Search Documents

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By H. S. Rankin, E. C. Houston

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By Nicholas T. Camicia

Coal is one of our oldest known commodities. Historic evidence indicates that this fossil-formed fuel was used in China and in Wales some 3000 to 4000 pears ago. Coal was discovered in North America in 1679 by French explorers in northern Illinois, and in 1700 a colony of Huguenots came across bituminous coal in Virginia. One might think by this long history of a single commodity that the string was about played out. Quite the contrary, coal is in greater demand than ever before and coal mining today is a modern industry. It is in an unprecedented growth period as the nation-and the world-demands more and more energy coincident with dwindling reserves of other fossil fuels. By the year 2000 the demand for coal is expected to at least double the current level of some 600 million tons annually despite the advent of nuclear power. To meet this challenge, the coal industry is vitally in need of an increasing supply of technically trained and progressive manpower. And, coupled with a serious shortage of engineers and technicians, it represents a rich vein of occupation opportunities-all the way up to top career levels. Today, coal mining is a complex, highly specialized industry concerned with more than just getting coal from the earth and putting it into the furnaces of the consumer. The industry is concerned with the environment, with maintaining a viable ecology. Recognizing the ramifications of global economics, the industry is very much aware of its important position in contributing to a constantly rising standard of living throughout the world. The key to rewarding employment in the coal industry is skill-skill that has been developed by education, training, and experience. None of these alone is enough; all three are necessary today to produce the skill needed to meet the employment requirements of the coal industry. Routine manual labor will no longer do the job in coal mining. In the United States coal mining has been mechanized to a degree unsurpassed anywhere else in the world, and the coal worker must be thoroughly

Jan 1, 1973

F. WEIMER,* Washington, D. C. (written discussiont).-For electrical measuring instruments, especially those types that involve the Wheat-stone bridge or potentiometer principle and standards of electrical resist-ance, there has been, for a considerable time, a need for better resistance materials. For a satisfactory resistance material, much depends on the purposes for which it is to be used. For potentiometers and Wheatstone bridges, such as are in more or less general use, and the more common forms of resistance standards, a good quality of manganin answers fairly well. However, it should not be presumed that manganin is considered ideal for the purpose, for in measuring instruments and resistance stand-ards, there is still much to be desired. An experience of more than 10 years in the study of the resistance standards and resistance apparatus shows that manganin resistances change with time in a way that is very annoying and the maintenance of the unit of resistance to the desired accuracy requires an excessive amount of work or may be said to be prac-tically impossible. The changes in resistance are generally most rapid and erratic in resistances of very low and very high values. In resist-ances of low value, the resistance material is often in the form of thin sheets so that the surface is large and usually more or less unprotected from the atmosphere, or the oil in. the case of oil-immersed standards. In resistances of high value, the resistance material is in the form of fine wire and, therefore, the surface is large compared with the cross-section. In resistances of medium value, the surface is less, compared with the cross-section, or better protected, usually by a silk wrapping impregnated with shellac. This suggests that one of the difficulties with manganin is slow surface action or oxidation, even when an effort has been made to protect the surface from such action However, the changes observed cannot all be accounted for on this basis. There are, presumably, also some internal changes in the resistance material even when it has been annealed. Further; the changes in manganin resistances seem to be more or less independent of its electrical properties. In other respects, too, manganin is not ideal.

