Search Documents

By R. J. Mellen

In a chloridizing roasting and cyanida-tion plant treating a manganese-silver ore, certain experiments pointed out the way to an improvement in roasting conditions by a change in the degree of crushing. The following short article is simply a description of the various changes that were necessary throughout the plant and of the results obtained. There is nothing unusual in these changes but they are of some interest in that they constitute a good many of the alterations usually resorted to in increasing production. In the beginning, the changes were brought about by an experiment that was not successful, but which clearly pointed to means of improving the operation, and is an example of the fact that often experimental work may result in failure and still be of value in arriving at correct fundamentals. This experiment also shows how far a metallurgist can get out of line in his deductions, particularly in a field with which he is not thoroughly familiar. The ore at the plant of Compania Minera Kildun y Anexas is crushed through a 13-in. gyratory, a 3-ft. standard Symons cone crusher and a set of 16 by 42-in. rolls, the latter in closed circuit with two Tyler type 400 screens. The crushed ore is then conveyed to two fine-ore bins. These provide storage and feed for two 6 by 90-ft. kiln roasters, which discharge directly to coolers. The coolers in turn discharge to a 6 by 12-ft. ball mill, where the ore is ground for cyanidation. Laboratory and pilot-plant tests previous to the mill construction had indicated that minus ¼-in. crushing was satisfactory for roasting, although results did not vary greatly with some coarser or considerably finer crushing. The plant was designed for a capacity of 300 tons per day on this basis. After a few months operation, the initial operating problems were overcome and the anticipated milling rate was reached but the results being obtained were not really good. The plant seemingly did not have much excess capacity in any department but the roasting operation was the most critically limiting factor both as to tonnage and the results obtained. If this could be improved there seemed some possibility of improving the total tonnage rate to some extent. Segregation of the calcine into various screen sizes showed that the coarser sizes were not giving the expected recoveries. In all of the laboratory and pilot-plant testing, any limiting conditions as to the percentage of salt used, temperatures, feed rates, etc., had affected the fine material more than it had the coarse, and even in making laboratory tests at this time the mill conditions could not be exactly duplicated. Further laboratory testing indicated that a segregation of the rushed Ore into a coarse and fine product for roasting might result in some improvement in roast-

Jan 1, 1947

By Henry M. Howe

Many direct processes have been proposed for the treatment of oxidized ores of copper by reducing the copper oxide to the metallic state, and by separating it from its impurities by a subsequent fusion. The radical objection common to all the methods which have come to my notice, except those in which sulphur plays the prominent part, is that the very deoxidizing agent which effects the reduction of the copper oxide, inevitably reduces at the same time a very considerable part, if not the whole, of the iron which almost invariably accompanies copper in its ores. The result is that, when the ore is subsequently fused, a very great quantity of the already reduced iron separates from the slag along with the copper, alloying with it, and necessitating costly subsequent operations for its separation. Thus, at Perm, in the Urals," the product of the fusion of ferrnginous copper oxides is a mixture of one hundred and fifty-tive parts of highly cupriferous pig iron with two hundred and fire parts of very impure and ferruginous black copper, containing Pome 10 per cent. of' carbon and iron, though free from sulphur, and of course very difficult to refine. If, in order to avoid this reduction of iron to the metallic state, the reducing action be made feebler, it inevitably results that a considerable part of the copper as well escapes deoxidation; and, consequently, the slags are so rich that it becomes necessary to treat them subsequently in order to recover the copper which they contain. Thus,. in treating native copper, at Lake Superior, where the reducing action is purposely made feeble in order to prevent the deoxidation of the iron, the slags from the first fusion of the ore carry so much copper as to render it imperative to treat them again, which is done in a cupola. And yet, in spite of so far weakening the reducing action as to cause a notable slagging of the copper, a very considerable reduction of iron actually takes place. These are the two dangers which threaten the smelter of oxidized copper ores. If he wishes to avoid slagging his copper, he must have so strong a deoxidizing action as to reduce a great deal of his

