Search Documents

By André G. Journel

Geological study of the Prony Nilaterite (New Caledonia) began in 1969 and included drilling, geological mapping and laboratory studies. The deposit is the product of weathering of basic rocks. From top to bottom, the following zones can be distinguished: a compact ferruginous cover; ore associated with yellow laterite, containing 1.0-1.5% Ni and low in impurities (SiO2, Mg); an intermediate silicated ore containing 1.3-2.0% Ni and higher percentages of impurities; garnierite ore much richer in nickel (2-4%) but high in SiO, and Mg contents (Mg up to 20%) ; and parent rock, largely peridotites. Distinction between types of ore is essential because the high grade ore (silicated and granierites) is penalized for its high Mg contents that demand additional acid treatment. All studies made distinguish two types of ore, laterite and silicated.

Jan 10, 1973

By C. H. Fulton

Page Introduction........................... 280 Distillation Products from Reduction of Zinc Ore........... 281 Preliminary Investigations..................... 290 Equilibrium of Reaction Zn + CO2 + ZnO + CO in Temperature Range of Condensation........................ 293 Requisites for Successful Condensation................ 299 Discussion............................ 300 Introduction The study of the condensation of zinc from its vapor was undertaken to shed light on certain problems encountered in large-scale electric zine-furnace work. recently conducted. It is a matter of common knowledge that one of the disadvantages of the arc type, electric zinc furnace, is the production of a large amount of blue powder and proportionately little liquid spelter, for, as stated by Stansfield,l "A notable defect in the electric smelting of zinc ores is the difficulty experienced in obtaining the distilled zinc in the liquid state; ...... when zinc ores are smelted electrically, very little liquid metal is commonly obtained, nearly all of the zinc being in the state of powder." This difficulty was not encountered in the electric furnace used12 the main difficulty being the destruction of the fire-brick lining of the large condenser, in certain parts, and the formation of .some oxide and dross coatings on the condensing surfaces. The reason for these difficulties could readily be explained by the infiltration of air whenever the condenser was changed from one retort base to the other, the zinc absorbed in the fire-brick forming oxide and causing rupture by its expending volume. Two facts, however, tended to disprove this theory for the rupture of the fire-brick lining: first, the large distilling retort, lined with fire-brick, which was shifted from charge to charge on alternate bases at temperatures between 1200 and 1300 C., fully exposed to the air, showed no signs of disintegration whatever; second, marked disintegration in the condenser occurred .only in places that were at tempera-

Jan 1, 1919

By Charles L. Mantell, P. P. Napolitano

High-purity tellurium oJ semiconductor grade may be prepared by a combination of electrowinning from tellurium oxide, electrorefining and controlled atmosphere melting, as detailed in the paper. SEMICONDUCTOR devices such as transistors and rectifiers depend upon extremely pure forms of silicon, germanium, and selenium. Although tellurium is chemically related to these elements, it has not been studied as a semiconductor because commercial forms are too impure. Highly purified tellurium would be an interesting starting point for a study of its solid-state characteristics. Tellurium shows a greater electrical conductivity in the direction of the helices or chains forming the crystals than at right angles to the chains, and thus is a semiconductor. Unlike selenium, the conductivity is only slightly increased by exposure to light. Impurities such as Ag, Cu, Au, Fe, Sn, As, Sb, Bi, Br, and I provide accepters and make extrinsic tellurium of the P type. So far, however, no elements have been found which, when introduced, would act as donors. Small amounts of tellurium dioxide enormously increase the thermoelectric power. Many extremely pure metals have been made by electrolytic refining or electrowinning procedures. Tellurium forms compounds in a number of valences, as indicated in Table I. The physical properties given in Table II do not show any unusual conditions which would interfere with the formation of elec- trodes, or the deposition of the metal on a cathode. Tellurium dioxide could be obtained in relatively high purities of 98 pct TeO2 or better at reasonable prices. Tellurium dioxide is soluble in caustic to form tellurites, which are conductive, ionizable, and from which tellurium metal may be deposited at a cathode. Preliminary solubility tests to saturation of tellurium dioxide in approximately 10 pct sodium hydroxide gave the results of Table III. The temperature range is a practical one for electroplating. Electrochemical test facilities were set up and these met the operating conditions of Table IV. For a determination of purity of deposits, there was available a Jarrell Ash Co. quantitative emission