Jan 11, 1919

By Thomas F. Downing

When examining a coal property it is customary for the engineer to take channel samples at several coal faces. In doing so the extraneous matter, or partings, which can be removed by hand, or mechanically, with the facilities at hand, or proposed, is rejected. Where there is doubt concerning a stratum it is usually rejected from the main sample but part is taken for separate analysis. The samples are forwarded to a chemist for proximate analyses and determination of British thermal units, and, sometimes, ash fusion. Consideration is given all available commercial analyses but frequently the owner presents only the favorable ones. From the results thus obtained a general evaluation is made, monies are loaned or expended, markets are determined, and realization is estimated. In many instances, such grades are not substantiated and it is time we looked deeper for a basis which will prove more practical. Institute committees are working hard on analytic and use classifications and much valuable information has already been assembled and distributed. However, no single grade can be applied to any particular bed or region. Much study has been given the Pittsburgh No. 8 seam, yet that bed is subject to material differences in a single section;i. e., some strata of a face may differ from others in structure and analysis, particularly in sulfur content. From some localities it yields a good carbonization fuel, while in others it is chemically unfit for such use. Traveling south to the Logan, W. Va., field we find the Cedar Grove (Island Creek) seam a hard, gray splint coal., In the same field, and not far distant, the same bed changes, both structurally and chemically, and consists of excellent gas coal. In Illinois the moisture content of a bed may vary greatly in different localities. We have seen mines in which part of the coal is excellent for special purpose use but is spoiled by the product from another part of the same mine. Many other illustrations could be given but these are sufficient to show that application of any grading of coal must be distinctly local. The actual designation of grade can be given only after detail study of the component parts of the seam, or seams, on the property under considera-

Jan 1, 1932

By T. C. King

AT the new Graham-Central Mill of Eagle-Picher, near Galena, Ill., material is simultaneously dewatered and introduced into the ball-mill scoop boxes by the use of variable-speed, 24-in. spiral classifiers. This arrangement has proved satisfactory in that the moisture content of the wet feed is reduced, thus allowing maintenance of density within the mills, and a constant feed at any desired rate to the mills is provided. In this mill the primary feed is wet crushed to minus ½ in. and preconcentrated by jigs to produce a bulk lead-zinc-iron concentrate and a waste tailing. The jig concentrate is then dewatered by a conventional dewatering classifier and stored in, bins ahead of the ball mills. Even though this material is well dewatered, the discharge at the bin bottom is sloppy because of the gradual drainage of the water from the surface of the particles. Conventional belt feeders with vertical cutoff gates are unsatisfactory because of the flushing characteristic of the wet sand.

Jan 1, 1950

By W. R. Ingalls

The manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been done chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the re-verberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood, and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Con City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose. Just as zinc may be burned off in a blast furnace, so also may it be done in a reverberatory. Indeed, there is less trouble, in some respects, in a reverberatory, for therewith there is no shaft in which accretions may

Jan 1, 1918

By H. R. Brannon, F. M. Perkins, Weldon O. Winsauer

Both the abnormal resistivity exhibited by shaly reservoir materials and their potential are due to adsorption of ions. Interrelationships between the two have been derived and verified by laboratory results. These relations which have resulted from this work may be used in a qualitative manner to estimate whether or not a particular shaly reservoir contains hydrocarbons, and also to estimate the porosity of shaly sands. INTRODUCTION In spite of the progress which has been made in the last decade toward a better understanding and utilization of the electric log, there remain a number of problems in the interpretation of the log. One of these which is often troublesome is that of divining the nature of the fluids in sandstones or carbonate rocks which contain appreciable amounts of shale. It was shown by Patnode and Wylliel in 1949 that shaly rocks exhibit an abnormally low resistivity when saturated with solutions of low ionic concentrations. This phenomenon has been demonstrated to be due to the adsorptive properties of shale or clay in the rock.' In estimating the fluid content of shaly sands or carbonates from the electric log, it is desirable and sometimes necessary to correct for the abnormally low resistivity. A similar correction is likewise often necessary if attempts are made to estimate the porosity of a stratum from resistivity measurements. The correction may be made from data obtained on core samples and from information on salinity of interstitial water. Cores, however, are not always available. Moreover, even if cores are at hand, their examination is time-consuming. It would be most desirable, therefore, to make corrections of this nature from the log itself. Since both the abnormal resistivity and the potential' are consequences of the adsorption of ions on shale, it should be possible to utilize the potential curve to give better interpretation of resistivity data obtained in logging shaly materials. The work described in following sections was directed toward this end. THEORY Relation of Resistivity of Shaly Reservoir Rock to Adsorpttve Properties In discussing the effect which the presence of shale or clay exerts on the resistivity of a reservoir rock, it is convenient to make use of the resistivity factor.4,5 This quantity has been defined as the ratio of the resistivity of the rock when it is completely saturated with an electrolyte to the resistivity of the electrolyte itself. When the rock, such as a clean sand or carbonate, is free of shale the resistivity factor is virtually independent of the ionic concentration of the electrolyte used to saturate the sample, so that F = R0/Rw = constant for a clean rock . . (1) where F is the resistivity factor, R0 is the resistivity of the rock saturated with electrolyte, and Rw is the resistivity of the electrolyte. When the rock contains argillaceous material, the resistivity factor as defined above is no longer independent of the concentration of the electrolyte used to saturate the rock, but decreases as the ionic concentration of the electrolyte decreases. In explanation of this behavior, it is instructive to consider a sample of shaly porous rock placed in contact with a large volume of a dilute electrolyte. The sample is considered to become saturated with the electrolyte, and to attain equilibrium with it. As a result of adsorption by the shale surfaces within the rock, there is a greater concentration of ions in the solution adjacent to the shale particles in the interstices of the sample than there is in the external solution with which the

