Search Documents

By W. M. Hirthe, E. H. Greener, D. R. McCann

It has been proposed1'2 that, at low temperatures, point defects are a strengthening factor in inter-metallic compounds whereas, at high temperatures, the deformation is diffusion-controlled and, therefore, an increase in the concentration of point defects tends to soften or increase the plasticity of a compound. More recent investigations, including those of Bloem and Kroger' on PbS, Kramers and smith4 on TiO, and Nadeau5 on LiF, have extended this concept to ionic crystals. Rutile (TiO2) is a tetragonal transition metal oxide which has a defect structure over at least the compositional range. The defect in near-stoichiometric rutile is either an oxygen ion vacancys or a titanium ion interstitial.' This investigation does not contribute to resolving the defect question but either defect would satisfy the results obtained. Six specimens having the same orientation, see Fig., 1, utilized in an independent investigation1' were cut with a diamond saw from a single-crystal boule purchased from the Linde Co. Three specimens were annealed in air at 1200°C for 4 hr and slowly cooled to room temperature in a period of 12 hr. The remaining specimens were reduced in a vacuum of l0 mm Hg at 1200°C for 4 hr and cooled at the same rate in vacuum. The reduced specimens were weighed before and after reduction and, assuming the weight loss to be oxygen, the corresponding oxygen-to-metal ratio is 1.998. All specimens were chemically polished and etched utilizing the techniques described by Hirthe, Adsit, and Brittain." The specimens were embedded in acrylic resin and mounted on a leveling vise in a Kentron micro-hardness tester. A 200-g load was applied to a Knoop indenter with a descent time of 18 sec and a dwell time of 20 sec. Eight indentations were made on a near (171) surface, approximately 3 deg from the (lii) plane, for each orientation of the major axis of the indenter relative to the crystal structure. The dependence of microhardness on orienta-

Jan 1, 1963

By J. M. Smith, D. Kunii, P. Adivarahan

Effective thermal conductivities were measured for seven samples of porous rocks through which gases or aqueous salt solution were flowing, parallel and countercurrent to the flow of heat. The results are analyzed in terms of the contributions of the solid and fluid phases to the total energy transfer. The solid contribution for the sandstone samples studied was found to be a Junction of the porosity and an effective thermal conductivity for the solid phase. The fluid contribution was a function of the Peclet number. Based upon the equations presented, the effective conductivity of the system can be estimated from the properties of the fluid, the flow conditions, and the porosity and pore-size distribution of the rock. INTRODUCTION Heat-transfer characteristics of porous media containing fluids are needed for the design and evaluation of thermal methods of petroleum production. The study reported here considers the problem of countercurrent flow of fluid and heat in sandstone rocks, and is a continuation of previous studies concerned with parallel and radial flow of energy and fluid in both rocks517 and beds of fine particles.6,10 In addition to these earlier works, Asaad,1 Kimura,4 Preston,8 Zierfuss and vlietll and waddams9 have reported effective conductivities for systems filled with stagnant fluids. There appears to be no published data on rocks through which fluids are flowing. The purpose of this study was to present such information and, particularly, to investigate the effects of properties of the rock and the flow rate on the results. The rock samples were naturally occurring sandstones from different locations and were similar to petroleum-bearing formations. The properties of the seven samples showing the range in porosities and permeabilities are given in Table 1. The mean pore sizes were calculated from mercury penetration data by averaging the radius with respect to pore volume. The details of this method and comparison with other procedures for estimating 7 are given elsewhere. Four fluids, nitrogen, carbon dioxide, helium and 10 weight per cent sodium-chloride solution were used with each sample. For Bartlesville sandstone, BA-5, runs were made at mean pressures from 15 to 250 psig using nitrogen. The other measurements were carried out at a mean pressure of 100 psig. The maximum temperature range eacountered was 70° to 300°F. The flow rate of fluid ranged from about 1.0 to 130 Ib/(hr)(sq ft), and this corresponded to a modified Reynolds-number range of 5 x 10-4 to 1.0. The variation in Prandtl number was 0.70 to 4.1. EXPERIMENTAL WORK The equipment consisted of apparatus to supply a constant flow of gas, or salt solution, at constant pressure to the bottom of a vertical test section, and metering and flow-regulation apparatus after the test section. The flow of salt solution was