Jan 1, 1879

By Sylvan Z. Beer

The factors that determine the yield and crystal size in the two-temperature synthesis of A lp were examined. Low yields and small crystals were associated with low temperatures and pressure. Attempts to grow large crystals in the critical and supercritical region of phosphorus were unsuccessful. Crystal size increases markedly at elevated temperatures. Crystals grown at temperatures as high as 1450° C fluo-resced, under uv excitation, at energies close to the estimated band gap of about 2.4 ev, while crystals grown at lower temperatures tended to fluoresce in the red region of the spectrum. Those grown in the supercritical region showed no ALP fluorescence. Heating the high-temperature-grown ALP under vacuum greatly increased its fluorescence efficiency and moved the emission peak to higher energies. I HE III-V compounds, with few exceptions, have been prepared by the two-temperature method. In its classic form this technique is applicable to closed systems where at least one of the components, in this case the column V element, is a liquid or a solid with a high vapor pressure. One advantage of this method over flow systems is in its simplicity. In addition, because it is a closed system, it can, under the circumstances to be described later, be run at higher pressures of the volatile species than in flow systems. In instances where the III-V compound is soluble in the parent III metal to about 1 mol pct or higher, solution growth can be made to take place by slow cooling. This, for instance, is one way in which single-crystal GaP1 and Inp2 have been grown. Initial attempts to synthesize and grow A1P by this technique were not too successful; the yield was low and the crystals obtained were exceedingly small. The conditions required for improving the yield and growth by this technique were, therefore, sought. Two obvious conditions which could be controlling were examined. These were the temperature of the aluminum and the pressure of the phosphorus. The range of temperatures studied extended from about the melting point of aluminum, 660° to about 1450°C. The latter is dictated by the vapor pressure of aluminum which reaches about 1 Torr at that temperature and the limitations of the materials of construction as described in the next section. The pressure range of interest covers from below 1 atm to above the critical pressure of phosphorus, 82.2 atm. EXPERIMENTAL The Temperature of Aluminum as a Variable. A series of experiments were run in the conventional two-temperature manner. All refractories and quartz were dried by heating at 800° to 900° for a minimum of 24 hr, and usually much longer, before use. The aluminum

Jan 1, 1969

By P. J. Jorgensen, J. H. Westbrook

The anomalous indentation creep of nonmetallic solids is shown to be due to the presence of adsorbed water. Although a specific mechanism is not proposed, it is suggested that the water may be present in two chemically adsorbed states. DEPENDENCE of the indentation hardness of solids on the time of load application was first studied systematically by Hargreaves1 in a study of lead and certain low-melting alloys. This technique has become known as indentation creep and has been exploited particularly by underwood and by Mulhearn and Tabor3 as well as by others.4°7 For metals good correlations have been found between the time dependence of hardness over several orders of magnitude in the seconds range and creep parameters from conventional tests at the same temperature where creep strains were measured over hundreds or thousands of hours. However, Walker and Demer8 and Mitsche and Onitsch9 observed extensive indentation creep at room temperature (particularly for light loads) in certain minerals and in materials such as lithium fluoride and magnesium oxide for which conventional creep is ordinarily not observable unless the testing temperature is at a very much higher fraction of the melting point. Normal behavior was observed' for metals such as copper, i.e., negligible time-dependent flow during room-temperature indentation. Walker and Demer attempted to find some distinctive difference in the surface deformation markings about indentations in the anomalously behaving materials at short and very long indentation times. No significant differences were observed. Increased duration of loading was found, however, to result in an increase in the length of glide of edge-dislocation loops extending into the interior of the crystal. Jorgensen and Westbrook,10 in a recent study of

Jan 1, 1965

By M. L. Sisson, G. H. Rupp, R. L. Hair

THE iron ore supply for the Pueblo plant of CF&I is obtained from the Sunrise mine in Wyoming and the Duncan and Blowout mines near Cedar City, Iron County, Utah. The Sunrise mine is an underground operation while those in Utah are open pit.

