Search Documents

By G. A. Josey, T. P. Floridis

INFORMATION on the effect of alloying elements on the solubility of sulfur in solid iron alloys is limited to the effects of carbon,' manganese,' and Silicon.Refs. 3 to 5 provide information on the combined effects of silicon and manganese also. In the investigation reported in this communication, the effect of chromium, copper, nickel, and vanadium on the solubility of sulfur in solid iron was determined at 1000". The specimens for this investigation were prepared by melting electrolytic iron and reagent-grade alloying additions in an induction furnace under an argon atmosphere. The melts were allowed to solidify in

Jan 1, 1969

By C. H. Stewart, R. A. Fagin

A two-dimensional, three-phasereservoir simulator was programmed for a large memory digital computer. It was designed to provide a practical solution to describing the complex physical relation between the natural forces and the physical properties of a heterogeneous reservoir when subjected to a specific set of conditions. A reservoir study is briefly described to illustrate application of the model. A full volumetric account of three phases (oil, gas and water) is performed simultaneously throughout an integration net representing the reservoir. Absence of one or two of the phases is treated as a special case of the more general situation. Expansion (or contraction) of all phases, including rock expansion, is performed so that the pressure calculation is the general unsteady-state case. To account for the large variations of subsurface elevation encountered in some reseruoirs, and to allow for segregation of the various phases, a gravity head term is included in the basic drive potential. Appropriate fluid and rock properties are used in polynominal surface form (functions of pressure and/or depth) or they can be entered as space variables at each position of the integration net. An unsteady-state water influx calculation, based on the method of van Everdingen and Hurst, l was connected to the boundary of the matrix to simulate aquifers of various sizes. In addition to reservoir calculations, three-phase fluid flow from the producing depth to the wellhead, including provisions for gas lift, was incorporated in the simulator. A workover routine was also built which can automatically switch to a different set of production relations when a gas-oil ratio or water fraction reaches a limit; or it can shut-in the well if prescribed. INTRODUCTION This paper describes a reservoir engineering mathematical simulator used to represent the complex interaction of natural forces and physical properties of a reservoir during natural depletion or with various injection schemes. The simulator, which was programmed for a large memory digital computer, is a two-dimensional calculation which handles three mobile fluid phases simultaneously (oil, gas and water). Basic requisites for the method are individual well production and pressure data, hydrocarbon fluid properties, geological data (producing depth and net sand), capillary pressure data, relative permeability data and permeability and porosity information. Matching the past performance of a combination drive reservoir often has yielded information concerning continuity and the validity of basic data. Detailed predictions of future performance can be made for continuation of current depletion methods (natural depletion) as well as for various types of recovery by gas or water injection. Combination injection cases and pattern studies can also be performed. Workover programs, gas lift and different types of artificial lift programs have been investigated using a technique similar to that described by Kern and Nicholson2 except that conditions of pressure and saturation at the block within which the well is located are used rather than average reservoir conditions. Drilling additional wells to optimize profit was explored, both as to number and location, by placing wells at different spots within the reservoir matrix. Special depletion processes can be examined, such as upstructure drainage and lateral (or strike) waterfloods in thin oil columns. In one case the mathematics of the simulator were modified to calculate the displacement in the vertical plane rather than in the horizontal plane. In this manner specific reservoir problems can be studied, such as coning of gas and/or water around production points, fingering along permeable stringers or, more generally, frontal advances in a heterogeneous section.

