Search Documents

By Charles E. Wait

IN order to secure cupels uniform in size, density, etc., I have arranged a machine which has proved quite satisfactory, and is so simple and inexpensive as to be within the reach of nearly everyone. It has been in operation here about four years, and with it all cupels used in the assay department of the School of Mines have been made. As shown in the accompanying figure, it consists of a common letter-press, the movable platen of which has been removed. In place of the plate, there is attached to the screw a plunger, which turns with the screw, moving up and down, and making the depression in the cupel. The ring holding the bone-ash is held in place directly underneath the plunger by a wooden guide fastened to the base of the press. There is also fastened to the top of the guide for the ring, at a distance above the base of the press equal to the height of the cupel-ring, a piece of mood about § inch thick, under which the ring will just slide into place, and through which there is cut a circular hole exactly fitting the plunger, guiding it in its downward movement always in the same vertical line; this last guide not only directs the plunger, but also prevents the lifting of the ring by the plunger, upon the raising of the latter.

Jan 1, 1886

By William Reynolds

THIS paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. FACE PREPARATION When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of complete-ness to which these impurities are removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miner is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation.

Jan 1, 1936

By Charles H. MacDowell

Up to 1909 the American public had little knowledge of, or interest in, potash. Some remembered that it had to do with soft soap and sore throat,, but further they knew not. In 1909-10, the German-American potash war, and the publicity attending hostilities, brought home to America the knowledge that potash was an important article of commerce; that Germany monopolized its production and distribution, and exercised all the prerogatives attending complete control. The present war, with its transportation embargo, has again directed attention to Germany's strength as a potash producer and her present unfortunate situation as a distributor. As a consequence, the search for potash takes on new life and it again becomes a subject of general interest. My first knowledge of potash came from a study of the German potash exhibit at the World's Fair in 1893. This investigation led to the recommendation that Armour & Co. engage in the manufacture of commercial fertilizers and the fertilizer branch was organized early in 1894. From then to now " potash " has been a live subject. Two and eight-tenths per cent. of the earth's crust consists of potassium oxide. It is an important constituent of feldspar, granite, and other igneous rocks. Potash is valuable commercially in a water-soluble form. In igneous rocks it is locked in so tight that it is of little value and no utilization in a commercial way has been made of these insoluble forms. Potash in water-soluble form is found in large deposits in Germany; in smaller deposits in Austria and Spain; and in brines in some of our Western arid basins. The deposits in Germany, Austria, and Spain are concentrations from sea waters containing potash derived from the decomposition of potash-bearing rocks. It has been found that the amount of potash remaining in decomposed rocks is not the same as that in the original rock. For instance, granite containing originally 5.58 per cent. potash contained only 1.49 per cent, in the decomposed rock. Syenite containing 6 per cent. in the original

Jan 1, 1915

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By William Lodding

In leaching ores at atmospheric pressure it is often desirable to apply high reagent concentration, long exposure time, and elevated temperature. All of these conditions tend to increase the treatment cost. In conventional leaching, direct or countercurrent, the leaching fluid is needed to transport the solids through the process. This requires relatively large volumes of fluid and limits the reagent concentration economically feasible. The relatively high dilution also increases fuel cost if leaching is to be done above ambient temperature. Heating of water is expensive.

Jan 3, 1967

By Gerald, Sherman

INCREASED production and con¬sumption of all metals, indicate the progress of industry toward that condition formerly thought to be normal. With no market limitations on silver and gold the two new precious-metal mines, the Silver Queen (now the Golden Queen), in southern California, and the Sunshine, at Kellogg in northern Idaho have made progress toward a high routine production. The Golden Queen 300-ton mill is finished and ready. The Sunshine mill has been enlarged and production is now at the rate of 500 tons per day of high-grade silver ore. The Hecla Mining Co. is developing the Polaris vein, which should be the extension of the Sunshine to the east. Some rich ore is reported. The developments of the' East African Gold Fields, Ltd., in the Lupa gold field of Tanganyika Territory, have made good progress, but operation in an isolated locality is not rapid and a large plant will be required. There have been no other discoveries reported that can be compared with the three mentioned, but production has increased, with greater capacity in dredging equipment and underground mines more adequately prepared for production.

