Search Documents

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.' Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train' The 'ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By T. A. O’Hara

SINCE May 1948, when tungsten carbide bits were introduced at the Flin Flon mine, they have been popular with the miners because of their fast drilling speed and low gage loss. The high cost of commercial carbide bits and tipped drill steel, however, prevented their use except for the hardest rock. In an effort to extend the use of tungsten carbide on a basis economically competitive with detachable steel bits, experimental work was begun in 1950 to test the feasibility of making tungsten carbide tipped drill steel in the mine drill steel shop. This work showed that tipped drill steel could be made locally at less than half the cost of the commercial product. The performance of the local tipped drill steel was comparable to that obtained with commercial carbide bits and tipped drill steel and the cost per foot drilled was much lower. Local tipped drill steel was adopted for all mine drilling in November 1951. Since then drilling costs per foot have been sharply reduced and footage drilled per manshift has increased markedly. Experience at Flin Flon has shown that production of satisfactory carbide tipped drill steel is not difficult and that highly skilled labor and costly equipment are not required. As long as wise selection of brazing materials is made and certain simple precautions are rigidly maintained, there is no reason why small mines with relatively unskilled labor cannot produce a satisfactory product. The following description outlines the technique used at Flin Flon for making carbide tipped drill steel and discusses characteristics of the brazing process that make special precautions necessary. Drill steel is forged to four-wing shape in a conventional steel sharpening forge. Standard steel dies are modified to minimize forging cracks around the central waterhole and to forge a blunt bithead on the steel. The steel is preheated to 1500°F and held at this temperature for at least 2 min. When the temperature has equalized throughout the steel section, the drill steel is transferred to the forging furnace and heated rapidly with a reducing flame up to 2000°F. This two-stage method of heating minimizes the grain growth and decarburization of the steel while ensuring that the steel temperature does not vary greatly throughout the forging zone. After forging the steel is allowed to cool in air to about 1600°F before being annealed in a bath of vermiculite. Despite the high hardenability of the 3 pct Ni-Cr-Mo drill steel used, this simple treatment anneals the drill steel sufficiently for milling. The forged and annealed drill steel is slotted on a plain horizontal milling machine that is equipped with a quick opening chuck and a slot depth stop. The full depth of the slot is milled in a single pass of the 3-in. milling cutter which is fed at 33/4 in. per min across the crown of each bit wing. The slots are cut to a width of 0.342 to 0.344 in. Maintenance of this slot width is necessary to ensure that the optimum brazing clearance of 0.002 in. will result after assembling of shims and carbide in the slot. Prior to March 1953, when the milling machine was installed, drill steel was slotted on a small manually fed ¾ hp milling attachment mounted on the bed of a lathe. Over 16,000 drill steels were slotted on this unit, and in view of its small size and low cost it gave excellent service. Brazing of Tipped Steel Drill steel that has been milled and cleaned in carbon tetrachloride is mounted in a rotating cradle holding six drill steels, the length of which may be from 2 to 12 ft. The slots in the drill steel, the shims, and the tungsten carbide inserts are thoroughly fluxed with a fluoride flux and assembled as shown in Fig. 1. Fig. 2 shows the brazing equipment in use. As the ring burner is lowered over the bithead a spring valve opens the gas lines, and the gas mixture, preset to give a slightly reducing flame, is fed to the ring burner where it is lit from a pilot flame. The ring burner heats the drill steel over a zone about 1 to 2 in. below the bithead, which becomes heated by conduction through the steel. By this means the bithead is heated rapidly and evenly, and contamination of the brazing joint with soot from the flame is avoided. The bithead is heated to the melting temperature of the brazing alloy within 1 min. This rapid heating minimizes the disadvantage of a non-eutectic brazing alloy. The brazing alloy, a nickel-bearing quaternary alloy, is placed at the bottom of the slot below the carbide insert, as shown in Fig. 1. As the brazing alloy melts it is drawn by displacement by the carbide and by capillary action into all parts of the joint to displace liquid flux from metal surfaces. As soon as the brazing alloy melts, each insert in turn is wiped by being moved back and forth along the slot. This action assists wetting of the carbide by the brazing alloy and assists in displacing molten flux from the joint. After continuous heating for about 75 sec, when the bithead has reached a temperature of about 1500°F, the ring burner is raised and the gas supply is shut off automatically by the spring valve. As soon as heating is stopped a hand press is placed on the bithead and the inserts are squeezed down firmly. This action minimizes the clearance between the bottom of the insert and the slot. Correctly brazed steel should maintain a clearance at the bottom of the slot of 0.001 to 0.002 in. After six steels have been brazed they are removed from the cradle and allowed to cool in air. As soon as each drill steel is cool it is dressed on a grinding wheel to remove excess flux and braze and is ground to the gage appropriate to the length of the drill steel.