Jan 1, 1967

By A. E. Jenkins, A. Jostsons

Isothermal sections of the Ti-0-H phase diagvam at 600°, 700°, and 800°C have been constructed from equilibrium hydrogen pressure measurements over a range of Ti-0-H alloys containing up to 34 at. pct 0. Oxygen reduces the hydrogen solubility at fixed hydrogen pressure but increases the terminal solubility in the a solid solutions at the a/(a + P) phase boundary. Metal-lographic studies of alloys annealed below the eutectoid temperature show that oxygen also increases the ter-ninal solubility of hydrogen in the a solid solution in equilibrium with the hydride phase. The effect of oxygen on hydrogen solubility is discussed in terms of the electronic and geometric structure of interstitial solid solutions. THE isothermal solubility of hydrogen in a Ti-0 alloys at 800°C has been measured by Hepworth and ~chuhmann' who subsequently used ternary Gibbs-Duhem integrations to calculate oxygen activities in binary Ti-0 alloys. The present study aims to extend Hepworth and Schuhmann's measurements to alloys richer in oxygen and to a range of temperatures. This paper presents the results of hydrogen equilibrium pressure/concentration measurements in Ti-0 alloys as well as observations on the effect of oxygen on the terminal solubility of hydrogen in a titanium. The thermodynamic properties of binary Ti-0 alloys, derived from these measurements, will be published separately.' EXPERIMENTAL METHODS Specimen Preparation. Ti-0 alloys were prepared from iodide-refined titanium and titanium dioxide obtained by hydrolysis of redistilled titanium tetrachlo- ride. Specimens containing up to 16 at. pct 0 were prepared by electromagnetic levitation3 whereas a conventional tungsten arc furnace with a water-cooled copper hearth was used to melt oxygen-rich alloys. The specimen homogeneity was indicated by the constancy of lattice parameters of samples from various parts of the ingot as well as by the sharpness of the reflections on X-ray powder patterns. Oxygen-rich specimens in the composition range (20 to 34 at. pct), where ordering has been ~bserved,~ were annealed for 300 hr at 600°C prior to use in hydrogen solubility measurements. Apparatus. The hydrogen pressure/concentration measurements were made with a modified Sieverts apparatus shown diagrammatically in Fig. 1. Specimens were placed in a clear silica tube and impurity pickup by direct reaction with silica was prevented by lining the heated end of the silica tube with thin molybdenum sheet. A double silica tube was required to eliminate loss of hydrogen by diffusion through silica at high temperatures and high hydrogen pressures, the space between the tubes being maintained at a hydrogen pressure equal to that above the specimen. Hydrogen was purified by diffusion through a Ag-Pd tube.= Hydrogen pressures were measured with a mercury McLeod gage in the range 0.001 to 4 Torr

Jan 1, 1968

By A. A. Venghiattis

This paper is discussed not because of its intrinsic value but because it has been related by its authors to the oilwell gun perforators. It is well known that conditions almost ever present in oilwell perforations are the overburden and the presence of the casing. Because of the lack of information in the paper on the dimensions or confinement of the target rocks, one is led to guess that they were not confined at all and, particularly, that no steel front plates were used on the impact face of the rocks to materialize the presence of the cemented casing. This situation, plus the fact that small steel balls have been used as projectiles instead of actual bullets, makes the whole thing unapplicable to oilwell perforation. When shooting is performed against target rocks confined (as shown on Fig. 1) in such a way as to give a fair image of the overburden applied to the formation to be perforated, as well as of the cemented casing, the following are found. 1. There is no cratering worthy of mention, even with bullets having 10 times higher impact energy per unit projected area than the steel balls mentioned in the article. This has been confirmed with sandstone as well as with other rocks (granite, limestone and chalk). See Figs. 2 and 3. 2. Penetrations vary closely as the logarithm of the impact velocity. On this matter I have established the relation

By C. L. Sollenberger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature's to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent.