Jan 1, 1936

By J. G. Kura, P. D. Frost, L. W. Eastwood

THE preparation and general properties of mag-nesium-lithium base alloys have been described in earlier papers.l,2 Lithium forms solid solutions with pure magnesium, lowers its density, and improves its formability. The improved isotropy and better formability of these alloys are attributed to the ability of lithium to convert the magnesium lattice from hexagonal (alpha phase) to body-centered-cubic (beta phase) structure. This change in structure is, however, accompanied by some limitations which make it difficult, if not impossible, to combine all the desirable properties in one composition. The most important of these limitations is the tendency of the high-strength alloys to overage and lose strength at temperatures of the order of 150" to 200°F. A study was made of the effects of composition and heat treatment on the age-hardening character- istics of the alloys. Stability of properties was determined by hardness and tensile testing of the alloys at room temperature after various periods of exposure to elevated temperatures. Precipitation-hardening curves are shown for a number of magnesium-lithium-zinc alloys in fig. 1. All the alloys were solution treated at 700°F and aged at 200°F. The reason for using the drastic quench, toluene at —105°F, was to reduce the rapid precipitation of the hardening phase which takes place at room temperature. Previous experience has shown that a hardness of about 90 to 95 Rockwell E is indicative of yield strengths in the range of 35,000 to 40,000 psi. This is a desirable strength level for magnesium-lithium base alloys with specific gravities of the order of 1.65 or less. Although the hardness level is raised by large zinc contents, a corresponding decrease in the cold formability of these alloys occurs with increasing zinc content. Thus, alloys containing up to about 10 pct Zn and having hardnesses of the order of 70 to 75 Rockwell E may be bent over a very small radius; however, the 16 pct Zn alloy requires a bend radius of more than 8T. The hardness relationships illustrated in fig. 1 can be explained by the partial phase diagram shown in fig. 2. The zinc-free magnesium-lithium alloys are entirely body-centered cubic (100 pct beta phase) when the lithium content of the binary is 10.3 pct or higher. When zinc is added, the boundary between the beta and alpha-plus-beta fields at 700°F is shifted to lower lithium contents. In addition, the solubility of zinc at 700°F decreases with decreasing lithium content. It is shown by a study of micro-structures that the limit of solid solubility of zinc in the 6Mg/Li* matrix at 700°F is about 19 pct. It is believed from a study of the aging curves that this limit is about 2 to 3 pct at 200°F. Zinc additions up to about 2 pct increase the hardness and strength of the magnesium-lithium base solid solution. Larger additions of zinc effect further hardness increases, but precipitate during prolonged aging at 200°F. Alloys having 14 to 20 pct Zn precipitation harden extremely rapidly during quenching, even when quenched in toluene at —105° F. The high-zinc alloys overage at 200°F but are capable of maintaining reasonably high hardnesses for periods up to 1000 hr.

Jan 1, 1951

Operating Characteristics of Centrifugal Fans and Use of Fan Performance Curve Discussion of paper by. Louis W. HUBER, presented at the New York Meeting, 1926, .and issued, as Pamphlet No. 1542-A, with MINING AND METALLURGY, February, 1926. G. BRIGHT, Pittsburgh, Pa.-Apparently from the pressure curves for a forward-curved-blade fan, in Mr. Huber's paper, practically all ventilation-might be stopped with increased resistance. In order, to discuss the characteristics of a fan we need, some better way to measure the characteristics of a mine. You all know that. the average anemometer is not very-reliable. Sometimes two anemometers, supposed to be recently calibrated, will differ 50 per cent. Either this or some other committee should standardize measuring methods. The characteristic curves of fans, given by Mr. Huber, would indicate that the forward-curved-blade fan would cause trouble in attempting parallel operation, because two machines will not parallel unless they have dropping pressure characteristics. On the other hand, it is indicated that with the backward-curved blade, they could easily be paralleled. But few mines use more than one fan. Mr. Huber said that if the resistance of the mine was considerably more than contemplated, the quantity of air might be such that the efficiency of the backward-curved fan would be seriously affected, dropping say from 70 to 55 or 50 per cent. In such event, could a difference of speed be selected for the fan that would give the quantity desired at a higher efficiency? L. W. HUBER, Pittsburgh, Pa.-The backward-curved-blade fan responds to change in speed the same as any other fan; if' the speed is doubled, the quantity of air is doubled, the pressure is increased four times and the horsepower eight times. One point not mentioned in the paper is that the backward-curved fan is more efficient than the forward-curved or any other type. If the latter were more efficient, it would pay to install that type and keep the resistance of the mine constant, which is hard to do but it can be done with care. But the total mechanical efficiency of a fan with backward-curved blades is from 10 to 20 per cent. higher.