By William R. Webster

At the Florida meeting of the Institute, in March, 1895, I presented a Note on a Proposed Scheme for the Study of the Physics of Cast-Iron,1 giving an outline which, for convenience of reference, I here repeat. Suggested Lines for DiScuSsion and IvestiGation. I.—Correspondence between chemical composition and melting-point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: 1. Cupola-mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting-temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6 Kind of mold, green sand (under dif- on E. Chill. ferent conditions of ramming, amount F. Residual strew of moisture, and skin-dried), dry sand, G. Condition and quan- loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum, III. —-Segregation as affected by : 1. Composition ; 2. Casting-temperature; 3. Rate of cooling ; 4. Size and shape of casting. IV. —Blow-holes, their volume and position as affected by: 1. Composition; 2. Casting-temperature; 3. Casting-pressure ; 4. Rate of cooling; 5. Size and ehape of casting ; 6. Special additions. It was hoped that a discussion might thus be elicited, similar in interest and value to the discussion of the physics of steel, which had been so widely and gratefully welcomed by students and practitioners in that department. That this hope was not

Jan 1, 1905

By C. Coles, J. A. I. Young, W. A. Wyeth, D. A. Fenton, G. W. Herzog

The reliability of large diameter, high horsepower ball mills is paramount when large production and minimum downtime is required. The 518 x 1706 mm (17 x 56 ft) double compartment ball mill at St. Lawrence Cement Co. has the fist gearless drive built in North America and has the world's largest hydrodynamic bearings currently built and running. The machine has seen three years operation and has met its specifications. The mill wm designed by Aerofall Mills Ltd. and the gearless drive built and designed by the Canadian General Electric Co. The paper discusses the operation of the machine from the mechanical, electrical and process aspects.

Jan 1, 1980

By Nick A. Hasenack, Heinz Kister, Rolf B. Vogel, Kees H. van Toor

A full survey of the laboratory and blast furnace tests carried out on two types of acid pellets is given. From the lab tests it appears that type B has a better low temperature disintegration index and a lower reducibility index than type A. The chemical composition and swelling indexes do not differ for both types. From the blast furnace test periods, carried out with a charge of 45% of pellets and 45% of sinter, it follows that both types of pellets lead to the same pig-iron production, blast furnace permeability, and blast furnace dust production. It also can be concluded that type B pellets cause a significantly higher coke consumption.

Jan 1, 1977

By D. W. Smith

The beta solid solution phases of the systems copper-zinc, copper-aluminum, copper-tin and silver-zinc are structurally analogous.' R. F. Mehl and 0. T. Marzke2 have shown that the a phase upon segregating from the 6 phase in the system copper-zinc takes the form of needles lying parallel to a [Ill] direction or some similar direction, such as [556], of the parent solid solution, and that the a phase upon segregating from the ß phase in the system copper-aluminum also takes the form of needles. By analogy they assume that in this case also the segregate needles lie parallel to the [ill] or [556] direction in the ß lattice. The purpose of this investigation is to determine whether the structures resulting from segregation of the a phases from the respective ß phases of the systems copper-tin and silver-zinc are analogous to those obtained by Mehl and Marzke in the systems copper-zinc and copper-aluminum. Segregation of the a Phase from the ß Phase in the Copper-tin System Preparation of the Alloy.—An alloy containing 74.92 per cent (by weight) of copper and the balance tin was chosen for this investigation. This alloy, as can be seen from a portion of the constitutional diagram, Fig. 1, of the system copper-tin by Hamasumi and Nishigori,3 with the proper heat treatment should segregate the « phase out of the a parent, solid solution phase. The alloy was prepared from high purity cathode copper (analyzing 99.98 per cent Cu) and Straits tin (analyzing 99.94

