Search Documents

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By Francis Lucas

A microscope objective of given numerical aperture, whew used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability-the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise whew the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500, µµ and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.65 N. A. are wow an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Köhler and Dr. M. Vow Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 µµ which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 6, 1926

By Francis F. Lucas

A microscope objective of given numerical aperture, when used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability—the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise when the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500 uu and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.60 N. A. are now an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Kohler and Dr. M. Von Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 uu which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 1, 1926

By Lewis A. Smith

Chromium is one of the new metals, but considerable research has been required to determine an approximate record of its production from 1827 until the present. Its use in the form of pure metal is not extensive; of the chromite mined, about one-half is required for making ferrochro-mium, about two-fifths goes directly into refractories and the remainder is absorbed chiefly by the chemical trades. The industries that demand chromite for such uses are mainly in countries that produce little chromite, while the important chromite-producing countries are not generally consumers. The international flow of chromite is therefore of interest, as well as the political and commercial control of resources of the metal. World Production The first mining of chromite is said to have occurred as early as 1820, at the Roros deposit in Norway, but the first well-established output came from the Reed mine, in Maryland, about 1827. Thereafter the United States led the world in chromite production until 1860, when Turkey took the lead. Russia in turn became the chief producer from 1897 to 1902, inclusive. From 1903 to 1909, New Caledonia held first place, but alternated with Southern Rhodesia from 1910 to 1917, inclusive. In 1918, 1919 and 1920-1921, the United States, India and New Caledonia led, respectively. In 1922 Southern Rhodesia assumed first place and has since continued to be the world's foremost producer by a large margin. Fig. 1 illustrates the production of the leading countries from 1890 to 1929, inclusive. Fig. 2 shows the world production of chromite from 1890 to 1929, inclusive, in long tons and Table 2 gives the production by countries for the same period. The total world production for the 103 years, 1827 to 1929, ipclusive, is estimated at about 7,100,000 long tons, distributed as shown in Table 1. World Trade in 1928 In reviewing the figures for the flow of chromite in 1928, it is evident that the six countries that produce most consume little chromite and

Jan 1, 1931

By B. H. Caudle, W. J. Bernard

Factors which influence the success or failure of a waterflood can seldom be determined in the laboratory. For this reason pilot waterfloods are initiated in a repreventative portion of the oil reservoir in question. For a pilot flood to predict quantitatively the recovery to be expected in a field-wide waterflood operation, the pilot area must behave as though it were confined (surrounded by similar areas). In this study, laboratory fluid-flow models were used to determine the simplest pilot pattern, for particular conditions of mobility ratio and initial gas saturation, that would behave as though it were confined. Pilot patterns studied ranged in complexity from a single inverted five-spot to a grouping of nine regular five-spots. Only the innermost producing well in each pattern was studied. Model results showed that the optimum number of wells in the pattern depends upon the oil-water mobility ratio and the expected oil-bank size. Unfavorable mobility ratios will, in general, require more wells in the pilot pattern than will favorable mobility ratios. Pilot patterns in reservoirs which contain a dispersed, flowable, free gas saturation will require fewer wells than for the under-saturated case. The single inverted five-spot pattern was found to be unsatisfactory for predicting behavior of fully developed waterfloods. In particular, it is possible that, in reservoirs which contain a flowable, dispersed gas phase, the oil bank will never be observed at the producers due to the large amounts of free gas which continue to be produced with the oil. INTRODUCTION One method which has been used to predict the performance of a waterflood is the pilot flood. The pilot waterflood is a flood which involves only a small cluster of the reservoir wells and is located in a small, representative portion of the reservoir. The object is that oil produced from the pilot can, in some way, be related to the oil recovery to be expected from a field-wide expansion of the waterflood. However, these field pilot waterfloods have often been unreliable in the prediction of oil recovery in a fully developed waterflood. This unreliability has also been demonstrated in several laboratory studies of pilot floods. Some of the investigators have shown that there are situations in which the pilot flood oil production is far too optimistic with respect to the oil recovery in the fully de- veloped flood. Others4-G have shown that the pilot results can also be pessimistic, especially if the pilot waterflood is initiated in an oil reservoir which has been depleted by primary recovery and is at very low pressure. The major reason for this unreliability of pilot water-floods is the migration of fluids into or out of the pilot area. By the well-known method of images, if straight lines can be drawn to represent vertical planes of symmetry in a porous medium which contains pressure sources and sinks (injectors and producers), then these lines are invariant streamlines, or lines across which there is no potential gradient, and therefore no flow. In an actual reservoir, these lines of symmetry can never be established exactly because of reservoir inhomogeneities and irregular reservoir boundaries. However, if the reservoir is relatively large and contains wells in repetitive patterns, these lines of symmetry are commonly assumed to exist for the pattern units sufficiently far removed from the reservoir boundary. Lines of symmetry for the five-spot injection pattern are shown in Fig. 1. Each five-spot unit in this figure can be considered confined with respect to flow across its boundary. In pilot floods this is not the case. The lines of symmetry for the pilot patterns investigated in this study are shown in Fig. 2. It is obvious that the fluid within these pilots is not confined and is therefore able to migrate into or out of the pilot area. Intuitively, one can see that, if more wells are added to the pilot, the innermost unit tends to behave more and more like the confined pattern. However, there is a practical limit to the number of wells which should be placed in the pilot. This limit is usually determined by economic factors. It was the purpose of this study to use laboratory fluid-flow models to determine which of the previously mentioned pilot patterns will force the innermost producing well to behave as it would in a fully developed waterflood. Since fluid migration is influenced by initial saturation conditions and the mobility ratio, these factors were included in the study. The ultimate objective of this study was to develop data which would allow the operator to choose a pilot pattern and operating conditions that will yield a production history which can be applied directly as an estimate of the performance of each production well of the fully developed waterflood. BASIS FOR THE STUDY The basic problem of field pilot floods is the migration of the reservoir fluids into or out of the pilot area. This problem has been the subject of previously reported model studies on pilot floods. These studies have been concerned mainly with the development of arbitrary "correction factors" to be applied to the simple, unconfined pilot systems such as the single five-spot. The correction factors were intended to adjust the production history of the un-