Jan 1, 1927

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and then (2) cover the various aspects of the major raw materials used to make glass. Some of the items covered are: type of materials, their function in glass, their composition, cost, and the relative quantity used in glass vs. totals produced. In addition, a discussion of glass raw material specifications, some byproduct materials used in glassmaking, and comments on future prospects related to the environment, technology, and growth are included. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks, the reader is referred to the commodity chapters in this book.

Jan 1, 1975

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Hugh Douglas

ANTIMONY Antimony (Sb) has been used since the early Egyptian dynasties. Prior to World War I, total demand amounted to only 6000 to 7000 tons per year (tpy). Wartime uses and rapid rise of industrialization in the Northern Hemisphere nations have pushed world antimony use to the 78,000-tpy level. An overwhelming supply of low-cost antimonial resources in the Sino-Russian bloc countries has and will continue to have a major impact on availability and price to users outside the bloc. Table 14.4.1 shows trends in world production, United States production and consumption, and prices. Demand Antimony is used principally as an alloy in lead-based metals and other alloys. Pure metallic antimony usage is small and is confined to such areas as laboratory and electronic applications. Lead-antimony alloys are used in automobile storage batteries, chemical pumps, and pipes, tank linings, roofing material, and cable sheaths. The metal increases the hardness of lead, and, for such uses as foundry printing type, reduces shrinkage for casting and lowers the melting point. Antimonial oxides are used for ceramic purposes, white paint pigments, glass forming, textile finishing, fire retardants in military clothing, matches, and solder. Wartime applications include use as hardener for bullets, an element for tracer bullets, and ingredient for producing dense white smoke for visual markers. A small but rapidly growing use for antimony is for metallic compounds in semiconductors and thermoelectric devices. In the United States demand for antimony is about evenly divided between metallic end-use markets and nonmetallic markets. In metallic end uses, antimonial lead accounts for 27% of total metallic and nonmetallic use; in nonmetallic areas major uses are flame retardants (15%) which is the fastest growing market, plastics (13 % ), and ceramics and glass (11%). While antimony has advantages in most of its applications, there are uses in which other materials can be substituted, including: mercury, titanium, lead, zinc, chromium, tin, and zirconium in paints and pigments; tin in sheathings; calcium in battery plates; and bismuth in type metal. Supply Antimony is produced from both antimony ores and as a byproduct of smelting other ores. The principal ore mineral is stibnite (Sb2S3), along with its oxidized antimonial minerals and derivatives which occur in small discontinuous replacement veins or fissure vein implacements. Stibnite occurs in quartz-gold veins and copper-lead-zinc

Jan 1, 1976

Boiler-Room Economy "Establishing and Maintaining Boiler-room Economy" is the title of a paper presented before the Ohio Society of Mechanical Electrical and Steam Engineers by Geo. H. Gibson, of which the following is an excerpt: Boiler-room economy depends less upon equipment than upon operation, i.e., it depends largely upon the condition in which the apparatus is maintained and how it is used. A given boiler may operate this week with an efficiency of 78 per cent., and next week with an efficiency of 65 per cent., while using the same fuel and developing the same rating. If there are variations ii; character of fuel and in load and other factors, the falling-off may be even greater, possibly to less than 60 per cent. The steam produced may cost twice as much per 1,000 lb. at one time as at another. Most steam plant managers know from their own experience that these statements are not exaggerated. It does not take much of a plant to run up a coal bill of $5,000 per year, many "spend $10,000 for coal, and fuel bills of $50,000, $100,000, or $200,000 per annum are not uncommon. As it call be shown in the majority of these plants that 10 per cent. of this amount may be saved, and in large numbers of them 25 per cent., while in some the expenditure can be cut in half, there is no disputing that we have here a subject worthy of attention. In the production of steam the greatest variable is the human factor. Before we can pass judgment, however, we must first have standards. This implies accurate quantitative knowledge of fuel consumption and steam production. We must measure the output and know how much the steam costs per thousand pounds, and how many pounds of steam are obtained from a pound of coal. We can then begin to analyze the problem, and find where and how methods and conditions can be improved, and how much. Many favor buying coal on a B. t. u. basis. This is advisable where the amount purchased warrants the considerable expense involved in systematically gathering samples that: are. truly representative and in having analyses made, of every carload. Coal analyses, combined with. an honest endeavor on the part of the miner to ship good coal, should insure the receipt of the heat units paid for. , It often happens, however, that the coal which is cheapest on a B.t.u. basis is not the cheapest or most suitable for producing steam, because of peculiarities of the plant in which it is to be burned, or conversely, the fuel which furnishes cheap B.t.u. may require special methods or equipment for its economic utilization.