Jan 1, 1964

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By James J. Bean

F. M. Lewis—I believe that density recorders are a prerequisite to all well operated ore concentrators. Well designed density instruments are very accurate and give an excellent record of the steadiness of the operation. Controlling the density of a pulp with an instrument, as described by Mr. Bean, is new and the experiences in developing this controller at the American Cyanimid Co.'s Mineral Dressing Laboratory are very interesting and should be extremely helpful to others who are planning on designing or installing controlling density instruments. Instruments for recording the density of the classifier overflow or flotation feed are rather common in ore concentrators, but there are a number of profitable uses for these instruments that are not too well known. Density recorders with bubble tubes submerged to different depth in a classifier pool give an excellent record of the classifier operation. The loading and unloading of the machine, that is so easily masked in the density of the overflow, can be easily recorded if the instrument is installed at some depth in the classifier pool. On some occasions, two instruments with bubble tubes at different depths give a more candid picture of the irregularities in the classifier operation. When cleaner machines are operated in closed circuit with roughers, a record of the density of the cleaner tails will indicate the circulating load in the circuit and is very helpful in coordinating different operators, because quite often the circulating load will be increasing for some time before the analyses of the products will change. Density recorders are used to record the variations in the dilution of the underflow from thickening tanks and in at least one plant the instrument controls the underflow.

Jan 1, 1951

By H. F. Bishop, F. A. Brandt, W. S. Pellini

The solidification mechanism of experimental steel ingots (7x7x20 in.) was studied by thermal analysis. It was determined that solidification proceeds in wave-like fashion at rates which are determined by the carbon level, superheat, and mold thickness. The thermal cycles of the mold walls were related to the course of solidification. ESPITE marked advances in the field of solid state transformation, metallurgical research has contributed comparatively little exact quantitative data on the mechanism of solidification of metals. There is, therefore, a great need for such data in the various metallurgical industries. The mechanics of solidification of ingots have been investigated in the past primarily by studies of the rate of skin formation as indicated by bleeding or "pour out" tests. The "pour out" method, however, is a tool which gives only approximate information. In the case of alloys with wide solidification ranges, such as irons and certain nonferrous alloys, the method will not work at all; in the case of alloys of intermediate solidification ranges, such as commercial steels, the information may be misleading. Thus, the general adoption of this method has resulted in divergent conclusions regarding the solidification process. Chipman and Fondersmith1 by means of bleeding tests have shown that the linear growth of a solidifying ingot wall follows a parabola of the general form, D = K C, with the start of solidification delayed until superheat is exhausted, as indicated by the constant C. These tests were carried only to a wall thickness of about 5 in. using an ingot of approximately 17x39 in. in cross-section; hence the latter stages of solidification were not studied. Matuschka2-3 indicated that linear solidification of ingots is rapid at first, then slow, but toward the end of solidification the rate becomes extremely rapid again. Spretnak's4 bleeding studies indicated that, wall growth is expressed more rigorously by two parabolas, and that their point of intersection corresponds to a change of solidification mode from columnar to equiaxed. Spretnak also showed that the K values of the first parabola are always the same regardless of superheat. Nelson bled ingots of square cross-section and found that linear wall growth is initially rapid but decreases continually until the end of solidification. He also concluded that rate of solidification in ingots of square cross-section increases 2.15 pct for every 10 pct increase in cross-sectional area of the mold. The mold ratios considered (ratio of cross-sectional area of the mold to cross-sectional area of the ingot) were all less than 2 to 1. The subject of solidification has also been treated mathematically in many cases, but because of the lack of accurate thermal constants and the simplifying assumptions required, as their authors generally acknowledge, they represent only approaches to the actual conditions of ingot solidification. A third method of studying solidification is the electrical analogue method promulgated by Pasch-kis6-7 and by Jackson and coworkers.8 This method treats solidification as a heat transfer problem with the solidification cycle synthesized on an electrical circuit. Paschkis in his treatment of solidification considered the fact, which was generally ignored, that solidification of steel is not simply the growth of a plane solid wall but a more complex process occurring over a temperature range as indicated by the constitution diagram. Undoubtedly, the anomalous results obtained by bleeding tests arise from the inability to measure quantitatively this mushy condition. The shape of Paschkis' solidification curves are more nearly in accord with those of Matuschka, in that they indicate rapid linear solidification at the beginning and end of solidification with intermediate solidification occurring at a slower rate. Paschkis indicates a definite lengthening of solidification time with increasing superheat. Thermal analysis is a direct method providing exact information for all types of metals regardless of solidification range and was thus adopted in the present program to follow the entire course of solidification from the surface to the centerline of the ingots. The method has the added advantage of being adaptable to following the thermal cycle of the ingot mold during the course of solidification. Test Methods The ingots studied were of square cross-section, 20 in. long, tapered from 71/4 in. at the top to 63/4 in. at the bottom, and fed with a hot top 7 in. in diam and 12 in. high. The molds were uniform in wall

