Search Documents

W. VAN DER GRACHT, Tulsa, Okla. (written discussion.*).-I fully agree with Mr. Daly's observation that there is such a coincidence between petroleum deposits and geosynclines as to suggest them to be "closely allied phenomena." However, I accept no "identity of cause." To me the explanation is a simple one. Geosynclinal deposition is the first phase in the formation of a mountain, chain, and petroliferous deposits are indeed closely allied to zones of, mountain folding. In fact, petroleum is a typical occurrence in those beds, which represent the flysch facies, to use the Swiss expression. The uplifting of a great mountain chain is a very slow process; it gradually sets ill as a slow geo-anticlinal upheaval within a zone off former geo-

Jan 1, 1918

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.1 Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques.

Jan 12, 1957

By A. Berghezan, E. Bull Simonsen

A simple and general method is described for melting and zone refining refractory metals by induction heating on a specially shaped water-cooled copper crucible. The crucible is the essential part of the apparatus and is placed horizontally. It consists of either a copper plate, or a flattened tube, or of several parallel small diameter tubes all water cooled. The charge lies on the crucible, or whenever possible, is suspended above it. This assembly goes into a transparent quartz tube and the whole is passed through the coil of a radio frequency generator. Vaarious atmospheres can be used. No contamination is detected from the copper crucible. purification is obtained both by selective evaporation of impurities and by zone refining. METHODS of melting and refining relatively large ingots of all reactive and refractory metals as well as some semiconductor materials have been developed in this laboratory during the past several years using induction heating and cold crucibles. These methods are simple and permit the use of a variety of starting materials in preparing ingots of suitable shapes. Among these methods, two are of particular interest. One deals only with the problem of melting without contamination. In this method the induction coil has a specially designed shape and acts simultaneously as heating element and crucible. The second goes one step further, being designed for both melting and further purification of the refractory metals. The aim of this paper is to describe the second method which is of more general interest and of greater applicability to metallurgical problems. A) THE PRINCIPLE OF THE MELTING AND PURIFICATION METHOD As originally proposed by one of us1 the method consists of heating a charge of any refractory metal or semiconductor material to the melting point on a water-cooled copper crucible by passing both the charge and the crucible through the induction coil of a radiofrequency generator. Although both are subjected to the same induction field, one achieves the melting of a refractory metal on a copper crucible even when the refractory metal has a melting point of more than 2000°C above that of the crucible. This seemingly "odd" method works effectively for the following reasons. Because of its high electrical and thermal conductivity as compared with the material being melted, copper can be used as the crucible and kept at a low temperature while the material is heated by induction to its melting point. With water Silver and other highly conducting materials can also be used. If a nonconducting material is contemplated, e.g. SiO or a high polymer, a very thin wall should provide efficient cooling. cooling through ducts in the crucible its temperature can be kept between 40" to 70°C; thus its electrical resistivity is kept low, while the resistivity of the charge increases rapidly as its temperature is increased. B) APPARATUS The crucible is the essential part of the apparatus. It has been designed in various shapes depending on the atmosphere used, whether vacuum or an inert gas or hydrogen. In all crucible designs an effort was made to reduce its volume to "nothing but the cooling water" in order to avoid shielding the ingot from the induction field. In practice it is either a

Jan 1, 1962

The New York Meeting this year will-be held from Monday, February 19 to Thursday, February 22. The Committee on Arrangements, the personnel of which is given elsewhere in this Bulletin, is making plans to duplicate the conspicuous success of last year's meeting in New York. The papers to be read at this meeting, it is believed, furnish material for interesting and profitable technical sessions and symposiums. The social features are being carefully planned since it is believed that these form an important part of such meetings; several functions are to be, given with the object of fostering the get-together, know-each-other-better spirit. Ladies are invited to attend this meeting and participate in the various affairs planned by the Ladies' Committee and by the Committee on Arrangements. This preliminary notice is given in order that members may make their plans now to be in Now York at the time of the meeting. Full details will be sent to the membership through the mails as soon as the program has been definitely fixed.

