Search Documents

By Henry A. Stiff, J. P. Hammond, A. B. Westerman, H. C. 195-000-000-014 Cross, and Lawrence E. Davis

The phases in Cr-Fe-Mo alloys have been investigated with homo-genization, aging temperature, composition range, and alloy addition as variables. Metallography, three X-ray methods, and hardness were used as methods of study. The behavior of s, M23,C8, and Z phase are reported for cornpasition range 60 pct Cr-15 to 25 pct Fe-15 to 25 pct Mo-<0.005 to 0.36 pct C with aging at 1400º to 2000°F. With 2 pct Ti, Tic and TiC-TiC are formed; with nitrogen Cr2N. THE recently developed class of chromium-base heat-resistant alloys shows appreciably higher strength than commercially used high temperature alloys. However, further developmental work is required to impart needed shock resistance and some degree of room-temperature ductility to these alloys. Extensive exploratory work on chromium-base alloys was begun in a program initiated by the War Metallurgy Committee of the National Defense Research Council at the Climax Molybdenum Co. in the early part of 1942.&apos; Alloys were sought for gas-turbine blades for use at 1600°F. A minimum of 5 pct elongation in the stress-rupture test was a requirement. From the Climax work, ternary alloys of chromium, iron, and molybdenum appeared to show the greatest promise as materials for gas-turbine blades. The composition line in the ternary diagram joining the 60 pct Cr-15 pct Fe-25 pct Mo and 60 pct Cr-25 pct Fe-15 pct Mo alloys was indicated as representing the most useful combination of strength and ductility.&apos; Strength increased while ductility decreased as molybdenum was raised in this composition range.&apos; The 60 pct Cr-15 pct Fe-25 pct Mo type alloy was thought to have the most suitable properties for gas-turbine blades.&apos; Concurrent with the study reported here, other investigations were being made on Cr-Fe-Mo alloys. The liquidus temperatures on a series of low carbon, ternary alloys were being determined, and isothermal sections drawn at 2370°, 2010°, and 1650°F (1300°, 1100°, and 900°C).2 Also, various methods of preparation and some mechanical and physical properties of chromium-base alloys, particularly the 60 pct Cr-15 pct Fe-25 pct Mo type, were being investigated., At the inception of the present program, only a limited study had been made of etchants for developing the microstructures of chromium-base alloys; X-ray analysis of the microconstituents had not been made. A review of the literature revealed that no phase-diagram work had been reported on the Cr-Fe-Mo system. Scope of Work The work on chromium-base alloys includes the following: 1—The development of etching methods for differentiating between the microconstituents; 2—The identification of microconstituents by X-ray diffraction methods; and 3—A comprehensive metallographic and hardness study after various heat treatments. The phases were studied by three standard X-ray techniques: 1—The block-sample focusing-camera method; 2—The powder-diffraction method on elec-trolytically separated residues; and 3—The powder-diffraction method on cold-worked aggregate samples. The results by the first two methods were correlated with the metallographic data. The third method was used largely to study conditions approaching equilibrium, since cold working prior to heat treating accelerated precipitation. Seven types of alloys were investigated: 50 pct Cr-50 pct Fe, 40 pct Cr-40 pct Fe-20 pct Mo, 55 pct

Jan 1, 1953

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,&apos; and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3&apos;4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By C. S. Barrett, P. Coheur

AXnealing twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the re-crystallization texture,&apos; and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (III), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3&apos;4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture— this is true, for example, with the (113) [ZII] texture so commonly reported for brass—hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism. Materials and Methods The samples investigated were of secondary copper (melted in belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice have not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip I. cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a camera2 that traversed

Jan 1, 1947

By S. E. Bretherton

THIS title introduces the subject I wish to describe to my fellow members, very few of whom, I hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, its circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the interests with which I was connected for smelting in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast. furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Cal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last. 18,951 tons smelted averaged 15 3/10, per cent. zinc) which we not only lost, but which it cost us money to lose.