Jan 1, 1953

By Richard C. Timberlake

The disposal of phosphatic clays has presented a problem to the phosphate industry since the mining of phosphate rock first began in Polk County. As the flotation process was introduced in the late 1920's the problem of clay disposal was increased significantly since clay is present in proportionally greater quantities in reserves yielding flotation concentrates. Because of their physical character and the tremendous surface area per unit volume, these clays have the characteristic of retaining large volumes of water as they are slurried during processing. The disposal of clay and the recovery of a portion of the water require settling areas with a capacity ranging up to 2 cu ft for each cubic foot of phosphate matrix mined. According to a recent study by the Bureau of Mines, the average cost for disposal of these wastes is 24.5[c] per ton of product. This is a major cost of phosphate rock production.

Jan 12, 1969

AN announcement of the annual meeting to be held in New York, Feb. 14 to 17 inclusive is being mailed to all members. Particular attention is called to the necessity of asking for certificates when you purchase your ticket in order that all may secure reduced return fares.

Jan 1, 1927

By John W. King, S. Ralph Austin

Spurred by recent forecasts of greatly increased demands for uranium by 1980 and beyond, interest is once again focusing on America's western uranium deposits. One of the principal producers in this area is the Gas Hills district in Wyoming, the site of approximately 12% of the known uranium in the U.S., including past production and current reserves. Located on the south flank of the Wind River Basin, the Gas Hills deposits have been recently studied by the Atomic Energy commission for clues to and guides for discovering similar-occurring ores. The ore deposits are confined to a permeable sandstone unit, up to 350 ft thick, at or near the base of the upper Wind River formation of early Eocene age. The uranium occurs in three principal north- south "ore trends," each of which is about six miles long, one mile wide, and separated from each other by approximately three miles (Fig. 1).