Jan 1, 1917

By Carl Floe

A NUMBER of proposals have been made for the hydrometallurgical recovery of copper from flotation concentrates, but as yet no process has been developed that has demonstrated an ability to compete with the present smelting methods under ordinary conditions. The treat-ment of copper concentrates by hydrometallurgical methods is in general similar to that used in the present electrolytic zinc process and involves roasting, leaching with H2S04 solution, separation of solutions, control of impurities and electrodeposition. While many of these steps are simpler and more readily carried out for copper than for zinc, a number of inherent difficulties have prevented the general adoption of the process. To compete with smelting, the following problems must still be con-fronted, although many solutions for their have been proposed: (1) con-duction of the roast in such a way that leaching will give an extraction of copper comparable to that obtained by smelting; (2) regulation of the ferric iron content of the solutions during electrolysis; (3) disposal of the excess acid regenerated from the sulphates formed in roasting; (4) eco-nomical recovery of the precious metals from the leach residues. The roasting problem is largely one of preventing the formation of copper ferrites, CuO.Fe2O, and Cu20.Fe2O3, which are quite insoluble in dilute sulphuric acid. These ferrites are apparently formed' to a small extent even at low temperatures and above 650° C. their formation is rapid1. While it is possible to carry out laboratory roasts in such a way that less than 5 per cent of the total copper is present in the insoluble ferrite form, a closer temperature control is required than can readily be obtained in industrial furnaces. The flash" roasting effects and consequent high temperatures that occur as the calcine falls from hearth to hearth in the ordinary multiple-hearth roaster are probably largely responsible for the inevitable formation of some ferrites. The result is that in a commercial plant the extraction of copper would not average more than 90 per cent in a single 10 per cent H2SO4 leach. This is

Jan 1, 1937

By J. J. Gilman

THEORIES of fracture in metals have been based primarily on the dependence of fracture strength on grain size. This dependence was first observed by Masing and Polanyi.l These workers, as well as 0rowan12 and Davidenkov and Wittman,' thought the grain size could be equated with the crack size in the Griffith condition for crack propagation.4 In this way they could account for the observed proportionality between fracture stress and the reciprocal square root of the grain size. The chief results of recent investigations of the fracture strength of polycrystals are summarized in Fig. 1. Low for iron,5 Petch for iron,' Greenwood and Quarrel for zinc, Petch and Zein for zinc,' and Hauser, Landon, and Dorn for magnesium'' have all found that the fracture stress of a polycrystal is proportional to the reciprocal square root of the grain size. Also, they find that, for large grain sizes, the fracture stress lies near the extrapolation of the yield-stress curve determined at small grain sizes; where measurable plastic strain precedes fracture. Low9 has gone a step further and shown that, in Range 1, the fracture stress in tension is almost identical to the yield stress in compression for a given grain size. Homes and Gouzou, 10 and Low also have shown that, in Range 2 of Fig. 1, microcracks form when the yield stress is reached, but they do not cause failure until the stress reaches a much higher value. The fact that yielding always precedes fracture suggests that fracture is induced by plastic flow. A mechanism by which this might occur was first proposed by Zener.11 He pointed out that blocked dislocations would cause stress concentrations which might cause fracture. The blocking would be caused by grain boundaries. This idea has been developed by Eshelby, Frank, and Nabarro,12 by Koehler,13 and by Stroh.14 By means of etchpits blocked dislocations have been observed in brass by Jacquet,15 in zinc by Gilman,16 and in lithium fluoride by Gilman and johnston. The blocked-dislocation theory and the experiments that bear on it have been summarized by Mott.18 One of the strong points of the blocked-dislocation theory is that it can explain the grain-size dependence of the fracture stress in a natural way. However, Low9 has pointed out that the theory is not satisfying when it is considered quantitatively. Gilman10 also has criticized the theory and presented an alternative interpretation of the relation between fracture stress and grain size. Since the blocked-dislocation theory is not the only theory that can explain in the grain-size effect, it is necessary to find other evidence either to support or deny it. In this investigation the following points were studied: 1) If blocked dislocations normally cause fracture, then the fracture stress ought to be very high in the absence of plastic glide. Is it? 2) If dislocations must be blocked in order for metals to fracture, then certain types of grain