Jan 1, 1955

By R. D. Young, E. A. Harre

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Certain bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent required by succeeding nonleguminous crops. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. These organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen at high temperatures and pressures and in the presence of a catalyst to form ammonia. Modern plants use air, water, and natural gas or other hydrogen sources to produce the ammonia that is now the key building block of the fixed nitrogen industry. Several major problems that developed in the 1970s continue with the nitrogen industry into the 1980s. These are (1) the continuing sharp escalation in the cost of feedstocks for ammonia production as well as all energy sources, and (2) the very steep increase in the investment cost of production facilities. More than 75% of the fixed nitrogen produced domestically is consumed as fertilizers. The types of materials used as fertilizers have changed significantly during the past years. There has been a trend from the use of low-analysis fertilizers to types which contain high percentages of plant nutrients. The average plant nutrient content (N + P2O5 + K2O) of fertilizers used in the United States has increased from 18% in 1930 to 32% in 1960 and today approaches an average of 44%. In the case of nitrogen fertilizers, the low analysis natural nitrates (16% N) gave way to ammonium sulfate (20% N) after about 1920. After World War II, ammonium nitrate (33.5% N) previously used in munitions, became established as the leading nitrogen fertilizer. Urea use as a fertilizer (46% N) began in the 1960s, and in the past 10 years has become the world's leading solid nitrogen fertilizer. Nitrogen Materials Anhydrous Ammonia-Anhydrous ammonia is a colorless gas at ambient temperatures and pressures and has a sharp pungent odor. Anhydrous ammonia is stored and transported as a liquid in high-pressure cylinders and tanks at ambient temperature, and in low-pressure tanks, barges, and ships at -28°F. Anhydrous ammonia is applied directly at 4 to 7-in. depths in the soil as a high-pressure liquid by special applicators, after which it expands to a gas that dissolves in the soil moisture or is absorbed on soil colloids. In other systems ammonia is metered into irrigation water and is thereby introduced into the soil.

Jan 1, 1983

By J. Rogers, K. L. Sutherland

THE relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. EXPERIMENTAL PROCEDURE The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testing18 have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.25 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By K. L. Sutherland, J. Rogers

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By J. Rogers, K. L. Sutherland

The relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. Experimental Procedure The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testingin have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.26 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±o.2 pH units and ±5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By R. W. Guard, M. E. Fine