By L. F. Mondolfo, W. T. Collins

A study of the relationship between undercooling for nucleation and structure in Sn-Cu alloys with 0.1 to 5 pct Cu has shown that in hypereutectic allojls the halo of tin that surrounds the primary crystals of Cu3Sn5 is larger, the larger the undercooling for nucleation o,f the tin. This increase of halo size results in a decrease of coupled eutectic, and, in alloys far from the eulectic composition, may produce its complete disappeavance, with the formation of a divorced eutectic structure. This was confirnred by the excrrnination of other alloys in which divorced eutectic slructuves are formed, and leads to the conclusion that they ave only an extrenle case of halo forrtzalion , which results when the two phases freeze one at a time and solidification of the first is completed Defove the second starts. It was also found that under proper conditions of nucleation all types of eutectic structures can be formed in the sartte system , and therefore divorced eutectics, like normal and anomalous, are not characteristic of the syslett~, but are mainly controlled by nucleatiorz. Dizlovced eutectics are formed when the phase that tutcleates the eulectic vequires a large undevcooling for ils nucleation and when the cotnpositiorz of the alloy is far from the eutectic., on the side of the primary phase that does not nucleate the other phase. It is recommended that the tevm "divorced" be used in preference to degenerate because it is more desct-iptice of the morphology and mode of forinalion of the structures. ThE variety of structures found in eutectic alloys has been extensively investigated and classified. The most accepted classification is the one by ~cheil,' in which three different types of eutectic were distinguished: 1) normal, 2) anomalous, 3) degenerate (divorced). ATornlal eutectics are typified by the simultaneous growth of the two phases ("coupling") by which the two phases appear as interpenetrating crystals. The presence of a crystallization front, in which the two phases grow side by side, creates the eutectic grains, with the boundaries where the fronts meet. The presence of eutectic grains is the .distinguishing feature of a normal eutectic, according to Scheil. Straumanis and Brakss2 examined the Cd-Zn system and showed that there was a crystallographic relationship between the phases. Later, others4 also investigated additional systems and found definite crystallographic relationships in the coupled eutectics. The anornalous eutectic shows much less coupling than the normal; the two phases are intimately mixed but 'grow without a uniform crystallization front—a consistent crystallographic relationship— and the eutectic grain is conspicuously absent. As in the normal eutectics faster rates of growth result in a finer structure, but there is not the typical uniform spacing of normal eutectics. The degenerate eutectic shows no coupling; in fact the two phases attempt to minimize their area of contact and to form separate crystals. It has been suggested5" that slow cooling may favor this type of structure. Scheil believes that normal eutectics are formed when the two solid phases are present in more or less equal proportions, whereas both anomalous and degenerate eutectics form when one of the phases is present only in small amounts. spengler7 extended much farther this qualitative relationship between the eutectic type and the ratio of the two phases, and added a relationship to the melting point of the constituents. On this basis he proposed two equations for determining into which of Scheil's classifications an alloy belongs. The first equation is: where TI is the melting temperature of the lower-melting component, Tp of the higher-melting component, and Te the eutectic temperature. The second equations is: where is the volume percent of the lower-melting phase and $2 of the higher-melting phase at the eutectic composition. If 0 and/or 4 are in the range 0.1 to 1, a normal eutectic is formed; if in the range 0.01 to 0.1, anomalous; if less than 0.01, degenerate. Although the examples given by Spengler show a good agreement with the formulas, chadwick found that the Zn-Sn eutectic is normal to all growth rates, even though the volume ratio is 12/1, and Davies9 reports that the A1-AlgCo2 eutectic is normal, with a volume ratio of more than 30/1. Many more discrepancies of this type can also be found. Neither Scheil nor most of the other investigators have considered nucleation as a factor in the formation of divorced eutectics. Daviesg states that divorced eutectics form when neither phase acts as

