Search Documents

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

By John H. Bassarear, Harold W. Sorstokke

The fourth expansion within 10 years was completed at Pima Mining Co. during late 1971. The first three expansions increased capacity from 3000 to over 40,000 tpd. Conventional crushing and grinding practices were used in the original 10-section mill. Total capacity is now approximately 54,000 tpd. Expansion IV includes a new primary crusher and a radial stacker conveyor that feeds stockpiles for both concentrators. The -8-in. primary product is fed from the reclaim stockpile to the new mill by two pairs of pan feeders, each pair feeding a separate conveyor. The reclaim conveyors each feed 28 X 12-ft semiautogenous mills operating with an 8% charge of 4-in. balls. Autogenous discharge is screened, oversize recycling by conveyors, with -%-in. undersize feeding two conventional 161/2 X 19-ft ball mills in closed circuit with cyclones. Cyclone overflow is pumped to three parallel rows of 300-400 cu ft flotation cells. Rougher and scavenger concentrates produced are sent to the original mill for regrind, cleaning, and filtering.

Jan 1, 1974

By Paul Tyler

THE ferroalloying elements are connecting links between the steel industry and the nonferrous metal industries. Although ferroalloys are distinctly nonferrous themselves, they serve the steel industry either in the manufacturing process or in modifying the product-in some cases so that it may compete in the markets with nonferrous metals. Of the 92 elements generally accepted by chemists as constituting the primary building blocks of matter, all but the very rarest have been investigated with a view to employing them in steel manufacture. The surprising thing is that so few have been found commercially acceptable. Despite the relatively small number of elements involved, the employ-ment of alloys in steelmaking is one of the most complicated and probably one of the least well understood of modern industrial enterprises. A great deal has been written regarding the action of individual elements and a profuse and somewhat acrimonious literature covers pretty much the whole field of ferroalloy ore supplies. In the middle ground between the miner and the steelmaker developments are less carefully watched by most observers, and except for an occasional description of the technique of some conversion process or the tariff hearings in Congress, very little is said about them. The purpose of the present paper is to describe in relatively nontechnical terms this highly complex industry and to study its relations to our national progress.

