Search Documents

By Horace Pops

THE martensitic transformation occurring at cryogenic temperatures in the bcc ß-phase Cu-Zn binary alloys has been discussed in a number of publication~.1-3 Addition of a second solute element to the binary Cu-Zn alloys enables the ternary martensitic phase to be stable at temperatures above room temperature, and the variation of the MS temperature with third element content has been determined recently4 for a series of Cu-Zn based alloys in which either the zinc content or the electron concentration was maintained at a constant value. The present paper describes some characteristic growth features of martensite observed in ternary alloys. Alloys were prepared by adding small amounts of Ni, Ag, Au, Cd, Ga, In, Si, Ge, Sn, or Sb to a a -brass Cu-Zn master alloy. Details of the melting and casting technique, homogenization, examination by cold-stage microscopy, and the determination of the

Jan 1, 1968

By J. Chupak, D. J. Salley, G. L. Simard

Radiotracers were demonstrated to be of considerable value in a study of the interaction of dithiophosphate with galena. The interaction had characteristics of both chemisorption and chemical reaction, being complex because of the nature of the galena surface. Sorption was rapid and markedly reversible, and flotation occurred at relatively small amounts of dithiophosphate sorbed.

Jan 3, 1950

By V. K. Grotzky, F. J. Fraikor

A number of investigators have noted the importance of various precipitation reactions on the properties of commercial-purity beryllium.1-5 Carrabine, for example, has demonstrated the interaction of iron and aluminum on the mechanical properties of hot-pressed polycrystalline beryllium.6 He considered the determining factor on elevated-temperature properties to be a reversible AlFeBe, precipitation reaction which could be directly related to the Fe/Al impurity ratio of the beryllium. Any aluminum in excess of the stoichio-metric amount required to form A1FeBe4 was presumed to remain primarily in the grain boundaries. We have observed, by transmission electron microscopy, such a grain boundary effect after various heat treatments of beryllium sheet. The starting material in this investigation was bare-rolled beryllium ingot sheet (0.001 to 0.005 in. thick), in contrast to the hot-pressed powder utilized by Carra-bine. It should be noted from the ingot sheet analysis shown in Table I that the Fe/Al weight ratio was near unity which would provide some free aluminum although the total aluminum and iron content was still small. Fig. l(a) shows some aluminum or aluminum-rich precipitates in the grain boundaries of a beryllium foil which had been quenched from 1200°C into brine at -TPC. Similar grain boundary precipitates were found, particularly at grain boundary intersections, in other samples quenched from 1100° and 1000°C. The length of annealing time at these elevated temperatures did not appear to substantially alter the amount of grain boundary precipitates, thus attesting to their relative insolubility. No matrix precipitates were observed other than the normal BeO and Be2C inclusions. A microprobe analysis of the larger precipitates at

Jan 1, 1968

By G. L. Kulcinski, R. D. Leggett

Irradiated uranium containing 635 ppm of carbon, mostly in the form of UC precipitates, was annealed at temperatures from 650" to 900°C under hydrostatic pressures of 0 to 1000 bars. Postirradiation examination revealed that the carbide particles are not stable in the r phase of irradiated material but are stable in unirradiated material annealed under identical conditions. The degree of carbide dissolution appears to be connected with the fission product concentration and independent of annealing pressure. THIS paper describes the change in appearance of carbide particles in irradiated uranium after the uranium has been postirradiation-annealed. It has been proposed by several investigators&apos;-5 that fission gas-induced swelling in irradiated uranium may be reduced by incorporating a fine dispersion of second-phase particles into the metal. Because of the low solubility of carbon in uranium6 and the apparent stability of UC precipitates at high temperatures,6-8 this system has received some attention. The stability of UC particles to low-temperature irradiation has been demonstrated many times, as well as their stability during postirradiation anneals in the high a or B phases.9 Unirradiated uranium containing UC particles has been annealed high in the r phase, and the solubility of carbon was found to be only -115 ppm at 1050ºC.6 Vacuum annealing of irradiated uranium to the same temperature produces a spongelike sample, due to the formation and growth of fission gas bubbles."14 This highly disrupted lattice has made any determination of the stability of UC at these temperatures impossible. Nevertheless, it has always been tacitly assumed that the UC particles were still present. Recently, postirradiation, high pressure-high temperature tests have been performed on irradiated uranium containing a secondary phase of UC. 14 Examination of these samples after 100-hr, 900°C tests revealed that the carbides are not stable, and the results of these tests are presented here. 1) EXPERIMENTAL PROCEDURE The samples, high-pressure equipment, and subsequent analytical techniques are the same as those described elsewhere.14,15 Briefly, cylindrical samples of commercial-purity uranium that had been irradiated at <350°C to 0.37 at. pct B.U. were subjected to 90O°C, 100-hr anneals in NaK at pressures ranging

Jan 1, 1970

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,&apos;&apos; for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Jr. E. H. Dix.