Jan 1, 1965

By H. A. McKinstry, F. F. Lange

A vector analysis of orientating single crystals using the Laue back-reflection X-ray technique is given. Briefly, the analysis involves using a few data taken from a Laue photography and defining the crystal co- ordinate axes in a reference coordinate system. After a few matrix multiplications, the proper goniometer angles can then be determined to orient the crystal coincident with the reference frame. This analysis is easily programed for a digital computer to provide a fast, precise, and efficient method of orienting many crystals which are identical. The general procedure is as follows. The crystal is mounted on a goniometer. Laue photographs are taken until an array of diffraction spots is observed that includes a Laue spot that represents a rotational axis of symmetry. The rotation angles of goniometer are recorded. These angles are defined as positive for a counterclockwise rotation. When the axis of symmetry is located on the Laue photograph, the crystal coordinate axes can be defined in the reference coordinate system* as follows. Two Laue spots are chosen, one of which corresponds to the rotational axis of symmetry and the other to a set of planes whose zone axis is a known crystallographic direction and normal to the rotation axis of symmetry. The Laue spots are used to determine these two crystal directions in the reference coordinate frame. This is done by placing the Laue photograph on a sheet of polar coordinate graph paper and determining the polar coordinates (r, o) of these two diffraction spots in the reference coordinate frame. Their third coordinate is the distance between the crystal and the film (-D). The coordinates Xni of the two crystal directions Nn, (n = 1, 2) in the reference frame are then calculated by the following equations: Xn1 = -D X2n = Ancos on X3n = A, sin on where -tan- 1 rn/D An =Dtan(tan-1rp/D/2) By taking the proper cross products of these two directions (normalized to unit vectors), the crystal coordinate axes 3 (i = 1, 2, 3) can be determined in the reference frame. This is illustrated in Fig. 1. The next step is to determine the relation between