Jan 1, 1933

By D. L. Archer, W. W. Owens

Conventional waterflooding often is uneconomic in highly fractured reservoirs because of the gross bypassing of the reservoir oil by injected water. Imbibition and pressure pulse flooding have been used in at least one fractured reservoir in an attempt to achieve better oil recovery performance. This paper presents the results of laboratory flow tests conducted on large cores to evaluate the possible applicability of these methods (particularly pressure pulse flooding) to different types of reservoir systems. Test data were obtained on both water-wet and oil-wet systems, and on systems having two widely different levels of compressibility and flow capacity. Results indicate that pressure pulse recoveries from fractured reservoirs will likely not exceed 5 to 10 per cent pore space with maximum response achieved during the first pulse cycle. Improved recovery by this method is possible from both oil-wet and water-wet reservoirs. Comparable saturation distributions during imbibition and pressure pulse production suggest that an initial pressure pulse cycle to speed production response would not interfere with subsequent imbibition flooding in water-wet reservoirs. INTRODUCTION There is a steady increase in the number of fluid injection projects being initiated each year to improve oil and gas recovery over that obtained by primary production mechanisms. Experience gained in different geographical areas and with different recovery methods is teaching that reservoir anatomy is one of the more important factors controlling the success or failure of such projects. Fractured formations appear to be the rule rather than the exception, especially in carbonate reservoirs. Conventional methods of fluid injection, whether it is waterflooding, gas injection or miscible flooding, have limited applicability to highly fractured reservoirs because of the severe bypassing of reservoir fluids. The result is early breakthrough of the injected fluid and rapidly increasing ratios of injected to in-place fluid with an undesirable effect on return on investment. Thus, innovations to conventional methods must be developed if recovery from fractured reservoirs is to be optimized. One new method proposed for application to highly fractured reservoirs is pressure pulse waterflooding. Although pressure pulsing with gas has been suggested' and rested in at least one reservoir; the Sohio Oil Co. is generally credited with the development and testing of pressure pulsing in conjunction with waterflooding. Publications" of Sohio's waterflood operations in the Spra-berry Trend indicate that the idea for pressure pulse flooding evolved from a critical analysis of the disappointing early performance of their flood initiated in a portion of the trend in April, 1961. This flood was planned to take advtantage of imbibiltion and high pressure gradients across the reservoir matrix blocks (unfractured Mocks of the reservoir rock which are visualized to be generally surrounded 'by the fracture system) evaluated in pilot tests by the Atlantic Richfield Co.5 and Humble Oil & Refining Co.' However, the early recovery and pressure performance of this flood indicalted that high pressure gradients induced between the fracture system and the centers of the matrix blocks were forcing water into the periphery of the blocks and temporarily interfering with the counter-current flow of oil due to imbibition. Fill-up in the blocks was occurring with re-solution of the free gas phase as pressures climbed above the original reservoir bubble point. It appeared that cessation of water injection to permit the capillary forces to become dominant and that expansion of the rock and its contained fluids during pressure reduction might aid in expulsion of oil from the rock matrix into the fractures. Subsequent production performance. aflter cessation of injection, proved this hypotheslis correct. Thus, pressure pulse waterflooding was born. Pressure pulse flooding appears to have several advan'tages over imbibition type flooding in highly fractured reservoirs. First, all wells may be used for water injection which should hasten fill-up and achieve a more rapid increase in reservoir pressure. Second, because of increased injection pressures and rates, flooding gradients will force water into the reservoir matrix more rapidly than would be achieved by imbibition alone. Third, during the pressure depletion cycle of the flood, the compressibility of the system, which has been increased by resolution of the free gas phase, provides energy for the displacement of oil at a rate greater than would correspond to countercurrent flow during imbibition. Fourth, during depletion all wells may be put on production, thus contributing to higher oil withdrawal rates on a reservoir-wide basis. One possible disadvantage of pressure pulse flooding as compared to imbibition floodling, however, is that the outer periphery of each matrix block is flooded to a residual or near residual oil saturation during the Water lnjection stage. This zone of reduced permeability to oil m'ay offer greater restriction to the production of

Jan 1, 1967

By C. G. Albert

The clay particles of 2 microns or less required for modern paper coating are predominantly flat plates, lying smoothly on the sheet and producing a high gloss. Operating speeds of today's coating machines necessitate a clay composition of 60 and sometimes 70 pct solids as against the 35 to 40 pct required in the past. Since clays in suspension may solidify in flow, only those of intrinsically low viscosity can be used as high coating solids. THE literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing. The paper industry itself is not the ultimate consumer. For the greater portion of the clay the end product is the printed page, and the demands of printing and publishing have sparked some of the technological advances in paper making which have, in turn, brought about methods employed in the kaolin industry. As compared with the product of 20 or 25 years ago, one of the most striking characteristics of the graphic arts today is the mass production of quality printing of fine pictorial work, much of it in full color. During this time periodicals with printing standards close to those of yesterday's slick-paper publications that were printed on a slow schedule and for a limited circulation have grown to the point where they go out to many millions of readers, often at weekly intervals. The complexity of technological improvements brought about by this increased circulation is probably not appreciated even by technical people, unless they have had reasonably close contact with the industry. The advance has come about through developments not only in the art of printing, but also in the field of paper making and even at the level of clay mining and processing. The smoothness required for faithful reproduction of the kind of printed matter under consideration is attained with a clay-coated paper. Since the distribution expense of the publication will depend to a great extent on its weight, the paper used must not be too heavy. This means a lower basis weight than was normal for conventional clay-coated papers some 25 years ago. And for this mass production market it becomes necessary to provide a paper having these and all the other required characteristics at a very moderate price—not the premium price conventional clay-coated papers formerly demanded. This challenge has been met by a new method of producing coated paper. In the past, application of clay coating to paper was a conversion operation, performed separately from the making of the base sheet. The newer development is called machine coating. Here application of the coating is an integral step in a continuous process by which wood pulp, clay, and other ingredients are manufactured into a sheet of coated paper. Many more problems are involved in this procedural change than are apparent at a casual glance. The coating operation, for example, must function at much higher linear speed than could be obtained with coating mechanisms previously employed. The application machinery developed to meet this requirement necessitated changes in composition of the coating color.* This created new requirements, summarized below, for the clay employed as coating pigment. In addition to smoothness, a relatively glossy printing surface is needed, and to a large measure it is the function of the coating clay to make possible the development of both these surface characteristics. Traditionally, pigments such as satin-white, prepared by reacting lime with paper-makers' alum, were used to assist in producing a high finish. However, economic considerations and others preclude large-scale use of such material in the new processes. In the 1930's Maloney' discovered that a certain particle size fraction of kaolin, consisting