By treating the dislocation like a surface and ap-plying the usual thermodynamic treatment to the adsorption process a Gibbs adsorption equation for dislocations was derived. For extended dislocations in binary solutions the adsorbed concentration on the fault, X2a, may be computed from (jo/da2b) where a2b is the activity of the solute in the bulk material and s is the stacking-fault energy. Using the data of Howie and Swann for s the adsorption concentration goes through a maximum at 2 at. pct Al in Ag-Al, 10 at. pct Zn in Cu-Zn, and 8 at. pct A1 in Cu-Al. The pinning stress calculated from this concentration difference goes Ihrough a maximum at the same concentration us the peak in X2 a. The computed pinning stress thus does not vary with composition in the manner predicted by Suzuki, as was also pointed out by Hendrickson. The results are compared with the stress increment which can be attributed to Suzuki locking in Cu-Zn and Cu-Al stress-strain curves. They both agree in magnitude and in the location of the maximum. The predicted and observed maximum values for the Cu-Zn system (where activity data are available) are 700 g per sq mm (predicted) and 1000 g per sq mm (measured, laking into account the orientation factor of 2.2 to convert poly-crystalline to single-crystal data). CERTAIN simple internal surfaces may be regarded as dislocation grids. This fact suggested that it might be profitable to consider certain phenomena related to segregation of solute atoms at dislocations from the point of view of the thermodynamics of surfaces and surface adsorption. A general treatment of this type is given and then the results are applied to Suzuki segregation and pinning. Confirmation of the results is obtained from comparison of stress-strain behavior for copper and copper-base alloys. Two kinds of dislocations need be treated: perfect and extended dislocations. In either case the line tension of a dislocation, ?. the work which must be done to increase the length of dislocation by a unit length, is analogous to the surface tension. For an undissociated dislocation ? is the self-energy of a unit length of dislocation; for an extended dislocation where is the self-energy per unit length of a pair of partials far enough apart so that there is no interaction energy, is the interaction energy per unit length, is the stacking fault energy per unit area, and w is the equilibrium separation of the paired partials. In the absence of an applied stress the force pushing the dislocation partials apart in a close-packed structure is Gb2/12p where G is the shear modulus, b is the Burgers' vector of the complete dislocation, and is the separation of the partials. At the equilibrium separation, w this force equals s. Thus

Jan 1, 1965

By W. H. Jr. Meyer

Although an aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph provided some form of radial-line method is used to determine the true position of images. The slotted-templet method, which is based on the well-established radial-line principle, has made it possible to construct accurate mosaic maps at a cost comparable with that formerly charged for the average mosaic. It makes possible the securing of these results with far less ground control, which is always expensive. It has expanded widely the possible use of aerial photographs for mapping. ALTHOUGH a vertical or oblique aerial photograph is not a map, most of the information that is necessary for compiling a map is recorded in the photograph. Some ground controls or data are needed, the number and accuracy to be governed by the mapping method to be used and the scale and final accuracy desired in the finished map.

Jan 1, 1939

By Homer N. Mead

This report develops equations for decline curve analysis based upon the premise that the rate of change of the reciprocal of decline for succeeding time intervals is constant when the reservoir is produced under a fixed set of conditions. A method is shown for predicting maximum production rate against cumulative production for any reservoir. A method is also presented for predicting future production rate by an analysis of past production performance after decline has been esrahlished. INTRODUCTION No significant contribution to the analysis of decline curves by the loss-ratio method has been made since J. J. Arps paper1. The concept of loss-ratio that was developed by Arps and his contemporaries has been redefined in another way and the concept of instantaneous loss-ratio at time zero has been added. In the mathematical developmerit by Arps, production rate was related as a continuous function with time and his equatlons were developed on that basis. In this paper, production is considered to be a series of segments for equal time intervals and equations have been developed based upon these finite differences. It is realized that decline curve analysis is not the answer to all predictions of reservoir behavior. However, as production must decline from an initial maximum rate to zero in any reservoir, if such decline can be expressed as an infinite series, this series should accurately predict production. Decline curve analysis should be considered a valuable tool that may be used in conjunction with predictions of future recoveries by other methods. Various uses of the decline curve method will be discussed in this paper. Equations predicting production rate at any time and cumulative production by exponential and hyperbolic decline will be developed. Characteristic values of b related to various types of drive will be discussed. After that a hypothetical reservoir will be studied and ultimate recovery by natural depletion and pressure maintenance compared, then actual field examples will be shown and discussed. The rate-cumulative curve introduced by H. N. Marshs in 1928 is an important one for use in estimating future production rate and ultimate recovery. This graphical method is the one that is used in conjunction with the equations to be developed for predicting production behavior. EXPONENTIAL DECLINE In exponential decline each succeeding production rate per unit of time is a constant percentage of the production rate just before it. Since (1 — r) is the common ratio, where r is the constant decline rate, this condition may be expressed as a geometrical progression; thus Pn = P (1 - r)n-1 . ......(1) Where r is less than unity, r Since P1 (1 - r)n = Pn+1 P1 - Pn+1 C =P1-Pn+1/r........(2) LOSS-RATIO In this paper the calculation for loss-ratio has been changed from the method presented by Johnson and Bollens2. The first loss-ratio to be calculated is a,; it is the initial production per unit of time after decline has set in divided by the difference between the initial and the second production rate. This loss-ratio is for the first time interval. After b (which is the constant change