Jan 6, 1958

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By T. F. Witheree

The Fletcherville Furnace was built in 1864 and 1865, making its first blast from August until October of the latter year, when it was blown out to prevent its " bunging-up." Repairs were made in time to enable it to be blown in again December 12th, 1865, the blast ending October 7th, 1866. Total product 1921.15 tons iron, an average of 6.8.2.5 tons per day, from ores yielding 44.8 per cent. Consumption of charcoal 223.2 bushels per ton of iron. The furnace journal up to this time shows no record of furnace dimensions, or temperature of the blast, but as near as can be ascertained, they were as follows, viz.: Height of stack, 42 feet. Diameter of bosh, 11 feet. Angle of bosh, 71/2 inches to 12 inches rise, about 58°. Diameter of open tunnel head, 42 inches. Number of tuyeres 3 ; each 3 inches in diameter. Dam 15 inches high. Tuyeres 24 inches high. Tymp 224 inches high. Diameter of steam cylinder, 20) inches. } Diameter of blast cylinder, 64 inches. } Stroke 5 feet. The engine is direct-acting horizontal non-condensing. December 26th, 1866, the furnace was again put in blast, having been considerably altered in the crucible; the height of stack, bosh, and tunnel head remaining as before. Six tuyeres were put in, three in each of the side arches. The hearth or crucible was rectangular in form, 3 feet wide x 31/2 feet long x 64 feet high. Inclination of bosh 58°. Height of tuyeres 26 inches; nozzles 21/4 inches diameter. Temperature of blast estimated to be about 500°.

By A. E. Nash

This title is somewhat of a misnomer, because it does not accurately describe the phase of heat generation and application coming within the scope of this discussion. This paper is concerned primarily with that particular phase of radiant-heat transfer sometimes erroneously referred to as "shielded" radiant heat, to differentiate it from the open radiant heat of either flame or settings, in which the actual source of the radiant heat is a small incandescent furnace composed of a highly conductive superrefractory, within whose walls the combustion of the fuel is completed. This small furnace is usually located directly in the furnace proper, and although its refractory walls do shield the heat-absorbing surfaces from contact with the gases of combustion, there is no interference with the radiant heat given off by the furnace itself. We do not believe it either necessary or advisable to shield or screen radiant heat when properly controlled and applied. We do believe it essential to prevent the excessively hot gases of combustion from coming in contact with those parts of the heat-absorbing structure that are already receiving heat at high rates by radiation. In connection with any process for the refining of oil with which we are familiar, we are convinced that it is most advantageous to transfer the maximum of the heat generated in the form of radiant heat, applied directly to the heat-absorbing surfaces without the interposition of any form of shield or screen to prevent or reduce the radiant-heat transfer. While the term radiant heat is broadly used to cover all heat energy transferred from one body to another by radiation, in contradistinction to heat given up by gases in direct contact with the heat-absorbing structure (convection) or transmitted simply by conduction, in furnace work it is perhaps more often limited to the heat rays given off either by

Jan 1, 1928

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."' Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.&apos; More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By W. Edeburn, H. R. Fife

An extended study of dustproofing Freeport-seam coal has emphasized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption propcrties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measurements on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average tori of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by surface area. Wax extraction data on 1-in. to 0 slack from mine-run treated Freeport-searn coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness. The actual cost of the pretipple and supplemental treatments was very low per ton of coal treated, while the net or true cost was sufficiently

Jan 1, 1938

By Arthur F. Wendt

The earliest knowledge of copper-ores in the Southwest was derived from the Mexicans, who, in the latter part of the last century, discovered and worked the Santa Rita copper mines, now situated

