., and the writer, and has been patented in the United States, Canada, and other countries. Of the accompanying illustrations, Pig. 1 represents a longitudinal vertical section of the perfected ore-separator, adapted for separating fine ore, and Fig. 2 the same, adapted for cobbing ore of the size of stove- or chestnut-coal. The two designs are identical in principle, and vary from each other in minor details only. The apparatus consists of a partially-closed chest, having an opening at f, from the feed-hopper, h, through which the ore is delivered to the machine from an ore-pocket or storage-bin provided with means for regulating the flow of ore, so that, when the machine

Jan 1, 1891