Jan 1, 1957

By W. R. Ingalls

THE manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been clone chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the reverberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Canyon City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose.

Jan 9, 1917

By P. R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,' and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.'.' Bunker Hill Co. of Kellogg, Idaho, supplied the ore sample used in these tests. The sample was typical of the ore milled in 1949 and contained 4.52 pct Pb and 1.08 pct Zn. A flotation test made by the author with potassium ethyl xanthate as a collector, the same flotation reagents, and the same grind employed in regular Bunker Hill mill practice was the standard for comparing results with the compounds and derivatives of guanidine. The compounds and derivatives of guanidine are only fair collectors of galena. However, if potassium ethyl xanthate were used in the galena float, its presence later in the sphalerite float would make it impossible to introduce another type of collector and be certain which collector contributed the result, so the compound or derivative of guanidine under test was used in both the galena and sphalerite floats in Table I. On both the galena and the sphalerite in the Bunker Hill ore, the depressing action of sodium cyanide and zinc sulfate is much greater with collectors of the guanidine type than with the xanthates. If the depressing agents are left out when a guanidine type of collector is used, but a pH of 8.6 is maintained with either lime or sodium carbonate, the depressing action is approximately the same as in the standard xanthate test. Consequently the depressing agents, sodium cyanide and zinc, were not used in the galena floats of tests 1226, 1228, and 1286, Table I, so the galena floats would be on a comparable basis with the standard xanthate test. As shown by the tests in Table I, the loss in the tail when diphenyl guanidine is used is 8.3 to 9.3 pct, as compared to 17.6 pct with potassium ethyl xanthate, or a recovery of 2.3 to 2.0 lb more zinc. Concentrate grade is 13.7 pct with potassium ethyl xanthate and increases to 22.9 and 31.8 pct with diphenyl guanidine, showing a much higher selectivity. Unless the Barrett's No. 4 coal tar creosote is considered to be a collector, no collector other than diphenyl guanidine is present in the tests, Nos. 1226, 1228, and 1286. Tests 1218, 1253, and 1263 in Table I1 were run to check the effect of the depressing agents used in flotation of the galena (sodium cyanide and zinc sulfate) upon subsequent flotation of sphalerite by diphenyl guanidine. Urea was substituted for potassium ethyl xanthate in tests 1253 and 1263 because it is a good collector for galena and a poor one for sphalerite, and the effect of the depressing agents is more marked with urea than with potassium ethyl xanthate. Test 1205 checks the effect of urea alone without any depressing agents when used for the flotation of galena. Table I1 shows that diphenyl guanidine as a collector for sphalerite is compatible with other flotation reagents used in floating galena. When the depressing agents sodium cyanide and zinc sulfate are used in the galena flotation step, the amount of lime in the sphalerite flotation must be increased (compare 1253 and 1263). Table I11 gives some of the compounds of guanidine which were tested and compared. Some of the compounds and derivatives of guanidine* are solu- * Diphenyl guanidine is in commercial production and is available on the market. ble in water and others are not. Those tested were fed dry. When an organic collector is promising, its compounds and derivatives should be tested and their comparative collecting power recorded. Eventually, in this way, it may be possible to discover some of the essential chemical characteristics of a good collector. For example, it is interesting to compare the diphenyl and dibutyl derivatives in Table IV with those of urea in Table 111, Example 3, U. S. Patent 2,664,198. All are good collectors. Table I shows some of the effects of lime on recovery of sphalerite by diphenyl guanidine. Table V