Jan 1, 1955

By R. Pakalnis, J. P. Savely, R. D. Call

A simple and inexpensive clay imprint core orienting device has been developed by Dr. R. D. Call. It has a minimum of moving parts, is durable and easily used by drillers, and adds only 15 minutes to a core run. Conventional wire-line drilling and a drill hole inclined 30° to 60° from the horizontal plane are required. The device will not operate in a vertical hole. The orientor is an eccentrically weighted downhole device which can be constructed in a mine shop from an old inner core barrel and lead. Modeling clay is packed in the core lifter case, which is screwed on the downhole end of the orientor. A clay imprint of the bottom of the hole is taken after each coring run. This imprint is matched to the top of the succeeding core run, the drill core is pieced together, and a reference line representing the drill hole is scribed on each core. Fracture attitudes are measured relative to the reference line and the core axis. On recent drilling projects, tests for imprint reproducibility were conducted. The results of these tests show an average variation of f3" in location of the scribed reference line between imprints. Comparisons of surface mapping data with oriented core data are good. It is rare that the entire length of drill core in intensely fractured zones can be oriented because it is impossible to piece the core together. However, if a triple tube set-up is used, a modification in the scribing procedure can result in a good statistical sampling of the fracture population. Attitudes of major structures have been oriented with this technique.

Jan 1, 1983

The Rio Tinto - Cerro Colorado operation was the first major cyanide plant built out of South Africa since the Carlin and Corte mills came on-stream in 1965 and 1969. Its flowsheet was presented in the original monograph, "Gold and Silver Cyanidation Plant Practice, " published in 1975, with a brief description of the plant but without the operating costs. The authors have recently received these data and it was believed worthwhile to present them in this volume along with the aforementioned flowsheet. The Cerro Colorado ore deposit is located at Minas de Rio Tinto in the province of Huelva, Spain, approximately 88 km (55 miles) north- west of Seville. The previously mined copper ore bodies lie on either side of the deposit which is mainly copper ore. The crest of the deposit is a capping of "gossan" containing hematite, limonite, gold, and silver. Separate facilities for primary crushing, concentration of copper ores and cyanidation of gold-silver ores are provided. Fine crushing is common to both ores. The run-of-mine open-pit ore is fed from a stockpile via a surge bin and apron feeder to a jaw crusher. After crushing to minus 150 mm (6 in. ), the ore is washed in a rotary scrubber to remove the clay material ahead of fine crushing. Minus 6 mm (1/4 in. ) screen undersize is pumped directly to the grinding circuit with the screen oversize being crushed to minus 19 mm (3/4 in. ) for feed to the primary ball mill; this is followed by two subsequent stages of ball mill grinding to 80% minus 43 microns (325 mesh). Grinding is with water only; no cyanide is used. After thickening, lime is added to the first two of seven Pachuca tanks for conditioning ahead of cyanide addition in each of the five remaining Pachuca tanks. This flowsheet indicates rapid cyanide consumption and the need to maintain a high strength cyanide solution for silver extraction. Agitation for dissolution of the gold and silver is followed by standard CCD practice employing four 67 m (220 ft) washing thickeners in series, with repulping between each thickener. A departure from American and Canadian practice is the use of Stellar filters developed in South Africa for pregnant solution clarification and recovery of zinc-gold-silver precipitates. The precipitate is treated with acid for zinc removal, the sludge filtered in presses, dried, calcined and smelted to produce dore bullion of 900 fineness containing 12% gold and 78% silver.