Jan 8, 1913

By G. M. Schwartz, J. N. Gundersen

John W. Gruner (Professor Emeritus, College of Science, Literature, and the Arts, Dept. of Geology, University of Minnesota, Minneapolis) — It is surprising that two men as well acquainted with the taconite rocks of the Mesabi District as Drs. J. N. Gundersen and G. M. Schwartz should have concluded that the taconite of the Eastern Mesabi before the intrusion of the Duluth gabbro consisted largely of quartz and magnetite. These minerals were "locally reconstituted" into "a wide variety of silicate mineral assemblages" by the gabbro. It is well known, of course, that the silicate mineralogy of the Eastern Mesabi (&apos;about 14 miles in length) is quite different from that of the Main Mesabi which is over 60 miles long. The change from one to the other is abrupt and cannot be attributed to any other cause than the thermal effects of the gabbro. Are we to assume or believe that the taconite of the Eastern Mesabi was radically different from that of the Main range before the gabbro metamorphosed it?

Jan 1, 1962

The 118th meeting of the Institute was under the auspices of the Institute of Metals Division and the Iron and Steel Section, and was held at Milwaukee, Wis. The opening session was a joint meeting with the American Foundrymen&apos;s Association and the American Malleable Castings Association, and was presided over by Benjamin D. Fuller, President of the American Foundrymen&apos;s Association. At this time Hon. Emanuel

Jan 12, 1918

By Frank L. Nason

During the months of June and July of the present year, the writer made a special geological survey of the mining property of Messrs. Cooper and Hewitt, at Ringwood, New Jersey. Some of the results of this survey are presented to the society through the courtesy of Hon. Abram 8. Hewitt.

Jan 1, 1895

By J. Amanat, H. J. Siriwardane

A numerical procedure based on nonlinear finite element analysis has been developed for predicting subsidence profile over longwall mine panels. The developed procedure has been verified by comparing predictions with published field observations at several mine panels. This paper presents certain aspects of predicting subsidence profile over mine panels located in hilly terrain. Analysis of four such cases are presented herein.

Jan 1, 1984

By W. E. Curran

For years the geographical isolation of the Southern iron-ore district from the great producing centers in the North and East enabled it to meet its conditions and solve its own problems without regard to the practices and policies of other districts, but during the past few years distances have been shortened, practices and wages are being standardized, .and these changing conditions have brought new problems to the South.

Jan 1, 1937

By F. Z. Schellenberg

A recent visit with the engineering students of the Western University of Pennsylvania to the Keeling coal-mine on the south side of Pittsburgh furnished interesting matter to communicate, as may be the case, however, with regard to the striking features of any of our well-arranged larger collieries; for every mine surely appears unique as a whole, though description fails to give that impression, except in particulars.

Jan 1, 1900

By Otto H. Henry

The purpose of this investigation was to determine the equilibrium diagram of the lithium-magnesium pair as a first step in studying the possible usefulness of these alloys as ultra-light structural materials. Review of the Literature The behavior of lithium towards magnesium was first investigated by Masing and Tammann.(1)† In order to prevent oxidation the alloys were made in iron tubes under an atmosphere of hydrogen; temperatures were measured with a glass-protected thermocouple. These investigators found that lithium and magnesium form two series of solid solutions separated by a miscibility gap between 85 and 95 per cent magnesium; that the alloys with 81 and 95 per cent magnesium showed a homogeneous structure under microscopic examination, while the alloy with 89 per cent magnesium contained two distinguishable crystallites; that the curve indicating the beginning of crystallization rises from the melting point of lithium to that of magnesium; and that no compounds of lithium and magnesium are formed. The equilibrium diagram was not plotted because no definite data were obtained for determining the solidus and the position of the miscibility gap in the solid state. The difficulties encountered in this investigation were: (1) that it was necessary to heat them as high as the melting point of magnesium in order to obtain homogeneous melts; at such temperatures the alloys attacked the glass protecting the thermocouple; and (2) that at temperatures above 400" C. the lithium united with the hydrogen to form lithium hydride, thus contaminating the alloys. By applying the same methods as those used in the lithium-magnesium system, Masing and Tammann determined the equilibrium diagram of the

Jan 1, 1934

Jan 1, 1917

Feb. 18 to. 21, 1918 Committee on Arrangements J. E. JOHNSON, JR., Chairman BRADLEY STOUGHTON, Vice-Chairman A. R. LEDOUX RALPH W. DEACON F. T. RUBIDGE L. W. FRANCIS E. M. SHIPP MRS. S J. JENNINGS J. V. N. DORR A. L. WALKER G. D. VAN ARSDALE R. M. RAYMOND Finance Committee ALBERT R. LEDOUX, Chairman WALTER H. ALDRIDGE J. H. JANEWAY GEORGE D. BARRON CHARLES F. RAND WALTER DOUGLAS BENJAMIN B. THAYER