Jan 1, 1887

By Claude P. Heiner, Carl S. Westerberg

OBSERVATION of the clinkering action of coal from the Castle Gate D seam in underfeed stokers over a period of years has given rise to the present investigation of the effect of bony coal on clinkering. Some very costly examples of slagging clinkers in particular cases have been of especial interest to the authors. In such cases coal analyses and ash-softening and fluid temperatures have been found of little value. In general, it was noted that slagging was accompanied by a somewhat higher ash content of the stoker slack, and the suspicion naturally arose that foreign matter was the troublemaker. One would naturally suspect bony coal and rock impurities because of their occurrence and prevalence within the seam and the relative absence of sulphur or other impurities in the coal mined. The test results given herein indicate that the concentration of the bony coal and rock impurities in the coal determines the clinkering tendencies of the ash during combustion. CASTLE GATE D SEAM Extending from the Utah-Colorado line near Grand Junction, Colo., westward to Greenriver, Utah and thence in semi-circular form north and westward to Castle Gate, and from there southward to Mt. Hilgard in central Utah, is a line of nearly perpendicular cliffs, composed of interbedded massive sandstone and shales, making up the coal-bearing horizon of the Mesaverde formation of Upper Cretaceous age. The cliffs face roughly concentrically toward the south and southeast and the strata, with conformably enclosed coal beds, gently dip away from the face of the cliffs and at right angles to their front line. Back of these cliffs the mountain masses rise to an altitude of from 8000 to 10,000 ft. above sea level. Stretching away from their foot is a great shale plain, on which the towns are situated and over which the railroad lines and highways run. The Castle Gate mines enter the coal beds at their outcrop; the workings extending within a particular coal bed away from the outcrop and under the mountain mass back from the cliff line (Fig. 1). Throughout the Mesaverde formation in the Castle Gate general area, there are from two to five workable coal beds. Usually not all of these are coincidentally of workable size and merchantable quality throughout any given large tract. In the Castle Gate mine area, the base of the Mesaverde horizon and coal measures is marked by a massive, cliffmaking, gray sandstone bed 6o to 8o ft. thick. Locally this is referred to as the "Castle Gate sandstone floor." Frank R. Clark, in U. S. Geol. Survey Bull. 793, designates it as the "Aberdeen sandstone." At Castle Gate the various coal beds are designated by the letters A, B, C, etc., commencing with the lowest bed. Fig. 2 is a graphic generalized vertical section, compiled from physical exposures

Jan 1, 1941

By P. W. Bakarian, C. H. Mathewson

THE greater part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation, in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)1 by geometrical analysis identified the {102} ? plane in magnesium as the twinning plane, Schiebold and Siebel (1931)2 confirmed this twinning plane, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also reported twin formation in a secondary role on the {101} plane. Schmid (1931)3 summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-i.e., the critical resolved shear stress-were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C., at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the original specimens of circular section had been

Jan 1, 1943

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By Theodore B. Comstock

Prior to 1885, the College of Engineering in the State University was under the care of such professors and instructors as were required for efficient work in the Schools of Mechanical Engineering, Civil Engineering and Architecture. The development of the coal and other important mineral resources of the commonwealth led gradually to a considerable demand for instruction in the branches more closely related to mining engineering, and a very creditable effort was made to meet this want by arranging special work in the field and in the laboratory for students of mining and metallurgy. This plan, while it gave much added labor to several already heavily taxed professors, caused such students to become something like undesirable excrescences upon the regular courses. But its partial success gave abundant proof of the real necessity for a complete course in Mining Engineering. The famous Braidwood disaster emphasized anew the importance of thorough training on the part of those to whom the responsible duties of mining must be confided. As is well known, a very excellent beginning was made some years ago by the Legislature in the matters of inspection and regulation by the enactment of a reasonably effective law, which was afterward much improved.* About the date of the last Acts, it was deemed wise to enlarge the facilities at the University arid to furnish adequate training for the increasing number of applicants. Accordingly, in August, 1885, the writer was requested to assume the duties of the professorship, it being the expressed desire of the Board of Trustees and the Regent of the University that a School of Mining Engineering should be founded which might eventually come to rank with the other engineering schools already flourishing here. It is the main object of this paper to state plainly the steps thus

Jan 1, 1887

By C. E. Wood

THIS paper is a brief report of experimental work undertaken to determine whether barium oxide in any quantity increases the desulfurizing action of blast-furnace slags. Industrial furnace operation with slag containing small quantities of barium oxide, referred to later, interested S. A. Sanford of the Commercial Chemical Co., Youngstown, Ohio, to conduct experiments to furnish comparative results on desulfurization with normal slag and slag containing small quantities of barium oxide. The U. S. Bureau of Mines agreed to assist on the problem because of the possible saving in fuel if the desulfurizing action of blast-furnace slag can be substantially increased, also because the experiments would yield new information on sulfur elimination in general, a matter of economic importance in furnace practice. A more complete and fundamental study of desulfurization of iron by slag is in progress.

Jan 1, 1929

Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Board of Directors of the A. I. M. E., through their monthly meetings, a report of the year&apos;s progress is almost superfluous. To the members who read the monthly reports of. the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed, or were working in other industries. Toward the end of the year, higher metal, prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 3, 1925