Jan 2, 1916

By C. S. Matthews, M. J. F. Rosenbaum

The purpose of thir work wax to lcarn it~lzut infori~lation could he obtained from various typs of pilot water floods and to attempt to find the optunum pilot patter11, for a revervoir which had previously been depleted by a solution gas drive. The study was made in the laboratory with mathemetical methods a dynamic analog and a potentiotnetric analog. Results werp tested against the field llistorics of a nrrnlber of pilot water floods. At a reasonable valrre of currzulative injection, the total production rate for the one-injector five-spot should reach about 6.5 per cent of injection rate, and for a four-injector five-spot, about 9 per cent. Accurate estimates of ultimate recovery cannot be made on the basis of such snzall prorluction rates. However, with a pilot composed of nine ir1jector.s and 16 producers the production rate is approximately 50 pcr cent of injection rate at a reasonable value of camulative injection. Sonle inforn~ation for extended performance predictions might he obtained from such a large pilot. These conclusions were drawn on the basis of results obtained for unit mobility ratio, and a sturly using tlre potentiometric analog was made of the effect of other mobility ratios to determine the range of applicability of these predictions. For the four-injector, five-spot pilot with the ratio of production to injection rate (before water breakthrough) is about twice that for with it is about two-thirds; and with M0= 10, it is about one-third For high mobility ratios, it was found that the production rate increased considerably as water-cut increased. These result can be used to modify, qualitatively, the inter.pretntions based on curves for the unit rnobilit\. ratio CaSeS. It was found that the maximum ratio of production rate to injection rate obseriled in field pilot floods was of rhe scime order as that prerdicted by these methods. The time required to reach thisr maximum did not generally agree with the time predicted for a homogeti~orir reservoir. The differcrlce between predicted and observed time of response gives an indication of the permeability profile and of the condition of the producin,g wells. Pilot water floods of the pattern type are generally carried out in reservoirs which have been depleted by solution gas drive and are at low pressure. Under these conditions, oil and water can be considered incompressible. It is assumed that, as the water is injected, an oil bank forms ahead of it and that there is a distinct interface between the water zone (or bank) and the oil zone (or bank) and between the oil zone and the region ahead of the oil zone. It is further assumed that only gas is mobile in the unflooded (gas) region, only oil is mobile in the oil bank and only water is mobile in the water bank. The saturations and the mobilities associated with each zone are assumed uniform. We idealize our reservoir to be homogeneous, horizontal and of constant thickness. Effects of gravity within the producing layer are assumed negligible. If the actual time-dcpendent flow problem is approximated by a acries of steady-state problems. the potential and stream function in the oil bank and water hank satisfy Laplace&apos;s equation in two dimensions. We can therefore use a poteiitiometric analog of this system. Potentiometric models have yielded uscful results in this laboratory&apos; and clsewhere in the study of a variety of secondary recovery problems. For the case where M = I, we generally prefer to use theoretical mcthods as well as a simpler dynamic analog. Except where otherwise noted, the ratio, side of five-spot/wellbore radius. is taken to be 3,600. a figure which corrcsponds to a normal-size wellbore in a 10-acre well spacing. THEORETICAL EVALUATION OF VARIOUS PILOT PATTERNS, Mw0 = 1 <&apos;he theoretical models which we used to examine the performance of various pilots are shown in Fig. 1. Image theory was used to determine the ratio of production rate to injection rate as a function of the volumc of the flood. The ratio of production rate to injection rate was chosen because this is an easily measurable quantity which is characteristic of a pilot