Jan 1, 1969

Geostatistics originated as an application of a classical statistical concept, multivariate linear regression, to the solution of a practical problem, estimation of reserves in the South African gold mines. In this respect, geostatistics should only be considered as one statistical method among many that can be used to evaluate mineral deposits. R.F. Shurtz has studied possible applications of power spectrum analysis to the same problem, and these studies may result in future improvements over the presently accepted geostatistical methodology. The intention of R.F. Shurtz's paper, as stated by the author, is to "relate geostatistical doctrine to classical statistical and mathematical concepts." However, in this comparison the "geostatistical doctrine" appears to include only the simplest among the geostatistical concepts advocated by G. Matheron, while "classical statistical and mathematical concepts" are limited nearly exclusively to power spectrum analysis. The author attempts to compare the two methods, and to prove the theoretical superiority of power spectrum analysis. Unfortunately, a number of errors and incorrect statements are made concerning both the theory and application of geostatistics, which invalidate the comparison and the conclusions drawn from it. The errors made in this comparison are understandable since few scientists can claim to have expertise in two theories as diverse as those compared here. In many respects, this paper is reminiscent of polemics which occurred 15 to 20 years ago when geostatistics and trend surface analysis were compared. Each method has its own merit and limitations, and none can claim absolute superiority. The most misleading statements found in R.F. Shurtz's paper are: The definition of the semivariogram given on page 1923 is incorrect. If the maximum difference between two assays is 1, the maximum value of the semivariogram is not 1, as stated, but 0.5. The comparison of geostatistics and linear regression made in the section entitled "Insufficiency of Classical Statistics?" is not valid. The semivariogram of the sample values given in Table 1 (page 1919) has a parabolic shape indicative of a linear drift. When such a semivariogram is observed, the simplest method of geostatistical estimation (linear kriging with unknown mean) is not applicable. Universal kriging must be used that takes trends into account. On page 1921 it is stated that the use of trends "is officially disparaged in geostatistics." Again on page 1924 mention is made to "Matheron's commitment to random process (intrinsic) models and his present categorical rejection of deterministic (trend) models for mineral deposit evaluation." Indeed, from articles published by geostatisticians in the 1960s one could infer that geostatistical methods are not compatible with the presence of trends. However, even the simplest

Jan 1, 1984

By William Romanoff

As you are no doubt aware, virgin copper, tin and zinc are strategic metals today and little, if any, is available in the manufacture of brass and bronze ingots. The source of alloys used in the manufacture of implements of war are, therefore, from ingots made almost exclusively from the refining of available scrap. It is amusing to hear of the unusual physical properties of various alloys because they mean nothing unless the foundryman is able to produce good sound castings. A discussion therefore means little unless something is said about the relative foundry practice of the various brass and bronze alloys. Among the factors that influence the quality of castings produced are: (I) improper gating, (2) wrong pouring temperatures, (3) poor sand conditions, (4) bad melting practice, (5) faulty pattern equipment, (6) metal. It seems to be the consensus of opinion that about 95 per cent of defective castings can be attributed to the first three causes. Metal while a source of trouble at times, is probably the least responsible for foundry difficulties. As you all know, a molder never makes a bad mold. His first thought is to blame the "damn" metal as this is the path of least resistance. Let's consider the "damn" metal and how it is made. In the manufacture of ingot, scrap is collected at various sources and is shipped to the refiner either directly or through the scrap dealer or broker. It is usually sorted, although not always. In working toward a specified chemical analysis, weighed amounts of various grades of scrap metals are melted, and then oxidized by blowing air through the molten bath to rid the metal of detrimental impurities or reduce them to within specification limits after which they are skimmed off with the aid of some added fluxes. The bath of metal is then poled with wood, chemically tested before and after additions are made to bring it up to required specifications, and finally poured into ingots, after which a final chemical and physical examination is made. As mentioned above, the impurities have either been eliminated or reduced to the point where they meet the specifications of all Government Agencies or Technical Societies. Therefore, why worry as to whether castings are to be made from strategic virgin metals or secondary ingots from available scrap. Tests have continuously been made and it is a proven fact that physical properties are no better from virgin metals than from secondary ingots of the same composition. It is definitely more fool-proof to make castings from secondary ingot than from virgin metals because if an error is made in weighing the copper, tin, lead or zinc of the latter, the analysis is off balance. If an error is made in weighing secondary ingots, you merely have more or less metal but the analysis remains constant. Furthermore, when pure copper is melted. it is susceptible to reducing gases as well as oxides. Secondary ingot is already alloyed with natural deoxidizers such as zinc, etc., and the volatilization of the latter also tends to eliminate reducing gases mechanically.

Jan 1, 1943

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker's problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By A. B. Kinzel