Jan 1, 1981

By A. W. Brune

Conventional methods of calculating the duty cycle of a mine hoist are awkward in that a number of items must be remembered or that they must be collected together in order to have all the calculated data in one place. A more convenient way is to tabulate all factors involved, permitting a ready evaluation of the problem. An example illustrates the convenience of such a table for either of two types of drums, cylindrical and conical. Assume the following conditions: The hoisting depth is 600 ft. Balanced hoisting is used. The weights of empty skip and ore are 6000 lbs and 12,000 lbs, respectively. Production is 3600 tons per shift. Net hoisting time per shift is six hours with a rest period of eight sec, top and bottom, per trip. Acceleration and retardation are each six sec. The diameter of the drum is seven ft; its face is four ft. The sheave has the same diameter. The equivalent effective weight of the drum reduced to rope center is 15,400 lbs. The weight of each sheave is 2100 lbs. 1 The rope is 1 1/4-in. improved plow steel weighing 2.50 lb per ft.

Jan 9, 1961

By William G. Pariseau

There are important phenomena in rock and soil mechanics that cannot be explained in terms of theories of homogeneous, isotropic materials. Subsidence of strata about mine openings is an example. In-situ stress measurements in nonisotropic sedimentary and metamorphic rocks is another. Patterns of joints, faults, fractures, and similar geologic features impart directional mechanical properties to rock masses that are locally isotropic or anisotropic. On the geologic scale, the nonhomogeneity of composite rock masses may, in certain instances, be dealt with as homogeneous anisotropy. The mechanics of large rock masses can, therefore, be expected to involve considerations of anisotropy. The source of the anisotropy is not relevant. Once the scale of observation is selected and the material is defined accordingly, the analysis of stress and deformation proceeds without regard to the numerical values of the material constants. There are also important phenomena in rock and soil mechanics that cannot be explained in terms of linear elasticity, theory. For the mechanical description of anisotropic geologic materials capable of deforming beyond the limit of purely elastic strains, a plasticity theory is required. The purpose of this chapter is to present a plasticity theory for anisotropic rocks and soils. The proposed theory is based on the work of Hill in anisotropic metal plasticity and represents an extension of his work so as to include anisotropic geologic materials. The point of departure from metal plasticity theory begins with the inclusion of the normal stresses as linear terms in the yield condition, which plays a central role in plasticity. Once the yield condition is established, the plastic strain increments are obtained immediately through the principle of normality. For practical applications, some simplification of the three-dimensional theory is re-

Jan 1, 1972

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

By V. F. Leferrer

A new process for the treatment of silver crusts from desilverization of lead has been developed by Societe de Penarroya. The zinc contained in the crusts is recuperated by vacuum distillation at low temperature. The use of special retort crucibles is avoided. AT Noyelles-Godault the Parkes process (zinc addition to a silver-bearing lead melt) is used to desilverize lead bullion from the blast furnace. The crust which rises to the surface of the bath is removed and pressed by a well-known process in a press of the Howard type. The pressed crust, called zinc crust or silver crust, contains 10 pct Ag, 30 pct Zn, and 60 pct Pb. It is melted under a salt bed in a small, narrow, and deep kettle heated only in its upper part. A liquid concentrated alloy is obtained which is called T.A.C. in France (triple alliage concentr6) analyzing approximately 25 pct Ag, 65 pct Zn, 8 to 10 pct Pb, and 1 to 1.5 pct Cu. This T.A.C. is a real metallic alloy, completely deoxidized, and can be stored indefinitely. The process used at Noyelles-Godault consists in distilling this alloy in a tight furnace, under low vacuum and at low temperature, so that only the zinc distills and is condensed into liquid form. The residual silver-bearing lead is almost entirely free from zinc and oxidized dross. The vacuum dezincing equipment, see Figs. 1 and 2, consists of: 1) A furnace, constituted of a casing of steel plate lined with refractory bricks, heated internally by means of graphite resistors. The temperature of the furnace is measured by a thermocouple device and controlled by an automatic temperature regulator which acts upon the flow of the current passing through the resistors. Two doors, numbered 1 and 2 in Fig. 2, are provided for, one for charging the T.A.C., the other for tapping the high silver-bearing lead. 2) A condenser, and an ordinary room lined with good heat conductor refractory material. This condenser is provided with a graphite resistor which serves to bring to temperature when starting the furnace. A thermocouple records the temperature of the zinc melt and controls the temperature in the furnace, that is, the flow of current through the resistors, by means of the above mentioned regulator, so that the distillation rate in the furnace does not exceed that of the condensation. The condenser is connected to the vacuum pump by a filter. The whole equipment should, of course, be fluid-tight. The operation is carried out under a vacuum of about 10 mm Hg.