Jan 5, 1966

By S. D. Baumer, P. M. Hulme

IN the late thirties, the National Carbide Co. cooperated with C. E. Wood, of the U. S. Bureau of Mines, in his investigation of the relative merits of various desulphurizers, including soda ash, caustic soda, and calcium carbide. Laboratory tests showed that carbide, when it could be made to react, is an excellent desulphurizing agent for molten iron. Sulphur content can be driven to lower levels and higher extractions obtained with carbide than with actionsany of the more common reagents. Wood's results1 are shown in Table I. Unfortunately, as the Handbook of Cupola Operation puts it, the chemical fact that carbide is a good desulphurizer was of only academic interest because it was found to be extremely difficult to devise a practical means to make it react with molten iron. Calcium carbide is formed in the electric furnace at 4000°F and above, and its softening point is probably at least 500 °F above the usual working temperatures encountered in iron and steel practice. Consequently, carbide does not form a true slag but floats as a dry powder on top of the metal and only a very small portion of it ever comes in actual contact with the iron. Stirring with a rabble, or pouring the metal over the carbide, increases the efficiency only slightly. Extractions of 20 to 30 pct can be obtained in this manner, but conventional soda slag treatment can do better than this and do it more cheaply. All attempts to lower the melting point of carbide in order to obtain a reactive, liquid slag have so far proved fruitless. Directly under the arc in a metallurgical electric furnace, carbide becomes highly reactive. Excellent sulphur removal can be obtained without any slag other than a thin layer of carbide." imilarly, good results are obtained by adding small amounts of carbide to the finishing slag in double-slag arc furnace practice. To react a liquid with a solid, it is axiomatic that the liquid has to wet the solid before anything can happen. If the solid is heavier than the liquid, the problem is easy, but it becomes more difficult when the solid is much lighter than the liquid, as in the case of carbide and liquid iron. Wood recognized this problem and solved it in a unique fashion. The results shown in Table I were obtained by spinning the carbide beneath the surface of the molten iron by means of a refractory centrifuge. This technique allowed each particle of the finely divided carbide to come into intimate contact with the metal and to be wetted thereby. Wood's centrifuge technique was successful in the laboratory where it achieved excellent and consistent results. Some attempts were made to expand this method to commercial practice, but serious difficulty was encountered in obtaining a refractory centrifuge head that would be economically feasible. About this time the war intervened and the project lay dormant for several years. In 1944, it was revived. It was suggested that the carbide could be blown into the metal with a carrier gas in an attempt to eliminate the necessity for the expensive and brittle centrifuge. The idea was first tried out in a fairly large ladle of iron using natural gas as the carrier. Considerable sulphur was removed, but it was quite obvious that the use of natural gas was not practical. Attempts then were made to blow carbide into molten iron using, in turn, nitrogen, argon, carbon dioxide, air, and oxygen. The latter two gases proved unsatisfactory. Calcium evidently prefers oxygen to sulphur because in the tests calcium oxide and carbon dioxide were produced, the sulphur still being untouched in the iron. Nitrogen, argon, and carbon dioxide gave much better results, although the efficiencies and extractions were erratic, and only a few isolated tests approached the results obtained by Wood. Table II shows typical results obtained with these gases. The sulphur removals were interesting, sometimes even encouraging, but it is evident that such erratic behavior could not be tolerated in commercial practice. A number of different types of equipment, such as sand blasting machines, refractory guns, and the like can used to blow the solid into the metal. All types required relatively large quantities of gas in order to maintain the flow of solid carbide through the system and into the metal. It was observed that the bubbles of gas breaking through the surface of the metal contained quantities of unreacted carbide. The liquid metal never came in contact with these particles and if it cannot wet them it cannot react with them. The initial work had shown that carbide had great possibilities as a desulphurizer. In practice

Jan 1, 1952

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker' measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-' sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"' which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963

By P. R. PaeIay, A. Slibar

Using three-dimensional, stress-deformation rate equations for a Bingham plastic, an approximate solution for the laminar flow of drilling mud between the drill pipe and casing is given for the case when the velocity gradients due to axial flow are large compared to velocity gradients due to rotation. INTRODUCTION The fact that drilling mud can be treated, to a first approximation, as a Bingham plastic has been established by several investigators12,3,4,5. A Bingham plastic is a material that is rigid until a certain combination of stresses exceeds a critical value. When the stresses are sufficiently high to initiate flow, the reduced stresses have a constant ratio to the corresponding deformation rates at each point. Prediction of pressure and torque requirements to produce the desired flow of the material have been made by analytical solutions due to Bingham6, Reiner7, and Buckingham8. One part of the present means of calculation that requires clarification is the flow between the drill pipe and casing. Present methods treat the flow resulting from the rotation of the drill pipe separate from the flow produced by the axial pressure gradient. Since the non-linear behavior of a Bingham plastic implies that solutions cannot be superposed, the present analytical investigation was undertaken to obtain a solution to the problem of combined axial and tangential flow. Equations have been proposed for the three-dimensional flow of a Bingham plastic9,10,11 and it has been shown that the proposed equations lead to the usual solutions from the one-dimensional theory". Applying these equations to the flow between two concentric cylinders the problem of axial flow only13 and tangential flow only12 have been solved. In addition to the separate problems of axial and tangential flow between concentric cylinders, the authors have determined the relationship between external torque on the inside cylinder and axial pressure gradient necessary to initiate flow". The solution given in Ref. 14 points out the complexity of the present problem. The problem considered here is the case of simultaneous axial and tangential flow. The axial flow, necessary to keep the drill bit free of removed material, results from the axial pressure gradient. Tangential flow is present since the drill pipe rotates in the hole. The solution given here is valid when the shear stresses in the drilling mud due to rotation are small compared to the shear stresses resulting from the axial flow. This case for laminar flow can be encountered in oilfield drilling. STRESS-DEFORMATION RATE EQUATIONS A detailed derivation of the equations governing the behavior of a Bingham plastic is given in Ref. 10. This section briefly outlines the physical reasoning leading to this three-dimensional formulation of the stress-deforma-tion rate law. Experiments on a certain class of materials have demonstrated the following properties: (1) when a certain combination of the stresses is below a critical value no deformation of the material occurs, (2) to a first approximation this combination of stresses is independent of the hydrostatic pressure (negative average normal stress), (3) if flow occurs the ratio of the reduced stress to the corresponding deformation rate is constant at each point of the flowing material, and (4) incom-pressibility. For the one dimensional case of shear deformation, Bingham6 formulated the governing equation as dxx, = 0 for sxx < to and µdxx = s xx = to for sxx to , . where dxx is the shear deformation rate, sxx the shear stress, to the critical shear stress, and p the slope of the sxx vs dxx curve for dxx > 0. Fig. 1 shows the behavior for pure shear between two parallel plates. Taking into account the physical properties given above and assuming the critical combination of stresses to be measured by the octahedral shear stress, the fol-lowing three-dimensional equations have been proposed.