Jan 1, 1933

By E. J. Roberts

F. C. Bond (Allis-Chalmers Mfg. Corp., Milwaukee) —This paper considers comminution as a first order process, with the reduction rate depending directly upon the amount of oversize material present. The data show that other factors should be taken into account, and it is possible that in time these may be evaluated as simultaneous or consecutive reactions: Development of the theory of comminution has been retarded for many years by the assumption that surface area measurements constitute the sine qua non of the work done in crushing and grinding, and it is encouraging to note the belated growth of other ideas. In the Abstract the term "net power" should be changed to "net energy." Throughout the paper the term "hp per ton" should be changed to "hp hrs per ton", or "hp hr t." The term "Probability Theory" in the title does not seem appropriate, since it is not clear how the probability theory is used in developing the ideas in the paper. There seems to be a contradiction between the large calculated advantages of closed circuit operation and the statement following that the closed circuit test results showed no significant change in grinding behavior, when compared with the batch grind curves. Tables I and II show that between 75 pct and 50 pct solids the energy input required decreases with increasing moisture content and may indicate the advisability of grinding at higher dilutions in certain cases. The calculation of the hp-hr per ton factor indicates an input in the laboratory mill of only 7.32 gross hp per ton of balls; this casts some doubt upon the accuracy of the factor used, since the power input in commercial mills at 80 pct critical speed is customarily much higher. The tests show that within fairly wide limits the amount of ore in the laboratory mill may be varied and a product of constant fineness obtained, provided that the grinding time is varied in the same proportion. This has often been assumed, and confirmation by actual testing is of value. The Cavg corrections for differences between the plant and laboratory size distributions do not seem very satisfactory, since in many cases the plant/laboratory ratio is farther from unity after correction than before. The following equation has been derived from the data in Table VI: Relative Energy (log new ball diam in in. + 0.410) Input = --------------—--------------- from which the relative energy inputs for balls of different sizes can be calculated and compared. The relative energy input is unity for balls of 2.715 in. diam. The equation indicates that the work accomplished by a ton of grinding balls per unit of energy input is roughly proportional to the square root of the total ball surface area; provided, of course, that the balls are sufficiently large to break the material. The data in support of this statement are admittedly meager, but are fairly consistent when plotted. The relative grindability values listed in Table VI for 200 mesh multiplied by 4/5 apparently correspond approximately to the A-C grindability at 200 mesh.' It would seem that for open circuit tests comparable accuracy could be obtained much more simply by the old method' of plotting the test grind, extending the mesh grinds to the left of zero time if necessary, and determining from the plot the equivalent time required to grind from the plant feed size to the plant product size, using the average of several mesh sizes. The en- ergy input value of one time interval could be determined by tests on materials of known grinding resistance, and this multiplied by the interval required should give the desired energy input value. The relative grindabilities would be the relative time intervals required for a specified feed and product size. When the plotted mesh size lines of a homogeneous material are extended to the left beyond zero time they meet at one point at zero pct passing. The horizontal distance of this point from zero time indicates the equivalent energy input required to prepare the mill feed. The author's results show that the closed circuit grinding tests give about the same K values as open circuit tests, from which he concludes that open circuit tests are satisfactory in many cases. The value of the closed circuit test is its ability accurately to predict energy requirements in closed circuit grinding for both homogeneous and heterogeneous materials. If the material is homogeneous, the open circuit test gives satisfactory results; but if the material contains appreciable fractions of hard and soft grinding ore, the open circuit tests will not be accurate because of the accumulation of hard grinding material in the circulating load. Since in most cases it is not possible to determine a priori whether the material contains hard and soft fractions, the closed circuit tests are preferable and more reliable. B. S. Crocker (Lake Shore Mines, Ontario)—Dr. Roberts probability theory of grinding is very similar to our log pct reduced vs. log tonnage method of plotting and evaluating grinding tests at Lake Shore. However, although we both seem to start at the same point we finish with different end results. Shortly after publishing our grinding paper (referred to by Dr. Roberts) in 1939, we did pursue the subject of the "constant pct reduction in the pct +28 micron material for each constant interval of time. We ran innumerable tonnage tests on the plant ball mills, rod mills, tube mills with 11/4 and 3/4 balls, and lastly pebble mills, with tonnage variations from 180 tons per day to 950 tons per day. We found that when we plotted the log of the tonnage against the log of the pct reduced of any reliable mesh, we had a straight line up until 90 pct of the mesh is reduced. We have also tested this in our 12-in. laboratory mill with the same results. We have used this method of evaluating grinds for the past 8 years and developed the recent four stage pebble plant on this basis. By pct reduced we mean the percentage of any given mesh that is reduced in one pass through a mill at a given tonnage (or time). For example, if the feed to a rod mill is 90 pct +35 mesh and the discharge at 500 tons per day is 54 pct +35, the pct reduced is 90 — 54/90 = 40 pct. If the feed had been 80 pct +35 the discharge would have been 48 pct +35 or pct re- duced 80-48/80 = 40 pct as long as the tonnage re- mained constant at 500 tons per day. Thus we can easily correct for normal variation of mill feeds. This log — log relationship derived from the tonnage tests of all our operating mills has proved of tremendous help in checking laboratory work and in designing alternate layouts or new plants. The difference between the log — log and the semi-log plot is only shown up when the extremes in tonnages are plotted. When the relationship between the pct reduced and the tonnage was first investigated, we used semilog