In selecting the subject, "Acceleration of the Rate of Corrosion by High Constant Stresses,&apos;&apos; for the 1940 Institute of Metals Division Lecture, I have been influenced by its highly theoretical and speculative nature as well as by the great practical importance of the correct interpretation and appraisal of the engineering significance of the phenomenon. I lay no claim to originality in talking on this topic, since it has been the subject of discussion for over a quarter of a century. However, as our technical thinking advances, old phenomena take on new and more significant aspects. In our studies at the Aluminum Research Laboratories, we have encountered many perplexing and seemingly contradictory results and have been fascinated by the problem of dovetailing all of the many pieces of information to make a complete picture. I hope that in the brief period of this lecture I may share with you some of the enjoyment we have had in attempting to meet this challenge to metallurgical science. The emphasis generally has been placed on the spontaneous failure by cracking of a metal under the combined action of high stress and corrosion, hence the present-day use of the terms "stress corrosion" or "stress corrosion cracking." The older term "season cracking," applied more specifically to copper-base alloys, includes, by inference, the element of time. For the purpose of the discussion today I will use "stress corrosion" to cover broadly the effect of stress in accelerating the rate of corrosion of metals. To stay within the limits of allotted time the disrussiorl will cover the effect of high static stresses rather than repeated or dynamic stresses, which would take us into the related field of corrosion-fatigue. The subject is particularly appropriate for an Institute of Metals Division Lecture because much the same phenomenon has been observed in almost all metal systems. Thus, in addition to the season cracking of brass may also be mentioned the "caustic embrittlement" of steel boiler

Jan 1, 1940

By Carl H. Samans

In their recent complete review of the subject of age-hardening,&apos; R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers (&apos;discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By Carl H. Samans

In their recent complete review of the subject of age-hardening,&apos; R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plastically deformed has definitely been established.2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advancing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipitation will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers (&apos;discontinuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation. Crystallography of the Precipitation Process Through the extensive investigation by R. F. Mehl, C. S. Barrett and F. N. Rhines3 on the Widmanstätten structure in aluminum-rich copper

Jan 1, 1940

By J. B. Goddard

The discovery of rhenium on the ion exchange resin used at the uraniun in-situ leach operations at Palangana, TX, led to a laborabory study of possible recovery methods. Rhenium was present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, ReO4-. It concentrated on the anion exchange resin, which was a factor of 10 more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the per-chlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3N or stronger concentration of nitrate containing up to 0. 5N H + was found to be the system of choice. A rhenium sulfide concentrate containing up to 14010 Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4ReO4 followed by hydrogen reduction at elevated temperature.

Jan 1, 1984

By Henry M. Howe

SECTIONS 1. INTRODUCTION.—In this investigation the meltingpoint and the specific heat of certain artificial silicates were determined by the method of mixtures, using a large platinum-ball pyrometer. The silicates were placed in platinum crucibles on the hearth of a small regenerative gas-furnace (Figs. 1 and 2), and the platinum ball was placed between them. The temperature of the furnace was usually raised very slowly, the behavior of the silicates being observed as they gradually grew hotter; and their temperature was ascertained indirectly from time to time by determining that of the platinum ball, which to that end was temporarily withdrawn from the furnace and immersed in a known weight of water in a calorimeter. The weight and specific heat of water and of platinum ball being known (the specific heat of the latter approximately), it mas possible to calculate the temperature of the platinum ball, which was assumed to have been substantially that of the silicates which surrounded it in the furnace. The specific heat of the silicates also was determined by the method of mixtures. Their temperature having been determined as just described, one of them was dropped into a known weight of water in a calorimeter, whose rise of temperature was then noted. Knowing the weight and initial temperature of the silicate, its specific heat was wily calculated. The reults obtained, especially as regards the melting-point, must be regarded as first approximations. The technical difficulties encountered were so serious as to raise doubts, now from one cause, .now from another, as to the accuracy of most of the results: hence I give but a few, those which were reached without mishap, and with proper observation of the various precautions. The difficulties encountered are referred to again in Section 6. The investigation was carried out in the metallurgical laboratory of the Massachusetts Institute of Technology, and part of. The