Jan 1, 1958

By Georges Fleming

The new burden preparation plant of ARBED Luxembourg, Belval- Works, which comprises 2 large sinter strands, is equipped with a process computer connected to a comprehensive process control system. The main jobs done by the computer are the control of the raw mix composition, and thus the monitoring of the stacking of the piles at the bed-blending plant, and the optimization of the sintering process. Among the optimization criteria, quality is considered as the most important. The sinter quality, characterized by the mechanical strength and the state of oxidation, is controlled automatically. The control system which we have dev loped is highly reliable; as a result, the standard deviation of Fe++, for the control of bivalent iron, has been narrowed to 0,5 % and the standard deviation of the IS0 + 6, 3 mm index, for the control of the mechanical strength, has been kept within 1 %. Thanks to these results, the combined savings in fuel consumption at the sinter plant and at the blast furnaces have covered the total costs of the optimization project in 2 years. By applying automatic control, the optimum driving range of the sinter plant has been defined and these new guidelines are used for monitoring the sinter production.

Jan 1, 1977

ENGINEERS AVAILABLE. (Under this heading will be published notes sent to the Secretary of the Institute by members or other persons.) Member, graduate of College of Mines of University of California, with 12 years&apos; operating experience in mining and milling in California, Canada, and Mexico, is open for engagement. Speaks Spanish fluently. No. 17. Mining engineer and metallurgist open for engagement Jan. 1 as superintendent of mines or constructing engineer. Technically educated, with 14 years&apos; experience in United States and Latin America in concentration, amalgamation, cyaniding, constructing. At present building large modern .all-sliming cyanide mill in Central America. No. 18. Member, mining and metallurgical engineer, is open to engagement. Specialty, the treatment of copper ores. Nine years&apos; experience in the operation and also in the design and erection of copper smelteries. Four years true pyrite smelting. Able to organize the administration, accounting, etc., of a large plant. Speaks a fair amount of Spanish, Russian, German, and French. Qualified to take charge of a large smeltery, or to act as assistant to manager of a combined mining and smelting concern. No. 19. Member, technical graduate, 33 years old, 11 years&apos; experience as chemist, metallurgist, and superintendent of lixiviation plant and in charge of construction of cyanide mill, is open for engagement. Speaks Spanish. No. 21. Member, lately with the Bishop Creek Milling Co., California, is now open for engagement as mine superintendent or superintendent of construction of mine and mill structures. No. 25.

Jan 12, 1913

By J. E. Burke

THE origin of recrystallization textures continues to be a matter of controversy. One explanation is that a recrystallization texture occurs because only grains having a limited range of orientations ever appear in the deformed matrix—the oriented nuclea-tion* hypothesis. Another explanation is that grains essentially having all orientations are nucleated but that those having certain orientations grow much more rapidly than any others in the deformation texture, and thus only the rapidly growing grains survive when recrystallization is complete. There has recently appeared a great deal of evidence&apos;- indicate that recrystallized grains of face-centered cubic metals are frequently related to their parent grains by rotations of 20" to 40" about a common [lll] direction. Furthermore, it has been observed that the growth rate of the new grains depends upon their orientations with respect to the matrix, and that the most rapidly growing grains lie within the stated range of orientations. In a recent note, Beck7 has concluded from observations of this type that oriented growth alone is responsible for the appearance of preferred orientations in re-crystallized metals. It should be pointed out. however, that many of the available data indicate that oriented nucleation operates in addition to oriented growth. Thus, while oriented growth may permit a selection to be made among nuclei of several orientations, only a limited number of orientations are available in the first place for such selection.