Jan 1, 1959

INTRODUCTION The meaning of cash flow has already been defined as after-tax earnings available for use by the corporation or business. It is therefore apparent that a significant part of mineral economic evaluation is concerned with correct and accurate computation of taxable income under existing tax laws, and the proper treatment of tax allowances and deductions. The various methods of depreciation, depletion, and amortization are all means whereby the investor can earn back or recover, before taxes are imposed, the investments made for purposes of doing business or for the production of income. Each of these three types of tax deduction are applied to different investment items such as property, equipment, buildings, research, etc. The cost of buildings, equipment, machinery, and transportation equipment are representative of capitalized business costs that must be recovered by depreciation over the life of the asset. The property investment costs of acquiring natural resources such as minerals, oil and gas, and standing timber are examples of investment costs that may be recovered by depletion. Several other capitalized business costs, such as research expenses and trademark expenses, may be recovered by amortization. The term "capitalized" means that the in- vestment cost is not deducted as an operating expense in the year that it is incurred, but is spread out over a period of years through depreciation, depletion, or amortization deductions according to lawful schedules. Of course, any capitalized cost can only be deducted once. The other costs of doing business which are not capitalized, such as labor and operating costs, are said to be "expensed," i.e., they are written off for tax purposes in the year they occur. DEPRECIATION Depreciation, according to US tax law, is a deduction from taxable income permitted as a "reasonable allowance for the exhaustion, wear and tear of property out of its use or employment in a business." The original cost of the property is the usual basis for determining depreciation. Since depreciation write-off is applied over the useful life of the asset, the first step is to determine the estimated useful life or its allowable depreciable life. These two lives may or may not be the same. No average life is applicable to all types of depreciable assets under different conditions or in different types of business. It is the taxpayer's responsibility to determine the useful life of the asset according to his own operating conditions and experience, within the guidelines set by the US Internal Revenue Service (IRS). The Class Life Depreciation Range (ADR) System permits the taxpayer to choose from a range of depreciable lives at 20% below or above the present guideline life. The second step required in calculating depreciation is to determine an estimated salvage value for the asset. The salvage value is an estimate, made at the time of acquisition, of the amount of money which can be realized by the sale of the asset at the end of its useful life. The four depreciation methods most widely used in the US are: (1) the straight-line method, (2) the declining balance method (double declining balance), (3) sum of the years - digits method, and (4) units of production method. Straight-Line Depreciation Method The straight-line depreciation method is the simplest for calculating depreciation. The depreciation for each year is determined by subtracting the estimated salvage value from the first cost of the asset and dividing the result by the years of life. The method gives equal annual deduction over the depreciable life. Salvage value equal to or less than 10% of the first cost may be ignored. [first cost - salvage Straight line = years of life ] Declining Balance Depreciation Method Declining balance depreciation, or double declining balance (DDB) as most frequently applied, is used for accelerating depreciation in the early years of the asset and is the fastest depreciation method allowed by the US Internal Revenue Service. The declining balance

Jan 1, 1980

By Henry Howe

THAT the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First; each particle of any composite liquid, whether it be an aqueous solution or a molten metal; in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the, existing temperature, - and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already, solidified; A, Fig. 1. The other part is, fusible at the existing temperature and hence remains molten. In the case of carbon Open steel, the part. of each drop which actually j; Sea solidifies is poorer, in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying,. half-drop enriches . the other, half-drop in carbon, and Layer of Liquid thus. makes it unfreezable at the existing tem- Fig. 1.MECHANISM OF perature. SOLIDIFICATION. By this- mechanism there arises during solidification a " littoral" or shore layer- of liquid, B, Fig. 1, bathing the already solidified. walls, and more fusible than either those walls or the great remaining central mass of liquid or "deep sea," C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile. heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal

Jan 2, 1919

By A. F. Frederickson

Rapid advances in any branch of science often follow the development of new instruments or techniques which permit the scientist a closer look at the material in which he is interested. With the development of the polariz¬ing microscope, modern petrology was born. The resolving power of the microscope, however, was not great enough to enable the geologist to dis¬tinguish or identify the material now known to be minerals which constitute the bulk of the rocks known as "clays" and laterites. The discovery of X-rays and the development of powder X-ray diffrac¬tion techniques provided the extra resolving power necessary to get "a closer look" at the minerals in the clays and laterites. These techniques are largely responsible for the great strides made in the past two decades in the identification of the clay, sesquioxide and hydroxide minerals. To obtain an X-ray diffraction. pattern of a mineral or rock is relatively a simple procedure, but to interpret this pattern in terms of crystal structure or min¬eral identity is quite another matter. It has taken the combined talents of physicists, physical and colloid chemists, mineralogists, and geologists to unravel the identity of some of the minerals in these complex rocks and, as this symposium will indicate, many more problems remain to be solved. To assist in the identification of these minerals, we have the ever-useful microscope, which, is supplemented by the development, only in the last ten years, of differential thermal techniques and the powerful and costly "eye" that enables us to see the shapes and sizes of extremely small particles -the electron microscope. To this array of equipment must be added such gadgets as supercentrifuges, spectrographs, and the apparatus necessary for chemical analytical work. Obviously, not only is it difficult for any one man to master all of the techniques to the point where he can do competent re¬search, but also few institutions are able to provide the high capital outlay for purchase and maintenance of suitable equipment. Here we clearly see that if this equipment is to help us solve our many problems, a close co¬operation of specialists from various institutions and industry is essential. This, however, is less than half the problem. If the geologist is going to learn to intelligently find, and the industrialist to intelligently and eco¬nomically exploit the materials that constitute a large part of the mineral wealth upon which our way of life is based, we must get a better insight into

Jan 1, 1952

By I. N. Knap

Discussion of the paper of HOWARD R. HUGHES, presented at the Now York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 629 to 635. I. N. KNAPP, Ardmore, Pa.-The claims made in the paper for the Sharp & Hughes cone bit are modest. I have used it with satisfactory results. It is a wonder for eating through hard, brittle rock; it will drill through iron pyrites that the fish-tail bit cannot enter. Soft ground is apt to contain concretions that are much harder than the containing ground. ?We have at times in drilling with a fish-tail bit thought the hole was partly in such hard material and partly in soft, thus making a difficult place to drill past in the ordinary way. By changing to a Sharp & Hughes cone bit such obstructions were easily overcome. This cone bit has greatly widened the range of work that may now be profitably accomplished by the hydraulic rotary method of drilling. It is not, however, adapted to drill soft or sticky ground, the old fish-tail bit being better for such purposes. The fish-tail bit usually scrapes its way through the material drilled, but not always. I believe at times it cuts and chips in soft friable rock. That is, the bit seems to bite into the rock, and when sufficient torsion is put on the drill stem it breaks its hold and jumps around and chips the rock from the bottom of the hole, like a stone cutter's chisel, and then takes another hold. This condition occurs only in friable material when the bit is sharp and the feed properly controlled. The Sharp & Hughes cone bit is a most valuable -tool for the rotary driller.

Jan 5, 1915

By Haydn H. Murray

The term clay is somewhat ambiguous unless specifically defined because it is used both as a rock term and as a particle size term. Actually most persons using the term clay realize that it has a double meaning and in most instances define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it so that the definition has to be general. Clay is a natural, earthy, fine-grained material composed largely of a limited group of crystalline minerals known as the clay minerals. Many definitions state that a clay has the property of plasticity when wet, but some clays are not plastic, i.e., halloysite and flint clay; however, most clay materials are plastic when wet. As a particle size term, clay is used for the category that includes the smallest particles. The maximum size particles in the clay size grade are defined differently on some grade scales. Soil investigators and mineralogists generally use 2 microns as the maximum size. The Wentworth scale' defines clay as material finer than approximately 4 microns. Grim' has found it convenient to use the term clay material for any fine-grained, natural, earthy, argillaceous material and in this way can include clays, shales, or argillites, and some soils if they are argillaceous. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, still the term is generally understood by all who use it. Clay is an abundant natural raw material and has an amazing variety of uses and properties which will be discussed in this chapter. In order to understand better the relationships between the clays and their uses, a brief discussion of the structure, chemical composition, and identification of the clay minerals is given. Mineralogical Composition of Clays Clays are composed of certain groups of hydrous aluminum, magnesium, and iron silicates that may contain calcium, potassium, and other ions, which are called the clay minerals, and other minerals of variable composition, which are nonclay minerals. Both clay minerals and nonclay minerals influence the properties of a clay material. In order to understand the relationship between clay minerals and the properties of a clay material, a short summary of the structure and composition of clay minerals is necessary. Any scheme of classification tends to impose a certain rigidity and as new and additional data become available it is necessary to revise classifications. Brindley3 has discussed the classification and structural mineralogy of clays in very lucid fashion and chose a classification based on structural features and chemical composition. Grim2 proposed a tentative classification which is based on the structural attributes of the various clay minerals. This classification is relatively simple and workable, and is shown as follows: I. Amorphous Allophane group II. Crystalline A. Two-layer types (sheet structures composed of units of one layer of silica tetrahedrons and one layer of alumina octahedrons). 1. Equidimensional Kaolin group kaolinite, dickite, nacrite 2. Elongate Halloysite group