Advance in the art of slag control has been very rapid in the past few years. The viscosimeter method for slag-reaction rate and composition, together with the phosphorus and other methods mentioned by Dr. Herty, allow the steelmaker to rectify and control the slag in the finish period of the heat with much greater precision that ever before. However, the steelmaker's problem is more complex, and in order to make steel of proper analysis in the most economical manner the constitution of the initial slag that has formed immediately after the lime is up in the furnace is of prime importance, as it is one of the factors that determine the carbon content of the charge as melted. Many heats melt with high carbon and some with carbon much lower than is expected so that, on the average, increased furnace time is necessary before reaching the finishing period. The problem, therefore, is to so regulate the slag-making additions that a suitable initial slag will be formed at once. Where all cold metal charges are involved, particularly where the iron and scrap are selected, this may be done with a fair degree of regularity. This regularity results not only in better conditions at the beginning of the heat and during the carbon drop, but also the need for smaller slag-modifying additions toward the end of the heat. The above has been well demonstrated by the work reported by Reagan in the past few years. Where large amounts of cold pig or hot metal are used, the problem becomes more involved. It is much more difficult for the steelmaker to be sure that for any given furnace the heat will form the desired initial slag. Observations of many heats indicate that the pig iron is a dominating factor in the constitution of the slag formed. The scrap is also a factor but in general could be roughly classified and a correction made therefor. The necessity, therefore, arises for a method of correlating the pig-iron charge and type of slag formed for any particular furnace, which resolves itself into a measure of those qualities of the pig iron which affect the slag. The amount of silicon, manganese, phosphorus and sulfur in the pig iron will probably have some effect on the type of slag formed, but

Jan 1, 1935

By Lester C. Uren

With the depletion of our older, and relatively shallow, oilfields and the necessity for securing new production from deeper horizons, much attention is being given to the improvement of oil-well pumps in order that they may function satisfactorily under the more difficult conditions imposed by increased depth. Until recently, practically all of the world's petroleum was secured from wells less than 3000 ft. deep, whereas horizons are now being explored to depths of from 5000 to 7000 ft. in some of the more prolific fields, and it seems probable that the greater part of the future supply must come from depths in excess of 3000 ft. While much of the early production in a new field is obtained by natural-flow methods, when the stimulus of high gas pressure fails, recourse must be had to some method of pumping. The perfection of a pump capable of economically and efficiently lifting oil from depths ranging from 3000 to 7000 ft. is therefore a matter of prime importance to the oil-producing industry. This paper is offered as an estimate of the present state of development of the oil-well plunger pump and as a review of the general principles involved in its operation in deep-well pumping. A design for a new type of oil-well pump embodying several novel features, is also described. Essential Parts of Oil-well Plungeb Pump The pump commonly used in lifting oil from wells in American practice is of the simple displacement type, in which a plunger equipped with a working, or traveling, valoe is given a vertical reciprocating motion in a stationary working barrel. The latter is suspended from the surface by tubing, submerged in the well fluid, and is equipped at its lower end with a stationary standing valve; Figs. 1 and 2 illustrate two common types of oil-well pumps. The simple cup-leather packed plunger of Pig. 1 has its counterpart in the long, hollow, cylindrical, polished steel plunger of Fig. 2; otherwise the two types are identical in the form and arrangement of their essential parts. Fig. 2 shows the additional feature of a "garbutt

Jan 1, 1927

By Don C. Blackmar

THE production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically every type of manufacturing concern. Its business is unique in that it generally buys from its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of many of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the magnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a general way, attempting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturers reclaim their own metallic wastes. MAGNITUDE OF THE MODERN INDUSTRY No particular thought is given to the kitchen accident whereby a ruined saucepan is sorrowfully tossed into the ash can, yet it is a fairly safe guess that within a month this saucepan, together with hundreds of its fellows, will again be in service, perhaps in an automobile crankcase, or in an electric vacuum sweeper. It is by this conversion of the useless into the useful, whether from home or large manufacturer, that the secondary tonnage is built up.

Jan 1, 1928

By Don C. Blackmar

The production of non-ferrous secondary metals has become a large and important industry in the United States, and deals with practically cvery type of manufacturing concern. Its business is unique in that it generally buys frorn its customers as well as sells to them, whether they are individuals, cities, corporations, or the United States government. Its operations are of vital importance to the success and prosperity of nlany of the nation's most important manufacturers; yet there are few industries about which less is generally known by those outside it, whether concerning the rliagnitude of its operations or the details of its actual technique. The industry itself is to blame for this meager publicity, because its technical men have made few attempts to openly exchange ideas, in spite of the excellent examples set by the iron and steel or the copper and brass industries. Whether this is due to the ancient shroud of secrecy generally supposed to cover smelting operations, or because its technical men actually felt that the industry was too puny to be interesting, is hard to say. This paper will consider its subject in a general way, attenlpting to show something of the size and importance of the industry, as well as its fitness to do its work well. Attention will be called to the sound economic reasons for the handling of non-ferrous wastes by specialists, and to the often unseen losses of metals and labor which occur when manufacturc~rs rcclairn thrir own metallic wastes. Magnitude of the Modern Industry No particular thought is given to the kitchen accident whereby a ruined saucepan is sorrowfully tossed into the ash can, yet it is a fairly safe guess that within a month this saucepan, together with hundreds of its follows, will again be in service, perhaps in an autonlobile crankcase, or in an electric vacuum sweeper. It is by this conversion of the useless into the useful, whether from home or large manufacturer, that the secondary tonnage is built up.