Jan 1, 1952

By J.W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By J. W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By Gilbert Francklyn

The requirements of coals for the manufacture of coal gas, water gas and producer gas will be considered sparately and a short description of each gasmaking process will be given. In this report the term "gas coal" is confined to coals suitable for the manufacture of city gas in horizontal, inclined or vertical retorts. The report does not refer to coke-oven practice.' Briefly, the process of manufacture consists of distilling the coal at high temperature in an externally heated retort out of contact with the air. The products of distillation, consisting of gas, tar, ammonia, etc. are collected and purified. The residue consists of coke, which is removed from the retort at the end of the carbonizing period. To supply the heat required in the process, a portion of the coke produced is converted into producer gas, which is burned under the retort settings. Qualities of Gas Coals The chief qualities that coal must possess in order to be classified as a gas coal are as follows: 1. Gas Yield.—The coal must be capable of yielding gas in sufficient volume and of a satisfactory quality. The yield depends considerably upon the temperature of distillation; a higher temperature will give a larger yield of gas, but the qualit,y of gas (now measured by the British thermal units per cubic foot) will be lower, while a lower carbonizing temperature will give less gas of higher heating value. The true measure of the yield is the number of British thermal units produced in the gas from a given quantity of coal. This number is obtained by multiplying the cubic feet of gas from 1 lb. of coal by the British thermal units per cubic foot of gas; it is called B.t.u. feet per pound. It is found that the