By R. G. McQueen, E. G. Zukas

THE production of isotropic fine-grained ingot iron would be most useful since physical measurements associated with the elastic properties of iron are influenced by the size and orientation of the individual grains. This can be accomplished at present for small samples by established metallurgical procedures, but for large samples (in excess of 2 in. diam by 1 in. thick) it is virtually impossible to produce reasonably small uniform grains with random orientation. Such pieces can, however, be produced by impulsive loading followed by a suitable recrystallization treatment. The shock loading system employed is diagrammed in Fig. l. Here the 3/8-in. iron plate is accelerated by the plane-wave initiated high explosive charge through a 1 5/8-in. air space. Collision of this plate and the specimen of interest generates a shock wave in excess of 300 kbars which passes through the specimen. For this type of work it is not necessary to use machined parts: for example, the ingot iron pieces are saw cut from the billet so that they can be inserted in short sections of iron pipe. The recovered specimens are less distorted, however, if the air gap between the iron sample and pipe is filled with Woods metal. The dimensional changes resulting from this type of loading technique are minor, usually less than a 10 pct reduction in thickness. Compressive yield

Jan 1, 1962

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors&apos; opinion it was prob¬ably at least 5 million tons. The total fuller&apos;s earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world&apos;s 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By Lucien F. Trueb

The microstructure of explosion-bonded pairs of similar and dissimilar metals has been investigated by electron microscopy. A review of the specific problems encountered and the methods used for obtaining surface replicas and thin-film transmission specimens of the bond interface is given. The bond area is mainly characterized by continuous and practically diffusionless metallurgical bonding. The very large shear stresses induced along the collision front of the plates being joined causes extreme grain elongation and a symmetrical pattern of subgrains in the bonding direction. The bond zone is also characterized by a very high density of dislocations and pressure-induced twins. Localized heating occurring during the cladding process can result in partial re-crystallization or the formation of thin layers of molten material. The force of precisely controlled explosions causing a high-velocity impact between metal plates has been used for several years to achieve metallurgical bonding between an extremely wide variety of metals. This method essentially consists of accelerating a plate to high velocity toward a stationary plate by a detonating explosive. Since the restrictions to bonding are not those encountered with conventional nethods, it becomes possible to bond pairs of metals having widely different mechanical properties that are immiscible or form brittle intermetallic compounds. Many applications of such composite metals are found in the field of corrosion protection as well as numerous other fields; for example, explosion bonding is being applied for fabricating the materials used by the United States Mint in the new sandwich-type coins. The primary condition for establishing a metallurgical bond is that absolutely clean metal surfaces be brought together. Any metal exposed to the atmosphere is covered with oxides, adsorbed gases, and other contaminants; even a very forceful impact of two such surfaces is not sufficient for bonding. Cowan and Holtz-man,"&apos; who reviewed the dynamics of colliding plates in detail, showed that in order to achieve a good bond the explosion conditions must be chosen in such a way that the plate collision velocity is less than the sonic velocity, in which case no oblique shock waves are attached to the collision front. A pressure wave is then generated ahead of the collision line, and the material forming the colliding surface of each of the plates flows forward and is ejected in the form of a spray, the so-called jet. The dynamic elastic limit of the metals must be exceeded so that there is sufficient plastic deformation. At the point where the jet formed by the junction of the inner surface layers of both plates separates from the combined plates, the material experi- ences a very high shearing strain and the pressure can reach several hundred kilobars. This process strongly influences the microstructure of the bond zone as will be seen later. Behind the collision front, uncontami-nated layers of internal material are brought together under high pressure and are thus metallurgically bonded. I) STRUCTURE OF EXPLOSION BONDS The different types of explosion bonds that can be obtained depend on the explosion conditions, and have been investigated by Cowan and Holtzman,1&apos;2 Holtzman,3 Klein; Bahrani and crossland,&apos; and Buck and Horn-bogen. The preferred kind for practical applications is the so-called wavy bond, typical examples of which are given in Fig. 1 showing light micrographs of various metal-to-metal interfaces. In forming this type-- of bond the collision energy is mainly expended in jetting, the formation of waves, and localized melting. Beyond the crest of the waves, eddy-shaped areas are observed in which the two metals are mixed in a complex pattern of streaks. Cowan and Holtzmanl first proposed that this wavy pattern is analogous to periodic eddy shedding in the flow of a viscous fluid around an obstacle (Von Karman&apos;s eddy street). The mass of metal ahead of the stagnation point, which is associated with the jet and has forward momentum, plays the role of an obstacle and the eddies created in the flow of solid metal around the stagnation point are preserved in the final clad specimen. This idea has been reviewed more recently by Klein4 and the variables involved in the wave formation have been discussed in some detail by Bahrani and crosslands and Buck and Hornbogen.6 Several studies of the structure of explosion bonds by light metallography have already been published.1-6 Aside from the waviness and the eddies which were mentioned above, the most striking characteristic of the area in the vicinity of the bond interface is a very considerable longitudinal grain deformation which appears to be strongest at the metal-to-metal boundary and dies out as one moves away from it. Large twins are often observed within the deformed grains, and molten areas are found in the center of the eddy-shaped structures situated beyond the crest of the waves. The large hydrostatic pressures and shear stresses occurring at the interface modify the mechanical and chemical properties of the bond zone. Increases in hardness in this area have been reported by various authors.396 The defects along the interface can also cause a local increase of the chemical reactivity and thus might be expected to boost the etching rate. However, the effects of this preferential etching cannot be observed by light microscopy due to its inherently limited resolution power. The same limitation precludes the observation of morphological features directly along the bond interface as well as the interface itself. Furthermore, no information can be gained by light-