Jan 1, 1960

By G. H. Wilson

INTRODUCED in 1946 to serve a need in power- plant operation, closed-circuit TV has been used by well over 200 organizations in approximately 25 different industries. Known as industrial television, or simply ITV, it can be described as a private system wherein the television signal is restricted in distribution, usually by confinement within co-axial cable that directly connects the TV camera to one or several monitors, Figs. 1, 2. The picture is continuous and transmission is instantaneous, permit- ting an observer to see an operation that may be too distant, too inaccessible, or too dangerous to be viewed directly. Destructive testing or the machining of high explosives can now be conducted hundreds of feet away by personnel who still have close control through the eyes of the TV camera. It is also possible for one man to control operations formerly requiring the co-ordinated efforts of several workers. For example, at a large midwestern cement plant conveyance of limestone from primary crusher to raw mill and loading into five storage bins once necessitated the work of two men, one having little to do but prevent spilling of material by manually moving the tripper on the belt conveyor as occasion required. TV cameras mounted on the tripper now provide bin level indication to the conveyor operator at the crusher position so he is able to control the entire loading operation remotely, Fig. 3. By means of a switch, the picture from either camera is alternately available on a single viewer, or monitor, Fig. 4. Each camera is mounted on the tripper by means of a simple adjustable support and looks down into the bin, which is identified by the number of cross members on the vertical rod. Each associated power unit is located on a platform above the camera, Fig. 5. This centralized control by means of TV often has produced superior results, and in many instancés saving in operating costs has been sufficient to write off equipment costs within six months to a year.

Jan 7, 1954

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

By L. E. Shiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning —10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed. IN cleaning coal it has long been recognized that methods which give excellent results for the coarser sizes may give poor or even no cleaning for the finer sizes. Effective cleaning of the fines, therefore, is usually a separate and distinct problem. For many years the problem of fines was considered of relatively minor importance. Now there is growing interest in methods of cleaning the fine sizes of coal because: 1. There are more fines. Increasing mechanization and the adoption of full seam mining methods have resulted in the production of a greater percentage of smaller particles than were produced by hand loading methods. 2. The fines have deteriorated in quality. The same causes that have led to increased quantity have also operated to decrease quality through greater contamination with slate, rock, and other diluents. 3. The fines have become more valuable. When coal was comparatively cheap, loss of the finer sizes was tolerated but, with the rapid increase in the cost of mining coal, it has become imperative that the maximum amount of clean coal be recovered from the mixture of coal and rock delivered to the tipple. 4. In many cases, the fines have become a stream pollution problem. Increasing governmental activity and legislation to prevent stream pollution often have made it necessary to retain the fine material which formerly was permitted to escape with the washer effluent into flowing streams. The Sloss-Sheffield Steel and Iron Co. operates four coal mines, all within a 20-mile radius of Birmingham, Ala., with a total annual production of 1,-250,000 tons of washed coal. Three of these mines are in the Mary Lee seam and one in the Jefferson seam. Although some steam and domestic coals are produced, the major portion of the coal is used to make coke for blast furnace operation. Fine coal is desirable for coking, and all the coal so used by Sloss is crushed to 1/4 in. Therefore, there is no problem of an outlet for even the finest sizes of coal. Since the coal is used for metallurgical purposes, low ash is of greater importance than would be the case if it were used for steam generation or domestic heating. Based on present blast furnace practice at Sloss, it is calculated that each percentage of ash in the coal carries a penalty of $0.22 per ton of coal. Thus there is a considerable margin for operating costs in a fine coal cleaning method that will result in materially lowering the ash content of the cleaned coal. Development of Fine Coal Cleaning Problem In 1942 Sloss reopened its Bessie mine and constructed at this location a new preparation plant to clean 11/4 in. x 0 coal from the Mary Lee seam.