Jan 11, 1953

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By Gerhard Derge, J. Warren Stewart

Extrusion processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.' Most writers have confined themselves to a general description of the equipment and products and the engineering aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2"8 Ariotlier limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as coinposition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1940

By Gerhard Derge

EXTRUSION processes are used in the commercial production of a wide variety of products, as indicated by the review presented a few years ago by D. K. Crampton.1 Most writers have confined themselves to a general description of the equipment and products and the engineer-ing aspects of the process. The few studies that have dealt with the metallurgical side of extrusion have been concerned primarily with an examination of the mode of flow of the metal during extrusion. This has been accomplished by the use of composite billets, by scribing grids on symmetrical sections of billets and observing the change of dimensions in the gridwork, or by examining microstructures in extruded sections.2-8 Another limitation of these original studies is that they were confined to the extrusion of very simple shapes, usually rods having a diameter of about one-fourth that of the billet. Tin is particularly well suited to the extrusion of collapsible tubes and similar shapes in which the extruded section is very small in comparison to the diameter of the billet or slug. In modern production, impact extrusion methods are generally employed, therefore the thickness of the slug is small compared to its diameter. Under these conditions the process differs considerably from the processes that have been most fully described in the literature, and it is known that the quality of the product is very sensitive to slight variations in any one of the many variable factors involved, such as composition and structure of the alloy, rate of extrusion, temperature, shape of punch and die. An exhaustive examination of all of the above-mentioned problems promises to produce so many data that it seems advisable to initiate the reports at this time, even though all of the factors outlined have not been examined fully, and to confine this paper to a description of the apparatus and method. Only tin and its alloys with small amounts of copper have been considered. These are the alloys most commonly used in this country for the production of the type of articles already described.

Jan 1, 1939

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

By H. Rumfelt

Strip mining in the domestic coal industry is contributing a greater proportion bf overall production than at any time in the past. U.S. Bureau of Mines statistics show that the percentage of total production mined in 1958 by stripping methods increased to more than 30 pct, up from 22 pct in 1951. The tendency to favor strip and open pit mining exists in other mining activities, but such trends are not as clearly outlined as in the coal industry. Significantly, the depth of overburden in coal properties considered suitable for stripping is also increasing. A depth of 50 to 60 ft of overburden was once considered to be about the maximum amount that could be handled economically. Today, a depth of 80 to 100 ft is frequently taken into consideration for simple overcasting operations (i.e., excavating overburden and dumping it in the spoil position where it remains indefinitely).

Jan 5, 1961

By Andrew L. Mular, K. K. Humphreys

Introduction Estimates performed on potential future plants must by their very nature be either order-of-magnitude or budget (preliminary) estimates. Of the three types of estimates recognized by the American National Standards Institute (ANSI Standard Z94.2), order-of-magnitude and budget estimates are the least accurate. Order-of-magnitude estimates have an expected accuracy of plus 50 percent to minus 30 percent. In other words, it is anticipated that actual project cost will be no more than 50 percent above the estimate and no less than 30 percent below the estimate. Budget estimates, or preliminary estimates as they are often called, have an expected accuracy of plus 30 percent to minus 15 percent. The reason that greater accuracy cannot be expected in performing estimates on proposed new facilities is simply that insufficient data is generally available to permit performance of a highly accurate estimate. As stated in ANSI Standard Z94.2, a definitive estimate, i.e., an estimate with an expected accuracy of plus 15 percent to minus 5 percent," . . is an estimate prepared from very defined engineering data . . . (including). . .as a minimum, fairly complete plot plans and elevations, piping and instrument diagrams, one line electrical diagrams, equipment data sheets and quotations, structural sketches, soil data and sketches of major foundations, building sketches and a complete set of specifications." In other words, the engineering of the project must be fairly well underway to permit a definitive estimate to be performed. Such is the case only after the construction decision has been made, all potential alternatives evaluated, and major expenditures committed for a particular course of action. This situation is beyond the scope of this chapter. The chapter is directed to comparison of various technological alternatives for which site specific engineering data is not generally available. Accordingly, such comparisons can be made only by utilizing preliminary or order-of-magnitude estimating techniques.