Jan 1, 1969

By R. A. Davidson, L. Silverman

RESIDENTS of many urban centers are becoming increasingly aware of the obscuring effect of fume and smoke discharge from power, metallurgical, chemical, and other industries; and they, as well as the legislatures of these affected cities, are agitating for cleaner air. Management&apos;s most pressing problem is to find an economical way to reduce process effluents in response to the growing pressure from population and legislative demands. The removal must be done, if possible, without handicap to the current operation, since the costs of relocating are often excessive or prohibitive. In fume recovery or disposal, an important item to consider is whether or not the material being discharged has any value. If it has commercial value, the cost of its recovery may offset or aid amortization. For this reason, in making a study of the specific problem in hand, a major factor was the nature of the material emanating from the stack: in particular, its particle size, size range, and its chemical and physical composition, as well as its potential value and utility when recovered (in either a wet or dry state). Should the product have no commercial value, it must be disposed of at minimum cost in a way to prevent recontamination. Initial studies were therefore made to determine stack concentrations and volumes of material evolved from the operations. The next phase of the study concerned the physical and chemical nature of the collected fume. The third portion of this paper describes the wet and dry collector studies undertaken to recover the fume. Cleaning Requirements for Ferroalloy Furnace Operation The basic need for any effluent collection equipment is the highest possible efficiency and the lowest tolerable resistance when the power consumption involved is considered. Since the electric furnace effluent is largely composed of fume of small size (less than 0.5u), it has high light obscuring properties, and even low concentrations will cause some loss of visibility and be evident to nearby residents. The permissible limit for fly ash emission in many cities is based on a weight value (viz, approximately 0.4 grains per cu ft), but the smoke density values are dependent upon a shade of color. In the case of the Los Angeles County code, emission is restricted to pounds per pound of material processed per hour basis (but not exceeding 40 lb per hr for any one given plant operation). If an average particle size of the fume from ferro-silicon alloy electric furnaces is assumed to be 0.4u (as shown later, this is the approximate mean size) and an average loading of 1 grain per cu ft (stp), each cubic foot of stack gas will contain approximately 75x10 10 particles (based on assumed, and confirmed, spherical shape and a standard deviation of unity). When it is realized that the air in metropolitan areas, which are also general industrial areas, contains approximately 5x108 particles, the tremendous light scattering effect of this concentration becomes apparent. Consequently, nearly 100 pct collection would be necessary to equal the average concentration. Fortunately, however, discharge from a high point above ground (50 to 100 ft) will result in at least a thousandfold dilution, or the stack concentration reaching the ground in the foregoing case might result in a ground concentration of &apos; particles. If the concentration at the source could be reduced by a factor of 100 (99 pct efficiency of collection), then a concentration of 75x10" particles would be diluted to 7.5x10&apos; which would be very satisfactory. An efficiency of 90 pct (factor of 10 decontamination) at the source would result in a discharge of 75x109 articles which upon dilution yields 75x10 which is still 15 times the general air value. Another approach to this consideration is to use the value of concentration of 0.005 grains per cu ft for the value of a visible effluent as cited by Kayse.1 To attain this value with an average loading of 1 grain per cu ft would require an efficiency of 99.5 pct. Since the foregoing value is not based on any reported size of fume particles, it is felt that the numbers&apos; approach given previously is more reliable. These calculations serve to indicate the desirability of thorough cleaning, preferably at the source, and with efficiencies well above 90 pct, preferably above 95 pct (dilution 1:20). One of the most important items in any control program is to reduce the concentrations as close to their sources as possible. The use of better furnace design, deeper coverage over the electrodes, and the prevention of blows or breaks in the surface all help to reduce dissemination; consequently, all of these improvements should be made, if possible, to cut down the effluent load. In addition, in order to minimize the volume of contaminated air that has to be cleaned, the furnace should be enclosed as much as possible. Test Arrangements Before fundamental studies with collectors were made, a furnace stack selected for the test program was sampled to determine the gas temperatures and