By C. Zener

HE present paper has its origin in an attempt A by the author, extending over the last several years, to understand the influence of the magnetic properties of the constituent atoms upon the various properties of metals and alloys. During this study the author has been impressed by the important role which magnetism plays in the many facets of metallurgy. In writing this paper he has attempted to convey to his colleagues some concept as to the role magnetism will play in the future development of metallurgy. In some of the subjects herein discussed, such as the influence of magnetism upon phase boundaries and upon mechanical properties, only general thermodynamical properties associated with ferromagnetism are introduced. For these subjects, it is not anticipated that any serious differences of opinion will be encountered. A discussion of the other subjects requires the adoption of a quite specific model of the magnetic structure of the metal. This model is discussed under "Magnetic Shells and Their Interactions." The simple model adopted in this paper has been criticized' as being mathematically inconsistent. This criticism has been ably silenced by Dr. W. J. Carr' of this laboratory. The simple model adopted in this paper has been criticized as being inconsistent with observations on magnetic structure using neutron diffraction. This apparent discrepancy has been resolved by Bader3 who has shown that the finite velocity of neutrons prevents neutron beams from detecting the anti-ferromagnetic structure of the type predicted by the simple model adopted in this paper. Magnetic Shells and Their Interactions An electronic shell of an atom is specified by two symbols.' The first symbol is a number and denotes the total quantum number of the shell. The second symbol is a letter and denotes the orbital angular momentum of each electron within the shell. The letters s, p, d, f are used to denote an orbital angular momentum of 0, 1, 2, 3, respectively, in units of h/2a, where h is Planck's constant. As we pass from scandium to nickel in the first transition period, we eraduallv fill the 3d shell. This shell is responsible for ferromagnetism and hence may be called the magnetic shell. The component of the orbital angular momentum along some specified direction must be an integral multiple of h/2~. Thus, for a d electron this component can have any one of the values —2, —1, 0, 1, 2 times h/2a. In addition to its orbital angular momentum, each electron has an intrinsic angular momentum, hereafter called spin, due to a rotation about its own axis. This spin can have either of two components + Yz (h/2a) or — Yz (h/2~) along the specified direction. A fundamental principle of atomic structure, known as Pauli's exclusion principle, is that no two electrons in a given shell may have identical components of orbital angular momentum simultaneous with identical components of spin. The 3d shell thus may have at most ten electrons. Since an intrinsic angular momentum of a charged particle is necessarily associated with a magnetic moment, the spin of an electron may be thought of as referring to either this angular momentum or to the associated magnetic moment. The electron configuration of the ground state of the isolated atoms in the first transition row is reproduced in Table I. The superscript represents the number of electrons in each shell. For the purpose of this paper, the most important principle of atomic structure relates to the manner in which electrons are added to a shell as the atomic number is increased. This principle, commonly known as the principle of highest multiplicity or more simply as Hund's rule, states that within a given shell the maximum number of electrons have spins pointing in the same direction as is consistent with Pauli's exclusion principle. An application of this principle to the d shell is illustrated in Fig. 1, where the spin structure is given for shells containing from 1 to 10 electrons. The physical basis of Hund's rule is the exchange energy discussed first by Heisenberg in 1928. This is a coupling between electrons with parallel spins (spins pointing in the same direction), the coupling