Jan 1, 1956

By T. D. Tiemann

The caustic extraction of silica from Wisconsin and Minnesota taconite was investigated by bomb digestion over the temperature range from 312 to 40S°F at caustic concentrations from 25 to 500 gpl. Residual concentrates containing as much as 65 pct iron were obtained. The high rate of silica extraction is related to a microcrystalline variety of quartz, since it is shown that the rate of extraction of silica from quartz is directly proportional to its surface area. Increasing dependence on foreign ore reserves makes the need for developing the technology necessary for treatment of our low grade ores even greater than it was at the time of World War 11, when much research was conducted on the extraction of alumina from clays. Representative of these were the studies carried on at the University of Illinois.' More recently, the U. S. Bureau of Mines investigated the production of alumina from anorthosite, and currently the aluminum industry is showing renewed research interest in this field. The studies reported here are part of a continuing research program based on the above concepts and aimed at the eventual development of processes for the treatment of low grade ores, particularly those of iron. The fact that large reserves 3 of low grade nonmagnetic taconite are contained in the iron formation of the Wisconsin Gogebic range have made this ore an important and attractive target for investigation. The idea of removing silica by caustic extraction is not new.495 The digestion in caustic solution of ground flint, diatomite, and other forms of chalcedonic silica is the basis for the production of soluble sodium silicates by the wet-process. Upgrading bauxites by the caustic extraction of silica has been investigated6 and is the subject of a German patent.7 Although mention is made by Roe' of the caustic extraction of silica from low grade Michigan and Wisconsin iron ores, and he lists a number of patents and references on the subject, recent work in the field does not appear to be extensive. As far as the author knows, there has been no work in this field on these particular ores. It is hoped that this paper will stimulate further investigation which will eventually lead to an econclmic means of processing these large low grade reserbes. TACONITES The taconites investigated in this study were from Minnesota and Wisconsin. That from Minnesota, a semi-taconite, Nas obtained from the Oliver Iron Mining Division, U. S. Steel Corporation, and represents a sample of an oxidized iron formation from their King Mine on the Mesabi range. The Wisconsin taconite came originally from the trench sampling of the U. S. Bureau of Mines, and represents a composite of the Norrie, Pabst, Yale, Plymouth, and Pence members of the Gogebic iron formation. Assays on these samples are given in Table I. A typical calcu1atr:d average analysis of the Wisconsin taconite is given in Table 11. Chemically, the Minnesota semi-taconite sample contains about 39 pct iron and 39 pct silica, while the Wisconsin taconite contains 30 pct iron and 53 pct silica, both on the dry basis.