Jan 1, 1960

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

By John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 36 tons of water for each ton of coal produced, while bituminous mines average about 5 or 6 tons. Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a mine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. But it must also be controlled long before it reaches this stage. Water standing in the working faces is unpleasant for the men who have to work there and also cuts down on the amount of work they can do, as they must watch where they step all the time. It is especially unpleasant in low coal.

Jan 1, 1973

By Jasinder S. Jaspal, John A. Reeves, Bradley J. Bourquin

INTRODUCTION The United States has an abundance of coal reserves in thick seams. Most of these resources are in the West. Surface mining operations in thick seams are highly efficient, particularly in the West, but methods for mining thick seams underground are very limited. The percentage of resource recovery in deep mining of thick seams is often as low as 30 percent. It is estimated that there are 45 billion tons of coal reserves for underground mining in seams greater than 10-ft thick in the western states alone. With such a large available reserve base and low rates of recovery, the need to develop the technology to mine these thick reserves is quite evident. As the definition of a thick seam varies widely from country to country, a thick seam is defined here as any seam where the height is such that it is not minable in a single pass with available mining equipment.

Jan 1, 1981

By L. A. Panek

During the past three years, USBM has developed an apparatus and technique for direct measurement of existing pressure and change of pressure in mine rock. This relatively simple and inexpensive monitor is reliable for months after being installed. It is used to determine shift of ground pressure created by different sequences of mining, to ascertain the cause of rock failures, and to evaluate the need for artificial support. The technique has been employed to measure pressures in limestone, greywacke, concrete, diabase, and soft iron ore. When rock is subjected to a load it is deformed. Ordinarily this is observed in a mine as the displacement of one point with respect to another—the deflection of the roof, which may be observed as a convergence between roof and floor; or the extrusion of material from the rib, which may be observed as a decrease of the distance between the rib and the post of a timber set. The effect of excessive pressure may be a rockburst if the rock is strong, or it may be squeezing ground if the rock is soft. Some desirable effects of high stress (high in relation to strength) are the caving of roof in a longwall mining operation, the caving of ore in block caving, and the decrease in mechanical energy required to break down the mineral seam in a retreating pillar-robbing operation. In any case, whether the observable effect of rock load is desirable or undesirable, it is a displacement, and depends on the following four factors: 1) The structure—the size and shape of openings, pillars, and linings, the geologic bedding and jointing. 2) The mechanical properties of the rock—prin-cipally the strength, modulus of elasticity, and flow characteristics. 3) The load or applied stress—primary sources are the weight of superincumbent rock, which increases with depth, and unrelieved tectonic stresses; secondary sources are redistributed pressures caused by other nearby openings, especially large mined out zones (rock pressure depends partly on the rock structure created by mining). 4) Duration of load, related to the length of time the opening is exposed. CONTROL OF ROCK DISPLACEMENT Rock displacement can be controlled by control of these four factors. Consider now the means of exercising such control over these factors. Control of the structural features is obviously possible to a great extent, as such control is exercised largely by choosing the method of mining and the methods of natural and artificial support. Rock properties vary, even within a particular mine, but they are controllable only in the limited sense that control may be exercised by choosing the beds or zones to be mined so that rocks with undesirable properties will not occupy critical positions within the rock structure created by mining. Rock pressure is the most complex of the four factors through which ground control can be achieved because it is invisible, difficult to measure, and poorly understood. Rock pressure is controllable only to the extent that control is exercised on the rock structure created by mining. Considering openings within a particular mine, time of exposure varies, and is readily controllable because it is easily measured and easily understood — the longer an opening stands, the greater the likelihood of failure or excessive convergence. Control is exercised by choice of an appropriate sequence of driving openings of different classes, such as haul-ageways and rooms, which are required to remain well supported for different lengths of time under different conditions. Again, control is exercised through the method of mining. All controllable factors can be controlled by proper design of the mining method. The orientation and relative positions of the mine workings and the sequence of their excavation are likely to be much more important to ground control than is the design of artificial support. This implies that the major decisions in regard to ground control are made, knowingly or not, at the time the mining method is chosen. WHY MEASURE ROCK PRESSURE In addition to restrictions on the several factors, control implies the measurement of these factors in some sense, whether only qualitatively by visual observation, or by actual quantitative determination with a measuring instrument. Rock pressure is the most difficult of these factors to measure, largely because of the interaction between the measuring device and the rock. Nevertheless, the quantitative