Jan 1, 1930

By M. Bevis, E. O. Fearon, P. C. Rowlands

Fe-Ni and Fe-Ni-C martensite specimens have been deformed in compression at room temperature and the habit planes of operative deformation twins determined by two-surface optical trace analysis. The full orientations of the martensite crystals were determined from divergent X-ray beam diffraction patterns. The experimental results are in excelled agreement with predicted twinning modes. In particular, the habit planes of some deformation twins in bcc martensites are consistent with a "Type XI compound'' twinning mode with Kl, Kz, 71, 77~ elements given by {5, 8, 11) {ioi}, (33) (ill) Tetragonal derivatives of this mode are operative in bct martensites. UnUSUAL deformation twinning modes have been reported by Richman' to occur in Fe-Ni-C martensites with bcc and bct structures. The twin habit planes were determined by single-surface trace analysis (pole locus method) and the remaining twinning elements were determined from the geometry of twin-twin intersections. The indices assigned to the observed habit planes are (3 101, "(089)" and "{0, 1,13)" or "{1,2,7} ", and only in the first case do the twinning elements correspond to a predicted twinning mode. This is mode 1.4 in the paper by Bevis et al. The results presented in Ref. 2 indicate that previously unpublished bcc and bct modes should be operative in preference to the (130) mode and anomalous modes reported by Richman. In view of these results and the uncertainties involved in determining habit planes from single-surface trace analysis and twinning elements from twin-twin intersections5 a two-surface trace analysis of deformation twins in Fe-Ni and Fe-Ni-C martensites has been carried out. EXPERIMENTAL PROCEDURES Two alloys with compositions Fe-23 pct Ni-0.6 pct C and Fe-30.4 pct Ni were prepared from 4N pure materials by induction melting under a vacuum of 10"5 mm Hg. The alloys were homogenized at 1350'~ for 5 days. Both of these alloys are austenitic at room temperature with M, temperature - — 50"C. The aus-tenite grain size of the Fe-Ni-C alloy was approximately 300 to 400 p. The Fe-Ni alloy was remelted in a vertical tube furnace and the melt lowered slowly from the hot zone of the furnace to produce s ingle -crystal austenite specimens. Specimens approximately 10 by 5 by 5 mm were cut from the ingots and quenched to various temperatures below the Ms temperature. The specimens were elec-tropolished in a 10 pct perchloric acetic electrolyte before being deformed in compression at room temperature. Martensite plates which exhibited profuse deformation twinning were selected for analysis and the specimen polished on a second surface such that the two surfaces which contained the martensite plate enclosed an obtuse angle of approximately 145 deg. The specimens were then electropolished to reveal the traces of the deformation twins on both surfaces. The full orientations of the martensite crystals were determined using a divergent X-ray beam technique (Kossel line technique) employing an AEI SEM2 electron probe microanalyzer. Details of this technique which include a detailed description of the Kossel camera attachment to the microanalyzer used in the present experiments have been discussed elsewhere.3 Only additional details relevant to this investigation are discussed here. The specimens were mounted with one surface normal to the incident electron beam as illustrated schematically in Fig. 1. The martensite plates to be analyzed were located using the normal scanning equipment of the microanalyzer. The position of the electron beam and hence the position of the source of divergent X-rays generated within the crystal could be located to within 1 p. Exposure times of approximately 8 to 10 min were required for back-reflection Kossel patterns and it was found that useful diffraction patterns could be obtained consistently from heavily deformed martensite plates. A reference line (carbon contamination mark) produced on the two surfaces of the specimen by scanning the electron beam in a direction having a known relationship with the reference !ine in the X-ray camera enabled the full orientation of the crystals to be determined. Martensite plates with widths as small as 8 p could be oriented using this procedure. The Kossel line patterns were interpreted using the charts developed by Rowlands and ~evis~ as generally