Jan 1, 1962

By Walter B. Lenhart

Introduction and Importance of the Industry Sand, as described in this chapter, is a crude product used for ballast on railroads and highways, and as the fine aggregate in concrete, mortar, plaster and in asphalt paving materials. The sand used in glass, as a molding sand, and as a source of silica is described in Chapter 43. Sand and gravel together constitute the mineral raw materials of largest volume produced from the earth. In 1958, as reported by the U.S. Bureau of Mines,21 680,080,000 tons of sand and gravel (including industrial sand) were produced in the United States. The nearest competitor was crushed rock of which 532,818,000 tons were produced. Coal, both bituminous and anthracite accounted for only 431,616,689 tons in the same year. In dollar value, sand and gravel were exceeded only by cement, crushed rock and fuels. Hence it is a major unit of the mineral-producing industry. As an example, one plant in California operates around the clock at an average rate of 1,500 tons per hour, and at peak intervals has shipped over 4,000 tons per hour, all by trucks. Nevertheless, it is controlled by one man through a panel of push buttons that control the crushing, screening, washing, grading, stock piling, and reclaiming of the products. Because sand and gravel are low-valued commodities, but are used in every construction undertaking in every city, village, farm, dam and highway, they are produced in almost every county in the United States and southern Canada, by thousands of individual operators, very few of whom operate in more than one community. Many operations, particularly those established to supply the needs of major dams that are under construction, or of major segments of new highways, are temporary in nature, and the equipment installed is more or less portable. Because of the bulky nature of sand and gravel, there is very little interstate movement, and almost no exports or imports, except a little movement back and forth across the border of the United States and Canada. First, the material needs definition. Definitions Sand and gravel have been defined as continuously graded unconsolidated materials that appear in the earth's surface as a result of the natural disintegration of rocks. Both normally appear together, but in a wide variety of sizes, types and range of size classification. The American Society for Testing Materials has tentatively revised its definition of "sand" as: granular material passing the 3/8-in. sieve and almost entirely passing the No. 4 (4760-micron) sieve and predominantly retained on the No. 200 (74-micron) sieve, and resulting from natural disintegration and abrasion of rock or processing of completely friable sandstone (ASTM Designation C 58-55T). The Society's tentative revision of its definition of "gravel" is: granular material predominantly retained on the No. 4 (4760-micron) sieve and resulting from natural disintegration and abrasion of rock or processing of weakly bound conglomerate (ASTM 125-55T). Sand and gravel deposits contain materials from the finest silt to the largest boulders. Chemical definition of the two materials is nearly impossible. Sand and gravel always are

Jan 1, 1960

By George W. Becker, Blair R. Benner, Ronald J. Roman

A computer model for the leaching of oxide copper heaps is developed and verified in laboratory tests. The model can be used to scale-up laboratory test data and to simulate the results of various operating philosophies on heap leaching. The model is applicable to leaching processes where the rate of leaching is controlled by a deficiency of reactant or diffusion of a reactant through the leached rock. Several examples are presented showing the sensitivity of the recovery vs. time curve to the variables in leaching.