Jan 1, 1961

By O. Jantti, Erkki Laurila, R. T. Hukki

INVESTIGATION of the methods of analyses for magnetite and ilmenite in the Otanmaki iron-titanium ore and respective mill products has resulted in certain improvements in the methods conventionally employed. The outcome of the investigations is summarized as follows: 1—Development of a diamond-drill core analyser for the determination of magnetic susceptibility of drill cores containing magnetic minerals. 2—Development of a magnetite-ilmenite analyser for pulverized products. 3—Development of a potentiometric method of chemical analysis for the determination of iron, vanadium, and titanium in succeeding steps from one test sample. 4—Proposal for a continuous and automatic magnetite assay method. Diamond-Drill Core Analyser The conventional method of assaying diamond-drill cores consists of splitting the cores, pulverizing them and running chemical analyses on representative samples. The physical properties of magnetic minerals, however, offer an entirely different approach to obtain similar final result by the measurement of respective magnetic susceptibilities in a properly designed instrument. This instrument is shown in Fig. 1. Essentially it consists of a magnetic unit, A, and of a meter unit, B. On top of A is a slot where a piece of diamond-drill core C is visible. The magnitude of disturbance in the original magnetic field caused by the magnetic minerals in the drill core can be observed from the microammeter. This reading is a function of the combined susceptibilities of all magnetic grains in the magnetic field. The magnetic unit is built of E-sheets of a shell transformer, as shown in Fig. 2. The primary coil and two identical secondary coils are wound around the central leg and end legs, respectively. The drill core under examination is placed into one of the air gaps as shown in Fig. 2. The number of ampere-turns of primary coil excited by 50 or 60-cycle ac give a maximum induction of about 600 gauss in the air gaps. The secondary coils are connected in series in the opposite direction. Thus their voltages compensate each other if no drill core exists in the air gap or if the susceptibility of the drill core is equal to zero. As soon as the susceptibility becomes greater than zero, the balance of the magnetic circuit is disturbed, resulting in increased voltage in the terminals of coil 1 and in a respective decrease of voltage in the terminals of coil 2. The voltage difference thus produced is a function of the effective susceptibility of the drill core. If the magnetic grains in the drill core are unevenly distributed, the voltage difference varies as the core is rotated around its own axis. The voltage difference is measured with a Bren-tan0 tube voltmeter. If extreme sensitiveness is desired, the established symmetry of the magnetic circuit does not allow reduction of the 0-voltage difference far enough. Therefore a compensatory voltage of a correct phase taken from the terminals

Jan 1, 1952

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By James H. Courtright, Kenyon Richard