Jan 1, 1969

By R. W. Heckel

The growth and shrinkage rates of second-phase particles of various size distributions are analyzed in terms of five mathematical models. These models apply to various forms of diffusion-controlled growth (one model) and interjace-controlled growth (four models). The expression for diffusion-controlled growth assumes local equilibrium at the interface between the second Phase and the matrix and through the choice of the proper flux area perrnits the definition of minimum diffusion-controlled growth kinetics. The interface-controlled kinetics models consider the situations where the rate-controlling step occurs at either the interlace undergoing solution or the interface undergoing deposition. In addition, each of these interface-controlled kinetics models is analyzed for interface reaction rates which are independent of the thermodynamic activity gradient across the interface or proportional to the gradient. THE variation of the size distribution of second-phase particles in a solute-saturated matrix has been a stimulating topic for many years. Research has been carried out in this area for situations where the matrix was either liquid or solid. It is well-understood that the over-all process results in an increase in the average particle size, a decrease in the total number of particles per unit volume, and a net decrease in surface area. Greenwood1 has presented a mathematical model based upon the mass balance existing between growing and shrinking particles. His analysis is stated in terms of Fick's First Law using concentration gradients set up between particles of different size as a result of the effect of surface curvature on solubility. Greenwood's analysis indicates that the mean particle size should increase approximately as the cube root of time. Asimow2 has shown that several of the simplifying assumptions employed by Greenwood may be eliminated from this diffusion-controlled model with little increase in complexity. Lifshits and Slyozov3-5 have also considered the growth-shrinkage problem involving diffusion-controlled kinetics. Their analysis was extended to include the effects of interacting particles ("kinetic approximation"), particle shape, and elastic strains. These authors also show that the mean particle size varies as the cube root of the reaction time. wagner6 has formulated expressions for both diffusion-controlled kinetics and interface-controlled kinetics in the growth-shrinkage problem. Wagner's diffusion-controlled kinetics is based upon the same form of mass balance using Fick's First Law as used by others and is shown to be applicable to situations where kr >> D (k is the interface reaction constant, r is the particle radius, and D is the diffusion coefficient). This analysis also yields a mean particle size which varies as the cube root of time, in agreement with other workers. Wagner also developed interface-controlled kinetics to handle kr « D. This model was based upon the fact that the interface reaction rate is proportional to the interface area. Wagner assumed that the rate was also proportional to the thermodynamic activity difference, ?a, existing across the interface. Thus, the specific reaction rate at the surface of radius r was defined as k • 4nr2 . ?a. It is the purpose of the present paper to reconsider the processes of diffusion-controlled growth and interface-controlled growth in the variation of particle-size distributions as a function of time at constant second-phase volume. The analyses are formulated in a manner which permits data obtained

Jan 1, 1965

By George Sachs, S. M. Clark, George Espey

he tendency of a commercially drawn cartridge case to crack in the mercury test and the relation of cracking tendency to residual stress retained after drawing were studied. The fourth drawpiece (next to the final) of caliber 0.30 cartridge cases produced by Frankford Arsenal were selected as test pieces. These exhibited an exceptionally high cracking tendency, making a detailed study possible. To obtain fast cracking in the mercury test, about 0.0015 to 0.003 in. must be removed from the wall thickness of the drawpiece by pickling, and it must be subjected to the mercury test immediately after washing. Removal of the adhering mercury by annealing and subsequent squeezing of the case in a vise was used to reveal definitely the presence or absence of cracks. Various lots of apparently identically fabricated cases were shown to possess a different cracking tendency. Machining off or boring a hole in the base gradually reduced and eventually eliminated the cracking tendency. On the contrary, shortening of the wall (body) reduced the cracking tendency only if the wall became so short that the cracking zone was directly affected. By boring out the base and pickling from the outside and then splitting the resulting rings, it was possible to determine the approximate stress distribution in the base and in the adjacent part of the wall. Small compression stresses were present in the core and the major part of the base, while the surface of the base and the adjacent wall contained high circumferential tensile stresses. On the contrary, the wall when parted from the base contained only insignificant residual stress. The conception is advanced, that the stress distribution in a drawn cartridge case corresponds fundamentally to that of a tube (wall) shrunk on a disk (base). Such a stress distribution results from the tendency of the base to recover elastically by an increase in diameter from the biaxial compression during drawing while the wall exhibits little tendency to change its diameter after progressing through the die. This is confirmed by measurements which show the base diameter to be slightly larger than the wall diameter.