Jan 1, 1958

By Rush Sill

THE processes of superficial alteration depend on physical conditions, environment, geologic history and chemical and mineralogical composition. Superficial alteration is confined particularly to the zone of shallow circulation, as this is the zone of solution; its rocks are open and the circulation within it is compara-tively rapid. The enrichment of ore deposits in this zone, therefore, is of special interest. The depth of the vadose, or zone of shallow circula-tion, is variable, because its lower limit depends on the variable level of ground water. In moist, hilly countries its depth varies from a few feet to several hundred feet. In arid regions where the rainfall is low and evaporation great, this zone may extend to much greater depths. Permeability of the deposits . is essential to the downward migration of metals. In rocks, that have been fractured since the primary ore was deposited, there is generally more extensive and deeper enrichment than in ore deposits that have been but slightly fractured. A warm climate increases chemical action and abundant rain fall is favorable to enrichment. Low relief and slow erosion give long periods of weathering and thorough leaching.

Jan 9, 1922

By E. A. Slover

THE usual reverberatory system of smelting cop--1- per concentrate or calcine has for its component parts a furnace and one or two waste heat boilers. These parts are operated on a basis of compromise, since the furnace can send gas to the boilers at too high a temperature and the boilers by plugging, due to dust or slag, can place a definite limit on the amount of fuel the furnace can burn. Over the years the copper concentrate smelting furnace has had few advances in design. The simple rules of design such as the flame should wipe the bath and the speed of the gases should be reasonably low for dust carrying purposes seem to cover the main features. In the construction of the individual furnaces some innovations are always being introduced. Among these are charging so that the work of smelting is a complete bath process, the use of suspended brick arches in place of sprung arches, the use of basic brick, not only in the crucible, but also in roof and sidewalls, the use of various means to feed the charge, the use of magnetite or other heavy material to construct the hearth, water cooling of bridgewall and slag skimming bay, the smelting of raw charge instead of calcine, the use of preheated air, and possibly the use of oxygen-enriched air for combustion. But the general outlines of the furnaces have not changed much except as to size. Furnaces at Hurley As shown on Fig. 1, the furnace at Hurley is 126 ft long between the longitudinal buckstays and 32 ft wide at the skewback plates. The foundation is a concrete retaining wall with piers at intervals that go deeper into the earth. Purposely the wall at the burner end of the furnace is not backed-up as tightly as the other parts of the foundation so that movement due to expansion may take place here rather than into the boiler foundations. Within these foundation retaining walls of concrete, the earth has been removed to allow the placement of the crucible brick base inside of which a silica hearth is laid 4 ft 6 in. in depth. No expansion is left in the brick base and crucible where they are in contact with the hearth. The hearth itself is of quartzite crushed to 1 in. size with fines left in the product. An 8 in. layer is laid and tamped with paving tampers to about 6 in. in thickness. Then a layer of silica flour is spread and vibrated into the hearth. This operation is repeated until a depth of 4 ft 6 in. is occupied by the silica mass onion-skinned in layers of approximately 6 in. Before firing the entire hearth is covered with broken slag to a depth of 4 in. so that a seal may be formed on the hearth. The crucible is completely faced with magnesite chemically bonded brick while the outside, against the foundation, is made of silica brick. The side-walls are carried up with silica brick in which expansion joints are left at intervals. Above the crucible the sidewall is corbelled to form a shelf on which the charge may build up along the side-walls, see Fig. 2. The arch of the furnace is sprung 20 in. silica brick, with the longitudinal centerline horizontal the length of the furnace, and some 9 ft in the center above the bath. Both straight and wedge brick are used in the construction and a thin silica mortar is troweled for joints. After the arch under heat has assumed its permanent shape, a silica slurry is spread over the arch to fill any cracks that have formed, thus giving bearing surface to the brick and preventing dust from entering the body of the arch to act as a future fluxing agent. The uptake of the furnace slopes up to the boiler entrance where a brick pilaster divides the gas stream for the two boilers. Over this flared uptake is a suspended flat arch of firebrick. The pilaster and sidewalls are constructed of firebrick but the bottom of the uptake is lined with silica brick and fettled through holes in the roof with siliceous fettling. Close to the entrance of each boiler is a brick covered slot through which water-cooled dampers may be lowered in event of boiler trouble. These water-cooled dampers are hung permanently in position ready to be lowered when needed. Flexible hoses to follow the dampers as they are lowered are connected at all times and individual chain blocks are used to lower the dampers. A pump supplying water is started before the dampers enter the heat. Charging of the furnace along the sidewalls for some 80 ft from the bridgewall is accomplished by electric vibrating conveyors fed by belt from charge storage bins above the furnace. These conveyors

