Search Documents

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

Dr. Wadsworth's discussion of leaching is straightforward and certainly points out some of the critical areas in regards to the fundamental aspects of leaching. I will address myself to the more practical aspects of leaching. As a couple of general comments, very fine particles are often dealt with only when necessary. In many processing applications the sands and slimes are separated with the sand portion being treated by common metallurgical techniques and the slime portion being treated essentially by any technology that will recover some of the values. Ore treatment techniques such as leach/precipitate/float (LPF) have been used in the copper industry to take advantage of leachable copper preferentially reporting to the fine fraction. The second advantage, of course, is the improved metallurgy associated with the treatment of the sand fraction. Cases can be made for sand/slime separations in the aluminum and uranium industry where most of the value reports to the slime fraction and the sand fraction is rejected In the agitated leach systems, fine particles are often the most readily attacked and leached. In dump, vat and in-situ leaching, fine particles cause considerable problems. The fines will tend to restrict the solution flow from portions of the leach feed. This either causes a significantly reduced solution flow or, more probably, the solution will channel, by-passing much of the ore. In either case the result is a decreased metal recovery from ore. The fine particles of principal concern are clays of a flat plate-like shape which can very effectively compact, swell and cause a decreased solution flow. Discrete silica grains or sulfide grains due to their shape, even though they may be very fine, will not cause nearly the problems clays and secondary precipitates can cause.

Jan 1, 1979

By V. Apraxine, J. Lakaye, J. J. Saquet, P. Troch

Union Minière du Haut-Katanga owns concessions for extracting copper and associated metals in the high plateau region of Katanga. The concession is about 188 miles long by 44 miles wide and has three principal areas: Southern area-The Prince Leopold mine is an underground operation from which a copper-zinc sulfide ore is extracted. The mine and associated concentrator are at Kipushi. Copper concentrates are smelted and converted to blister copper at the Lubumbashi smelter at Elizabethville.

Jan 12, 1962

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,' we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By N. L. Britton

About two years ago Dr. Newberry referred to me for study a considerable collection of fossil plants sent him by Dr. Arthur F. Wendt, engineer of the silver mines " El Cerro Rico de Potosi" in Bolivia. As I had been interested in working up the extensive accumulations of existing plants made by Dr. H. H. Rusby in the Bolivian Andes further north, and in assisting Dr. Rusby in the study of those now being collected by Mr. Miguel Bang in other parts of that country, I was glad of an opportunity of ascertaining something of the Tertiary flora of the region. I was unable to take up the subject at that time, but have since been able to conclude the investigation, and the results are here presented. At a time when the mineral resources of the Southern States are attracting such widespread interest and attention, I have thought it appropriate to give a short general description of the iron-ore deposits of a territory concerning which little is as yet known and nothing published, so far as I am aware. The data used here are due to the preliminary examinations of the North Carolina Geological Survey, on which work I was engaged during the past summer, and my acknowledgments are due to Prof. J. A. Holmes, State Geologist, and Messrs. Harris, Ashe, and Lewis, of the survey, for their co-operation in the work; also to Messrs. A. S. McCreath and C. B. White for analyses which they Kindly furnished. Other analyses were made by Mr. Charles Baskerville, assistant chemist to the survey, and this may be understood where the name of the chemist is not mentioned. All samples for analysis were dried at 212' F. The accompanying map has been prepared from the revised sheets of the United States Geological Survey by Mr. H. L. Harris, and will be referred to throughout this paper. Ashe county lies in the extreme northwestern part of North Carolina, bordering on Tennessee and Virginia; it is drained principally by the north and south forks of New river and their tributaries, and is therefore on the eastern edge of the great Mississippi drainagebasin. The country is exceedingly rugged and mountainous, having an average elevation of about 2900 feet above sea-level. Jefferson, the county seat, near the center of the county, is 45 miles nearly due south from the Norfolk and Western R.R. at Marion, Va., and 30 miles northwest from the Richmond and Danville R.R. at Wilkesboro, N. C. Geologically the ore-deposits described in this paper are situated in the area of the crystalline rocks, consisting chiefly of gneiss, hornblende-schist, and micaceous schists.