Jan 1, 1975

By Cheri Eby, William R. Eby

INTRODUCTION Pneumatic conveyance systems provide for material placement at high compaction rates in confined spaces. This method of conveyance provides proper roof support and ground stabilization important to underground mining activities. Today underground mining activities are conducted far differently than those of our ancestors, in that the reclamation process is the final step in any mining activity. Responsible mine owners are constantly seeking innovative methods to assist them in their reclamation procedures. During the last few years, particular attention has been paid to previously mined areas, as many of these abandoned areas lay open, imposing a constant threat to humans and animals. Considerable attention is being directed to applying proper methods for the filling and sealing of underground slopes, drifts, tunnels, and adits, because today we are experiencing the effects of past mining activities such as subsidence, acid mine water run-off, buring refuse piles, and underground mine fires. Furthermore humans and animals who have ventured into abandoned mine openings have died from exposure, suffocating gases, and mine collapse. This paper explains the method of pneumatically filling and sealing these openings and underground works by means of employing pneumatic equipment and proper backfill material together, thus achieving high material compaction and thereby providing the complete filling of the voids and alleviation of the mentioned dangers. NEUMATIC SYSTEMS The use of air to transport material is widely used; however, conveying abrasive material (e., rock, earth, and cement) requires certain pneumatic transport systems designed to handle the abrasiveness as well as the size of these materials. The Eby pneumatic transport sys tem, known as a Mobile Stower, in mounted on a 42-foot trailer pulled by a Kenwor th tractor. This arrangement allows for quick mobilization and project set-up. The pneumatic system, composed of several components assembled together, produces the volume and pressure of air required to transport the material. Knowledge of elevation, ambient temperature, and material composition at the locations to be backfilled play a big part in the design and useage of the pneumatic system. In this particular system design, material is placed by a front-end loader into an eight (8)-yard hopper which is located over a belt conveyor. The conveyor transports the material up to an air lock feeder, which is the metering devise used to feed the material into the Tee Injector located directly below. Air is supplied by a positive displacement blower which, in this instance, delivers up to 4400 CFM's of air at 8 to 12 PSI. Horse power requirements to drive the blower are met with the useage of either a diesel engine or an electric motor. A diesel engine enables the Mobile Stower to operate in remote areas. As the air flows through the upstream air piping, it passes through the Tee Injector and picks up the material and conveys it through the material conveyance pipe, (referred to as down-stream pipe), and out the placement nozzle. Depending upon material composition and the amount of tonnage to be moved, either mild carbon steel pipe or specially heat- treated hardened pipe is used for the material conveyance line. The entire pneumatic system is controlled from the operator's console. With the aid of instrumentation, only one person is required to operate the system. Tonnage rates vary in accordance with horse power and air supply, as well as

Jan 1, 1982

By William Kent

THE dynamometer herein described is a modification of the one invented by Mr. Samuel Batchelder, of Boston, nearly forty years ago, a description of which may be found in the Journal of the Franklin Institute, 1843, vol. xxxii,.p. 277, and in the Scientific American of August 31st, 1878. The modification consists in providing a method of making an automatic record, and of indicating more minute variations of the power transmitted. The improved dynamometer was designed by the writer in 1877, and was built a few months since by the Class of 1879 of the Stevens Institute of Technology. The accompanying cut, taken from the Annual Announcement of the Stevens Institute, represents the dynamometer without the recording attachment. It consists, as shown, of two stout cast-iron frames, held together by bolts in bearings, in the top of which frames run two shafts, each carrying a pulley at its outer end and a bevel gear-wheel of 45' at its inner end. One of these shafts is the driving-shaft, connected by belt to the engine or other prime mover; the other is the driven shaft, connected by belt to the machine driven. The power is transmitted from one shaft to the other through two other bevel-wheels of 45' gearing with the first, the shaft common to them and on which they run freely being at right angles to the axis of the two shafts first mentioned, and carrying at one extremity a heavy pendulum. The bevel-wheels being connected, as shown, and the power being applied to the driving-wheel, the two intermediate wheels with their common shaft have a tendency to revolve around the driving-axis, which tendency is a measure of the force transmitted, and is resisted by the moment of the weight of the pendulum. In the Batchelder dynamometer the four bevel-wheels and their shafts are used, but

Jan 1, 1880

By William Bent

THE dynamometer herein described is a modification of the one invented by Mr. Samuel Batchelder, of Boston, nearly forty years ago, a description of which may be found in the Journal of the Franklin Institute, 1843, vol. xxxii, p. 277, and in the Scientific American of August 31st, 1878. The modification consists in providing a method of making an automatic record, and of indicating more minute variations of the power transmitted. The improved dynamometer was designed by the writer in 1877, and was built a few months since by the Class of 1879 of the Stevens Institute of Technology. The accompanying cut, taken from the Annual Announcement of the Stevens Institute, represents the dynamometer without the recording attachment. It consists, as shown, of two stout cast-iron frames, held together by bolts in bearings, in the top of which frames run two shafts, each carrying a pulley at its outer end and a bevel gear-wheel of 45° at its inner end. One of these shafts is the driving-shaft, connected by belt to the engine or other prime mover; the other is the driven shaft, connected by belt to the machine driven. The power is transmitted from one shaft to the other through two other bevel-wheels of 45° gearing with the first, the shaft common to them and on which they run freely being at right angles to the axis of the two shafts first mentioned, and carrying at one extremity a heavy pendulum. The bevel-wheels being connected, as shown, and the power being applied to the driving-wheel, the two intermediate wheels with their common shaft have a tendency to revolve around the driving-axis, which tendency is a measure of the force transmitted, and is resisted by the moment of the weight of the pendulum. In the Batchelder dynamometer the four bevel-wheels and their shafts are used, but