TOQUEPALA is a porphyry copper deposit in which mineralization is localized by a large breccia pipe formed in dose genetic relation to intrusive rocks. The deposit is in southern Peru, 55 airline miles north of the small city of Tacna and the same distance inland from the port of 110. Quellaveco and Cuajone, geologically similar deposits, lie 12 and 19 miles north of Toquepala. Chuquicamata is 400 miles to the south. The deposit is high on the southwestern slope about 20 miles from the crest of the Cordillera Occidental of the Andes Chain. It lies in a mountainous desert where the steep southwesterly slope of the Andes is dissected by a succession of rapidly downcutting, deep canyons. Local topography is moderately rugged with a dendritic drainage pattern and an elevation of 8000 to 14,000 ft. Volcanic peaks along the crest of the Cordillera rise over 19,000 ft.

Jan 2, 1958

By L. B. Gittinger

Sulfur is a nonmetallic element widely distributed in nature. It constitutes 0.06% of the earth's crust but only a very small portion occurs in sufficiently concentrated amounts to justify mining. Sulfur occurs in practically all animal and plant life. It constitutes approximately 0.09% of the elements in the oceans; it has been found in meteorites. Sulfur was known and used by man before recorded history. The American Chemical Society approved spelling for the element is sulfur. The English spelling sulphur is used commercially in the United States. In ancient times, sulfur was called brimstone, literally "burning stone." Today the term brimstone is used interchangeably with the term elemental sulfur. Sulfur is found naturally in the elemental form in subsurface deposits associated with gypsum and anhydrite in salt domes and sedimentary formations in evaporite basins and in solfatara-type deposits associated with volcanoes and mineral springs. Sulfur occurs also in molecular combination in ferrous sulfides (pyrites and pyrrhotite) and nonferrous sulfides (copper, lead, zinc, and nickel), and in mineral sulfates (gypsum and anhydrite); as hydrogen sulfide contaminant in natural gas; as organic compounds in crude oil and tar sands; and as pyrite and organic compounds in coal and oil shales. Sulfur resources are abundant and exist throughout the world but the extent to which they can be classified as reserves is greatly circumscribed by prevailing prices and technology. Estimates of world sulfur reserves are compiled by the U.S. Bureau of Mines. A compilation of reserves by area and source of sulfur published in 1970 and presented here as [Table 1] totaled 2.47 billion tons (Lewis, 1970). The effect of the decline in prices which has occurred since the earlier estimate is dramatically illustrated by the 1972 estimate of the U.S. Dept. of the Interior which shows world sulfur reserves of only 1.2 billion tons (Anon., 1972d). Sulfur is produced commercially from one or more sources in nearly 70 countries of the world. World production of sulfur in all forms totaled 41.6 million tons in 1971. (Sulfur statistics given in this chapter are long tons.) Native deposits, sulfides and oil and gas contributed, respectively, 31, 41, and 25% of world production (Table 2). Of the sulfur produced from native deposits, salt domes accounted for 54% and evaporite basin deposits, 44%. Volcanic deposits are of little significance except for local consumption. The past two decades have seen important shifts in the world's sulfur sources. In 1950, native deposits and sulfides each supplied about one-half of the world's production. During the 1950s, sulfur recovered from oil and natural gas grew rapidly, representing about 10% of the total by 1960. Since then, the petroleum industry has continued to increase its relative importance as a source of sulfur, representing more than 30% at 1972 year-end. Sulfur is generally classified as elemental or nonelemental for statistical purposes. Elemental sulfur is sulfur produced in the pure, uncombined form. It includes production from native deposits, as well as that recovered in the elemental form from oil and natural gas or other sulfur-bearing materials. When produced from other than native deposits, it is generally referred to as recovered elemental sulfur. Nonelemental sulfur is that which is utilized commercially in molecular combination with other elements, such as sulfides or sulfates. Elemental sulfur is being produced from salt dome deposits in the Gulf Coast region of the United States and the Isthmus of Tehuantepec in Mexico, and from evaporite basin deposits in west Texas, Poland, Sicily,

Jan 1, 1975