Jan 4, 1918

By R. N. Stevens

Any consideration of the errors involved in determination of ?gb by previous workers should discuss their experimental methods in terms of the appropriate theoretical equation; this the authors have not done in a number of cases. To facilitate the present

Jan 1, 1969

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall&apos;s statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall&apos;s statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By John Primrose

Tube stills having demonstrated their usefulness for refining operations, the later developments in their design have been in the direction of improved thermal efficiency. The earlier designs operated with low furnace temperatures and large volumes of furnace gas because the fuel was burned with much excess air. It was quite possible to provide sufficient heating surface to lower the temperature of the flue gas to within 150" of the temperature of the inlet oil, or when inlet-oil tempera-tures were high to have the flue gas escape at 300" or 350" F. by using the heat remaining in the flue gas from the still to preheat the air supplied for combustion. But even so, the thermal efficiency was low because of the large quantity of air used for combustion. The large quantity of excess air was required to burn the fuel in the furnace at a temperature low enough to prevent overheating the furnace walls and overheating of the oil. Supplying heat to the tubes of the heating surface at a rate beyond the capabilities of the oil to absorb, except with a considerable difference between the temperature of the inside of the tube and oil passing through, would result in overheating the tubes and the oil in contact with them. For these reasons it was very necessary in the older types of tube stills to burn the fuel with large quantities of excess air, resulting in low thermal efficiency despite the low flue-gas temperature. Neglecting loss by radiation, the thermal efficiency could be improved only by burning the fuel with less excess air, but it was necessary to accomplish this without upsetting the furnace temperature conditions existing when large quantities of excess air were used. There are several methods of bringing this about, such as controlling the furnace temperature by returning a proportion of the flue gas to the furnace, or by exposing direct to the fire a heat-absorbing surface so located and proportioned that sufficient heat will be absorbed by radiation to prevent excessive furnace temperatures.

Jan 1, 1928

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

By James B. Vance, Parviz Mottahed

An extensive research program has been carried out at PCS Mining for some time into the use of high frequency microseismic emissions in the range of 30-200 kHz for roof fall warning in the mines. A laboratory investigation on loaded samples of potash has established a close correlation between acoustic emissions and the applied load. The tests also indicated the occurrence of the Kaiser effect. The positive and encouraging response from underground testing and controlled laboratory testing has lead to the extension of the investigation into correlation of the high frequency microseismic emissions and the change in stress distribution due to mining. Hydraulic borehole pressure cells were installed at different depths ahead of the advancing boring machine. The output due to the stress change and the microseismic event count was monitored by a continuous chart recorder. This paper discusses the results of this instrumentation. The results confirm the strong correlation between the two measured parameters and outlines future areas of research for the use of the high frequency microseismic emission techniques in quantifying the changes in stress distribution.

Jan 1, 1984

By Olin G. Bell

At the beginning of the year 1935 the older fields in Southwest Texas, and particularly those discovered during 1934, had been practically delimited and only normal development continued. As a result, operations in this area were somewhat slowed down. Shortly after the first of the year, however, activity in the area was greatly accelerated, due largely to the fact that the Loma Novio field, discovered during the last few days of 1934, indicated the presence of a new productive trend east of and parallel to the Government Wells field and also indicated the presence of a new productive horizon, the Loma Novio sand, approximately 100 ft. lower than the Government Wells sand zone. Other discoveries during the year greatly augmented the activity in the district. During the year there were 651 oil wells, 53 gas wells and 275 dry holes drilled in this area during the year. Most of the operations were in the Government Wells, Cole, Loma Novio, Seven Sisters and Lopez fields. New Fields Four new fields were discovered during 1935 as follows: Seven Sisters and Piedra de Lumbre in Duval County; Loma Alto in McMullen County; and Lopez in Webb County. Seven Sisters Field.—The Seven Sisters field, opened in May, was the direct result of a systematic search for new productive areas northeast of the Loma Novio field. The first producer, Harvey & Henderson NO. 1 Chernosky, survey 226, was completed in the Labbe (Chernosky) sand at 2220 ft. However, the second producer, Santa Clara Oil Co. No. 1 Welder in survey 385, drilled about one mile south of the discovery well, failed to find production in the Labbé sand and was carried on down and completed in the Government Wells sand at 2473 ft. with an initial production of 20 bbl. of oil per hour. These two discoveries, in the Labbé and Government Wells sand, started an active leasing and drilling campaign in this part of Duval County and drilling operations continued especially active throughout the remainder of the year.

Jan 1, 1936