Jan 1, 1956

By William L. Grube

PECIMEN preparation for electron metallography involves several steps, such as polishing, etching, replicating, mounting, and shadowing. Although each step must be done with care, the operation requiring the utmost attention is etching. Proper etching is important because the relief pattern developed on the surface of the specimen by the etchant, and reproduced as minute differences in thickness of the replica, determines entirely the amount of detail seen in the final micrograph. The characteristic colored stains, sometimes used in light metallography to simplify identification of certain microconstituents, cannot be tolerated because there is danger of introducing artifacts in the replicating operation. It is also quite difficult to remove plastic replicas from stained specimens. A suitable etchant for electron metallography must, therefore, in all cases exhibit a preferential attack upon each of the microconstituents present sufficient to result in a difference in surface elevation. When only two microconstituents are present, it is not too difficult to find a suitable etchant since their physical or chemical properties are generally sufficiently different to result in a marked difference in attack by the etchant. For example, picral (a saturated solution of picric acid in methanol used as an immersion etch) is a satisfactory etchant for the specimen shown in Fig. 1 consisting of iron carbide particles embedded in a ferrite matrix.'

Jan 1, 1952

By N. S. Stoloff, R. G. Davis

It is concluded from an X-ray stztdy that the formation of the hcp Mg3Cd superlattice is a nuclea-tion and growth reaction. A two-phase, ordered-plus-disordered, region is observed between 153" nnd 141"C. A maximum in the flow stress is observed both at temperature and in quenched specimens within the two-phase region. The peak arises fro112 the extra energy required to create antiphase boundary upon cutting the ordered regions. Hardening during isothermal annealing in Mg3Cd has been shown to be similar to the domain hardening in Cu3Au-type alloys in that up to the maximum the structure is ordered domains growing into a short range ordered matrix. The hardening is due to a combination of short range order strengthening and the strengthening produced when antiphase boundary has to be created. In a recent study1 of the effect of long-range order upon the mechanical properties and deformation modes of hcp Mg3Cd a comparison was made be- tween quenched (disordered) and slow-cooled (fully ordered) specimens. The most striking observations were that the disordered alloy yields at a much higher stress than the ordered alloy, and that there is a change in slip mode from primarily (_0001) ba_sal slip in the disordered state to (0001), {1010}, {1122}, and {l011} slip in the ordered state. The main purpose of the present work is to extend these observations to determine whether MgsCd exhibits a peak in flow stress at an intermediate degree of order, or at a critical domain size, as do other orderedstems. However, disagreement exists about the Mg3Cd order transformation with respect to: 1) the location of the critical temperature for order, 165°C or 153"~,' and 2) how the degree of order varies with temperature. Welber et a1.5 concluded from specific heat measurements that the formation of Mg3Cd is a second-order reaction with the degree of order a continuous function of temperature, while Moore and Raynor concluded that it is neither a first-order reaction, with the degree of order a discontinuous function of temperature, nor a second-order reaction. Consequently it was considered necessary to undertake an X-ray investigation into the change in degree of order and structure in the

Jan 1, 1964

By H. D. Hoskold

This instrument, shown in Fig. 1, is not generally known, though it has been used in England, and found very practical, handy and useful in work not requiring a transit or theodolite. It is not only a good miner's dial, but a circumferentor as well; that is, it can measure horizontal angles like a theodolite. The magnetic bearings are conveniently read on the inward-beveled upper divided circle; while another circle, graduated on the base-plate, is used for reading the horizontal angles with a vernier. Two leveling spirit-bubbles are sunk in the same base-plate. The vertical divided semicircle is attached to the compact-box by two short axes, which permit the semicircle, with its plain sights, to be turned down to a horizontal position, and rest upon a pin, which relieves the axes from strain. This adjustment gives a clear view of the needle and vernier, and protects the instrument from injury, when carried through low mine-workings. A groove in the semicircle receives a sliding-bridge which carries the plain sights, and a vernier for reading vertical angles. A ball-and-socket-headed tripod is used; but sometimes the instrument is mounted on parallel-plates and level-ing-screws; and sometimes a telescope is attached, instead of the plain sights. The instrument is admirable for all such Mexican surveys as Mr. E. A. H. Tays describes ;l and saves so much time and labor as to be vastly superior to the less accurate hanging-compass called by him a " bully " instrument. If the hanging-compass was ever used in England, it has long since given way to more modern and superior instruments.