Jan 1, 1982

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin: The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most promising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestetn Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1947

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By W. D. Lowry

As most of the industrial activity of Oregon is centered in the Portland area, the foundries there consume the bulk of the foundry sand produced in Oregon. Although a number of the larger towns scattered throughout the state have gray-iron foundries, the sand used by most of them is of local origin. The yearly consumption of foundry sand of all types for the past few war years in Oregon is estimated to have been approximately 40,000 tons valued at about $285,000, of which an estimated 18,000 tons was shipped in from the Ottawa, Ill., district for use largely by the steel foundries. Until 1945 much of the silica sand consumed by the steel foundries in the Pacific Northwest, approximately 50,000 tons in 1944, came from Ottawa, Ill. and surrounding regions. Although some silica sand was shipped in from Belgium in the past, none is known to have been imported in recent years. Early in 1945, a very promising high-grade silica sand being produced near Eugene, Oregon, was introduced, and all but two of the Portland steel foundries are using this new sand. Until a few years ago, the search for good local (Oregon) foundry sands was carried on largely by the foundry supply houses. Recently the Oregon Department of Geology and Mineral Industries has investigated a number of deposits and has carried on and fostered research on the most bromising deposit near Eugene, about 120 miles south of Portland. High-grade silica foundry sand from this deposit is now being marketed in Oregon, Washington, and British Columbia. The Eugene sand is one of the very few outstanding western steel-foundry sands. Field investigations by the Oregon Department show that there are relatively few deposits of sand in Oregon suitable for foundry use. A knowledge of the geology of the state makes this readily understandable. The only major primary sources of the quartz present in sandstones in Oregon are the intrusive masses of granite, granodiorite, and quartz diorite of late Jurassic or early Cretaceous age found in the Siskiyou Mountains of southwestern Oregon, a part of the old Klamath Mountain highland, and in the Blue Mountains of northeastern Oregon. Transportation militates against the development of any possible deposits of foundry sand found east of the Cascade Mountains in central and eastern Oregon because few railroads traverse that area. East of the Cascades, which separate western from eastern Oregon, many of the older sediments of Paleozoic and Mesozoic age have either been metamorphosed or contain much volcanic eruptive material, and even if some of the Mesozoic sediments are highly quartzose in places, they are in relatively inaccessible areas. All the Tertiary sediments there are of continental origin and contain much ash and other volcanic debris, for there was great volcanic activity during much of that period. In western Oregon much the same is true of the Paleozoic and Mesozoic rocks

Jan 1, 1948

By J. J. Scott

This investigation utilizes three dimensional photo-elastic techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by observation of points in slices from the model with a polariscope and solving the data thus obtained by the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. The results of this work provide information on the overall stress distribution in points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type. Underground excavations disturb the equilibrium of the earth's crust and a core of fracture, or altered stress distributions exists around the openings. This fact is well known by mining operators and investigators in the rock mechanics field. Analysis of the stress distribution in the areas around mine workings is a most difficult problem and one which has no simple and direct solution. Some of the approaches used by investigators in attempts to study stress distribution around mine openings involve mathematical analysis, photoelastic techniques, statistical analysis, model studies on brittle materials and observation of fracture patterns. Models involving imbedded strain gauges, gelatin models using imbedded strings to show internal movement, and many other unique laboratory techniques are employed. Work is also being done in mining operations where load cells, strain gauges, photostress material, convergence plugs, dynamic plugs, etc., are used to measure strain which can in turn be used to obtain stress. Some of these devices measure strain from which stress may be derived. All approaches to the solution of stress distribution are hampered by the fact that the earth is not a homogeneous, isotropic and elastic media. Geologic faults, fractures, bedding planes, vugs, variations in material composition, variations in grain size and structure, etc., make it extremely difficult to obtain results which can be universally applied to mining operations. The purpose of this investigation will be to demonstrate the use of three-dimensional photoelastic techniques to obtain the stress distribution in the pillars and roof of a room and pillar mining operation. This method utilizes full analysis of interior points, and thus it may be that small tensile or shear stresses found in the investigation will prove to be of greater significance than the more obvious points of stress concentration found by two-dimensional techniques. A digital computer was employed to simplify and to shorten the time necessary to obtain final results. Application of the computer to problems of this type may enable future investigators to attempt more elaborate analyses than have been previously considered feasible. THEORY Three Dimensional Stress Analysis-Shear Difference Solution:' Photoelastic studies are based on the fact that an optically isotropic transparent solid becomes optically anisotropic when subjected to forced deformation; the degree of optical anisotropy being proportional to the deformation of the material. There are two fundamental laws which govern photoelasticity: 1) Light is polarized in the directions of the principal stress axes, and is transmitted only on planes of principal stress. 2) The difference in principal stresses is proportional to the difference in the indices of refraction along the planes of principal stress. One method used in three-dimensional photoelastic work is to examine a slice of the object by normal incidence and oblique incidence. In normal incidence,

