Search Documents

By S. K. Basu, H. H. Kellogg

THE physical-chemical behavior of the system Pb-S-0 is of prime importance to the understanding of lead smelting processes, yet little accurate information is available on either equilibrium or kinetic behavior in this system. This paper is the first report of a program designed to fill gaps in our knowledge of this system. In the total ternary Pb-S-0, the region of greatest metallurgical interest is that bounded by the compositions Pb-PbS-PbS0,-PbO-Pb. Systems richer in sulfur, or richer in oxygen,* than those essentially pure SO2. This conclusion follows from the fact that all systems are in a highly reduced state, since either PbS or Pb is a constituent of all the equilibria. The content of 02, SO3, S2, S6, S8, and so forth, can be shown to be negligible compared to SO, in all such systems.* corresponding to this region can only be obtained at gas pressures exceeding 1 atm, a condition seldom met in lead smelting practice. Not only is the present study limited to condensed phases within this portion of the total system, but it is limited to temperatures at which all phases are pure solids, except for lead, which is liquid. In this limited system the following seven condensed phases are known to exist: Pb(l), PbS(c), PbO(c), PbSO,(c), PbSO,•PbO(c), PbSO4 • 2PbO(c), and PbSO, -4PbO(c). PbO exists in two crystal modifications,' but only the high-temperature yellow form is considered here. Schenck and co-workers2-4 reported the compound PbSO4 3Pb0 to be stable at high temperature, but the more recent work of Lander,5 and the present work, prove that the tetra-basic sulfate, rather than the tri-basic sulfate is stable. Fig. 1 shows the composition diagram for the binary PbO-PbSO2, based primarily on the work of Lander. In this study the univariant boundaries and invariant points existing among these seven condensed phases and the gas phase have been determined. In a ternary system, the phase rule indicates that an invariant point involves the simultaneous equilibrium of five phases—four condensed phases and the gas phase. A univariant relation involves four phases—three condensed phases and the gas phase. The gas phase in the systems studied is The following stable univariant equilibria between SOz and the condensed phases were identified: (a) PbS + 7PbS04 = 4(PbSO, - PbO) + 4SO2 (b) PbS + l0(PbS04 • PbO) = 7(PbSO4- 2PbO) + 4SO2 (c) PbS + 8(PbSO4 • 2PbO) = 5(PbSO4 . 4PbO) + 4SO2 (d) Pb + PbSO, • 4PbO = 6PbO + SO2 (e) 3PbS + PbSO4 . 4PbO = 8Pb + 4SO2 (f) 3PbS + 16(PbS04 PbO) = 7(PbSO4 . 4PbO)+ 12SO2 (g) 2PbS + PbSO,2PbO = 5Pb + 3SO2 (h) Pb + 3(PbSO4 . 2PbO) = 2(PbSO,. 4PbO) + SO, Of these eight univariant equilibria, five were measured in this work (a, b, c, d, and g) and the behavior of the other three (e, f, and h) was calculated by thermodynamic analysis of the measured data. Two invariant points were found corresponding to simultaneous equilibria as follows: Point 1: PbS, PbSO4PbO, PbSO4.2PbO, PbSO, - 4PbO, and SO2 Point 2: Pb, PbS, PbSO, . 2PbO, PbSO, - 4PbO, and SO2, From the measurements it was also possible to calculate the thermodynamic properties of the three basic sulfates of lead at 298.16°K. EXPERIMENTAL Apparatus—The experimental method consisted of the measurement of the gas pressure exerted by a given reaction mixture at a given temperature. An iridium crucible was used to contain the reaction mixture. There was no evidence of attack of the iridium,* but after use at high temperature for a week