Jan 1, 1905

By Howard S. Lee

In central Colorado is a great belt of intrusive porphyry nearly 100 miles long (160 km.), extending from the Clear Creek district on the north to Aspen on the south, which includes many of the well known mining camps of the state. Near the southern end of this belt, at Leadville, the occurrence of these intrusives is most marked, resulting in intensive mineralization and the formation of a great variety of large orebodies. During the past 40 years, Leadville has been a steady producer of gold, silver, lead, zinc, manganese, iron, and bismuth, in the forms of sulfide, carbonate and oxide ores. It is the purpose of this paper to discuss pyrite alone, which, under present economic conditions, is valuable chiefly for its sulfur contents. The ore-bearing formation of the Leadville district consists of two beds of limestone separated by a layer of quartzite. The upper limeatone is carbonaceous, and is known locally as the blue limestone. It varies in thickness from 50 to 300 ft. (15 to 91 m.). The lower limestone is Silurian, known locally as white limestone, and is about the same thickness as the upper bed. Underneath the Silurian limestone is a layer of Cambrian quartzite from 100 to 250 ft. (30 to 76 m.) thick resting on Archean granite, which forms the limit of ore deposition. As a rule, there is a sheet of white porphyry above the upper, or blue limestone; a sheet of gray porphyry is associated with the blue limestone, either in or below it, but the porphyries are not so regular as the quartzites and limestones and are not always found in their expected positions. Throughout the district there is an elaborate system of faults and intrusive porphyry dikes, which have an important bearing on ore deposits. The writer has seen two or three orebodies which were not closely associated with either a fault or a porphyry dike, but if the minor fractures and water courses are considered as part of the fault system it is safe to say that all orebodies are directly traceable to one or both of these causes. The distribution of pyrite in the Leadville district is quite general; but, eliminating the smaller bodies and those containing prohibitive quantities of zinc or lead, and considering only the larger deposits commercially valuable for their sulfur, we find the chief pyritic ore-bodies extending in a zone approximately 6000 ft. (1828 m.) long and several hundred feet wide, from the Yak and Moyer, on the south; through the Louisville, Greenback, Mahala, Adams, and Wolftone, on Carbonate Hill; across Yankee Hill, and into the Quadrilateral, Denver City, and Tip Top, on Fryer Hill.

Jan 1, 1920

By Donald W. Scott

GENERALLY speaking, there is nothing very difficult about taking good micrographs of photogenic thin sections or grains with a petrographic micro-scopecamera setup. However, sometimes it is desired to show some detail that cannot be illustrated satisfactorily by the usual micrographs taken with parallel polarized light, with crossed nicols, or even with two micrographs. A simple procedure giving good results has been used at Battelle Memorial Institute for subjects falling into this classification, and it is believed to be of interest, especially to research people who must sell a point to executives through the medium of well-illustrated reports. The following problem illustrates a typical application: It is desired to photograph a thin section of an iron ore to illustrate the character and association of the iron oxides and the individual quartz crystals. A magnification of 75 dia. is acceptable. A micrograph of the field in question (Fig. I[a]) was taken with parallel polarized light. Due precaution was taken to provide critical illumination, correct exposure, a sharp focus, a good darkroom technique, and other essential conditions. It illustrates correctly the iron oxides, but it fails to show the individual quartz crystals. A micrograph of the identical field (Fig. I[b]) was taken under the same precise conditions, but with crossed nicols. It gives a better idea of the character of the individual quartz crystals but is likely to be misinterpreted unless accompanied by a lengthy descriptive note. This micrograph suggests that the centrally located, large black area is composed entirely of iron oxides. That this is an incorrect interpretation is evident by reexamining the micrograph of Fig. I[a]. The correct interpretation is that the dark area contains quartz crystals oriented with their optical directions parallel to, or nearly parallel to, the vibration directions of the polarizer and analyzer of the microscope. Thus, the executive, or anyone who had not done the work personally, would get no more than a fair interpretation, even if two micrographs were included; and in the interests of both brevity and clarity, one micrograph usually is more desirable. Exactly how many quartz crystals occur in this region cannot be told from the two micrographs, and a printing of the two negatives in register would likewise not show the detail desired. Thus, it is evident that some subjects cannot be satisfactorily illustrated by the usual procedures. In photographing Fig. is the light was subdued and, during the entire exposure of 75 sec., the analyzer nicol was rotated uniformly in its mounting from a crossed position to 45° uncrossed position to introduce the desired amount of contrast in the various individual quartz crystals. The true reproduction of the character and association of the iron oxides, and the additional structure and detail in the quartz areas, is apparent. It might be

Jan 1, 1946