Jan 1, 1954

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is also used as a high value- in-use sand blasting agent and as a premium grade foundry sand. It is produced by E. I. du Pont de Nemours & CO. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about 36 of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. Staurolite production is approximately 100,000 net tpy. No other commercial production of staurolite is known. This process yields staurolite concentrates of the characteristics given in [Table 1]. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required

Jan 1, 1975

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytical expressions derived previously are used to describe quantitatively effects on macrosegregation of some solidification and mold design variables. Al-4.5 pct Cu alloy is used as example. It is shown that abrupt changes in heat transfer rate result in solute-rich or solute-poor "bands". Severe solute-rich bands accowzpany "reheating" that can result, for example, from abrupt formation of an air gap at a mold-metal interface. With planar isotherms, solute-poor regions also result from reduction in cross section through which fluid flow to feed shrinkage takes place. It is suggested that the negative "cone" of segregation often found at the base of large ingots results from this reduction in cross section for feeding. Consideration is given to the positive and negative segregation to be expected in laboratory ingots in association with changes in ingot cross section. Under-riser positive segregation is considered and it is concluded this segregation results when vertical temperature gradient is low in the region of the riser; the segregation is accentuated by the temperature gradient reversal which can occur in inadequately insulated risers ("'hot tops"). Finally it is shown for Al-4.5 pct Cu alloy that the assumption of constant k and p in analytic solutions gives calculated results close to those obtained for the case of ziariable k and 0. A basic "local solute redistribution equation" was derived earlier' for calculation of macrosegregation resulting from flow of solute-rich liquid to feed solidification shrinkage, thermal contraction, and/or other contractions occurring during solidification. This expression relates fraction liquid, g~, to liquid composition, CL, at a given position x, y, z, in a solidifying Eq. [I] is for the general case of three-dimensional heat and fluid flow assuming constant solid (but not necessarily liquid) density during solidification, negligible net solute change from diffusion, and no pore formation. In this paper we first demonstrate application of this equation for calculation of macrosegregation in several examples involving one-dimensional heat and fluid flow. Specifically considered are examples in which segregation results from sudden changes in heat flow conditions. Next, Eq. [I] is used to describe segregation in examples where isotherms remain planar but where fluid flow is no longer one-dimensional. Application of this expression illustrates the type of segregation to be expected in unidirectionally solidified ingots of gradually or abruptly varying cross section. For segregation calculations, A1-4.5 pct Cu alloy is employed with constant k and p Vz = 0.172, 4 = 0.055), eutectic composition (CE = 33 pct Cu). In all examples, fraction eutectic is neglected in velocity calculations; this was previously shown to introduce little error.' A linear distribution of fraction liquid in the liquid-solid zone is assumed. In a concluding section it is shown that the assumption employed of constant k and /3 gives results close to those obtained when the actual (variable) values of k and 0 are employed.

Jan 1, 1969