Jan 1, 1890

By Frank Firmstone

The material described below was made at Furnace No. 2, Longdale, Va., Oct. 28, 1907, during a sudden derangement of working, in the course of which the furnace became entirely bridged over and for some time no solid material whatever descended into the hearth. This caused the hearth to become so completely emptied that, at the tuyere-level, a pricker put in at one tuyere could be seen by looking in at the opposite one. The tap-hole was opened and the iron got out with some difficulty. It ran sluggishly, throwing many sparks, but was not

Jan 1, 1909

Several of the current concepts of brittle fracture involve consideration of, the existence of defects or flaws. Griffith 1 observed that the tensile strength of brittle materials was several orders of magnitude less than might be expected from the calculated strength of the molecular bonds. He was able to show that the stress concentration at the tip of an elliptical crack is sufficient to raise the local stress level many fold. He therefore proposed that real materials do contain such stress risers in the form of minute cracks and that this accounts for the rather large difference between theoretical and actual strengths of brittle materials. The degree of stress magnification depends to a great extent upon the orientation of the crack with respect to the general stress system, and to the general geometry of the crack. It is but a small step to extend the theory to include flaws and defects of other sorts which, though they may be less tractable mathematically than cracks, may still function as stress risers in a real sense in real materials. Brace 2 proposed that the application of the Griffith theory to rock material could be tested in two ways: "(a) by finding the orientation of cracks from which macroscopic fractures have developed and (b) comparing failure strengths from tests at different conditions of loading." In 1963 the author and coworkers at the Bureau of Mines, Twin Cities Mining Research Center, working on a problem involving relationships between strength, sonic velocity, and microstructure "eveloped an experimental technique to examine several somewhat similar questions; namely. does the frequency of occurrence of actual or potential stress risers dictate the relative strength of the material as proposed by Weibull;4 can actual flaws or defects in the rock structure be identified and related to strength and perhaps other properties in accordance with Griffith&apos;s theory; and is the anisotropic strength and elastic behavior of certain rocks related to the preferred orientation of these actual or potential stress risers? The experimental approach developed to answer these questions appears equally applicable to the testing of Griffith&apos;s theory as proposed by Brace. Basically the approach consists of a series of point-load tensile tests followed by petrofabric examination of thin sections prepared from the specimens in order to identify and apply a quantitative measure to microstructural defects which may have contributed to the failure process. In the point-load test, tensile stresses are induced by a compressive load applied to the center of a disc-shaped specimen by means of two opposing hemispherical indentors. Failure generally occurs as a single fracture parallel to the axis of loading and bisecting the disc. Because of the geometrical symmetrical the induced tensile stresses are symmetrical about the loading axis

Jan 1, 1967

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC and was installed on a shuttle car in a conventional room-and-pillar mining section. The purpose of the study was to evaluate proposed legislation that would require shielding on low-voltage trailing cables. Such legislation would require machine modifications to cable reels, packing glands, and couplers; increase cable splicing complexity; and necessitate additional splicing materials and training. Furthermore, fault location might be more difficult. Even though shielding will cause some problems for the mine operator, it can reduce electrical shock hazard to mine workers. This paper presents information that mine operators can use to solve most of the problems encountered if they are required to install shielded cables. The in-mine evaluation was funded by the US Bureau of Mines; however, the views and conclusions in this paper are those of the author and should not be interpreted as necessarily representing official policies of the US government.

Jan 1, 1982

By J. Gordon Parr, L. P. Srivastava

DUWEZ1 has shown that pure titanium and pure zirconium transform martensitically during rapid cooling at temperatures about 30° and 15°C re spectively below their To temperatures. Holden et al.2 determined M, temperatures of Ti-Cu alloys by a metallographic technique applied to isothermally treated samples. Their results, superposed on the McQuillan3 version of the partial Ti-Cu diagram are shown in Fig. 1. Sources of metals were: Titanium: Iodide bar; Foote Mineral Co. Ltd. Zirconium: Iodide bar; Foote Mineral Co. LM. Copper: Spectrographic Standard; Johnson Matthey and Co. Ltd. Alloys were prepared by levitation melting under argon to the following nominal compositions:* 0.5, Quenching, at rates to about 8000°C per sec, was performed by cooling in a stream of helium (99.999 pct pure) a 3/64 in. cube of material previously heated by a tungsten coil in a system operating at. 10-5 mm Hg. Cooling rates below 200°C per sec w were obtained by controlling the current to the heater coil. The specimen was supported on a 32 gage Pt, Pt-Rh thermocouple attached through a DC amplifier to an Edin magnetic oscillograph (Model 8082) with a maximum chart speed of 250 mm per sec. Transformation temperatures were read off the oscillograph charts at the location of the beginning of the thermal arrest. The same specimen was quenched several times, and all runs were repeated on new samples. Regular calibrations of the oscillograph against a potentiometer were made between quenching experiments. The criterion of martensite formation was the effect of surface rumpling. Previously polished samples that showed a rumpled surface after transformation are assumed to have undergone martens itic transformation: transformations of a diffusion type produce no surface disturbance, Figs. 2 and 3. Electrochemical measurements were made in a cell described elsewhere4 whose electrodes were the martensitic and the diffusion-transformed materials in the following electrolytes:

Jan 1, 1962

By J. R. Long, C. E. Armantrout, A. H. Roberson, T. R. Graham

The preparation and fabrication of copper-manganese-zinc alloys and the evaluation of their engineering properties have for some time been an integral part of a research program of the Federal Bureau of Mines. In this project, the use of electrolytic manganese, along with high purity copper and zinc, has permitted the preparation of alloys which contain a minimum of impurities which are capable of producing detectable effects in the properties studied. The initial work on the physical properties of wrought alpha solid solution alloys and a general outline of the alpha solid solution area for alloys containing up to 40 pct manganese have been presented in previous reports. 1,2,3,4,5 The evidence accumulated in these investigations clearly showed that additions of manganese to the copper-zinc alloys improve the strength properties of the brasses without seriously reducing their characteristic ductility and that considerable quantities of manganese could be added to the copper-zinc alloys without exceeding the mutual solubilities of manganese and zinc in copper. In continuation of these studies, additional data have been obtained in a more extensive investigation of the phase relationships of the copper-manganese-zinc ternary system. The present report delineates the solid phase boundaries of the ternary system from the copper-zinc binary to the manganese-zinc binary for alloys containing up to 50 pct zinc. Summary The alloys used in this investigation were conditioned by working schedules designed to homogenize the structures prior to heat treatments required for the equilibrium phase sludy. The treated alloys were examined by metallographic methods including hardness and X ray data for confirmation. The composite data of the investigation are summarily presented in a series of isothermal sections of the ternary system at 1100, 1200, 1300, 1200, and 1500°F. The salient features of the system as outlined by these data are: (1) the continuous alpha solid solution which extends across the diagram to the gamma-manganese phase of the manganese-zinc system at temperatures of 1200°F and higher, (2) the beta phase of the copper-zinc system similarly forms a continuous solid solution with its counterpart the beta field of the manganese-zinc binary, (3) at 1100°F (593°C) these alpha and beta fields are greatly restricted by complications arising from the allotropic transitions of manganese and the decreasing solubility of manganese in the alpha solid solution. The alpha + beta fields intersect the alpha + alpha manganese field to produce the beta + alpha manganese field and two adjacent three phase fields consisting of alpha + beta + alpha manganese and gamma + beta + alpha manganese. Typical microstructures representative of the various phase areas at each temperature are also presented. Review of Previous Work The copper-manganese-zinc alloys have periodically been the subject of numerous investigatioris of both prac-

Jan 1, 1950

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y&apos; (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y&apos; morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y&apos; precipitate in

Jan 1, 1967

By H. F. Yancey, O. L. Furse

For several years the Bureau of Mines at its Northwest Experiment Station, in cooperation with the Mines Department. of the University of Washington, has been studying the breakage and degradation of coal. The first phase of the study was devoted to the determination of the friability of many coals of various ranks and comparison of various methods for estimating friability.&apos; A study of the relative ease or difficulty with which various coals are reduced to the fine size required for use as pulverized fuel followed the completion of this work. Baltzer and Hudson2 list twelve research organizations in the United States, two in England, one in Germany and one in Canada that are reported to be engaged on this problem; showing the general appreciation of the need for a simple method of estimating the grindability of different coals. Hardgrove,3 ho has advanced a method for estimating grindability, points out that pulverizer tests of different coals are incomplete and unsatisfactory. He compares such tests to that of a boiler test made without knowledge of the calorific value of the coal. Frisch arid Holder4 also stress the same point. They state that,

Jan 1, 1934

By C. B. Clark, W. H. Bruckner

Since the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Mun-roe more than 50 years ago (in 1888). Details of their design have been explained elsewhere.1,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense Pressures exerted when the explosive charge is detonated. Among the conclusions reached in research On shaped explosive charges, the following have been established concerning cavity liners:1&apos;2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the &apos;One as well as On the base diameter of the charge. Acute apex angles require thinner walls for optimum perfmnance and more obtuse angles require thicker walls for the same base diameter&apos; 2. Cones were more effective in forming a penetrating jet when the walls were tapered; that is, the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical properties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2, Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1949