Jan 1, 1953

By H. R. Crawford, P. B. Crawford, A. F. Tragesser

A method has been developed to calculate wellbore temperatures during mud circulation and the actual cementing operation to aid in the design of cement slurries. The method agrees within 10F with previously measured values. The calculation technique provides temperatures, as functions of time, at varying depths in both the casing and annulus. The technique also provides this information if a relatively cool cement slurry is pumped into the well immediately following circulation of hot mud. Circulating bottom hole temperatures of brine and a bentonite mud were measured. INTRODUCTION As wells are drilled deeper, greater demands are being made on all phases of the industry, and new technology has been developed to provide satisfactory well completions. However, little or no work has been conducted on accurately determining bottom-hole, static and circulating temperatures.. In designing a cement slurry, such factors as density, fluid loss control, viscosity, deterioration from ternperature, compressive strength and pumping time must be considered. Individual well conditions often make it necessary to include still other factors. Pumping time is a primary consideration and, as wells are drilled deeper, encountering higher bottom-hole temperatures, this property becomes even more important. Cement slurries must be designed with sufficient pumping time to provide safe placement in the well; however, the slurry cannot be overly retarded as this will prevent the development of satisfactory compressive strength. The pumping time of a specific cement is currently obtained by subjecting the cement to simulated conditions of temperature and pressure. A reasonably accurate bottom-hole pressure may be obtained by considering hydrostatic heads of fluids, friction pressure and wellhead pressures. However, accurately determining bottom-hole temperatures is much more difficult. Bottom-hole static temperatures are estimated by considering several sources of information, including logging temperatures, published temperature gradient maps and field experience. This information is usually questionable due to disagreement of data from the various sources. Temperature gradient maps were constructed based on temperatures recorded many years ago while running bottom-hole pressure tests. These thermal gradients then represent an average of well conditions and cannot always apply to a specific well. Also, logging temperatures may be affected by the time since fluid was last circulated, rate of penetration, circulating rate and many other factors. Therefore, even though logging temperatures are available, the question still exists as to the correction factor that should be applied to obtain an accurate static temperature. After obtaining static bottom-hole temperature, it is then necessary to relate this to circulating temperatures actually encountered by the cement slurry. This is accomplished by selecting a test schedule from the API RP-10B corresponding to the estimated well conditions.&apos; The API-recommended practice for testing oilwell cement provides testing schedules for various well depths and conditions. These schedules are intended to simulate down-hole conditions during cementing. They provide a rate at which both temperature and pressure are increased until the estimated circulating conditions are reached. These testing schedules represent circulating temperatures for an average well and, although there is flexibility in choosing the test schedule that most accurately simulates the temperature of an individual well, it still is not possible to consider all the well conditions that will affect the bottom-hole temperature. Many factors affect cement temperatures; for example, the length of time a well has remained static prior to running casing and cementing, the circulation time, the temperature of fluids used in cementing, fluid density and flow properties of fluids. The pumping time for a typical retarded cement could vary from 2 to 4 hours with a 10F change in testing temperature. Variations in pumping time are the most critical in highly retarded cements used in deep, hot wells; yet, predicting bottom-hole circulating temperatures is more difficult in these wells. This work was conducted to develop a means of calculating circulating temperatures as a function of well depth, casing and hole size, pumping rate and time, fluid and reservoir physical properties and thermal status of the well. PREVIOUS WORK In 1941 Farris reported on a study to develop information leading to a more practical laboratory evaluation of oilfield cementing mixtures and performance.&apos; It was then recognized that the pressure factor was being neglected,

By Oliver Bowles

DIMENSION stone is a convenient term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, as contrasted with crushed, broken and pulverized stone, discussed in another chapter. Dimension stone includes cut stone, rough building stone, ashlar, rubble, paving blocks, curbing and flagging. Riprap-large, irregular blocks used for shore protection-is classed more properly with crushed and broken stone. COMPOSITION, VARIETIES AND PROPERTIES Stones used as blocks or slabs are of many kinds. The principal varieties are granite, sandstone, limestone and marble. Slate is covered in another chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. Limestone consists essentially of calcium carbonate, with which may be associated certain impurities such as clay, sand, or iron oxide. Dolomites and magnesium limestones used as dimension stone are classed with the high- calcium limestones, as they are used in the same way. Marble is a crystalline form of limestone. Sandstone consists essentially of silica in the form of sand grains cemented together into a coherent mass. Although rock occurrences are numerous and widespread, the ex- acting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced cracks, lines of weakness, or joints can be so used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive color, and freedom from impurities that may cause stains or deterioration usually are required also. Hardness is a variable property. Granites are as hard as or harder than steel while limestones and marbles may be scratched easily with a knife. The hardness of a sandstone depends upon the degree of cementation of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except when stones are subjected to severe abrasion, as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains.