Jan 1, 1880

By R. V. Smith, M. H. Cullender

Rigorous equations for calculating subsurface pres.tures in flowing and static gas wells, and pressures along horizontal pipelines are presented in this paper. These general equations, based on the mechanical encrgy balance, contain no assumptions regarding temperature and can be used with either straight-line or curved temperature gradients. The friction factors recommended in this report are based on an absolute roughness of 0.0006 in. Flow is always considered to he turbulent. Although these general flow equations are solved by numerical means, the methods are as convenient as many of those used today to calculate pressures in gas wells and pipelines. These numerical methods are illustrated for flowing and static columns of gas in wells and for flow in pipelines. The authors believe that the use of these methods will result in more accurately calculated pressures in gas wells and pipelines and that [he methods are more flexible than any in use at the present time. Also, the methods are easily adaptable to automatic computers. INTRODUCTION The problem of calculating subsurface pressures in gas wells and along flowing pipelines has been studied by many investigators with the results that two widely-used methods have been presented in technical literature. One approximates conditions in a gas well or pipeline by assuming that temperature and compressi- bility are constants tor the entire gas column. The other method assumes that temperature is constant at some average value but permits compressibility to vary with pressure at the constant temperature. While these approximations may be justified for relatively shallow and low-pressure wells, they become more and more unrealistic as the calculations are applied to the deeper high-pressure wells. In wells or pipelines where there is an appreciable change in temperature between the inlet and outlet ends of the flow string, it is equally as important to consider the change in compressibility with temperature as it is to consider the change with pressure. Consequently, the methods presented in this paper were developed to provide a workable procedure for calculating pressures in gas wells and pipelines which makes no assumptions regarding either temperature or compressibility. The friction factors recommended for use with the equations were the result of study of published literature and extensive experimental work with gas wells. The F,. values in Appendix IV which contain the friction factor are equivalent to an absolute roughness of 0.0006 in. as calculated by the Nikuradse equation. The absolute roughness of 0.0006 in. was previously published by Cullender and Binckley2 for gas wells; it is in agreement with 0.00065 in. of Smith, Dewees, and Williams1 for gas wells and 0.00065 in. of Baker and Swerdloff4 for pipelines; it is in reasonable agreement with 0.0007 in. reported by the Bureau of Mines and the American Gas Assn.5 for large transmission lines. However, any type of friction factors may be used in the equations by a change in the F, values in Appendix [V].