Jan 1, 1961

By E. P. Pfleider, W. G. Pariseau

Even as the rational selection of excavation equipment requires a matching of machine performance capabilities to rock response characteristics, the functional features of transportation systems must be matched to the characteristics of the materials handled in order to secure optimum, trouble-free operation. In particular, ore passes and chutes must be designed for flow in order to insure controlled draw whenever a chute is opened. The alternative to quantitative design is, of course, the well known ad hoc procedure of freeing plugged ore passes, cleaning up spillage from flooded chutes, etc., after installation of the system. Since the voluminous empirical work sporadically undertaken through the years evidently had not led to reliable design methodology, it seemed worthwhile to attempt a rational and complete description of the movement of material through ore passes. The concepts of de- formable body mechanics applicable to gravity-induced flows of granular media or "soils" were involved. Accordingly, the mathematical theory of soil plasticity was adopted as a working hypothesis, and a two-dimensional laboratory model of an ore pass constructed in order to investigate the appropriateness of the theory. The general experimental strategy consisted of formulating the movement of material in ore passes as a boundary value problem in soil plasticity, determining the required boundary values of stress and velocity experimentally, and then using these data for the initiation of a theoretical solution for stress and velocity throughout the moving mass of material. A comparison between the theoretical and experimental constituted the test of the original hypothesis.

Jan 6, 1968

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By John Chipman

The concentration of a solute in a dilute ),zetallic solution may be measured by any of several parame- ters including weight percent, atom fraction, atom ratio, and lattice ratio. The ratio of filled to unfilled interstitial sites is useful for interstitial solutes. A variable 2 proportional to this ratio is used as a measuve of concentration. For component 2 irz a bitzary solution z2 = n2/Ym - nz/b) where b is the numberber of interstitial sites per lattice atom. For a t~lul-ticortzporzent solution this becomes zz = n2/(nl + Cvjnj) in which Vj = - l/b for an interstial solute and +1 for a substitulional solute. In the infinitely dilute solution the activity of an interstitial solute 2 is proportional lo z2. At finile concentration the departure from this limiting law is expressed us an activity coefficient, his coefficient is a function of concentra1io)z expressed as tevactiolz coeffcient 8; is analogous to the jark~iliar e£ bul is found to be independent of concentvation in certain solutions for which data are available. It is found that the same equations may be used to express the activity of a nonmetallic solute, sulfur, in liquid solutions of iron containing other solutes, both metallic and nonmetallic. For a nonmetallic solute or for one which strongly increases the actiuity of sulfur, it is convenient to assign arbitvarily a value vj = — 1. When this is done the derivative is found to be constant in each of the ternary solutions studied. The activity coefficient of sulfur in a complex liquid iron solution may be expressed as where nk is a second-order cross product determined in the quaternary solution Fe-S-j-k. The equation is used to calculate tlze activity of sulfur i)z three sevetl- component solutions. IN thermodynamic calculations concerning dilute solutions it is unnecessary to invoke laws and relations which extend across the concentration range to include concentrated solutions. In most binary metallic systems, as arkeen&apos; has recently pointed out, there exist two terminal composition regions of relatively simple behavior, connected by a central region of much greater complexity. When the solute is a nonmetal there is only one such region and in many systems the concentration range is extremely limited. It is the purpose of this paper to suggest a method for the calculation of activities in such a terminal region in which one or more solutes are dissolved in a single solvent of predominantly high concentration. HENRY&apos;S LAW In the usual textbook statement of Henry&apos;s law, concentration is stated in mole fraction. This has the advantage that it makes Henry&apos;s law thermodynamically consistent with Raoult&apos;s law. Since all measures of concentration at infinite dilution are related by simple proportion it follows that mole fraction, molality, atom ratio, weight percent, or any other unit of concentration can be used with the appropriate constant. At finite concentrations, however, calculations based on the law depend upon the unit employed. Deviations from Henry&apos;s law at finite concentrations depend upon the composition variable employed. They are evaluated in terms of activity and interaction coefficients2 which have become familiar features of metallurgical thermodynamics. It is the purpose of this paper to propose a measure of concentration for metallic solutions containing interstitial or nonmetallic solutes by means of which the calculation of activities in complex solutions may be simplified. The discussion will be restricted to free-energy interaction coefficients3 typified by Wagner&apos;s c|a BINARY SOLUTIONS The several measures of concentration which are to be considered are shown in line a of Table I. The corresponding activity coefficients are in line b and the deviation coefficients, sometimes called self-interaction coefficients, are in line c. Henry&apos;s law simply states that the activity coefficient approaches a constant value at infinite dilution. By adoptihg the infinitely dilute solution as the reference state and defining the "Henrian" activity as equal to the concentration in this state, the activity coefficient is always unity at infinite dilution. This convention is far sim~ler and more useful in dilute solution than emploiment of the &apos;Raoultian" activities and it will be used in the following discussion. The several definitions and equations of Table I will be referred to by means of their coordinates in the table. Early observations of deviations from Henry&apos;s law in metallic solutions were shown graphically4 rather than analytically. For the case of sulfur in liquid iron5 the slope of a plot of logfs vs (%S) was constant in the range 0 to 4.8 pct S, indicating constancy of eh2&apos; in Ic. He was proposed by wagnerz and has been widely adopted. The a function of IIIc recently employed by ~arkenl was designed specifically for dilute solutions. Darken has shown that the value of a12 remains essentially constant for many binary solutions within a substantial range of compositions. The atom ratio is directly proportional to the molalitv.<, a conventional measure of concentration. IVb and C served as the basis for smith&apos;s6 classic studies of