Jan 1, 1949

By Adrian M. Crawford

INTRODUCTION A study has been made of the stability of blocks and wedges of rock subjected to gravity forces in the roofs of underground excavations. Rock wedges may become wholly or partly self supporting with the mobilization of shear resistance of discontinuities bounding such wedges. The influence of in-situ stresses and the relative stiffnesses of the intact rock, and shear and normal stiffnesses of the discontinuities has been investigated. A two dimensional, plane strain model of symmetric rock wegdes in a horizontal stress field has been utilized. A comparison between the results of an extension of a closed form solution proposed by Bray(1981), and numerical analyses with Displacement Discontinuity elements (Crouch, 1976), are presented. These analyses indicate that the stability of the wedge and the stress redistribution around the wedge upon excavation of an opening is markedly influenced by the ratio of intact rock stiffness to seam normal and shear stiffness. It is shown that the analytical solution provides a reasonable measure of the lower and upper bounds of the loads necessary to cause failure of the wedge. MODELS The problem considered (Fig. 1) is a two dimensional plane strain model containing two discontinuities. The discontinuities are symmetrically disposed with respect to a horizontal excavation which forms a wedge of rock bounded by these discontinuities. The angle of the intersecting discontinuities at the apex of the wedge is 2[a]. Mechanical properties of the two discontinuities are identical, being represented by linear normal and shear joint stiffnesses Kn and Ks and angle of friction [o]. The rock wedge is loaded by an in-situ horizontal stress field [ah]

Jan 1, 1982

By John J. Egan

THE present list of problems relating to the physical chemistry of steelmaking has been prepared by the Committee on the Physical Chemistry of Steelmaking, from answers to a questionnaire Submitted to a number of metallurgists engaged in both industrial and educational work throughout the United States. The purpose of the project is to make available to research laboratories a list of problems, all reduced to their simplest terms, the solution of which would aid in creating a better understanding of the steelmaking process. It is not intended to restrict the problems to practical steelmaking. The list also includes the study of the properties, and their correlation, as well as the physical and chemical reactions, of all Substances that occur or that may be in any way associated with steelmaking operations, Such as metallic substances, refractories, nonmetallic inclusions, and the constituents of slags. Many of the problems can be carried out in university or other research laboratories. Others may be most successfully attacked by cooperation of the research men with the operating personnel. It is the Committee&apos;s earnest wish that this cooperation be fostered. It is requested that investigators who are working on any of the problems listed and who anticipate future publication of their results, notify the Secretary of the Committee that such investigation is in progress. Suggested additions to the present list are also requested. The Committee is undertaking to act as a clearing house for information regarding the topics in this field that are being actually studied. Interested persons are invited to correspond with the Secretary. I. Data involved in the state of equilibrium for the various systems (laboratory work, almost entirely). A. SPECIFIC HEATS, HEATS OF FORMATION, ENTROPIES AND FREE ENERGIES OF VARIOUS PURE ELEMENTS OR COMPOUNDS; ALSO CERTAIN TYPICAL SLAGS AND REFRACTORIES. I . Determination of specific heats and entropies of oxides, sulphides, nitrides, etc. over a wide temperature range. 2. Determination of free energies of oxides, sulphides, nitrides, etc. over a wide temperature range. 3. Determination of the heats of formation of the oxides, sulphides, nitrides, etc. 4. Determination of the thermodynamic properties of the more important mineralogical constituents of the basic open-hearth slags such as calcium silicates, calcium phosphates, calcium ferrites, manganese silicates, FeO and Fe2O3. 5. Determination of the specific heats of open-hearth slags, including liquid silicates, if possible.

Jan 1, 1941

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle&apos;s law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world&apos;s sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water