Jan 1, 1957

By D. F. Haley

THE molybdenite deposits at Climax, Cool., have recently attracted considerable notice, because of their great size, as compared with other known deposits of the same mineral. Climax station, on the. Colorado Southern narrow-gage railway, was at one time the Fremont Pass station on the Denver & Rio Grande. It is 1412 miles northeast of Leadville, and exactly on the divide between the headwaters of the Arkansas and Blue Rivers. Climax station is 11,300 ft. (3444 m.) above sea level. The working tunnel of the molybdenum mine is about 1 mile from the railroad, and 900 ft. above it, at an elevation of 12,200 feet. The climatic conditions are severe, and snow can be expected during any month of the year. Winter sets in not later than Nov. 1, the snowfall is very heavy, and the ground remains covered with snow until June 1, and sometimes even later. From June 1 to Oct. 1, there is much rain and a little snow falls in the late afternoon nearly every day. In October, 1917, there was one of the biggest snowstorms and blizzards of the year. Being just on the divide, constant strong winds blow the fine, dry snow with such force that, during most of the winter, outside work of any kind -is accomplished under most trying conditions. Within a few miles of Climax, some of the richest gold placers of Colorado occur. One of them, McNulty Gulch, was just across on the northeastern flank of Bartlett mountain. This mountain, therefore; was well prospected, and the presence of a bluish mineral and a yellowish one resembling sulphur was known to the old prospectors. They thought for many years that the blue mineral was graphite, and it is difficult to say when it first became definitely known that it was molybdenite. Claims had been staked as .early as 1896, but it is evident that the prospectors at that time were looking for gold. In 1902; several claims were acquired by H. Leal, who drove a tunnel about 900 ft. (274 in.) long, probably to intersect a fault, which shows on the surface, and was thought to be a possible gold carrier. Gold was not found in paying quantities, but throughout its length the tunnel passed through a fractured silicified granite, showing a fairly uniform distribution of a fine-grained bluish mineral, which was finally determined as molybdenite. For several

Jan 8, 1918

IN the preceding chapter on thermochemistry and the reactions in and between metal and slag phases and in the following chapter on fuel combustion the main emphasis is placed on the equilibrium or "static" conditions. This equilibrium viewpoint is not concerned with the rate of change in the process or with the mechanisms or paths followed between initial and final states. The questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling its operation, and also in understanding its limitations. Any treatment of kinetic factors in the open hearth such as is attempted here and in Chapter 22 must at present be largely qualitative and incomplete. We are only beginning to get quantitative data on rates of reaction and diffusion at high temperatures, as indicated in Chapter 15. Empirical data in the literature on furnace operating rates do not help much to illuminate the details of gas-flow patterns and the complexities of heat flow in the many parts of the furnace system. This chapter is intended to give the reader an introduction to the problems of the flow of gases through the furnace system and the flow of heat in this system. An adequate discussion would require several times the space available here; it is possible here only to outline a few fundamentals and to indicate some of the conditions of heat and gas flow peculiar to the open hearth. Several good general treatments of these subjects may be found in the literature (see references at the end of the chapter). For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance. They are also important to the operation of the process, at least to the extent of a general qualitative picture of the movement of gases in the system. MOTION OF GASES IN FURNACE DUCTS Fluid flow in general can vary between the extremes of laminar or streamline flow with a minimum energy loss, to irregular

Jan 1, 1951

IN the preceding chapter on thermochemistry and the reactions in and between metal and slag phases and in the following chapter on fuel combustion the main emphasis is placed on the equilibrium or "static" conditions. This equilibrium viewpoint is not concerned with the rate of change in the process or with the mechanisms or paths followed between initial and final states. The questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling its operation, and also in understanding its limitations. Any treatment of kinetic factors in the open hearth such as is attempted here and in Chapter 22 must at present be largely qualitative and incomplete. We are only beginning to get quantitative data on rates of reaction and diffusion at high temperatures, as indicated in Chapter 15. Empirical data in the literature on furnace operating rates do not help much to illuminate the details of gas-flow patterns and the complexities of heat flow in the many parts of the furnace system. This chapter is intended to give the reader an introduction to the problems of the flow of gases through the furnace system and the flow of heat in this system. An adequate discussion would require several times the space available here; it is possible here only to outline a few fundamentals and to indicate some of the conditions of heat and gas flow peculiar to the open hearth. Several good general treatments of these subjects may be found in the literature (see references at the end of the chapter). For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance. They are also important to the operation of the process, at least to the extent of a general qualitative picture of the movement of gases in the system. MOTION OF GASES IN FURNACE DUCTS Fluid [flow] in general can vary between the extremes of laminar or streamline flow with a minimum energy loss, to irregular