Jan 1, 1968

By P. Barnes

Several interesting and important considerations may be based upon an analysis of the cost of producing Bessemer rails, and the facts thus set forth may be much more clearly emphasized by re ducing each item of cost to its own fractional proportion of the sum total in each branch of the manufacture. The estimate given below is not absolutely complete in minute ness of detail, but it may be fairly taken as a basis for the suggestions to be noted : Perhaps the most striking comments that can be made upon this statement are those arising from a consideration of some of the smaller items, and even the least of these quite loses its insignificance when its proportion of the whole is expressed in actual money, as for the work of a year, or even for a single day. Thus, if the item as be considered, the importance can be clearly

By Forbes K. Wilson

"For his vision, determination, dedication, and leadership in the conquest of the remote and rugged Ertsberg and the technical and human barriers to its development and for his lecture ..." It is a great honor for me to be included among the Jackling Award recipients, many of whom have been close friends and associates. My subject is the development of the Ertsberg, a copper mine located 4&apos; south of the equator, 70 miles (113 km) from the south coast of Irian Jaya---the easternmost province of the republic of Indonesia at an elevation of 12,000 ft (3658 m) in an area which was inhabited by a few "stone age" people when I first arrived there in 1960. Persistence, tenacity, immagination and innovation were all required to bring the Ertsberg into production. The technical, financial and political problems that have been faced over the past 16 years were unique in many respects. I hope that my paper will give some encouragement and help to future developers of mines in difficult and inhospitable surroundings.

Jan 1, 1978

By D. L. Blakeman, Trimble. J. W., S. W. Banning

Noranda&apos;s Grey Eagle mine and mill, in the Siskiyou Mountains of northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mineralogy, milling, and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1986

By W. L. Austin

At the Steptoe metallurgical plant, where ore of the Nevada Consolidated Copper Co. is beneficiated, a small copper-leaching annex has been in operation treating flue dust from roasting-furnace dust chambers, together with a siliceous oxidized ore. This leaching plant was designed to obviate smelting low-grade siliceous flue dust, which interfered with the operation of the reverberatories by forming a blanket on the charge. The major portion of the copper content of the flue dust accumulating in the upper chambers of the roaster flue, and at the stack, is water soluble, and also contains much free sulphuric acid and soluble sulphates. It was found that sufficient acid could be obtained by mixing this material with water to provide a lixiviant for leaching the siliceous copper ore mentioned. This was the sole source of the lixiviant used in the operation to be described. An analysis of the flue dust showed it to be composed as follows : Per Cent. Copper.............................................. 3.00 siO2................................................. 23.41 Fe................................................... 4.08 CaO + MgO......................................... 2.72 Al203................................................ 0.07 Free H2S04........................................... 19.94 SO3 combined as sulphate.............................. 25.10 H2O combined with the sulphates....................... 10.67 0................................................... 2.50 Total................................... 97.49 Copper soluble in dilute H2SO4.......................... 2.56 The oxidized ore, locally known as carbonate, has the following composition:

Jan 1, 1915

By R. R. Sayers

VENTILATION may be defined as the process by which vitiated air of an inclosed or partly inclosed space is continuously replaced by fresh air. Fresh air has been defined as invigorating pure air. Pure dry air at sea level contains the following gases:1 Analysis of Air at Sea Level PER CENT. Oxygen 20.94 Nitrogen 78.09 Carbon dioxide 0.03 Argon 0.94 Helium, krypton, neon, xenon, hydrogen, hydrogen peroxid, ammonia, ozone traces CARBON DIOXIDE LIMIT For many years carbon dioxide was used as an index of the purity of the air vitiated by the metabolism of people. It was, however, well known that the untoward effects produced on those exposed to such air was not due to the concentration of the carbon dioxide. It has been found that the untoward effects on the comfort and efficiency of those so exposed are due to the increased temperature and humidity. It has been found that men can breathe air containing many times the amount of carbon dioxide found in our worst ventilated theaters and assembly halls, which, according to Rosenau, do not contain above 0.5 per cent. carbon dioxide.