Jan 1, 1964

By Henri S. Swolfs

INTRODUCTION In this paper we present preliminary results of a research program in site characterization methodology. We are interested in under- standing the response of discontinuous rock to mechanical, hydrologic, and thermal loadings. To carry out such a study we selected a field site with simple geology, uniform distribution of lithologies, and easily verifiable boundary conditions on temperature, fluid flow and stresses. The spatial distribution of fractures at the site was established and tests were conducted to determine the temperature field, hydrology, rock-mass properties, and in situ stresses. As part of the study selected borehole instruments were compared to assess their performance and reliability. SITE GEOLOGY The study area is in the eastern part of South Table Mountain, a mesa near Golden, Colo. The exposed cap rock is a single lava flow of uniform thickness (6-7 m) that rests on the clastic sediments of the Denver Formation (Van Horn, 1976). The surface of the cap rock (N. 75º E., 3º S.) is topographically featureless and slopes south- southeast; drainage is predominantly downdip and punctuated by occasional contact springs. The age of the lava flow is 64-65 m.y., or early Paleocene. Paleo- botanic evidence confirms the upper part of the Denver Formation as Paleocene (Van Horn, 1976). "Rapid-rock" analyses of core samples from the lava flow at three depths (0.2, 3.3, and 5.8 m) suggest a uniform chemical composition throughout with an increase in the Fe2O3/ FeO ratio (1.05 to 1.60) with increasing depth, reflecting the existence of a perched water table in the lava flow, To identify the rock

Jan 1, 1984

By Frank Doxey

AT Dominion Steel & Coal Corp. it has long been recognized that continued mechanization of mine operations is necessary in the Pictou, Cumberland, and Sidney coal fields of Nova Scotia. The varied physical conditions in these fields call for special consideration of individual cases before planning is finalized. Because standard equipment cannot be procured which would operate successfully, many experiments have been necessary over the years to keep pace with the progress made in other countries. There are two mines, producing 2000 tpd, located in the Pictou coal field. The field is badly distorted and crossed by many faults. Seams are highly inclined and irregular and vary in thickness from 5 to 40 ft. Entries are difficult to maintain because of squeezing of the coal ribs and movement of the roof and pavement.

Jan 7, 1954

By N. J. Grant, I. S. Servi, A. Chaudhuri

IN a recent paper by Servi and Grant,' it was illustrated that the slip band spacing and stress based on creep test data were related by the equation: d =1/ where d is the spacing in millimeters and v is the stress in psi, based on a more complete equation proposed by Orowan. It was shown further,' that for a. given grain size, the slip band spacing became larger with decreasing stress (and was independent of temperature), until such time that the slip band spacing becomes greater than about one-half the grain diam- eter. When this occurred, the mechanism of deformation in creep of 2s aluminum at high temperature changed from slip to grain boundary deformation (sliding). Additional metallographic evidence is now available which confirms this in a most interesting fashion.

Jan 1, 1954

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By D. B. Grove

THE heavy media separation process plays an outstanding role in the concentration of 4000 tons of zinc ore per day at the Mascot mill of the American Zinc Co. of Tennessee. Of the total tonnage, 72 pct is treated in the heavy media separation plant to reject 56 pct of the ore as a coarse tailing, which has a ready market. Concentrates from this separation are beneficiated further by jigging and flotation. Approximately 25 pct of the total zinc concentrate production is made in the jig mill. Jig tailings are ground and pumped to the flotation circuit where the balance of the production is made. Fig. 1 shows a generalized flowsheet of the mill.

Jan 8, 1951