Jan 1, 1956

By Frank Alfred Fahrenwald

Discussion of the paper of FRANK ALFRED FAHRENWALD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 103 to 149. F. A. FAHRENWALD, Cleveland, Ohio (communication to the Secretary*).-Since the publication of my paper in the January Bulletin, (which was largely a metallographic treatise), I have been questioned regarding two points referred to therein. One of these is that which deals with the application I have made, p. 119, of the equation for melting pressures which correspond with different working temperatures. The other refers to the statement, p. 137, that "Prolonged heating at relatively low temperatures gave fewer and larger crystals and crystals of different sizes, while a flashing at higher temperatures gave a very fine and uniform crystalline structure, which was much&apos; to be preferred." Especial emphasis was not placed upon either of these two factors, for each seemed perfectly logical and obvious. As they do not seem to be self-explanatory, I will supplement with those portions of my notes which were purposely omitted from the manuscript submitted for publication. A few practical illustrations may serve as evidence in support of the first of these, but it must be understood that in this work the "amorphous theory" is considered as being sound, and that it is assumed that metals allow of distortion, without fracture, by virtue of the formation of slip surfaces, accompanied by the transformation of crystalline material to the, amorphous phase. Effect of Pressure.-In all forging, rolling, and drawing operations, it is known that specimens of small cross-section may be worked at a lower temperature than can be used for the same material in much greater mass and sectional area. In -the larger pieces the maximum pressure is brought to bear upon the material near the surface, so that the interior is not subjected to great pressure, but to, a stress more nearly tensile, or shearing, so only the surface is subjected to the critical melting pressure. In the case of wires which draw hollow, the center is subjected to practically a tensile stress which breaks it, while the surface skin draws perfectly, due to the enormous "flowing" pressure exerted upon it by the surface of the draw-plate.

Jan 5, 1916

By E. P. Barrett, T. L. Joseph

The large iron-ore producers on the Mesabi Range are able to maintain the silica in their shipping products at from 8 to 10 per cent. by mixing ores of various grades, some assaying 4 per cent, silica and some as high as 18 per cent. silica. For each ton of 4 per cent. silica ore mined, a ton of 14 per cent, silica ore can be mined and mixed with it and the average grade maintained at 9 per cent. This mixing operation has made possible the utilization of large quantities of ore too lean to be used alone, and herein lies the advantage of the producers who operate a number of mines at the same time. As the grade of the ore from one of the properties falls off, a little high-grade ore from another property can be mixed with it and the average maintained, while if one property alone were being operated all of the ore below grade would be left behind. This mixing operation, however, can continue only as long as there is high-grade ore available for mixing with the high-silica ores and, while the tonnage of iron ore in the Mesabi Range is still enormous, the tonnage of high-grade ore suitable for mixing with any quantity of low-grade ore is being rapidly depleted. Obviously, if an 18 per cent. silica ore can be reduced by concentration methods to 12 per cent. silica, considerably more of it can be utilized with a given amount of high-grade ore. The operators on the Mesabi Range recognize this situation and are energeticdly endeavoring to reduce the silica in their concentration plants because every unit of silica that can be removed by concentration is a conservation of their high-grade ores. More Elaborate Processes Will Be Needed At the present time there are thirty-seven concentrating plants on the Mesabi Range, and about one-third of the total ore shipped is beneficiated in these plants. In about one-half of these plants no reduction is made in the silica but the moisture or structure of the ore is improved. The washing process is by far the most important method for the removal of silica, and it is interesting to observe that the tonnage of "wash" ore during the past five years has shown practically no increase although the total tonnage of ore shipped has increased. This is due to the fact that the available tonnage of wash ore is being depleted and the amount

Jan 1, 1930