Jan 7, 1926

By G. R. Speich, Morris Cohen

The growth rate of bainite has been determined by hot-stage metallography in five hypereutectoid high-purity iron-carbon, iron-carbon-chromium, and iron-carbon-nickel alloys. The studies have been confined essentially to lower bainite. The growth rate is independent of time at constant temperature, but both the edgewise and sidewise growth rates increase with increasing temperature. Increasing the carbon content, or adding chromium or nickel, decreases the growth rate without greatly affecting the temperature dependence. The results lead to separate diffusion-controlled models for the edgewise and sidewise growth rates. ALTHOUGH bainite has been subject of many detailed investigations,1,2 the growth mechanism of this intermediate transformation product of steel remains unclear. One difficulty has been that practically all the kinetic measurements have been restricted to studies of the overall reaction rate. Only a limited amount of information3, 4-6 is available on the growth process itself. The purpose of the present work was to investigate the effect of time, temperature and composition on the growth rate of bainite using hot-stage metallography. This method makes it possible to observe continuously the isothermal growth of individual bainitic units because of the surface upheavals accompanying their formation.3 This information is needed to test the existing growth models and to obtain a better understanding of the factors controlling the bainitic transformation. EXPERIMENTAL PROCEDURE Alloys—The compositions of the alloys used in the present work are shown in Table I. The five alloys were vacuum-melted and cast, and were prepared from high-purity materials. The three iron-carbon alloys were available from the work of Roberts et al.7 in the form of 3/8-in. diam rods.* To facilitate machining, the rods were ing. The rods were then tempered for 3 hr at 650°C to allow machining. The iron-carbon alloys in Table I were selected for investigating the effect of carbon on the bainitic growth rate. Due to the rapidity of the transformations involved, it was not feasible to measure the growth rates in iron-carbon alloys having carbon contents much less than 0.9 pct C. The iron-carbon-chromium and iron-carbon-nickel alloys were selected to study the influence of chromium and nickel on the growth rate at a carbon level of about 1.1 pct C, since this carbon content was intermediate among the iron-carbon alloys. The concentrations of chromium and nickel were chosen to match isothermal trans formation diagrams in the literature.8&apos;9 Hot-Stage—Since the iron-carbon alloys had such low hardenabilities, it was necessary to quench the hot-stage specimens drastically from the austentiz-ing temperature to the isothermal transformation temperature to prevent the formation of pearlite or proeutectoid constituents. A rapid-quenching metal-lographic hot-stage was built for this purpose. A maximum temperature of about 1100°C and quenching rates up to 500°C per sec could be attained with this equipment. The details of the apparatus are described in a recent publication. After being polished and mounted on the hot-stage, the specimen (0.020 in. thick) was protected from oxidation and decarburization during austenitizing by a vacuum of 10-4 to 10-5 mm. The quench to the reaction temperature was accomplished with a helium blast, and the isothermal run at this temperature was conducted in a helium atmosphere. A fine-wire thermocouple spot-welded to the sample and a high-speed