Jan 1, 1964

By George Stone

THE method of making oxide of zinc direct from the ore was invented and developed at the works of The New Jersey Zinc Co. at Newark in the middle of the last century. The process was invented by Burrows, who had not the ability, financial or technical, to work out the details necessary to make it of commercial value. This was done by Col. Wetherill, whose name is commonly attached to this process. The, grate bars used are also frequently called Wetherill grates, which is a misnomer because they were in common use for boiler firing at the time and he never claimed their invention. The invention of the process was due to the efforts of The New Jersey Zinc Co. to find a profitable means of working the ores from Franklin and Sterling Hill, N. J. These are a mixture of franklinite, willemite and zincite, containing about 20 per cent. of zinc. The first attempts were to make spelter, which were not successful, owing to the low grade of the ore and the fusibility of the residue. Failing in this, the next attempt was to make oxide in large muffles and reverberatory furnaces. This succeeded, although the cost of operation was high, the recovery low, and the quality of the product uncertain. In 1855, the new process was patented and has been in successful operation ever since. Essentially, the process is to spread a mixture of coal and ore on a body of burning coal on a perforated grate and blow an excess of air through the grate. The zinc is reduced in contact with the coal, volatilizes and burned by the excess of air in the upper part off the furnace and in the flues. It is then carried to the hag rooms by the excess air and products of combustion which are forced through the flues by fans. In its main features, the process is the same today as at the time of its invention, but the details have been so modified that it would hardly be recognized by its originators.

Jan 9, 1917

There is mitigation for the sorrow of friends and the tragedy of sudden death when that death comes at the height of a successful career. It is not everyone's privilege to die, as has been the wish of many, in the harness—toiling, accomplishing, still necessary to the scheme of things. Nor is it everyone's privilege to leave a monument to his work. Dr. Fred Walter McNair died thus—in the midst of his work of educating, leaving along the path down the quarter century of his presidency of the Michigan College of Mines hundreds of men who, having come under his influence, have been successful in life.

Jan 1, 1924

By Arne F. Westgren

X-ray analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations. Changes in Solubility 1. Determinations of solubility limits in the solid state which show decreasing solubility with falling temperature are made as follows: A series of alloys extending into the heterogeneous region is prepared and quenched fromas high a temperature as possible, whereupon their lattice parameters are determined. Then one or more alloys are quenched from temperatures at which they are heterogeneous and their lattice parameters likwwise determined. For the purpose of determining the parameter the apparatus shown in Fig. 1 has been very useful for it produces sharp films in a short time which can be accurately read. High-order reflections (interferences) from the object are recorded on a film which is placed exactly perpendicular to the X-ray beam. The specimen usually has the shape of a small round bar.l Fig. 2 shows a selection of such exposures of silver-rich Cu-Ag alloys, and Fig. 3 gives the measurements made from these films. Fig. 4 gives the solubility curve which results.2 This curve is shifted to lower concentrations than the curve that is obtained from metallographic or physical methods. The X-ray method unquestionably gives more reliable data

Jan 1, 1931

By A. M. Gaudin, D. W. Fuerstenau

By streaming potential techniques, the zeta potential of quartz has been measured as a function of the concentration of dodecylammonium salts at different pH values. These experiments indicate that adsorption of dodecylammonium ions takes place as individual aminium ions until a certain critical concentration is reached in the double layer, at which point the adsorbed collector ions begin to associate into patches of ions, called hemimicelles. Because of its effect on the surface potential of quartz, pH controls the adsorption of dodecylummonium ions. The value of cooperating agents and nonionized constituents of flotation systems is discussed. Previous investigation of the role of pH in the flotation of quartz with anionic collectors is here extended to an inquiry of how the cationic collector, dodecylammonium acetate, is adsorbed at the quartz-solution interface. The equilibrium amount of this collector adsorbed by quartz has already been measured as a function of concentration and pH. The weight of prior evidence has suggested that two mechanisms are involved in the adsorption of this collector by quartz, but with existing adsorption measurements alone it is not

Oct 1, 1955

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today's portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960