Jan 1, 1951

By John R. Dyni

Colorado nahcolite deposits, estimated at 29 Gt, formed in an asymmetric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCO3) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62%), disseminated crystals (24%), and impure beds (13%). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening. Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a Possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1982

By R. V. Ramani, George W. Luxbacher

Computer simulation of mine ventilation systems, after a slow start in the early sixties, is gaining increasing acceptance for planning, design, and evaluation purposes. Numerous programs are readily available from government, university, consulting, and industry sources. The computer adage "garbage in, garbage out" is as applicable in ventilation engineering as in any other application of computers, and has been responsible for the questionable results obtained in some instances. The source of input data for a ventilation simulation is most often a pressure-quantity survey of the mine, or, in the case of a new mine, information derived from a survey of an existing mine which has conditions similar to those expected in the new mine. The crucial step is to generate simulation input data from the ventilation survey. Problems such as quantities that do not balance, pressure gradients opposite to measured air flow, differences in the pressure datum in a multi-shaft mine, modeling of leakage, and deviations in flow from the square law (H=RQ2) are frequently encountered and must be resolved. The purpose of this paper is to discuss these aspects and to propose procedures which can lead to input data for valid simulations of mine ventilation systems.

Jan 1, 1982

GROWTH of the United States to industrial supremacy in the world is mainly because of the rapid exploitation of natural resources. The easily found high grade mineral resources have been depleted and attention has turned to low-grade ores. Progress has been made from the comparatively crude mining and milling techniques, which sufficed for the rich deposits, to more complex technology for exploiting low-grade ores. In spite of this progress the defense program is pointing up the fact that the mining industry is caught short on ability to produce the needed mineral raw materials. The mining industry is digging itself out of business here in the United States.

Jan 5, 1951

By T. M. Gurr

The United States is the world's leading producer of phosphate rock. In 1975 according to the US Bureau of Mines' statistics, 44.3 million tonnes (48.8 million st) of phosphate rock were produced in the United States, 1 which is 40.6% of the world's production.2 The major phosphate producing areas of the United States are located in Fig. 1 and the production for 1975 is listed as follows:

Jan 6, 1979

By R. P. McLaughlin

EXACT information as to performance of the gas lift from the mechanical engineering standpoint is hard to obtain. Several hundred wells are now producing in California fields by means of the gas lift, and a survey of results shows that the gas lift has increased production at these wells by approximately 60 percent. Similar or even larger figures describe results in Mid-Continent fields. Such an increase in output of oil is so satisfactory, to the average oil producer, that it may not encourage investigation looking to more efficient operation. The cost of lifting oil by compressed gas varies from 3 c. to 15 c. per bbl. of oil, depending upon the efficiency of the gas lift. A difference of 10 c. or 12 c. per bbl. of oil is immediately noticed by an oil operator and the cost in production is as real to him as is the price of his product. Therefore, the efficiency of gas-lift process deserves more consideration than it has been given in some quarters. It has been found that there is a wide variation between different operators and at different wells in the amount of gas used per barrel of oil lifted. Some of the most efficient operations show oil being lifted with only slightly over 400 cu. ft. of gas per bbl. of oil.1 On the other hand, wells are being flowed and using as high as 3000 cu. ft. per bbl. of oil. The cost of compressing gas to 300 or 400 lb. varies from 3 c. to 5 c. per 1000 cu. ft. of free gas. This figure has been obtained from a number of sources and as a matter of fact is the basis of actual business transactions involving gas compression. The cost of lifting oil with compressed gas is thus determined.

Jan 12, 1926

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.' The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.' The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968