Jan 1, 1961

By J. F. Kemp

PAGE I. Introduction,.......269 11. Topogmphical Features,.....270 III. Geological Relations of the Mineralized Area,.272 1. Structural Features,.....272 2. Occurrence of the Copper,....274 3. Granite-Contacts,.......274 IV. Descriptions of the Rocks,.....274 1. Granite,........274 2. Limestone,.......276 3. Porphyritic Eruptions,.....278 (a) Quartz-Porphyry,.....278 (b) Trachyte-Porphyry,.....280 V. Contact Phenomena,......285 1. Comparative Immunity of the Limestone, . 285 2. Contact Phenomena in the Quartz-Porphyry,.... 285 3. The Form and Distribution of the Ore-Bodies,290 VI. Method of Deposition,......293 I. Introduction. The White Knob copper-deposits are situated about three miles south of Mackay, on the Salmon River branch of the Oregon Short Line Railroad, in Custer county, Idaho. An outline-map of this district is given in Fig. 1. The deposits have been known and spasmodically worked for many years, and a total of over 3.5 miles of tunnels, shafts and other workings has been driven with a view to their development. These extensive excavations have exposed the deposits sufficiently to permit a careful geological examination. The peculiar features which give special interest to this paper are the branching, tree-like form of the ore-bodies; the absence of zones of secondary enrichment in the partly oxidized pyritic deposits, and the fact that while the deposits are associated in a general way with the contact of an eruptive rock with limeetone, which it penetrates, the garnetization has taken place not in the limestone, as is the usual case, but in the igneous

Jan 1, 1908

By D. C. Holloway

Ceramic projectiles made from 94% to 99% alumina with a nominal mass of 3.1 gms were fired into granite blocks. The average compressive strength of the ceramic was 800 MPa and that of the rock was 135 MPa. Flat, ogive, conical and pyramidal nose shapes were evaluated at velocities ranging from 450 to 1400 m/sec. It was found that the conical and pyramidal nose shapes at the higher velocities did a significant amount of damage to the rock. On the average, they removed 10 5mm3 of rock and were six and ten times better than the flat and ogive nose shapes. It was also observed that increases in volume occur in discrete steps. This process is highly dependent on the ability of the projectile to penetrate the rock.

Jan 1, 1984

By Harry Seltz, J. C. DeHaven

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By J. C. DeHaven, Harry Seltz

InteRmetallic compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dissociated in the liquid state, as indicated by the continuous form of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455&apos; C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a = 6.52, b = 8.60, c = 4.16 A.&apos; There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO² = CdO + CO + Sb From the known free energies of formation of CdO, CO² and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell reaction is the reversible formation of the compound from the elements. The first method is generally applicable, but requires elaborate experimental equipment. The second method can not be used for compounds melting at low temperatures, owing to the difficulty in establishing equilibrium. The electromotive force method, therefore, seemed to offer

Jan 1, 1935

By Russell Dayton

THE metallurgical polarization microscope has been utilized in several researches in the last few years, thus attaining a fair degree of prominence, but little has been written in a manner suitable to a metallurgist concern-ing the theory of this instrument. In this investigation the theory was carefully studied, and the results are presented here in a detailed manner, yet as simply as possible. The theory is discussed with particular reference to the three chief functions of the instrument: (1) determination of anisotropy; (2) effect of strain; and (3) identification of inclusions. Each of these is investigated experimentally, with especial attention to the mechanism of producing any effect. Where possible, the discussion is supplemented by photomicrographs. The instrument used had numerous defects as a polarization microscope; these and their remedies are discussed. In the microscopic study of transparent mineral sections (chal-cography) the use of polarized light has aided tremendously in the identification of a mineral. The determination of strain in transparent substances (photoelasticity) by the use of polarized light has lately become a commercial process, used in testing finished glass articles. The success of the use of polarized light with opaque materials has not been so great. The magnitude of the effects obtained is much less than that of the corresponding effects with transparent materials, and the mechanical difficulties are much greater. Konigsberger,(1)? in 1909, was the first to apply polarized light to the microscopic study of