Jan 1, 1945

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By W. E. Keck, Paul Jasberg

The flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.—For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.—The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into — 65 + 200 and — 200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The —200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1939

By W. E. Keck, Paul Jasberg

The flotative properties of the principal minerals in Michigan's potential iron ores have been investigated to develop methods of bene-ficiation for the ores. One of these minerals, magnetite, is of considerable importance as a source of iron. Study of its flotation was similar to that of hematite1, another iron mineral in these potential ores. The present research consisted essentially of: (1) a survey of the literature on magnetite flotation, (2) the preparation of pure magnetite, (3) the development of laboratory procedure and (4) flotation experimentation. Literature on Magnetite Flotation.—For the purpose of this discussion, the results of previous work on the flotation of magnetite can be summarized as follows. The mineral has been floated with pine oil2, and it has also been separated from synthetic mixtures with silicates by the use of the same reagent2. Magnetite and apatite in iron-ore slimes have been separated by flotation of apatite with sodium palmitate3. These data were utilized in the present investigation. Preparation of Magnetite.—The pure mineral was prepared from the magnetic-separator concentrate of an iron ore (obtained from the Wither-bee Sherman Corporation, Port Henry, N. Y.). This concentrate was slowly comminuted with laboratory rolls and pulverizer to pass 65-mesh and was then tabled several times. Tabling yielded a relatively coarse magnetite concentrate, tailing and slimes. The two latter materials were rejected insofar as the present work is concerned, and treatment of the magnetite (table concentrate) was continued by separating it into — 65 + 200 and — 200-mesh sizes. Separation of the sizes was made by first dry screening and then wet screening. The —200-mesh material was rejected to eliminate possible introduction of error into flotation

Jan 1, 1939

By M. E. Wadsworth, P. H. Yu, C. K. Hansen

A study of the rate of dissc5lution of chalcopyrite (CuFeS2) in acidic solutions under oxygen overpressures was carried out by measuring the rate of formation of cupric ions in solution. Effects of temperature, oxygen partial pressure, surface area, and concentration of sulfuric acid were evaluated. A sized batch of chalcopyrite was leached in the temperature range of 125° to 175°C and in the pressure range of 75 to 400 psi of oxygen. In 0.5 N H2SO4 all products of reaction went into solution except for trace amounts of elemental sulfur. The dissolution of chalcopyrite followed linear kinetics and was essentially independent of hydrogen ion concentration for H2S04 concentrations between 0.2 and 0.5 N. The oxygen dependence indicated adsorption approaching limiting values with increasing oxygen pressure. The linear mechanism was explained in terms of steady-state adsorption of oxygen at the chalcopyrite surface followed by a surface reaction. The enthalpy of activation for adsorption of oxygen was found to be approximately 33 kcal per mole. An activation enthalpy of approximately 9 kcal per mole was observed for the surface reaction. Charge transfer reactions are not rate controlling in the process.

Jan 1, 1973

By Richard B. Greenwalt, John M. Bertram, George E. Aiken

Agglomeration developments in the iron ore industry of North America over the past twenty years are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. As early as WW II the rich Mesabi hematites were depleted, ending a 50-year era of direct shipping ores that included reserves of an estimated three billion tons. Decreasing ore grades and rising costs began to force the closing of many underground iron mines and processes were being developed to use domestic low-grade iron deposits. This resulted in the rapid development of iron ore beneficiation processes and signaled the coming trend toward concentration, sintering and pelletizing. Yet even today when agglomeration facilities are treating 90 % of the Mesabi Range product much remains to be done in keeping world-wide competitive forces in check and in ensuring the long- term utilization of these expansive ore supplies in an up-until-now captive U.S. market.

Jan 10, 1973

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940

By Mark C. Malamphy

The occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltie petroleum first directed attention to the São Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a considerable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geophysical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area. General Geology The location and general geology of the São Pedro area are shown in the sketch map of Fig. 1, which is adapted from the geologic map of South Brazil compiled by Oppenheim1,†- who gives the geologic column of South Brazil (So Pedro and vicinity) as follows:

Jan 1, 1940