Jan 1, 1935

By P. A. Beck

ACCORDING to a recent hypothesis of Sully,&apos; xY. binary CT phases are characterized by 1.7 bonding 3d electrons per atom, which completely fill the first Brillouin zone. This hypothesis appears to imply that there are no empty 3d orbitals in the u phase, and that, correspondingly, this phase must be dia-magnetic, or at most weakly paramagnetic. On the other hand, Bowen and Hoar&apos; reported that a u phase extracted electrolytically from an alloy steel became ferromagnetic when cooled to about —113°C. In view of the fundamental interest of the problem from the point of view of the electron structure of the u phase, it seemed worthwhile to study the magnetic properties of massive u phase specimens of various known compositions. Sigma specimens of the following compositions were tested: 1—40 atomic pct Fe, 40 atomic pct Cr, and 20 atomic pct Mo 2—35 atomic pct Fe, 35 atomic pct Cr, and 30 atomic pct Mo 3—48.7 atomic pct Fe, 50.2 atomic pct Cr, and 1.1 atomic pct W 4—40.7 atomic pct Co and 59.3 atomic pct Cr All specimens were found to be strongly paramagnetic at room temperature, particularly alloy No. 1. At liquid nitrogen temperature, alloy No. 1 be- came ferromagnetic; the other u alloys remained paramagnetic. Even though apparently not all u alloys become ferromagnetic at liquid nitrogen temperature, in view of their strong paramagnetism it is probable that the electron structure proposed by Sully is not correct. Similar qualitative studies were made with the p, P, and 8 phases." A p phase specimen of 57.2 atomic pct Co and 42.8 atomic pct Mo; a P specimen of 19.9 atomic pct Cr, 37.8 atomic pct Ni, and 42.3 atomic pct Mo; and a 8 specimen of 50.4 atomic pct Ni and 49.6 atomic pct Mo were tested at room temperature, and all were found to be paramagnetic, although considerably weaker than the u phase specimens described above. A test at liquid nitrogen temperature gave similar results for all specimens; none became ferromagnetic. Thanks are due to D. K. Das for preparing several of the alloys and to Pol Duwez of California Institute of Technology for kindly loaning four specimens of cr alloys. References 1 A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, p. 173. - K. W. J. Bowen and T. P. Hoar: Low Temperature Ferromagnetism of Sigma Phase in an Alloy Steel. Research (1950) 3, p. 484. 3 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951).

Jan 1, 1953

By Earl S. Bardwell

The determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. &apos; The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. The Effect of Annealing Temperature on Physical Properties For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows: Bar Number 1 2 3 4 5 6 Copper + silver...... 99.95 99.92 99.945 99.94 99.95 99.93 Oxygen.............. 0.041 0.070 0.046 0.050 0.036 0.058 As + Sb............. 0.0038 0.0038 0.0038 0.0038 0.0031 0.0031 The bars were heated in an electric muffle to about 1,650" F. and rolled into rods. The rods were annealed, pickled, and drawn to No. 12 B. & S. gauge wire. The wire which was to be used for the annealing test was cut into 38-in. lengths and each length made into a coil 6 in. in diameter. The separate coils were marked so that they might readily be identified

Jan 1, 1915

By R. H. Doremus

From measurements of carbide precipitation rates in a iron it was concluded that the carbides nucleated on dislocations in both strained and unstrained samples, except for the latter at lower temperatures and higher carbon concentrations, where there were more muclei than could form on the dislocations. The equation of Cottrell and Bilby for the segregation of atoms to dislocations was found to be inapplicable to this system. No satisfactory theory for the growth process is available. A study of the rate at which a second phase separates from solid solution can frequently reveal much about the mechanism of separation. There are still many features of the precipitation of carbon from a iron that are not understood, although this system has been examined extensively. To provide more insight into the mechanism of carbide precipitation in a iron, rates of this process were measured at different temperatures, carbon concentrations, and densities of dislocations in the iron. The concentra- tion of carbon in solution was followed from the height of the internal-friction peak; this height is directly proportional to the amount of carbon in solution and is not affected by the growing carbide particles. In this paper these rates are compared with those found by earlier investigators, and the mechanism of precipitation is discussed in light of these results as well as two earlier studies1, 2 and the electron microscopic work reported in the preceding paper. EXPERIMENTAL The amount of carbon in solution was followed by

Jan 1, 1961

By M. E. Wadsworth, A. E. Lewis, R. L. Braun

Experimental results obtained in laboratory leaching studies of primary copper sulfide ore in sulfuric acid systems pressurized with oxygen are interpreted by a computerized geometric model involving the movement of a reaction zone through the ore fragments. Physical properties of the ore, including size, shape, and mineral content, are considered. The leaching mechanism involves mixed kinetics and includes a surface reaction within a moving reaction zone plus pore diffusion of dissolved oxygen through the reacted portion of the ore fragment to the reaction zone. The results are applicable to conditions that would exist in nuclear solution mining or similar processes in which the ore is converted into rubble and then inundated by a leach solution adequately supplied with oxidants. Experimental results at 90°C are correlated with the model, which includes temperature-dependent parameters.

Jan 1, 1974

By J. C. Reed, P. J. Shenon

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935