Jan 1, 1893

By Richard McCaffery

THERE has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this. tuyere, the article states, resulted in a decrease of blast pressure of about 4 lb. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various-types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was. furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 lb. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By R. S. McCaffery, D. E. Krause

There has been some discussion among blast-furnace operators regarding the relative merits of tuyeres of the converging type and tuyeres designed in an attempt to produce a diverging jet of air. An article1 on Progress in German Blast Furnace Practice indicates the interest in this subject abroad. This article illustrates a diverging type of tuyere which is shown here in Fig. 1A. The design appears to be rather poor as regards known properties of air flow. The adoption of this tuyere, the arlicle states, resulted in a decrease of blast pressure of about 4 Ib. per sq. in. and an increase of the output of the furnace. If the improvements mentioned are due entirely to the change in tuyere design, the subject of tuyere design seemed worthy of investigation and this paper is a report of such work. Because of the gain in efficiency brought about by the use of a diverging tuyere in the German plant, it was thought desirable to investigate the shape of the air streams issuing from various types of tuyeres to ascertain whether the gain was due to the tuyere itself or to the distribution of the air in the furnace. Since it is difficult to do experimental work on a full-sized furnace, or even on full-sized tuyeres, and because of the equipment available for the work, it was decided to carry out the work on scale models of tuyeres. Therefore, in this work, single tuyeres were used and the blast discharged into the atmosphere. The shape of the air stream was determined by means of a Pitot tube suitably supported in the air stream at various positions. The air was furnished by a Roots blower driven by a 10-hp. direct-current motor having field control, and capable of discharging 250 cu. ft. per min. with a pressure on the discharge of 4 in. of mercury. A modern blast furnace with 21-ft. hearth requires about 50,000 cu. ft. per min. of free air at from 16 to 23 Ib. per sq. in. pressure, depending upon the type of burden. This pressure is the total pressure required to force the air through the burden and through the tuyeres. Upon computation the pressure drop through the tuyeres is about 1 to 2 lb. per sq. in. By making the tuyeres to a one-fifth scale, and by using a pressure of 1.5 in. of mercury, the shape of the air streams should be

Jan 1, 1931

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By Howard Scott, Henry S. Rawdon

The method of demonstrating the structure existing in a metal or alloy at high temperatures, by etching a polished sample after it has been heated to the desired temperature, is quite familiar to metallog-raphists. The usual procedure1 2 is to heat the specimen, previously polished for microscopic examination, to the desired temperature, in a neutral atmosphere (hydrogen or nitrogen), then admit the etching gas (chlorine, hydrochloric acid or similar gas) for a few seconds, and finally, after flushing out the etching gas with the neutral one, cool the specimen in the neutral atmosphere. The pattern produced by etching at a definite temperature is usually taken as a record of the microstructure prevailing at that temperature. It has frequently been pointed out that changes in composition of the surface metal occur during the preliminary heating in the neutral atmosphere, so that the appearance produced by the etching at high temperature may not exactly represent the condition of the interior of the specimen. To overcome this uncertainty, the heating has sometimes been done in vacuo,3 the etching gas being admitted when the desired temperature was reached, then pumped out and the specimen cooled in vacuo. The studies of Rosenhain, Humfrey, and other workers 4, 5, 6, 7, 8 dem-

Jan 1, 1922

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles L range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola 1 described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes2 in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker3 was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle

Jan 1, 1943

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham, Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By W. J. Helfrich, C. L. Sollenberger

Many present direct reduction processes utilize iron ore concentrates for the production of sponge iron and the sponge iron is usually preferred as an agglomerate. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. The present paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. The kinetics of iron oxide reduction have been I studied by numerous investigators1-4 and a rate equation for the hydrogen reduction of hematite and magnetite has been proposed. Mc Kewan' obtained kinetic data for the reduction of hematite spheres sintered at 13'70°C (2498'F'). The kinetics of magnetite reduction was studied by Quets. He compacted the oxide at a pressure of 1 ton per sq cm and sintered the specimens to densities of 95 to 96 pct of theoretical. These studies demonstrated that the reduction of iron oxide is a topochemical process and that the rate of reduction is proportional to the receding surface area of remaining iron oxide. Thus, the measurement of the kinetics of iron oxide reduction depends upon the development of a measurable and well defined interface between metal and reacting oxide. It is evident that the reduction rate will be constant only when the rate of formation of the reaction product layer is constant. It was recognized by Joseph' and Edstrom' that the physical character of the oxide will determine the configuration of the interface between oxide and metal. The reduction of oxides which exhibit few pores or no interconnected pores should proceed by topochemical processes. However, if a massive or dense crystalline ore cracks during the reduction of the oxide, thus allowing the reduction to Proceed away from a well defined oxide/metal interface, then the observed reduction rate will vary or change during reduction. From a process standpoint, it would be difficult to apply absolute reduction rates determined for crystalline or nonporous iron oxide to the direct reduction of a porous pellet of iron ore concentrate. Most present direct reduction processes are attempts to utilize iron ore concentraates in the production of sponge iron. The sponge iron is usually preferred in an agglomerated form for subsequent melting practices. Pelletizing a high grade iron oxide concentrate prior to reduction is a simple approach to the high capacity production of a uniform and agglomerated sponge iron product. One process for preparing such a product has already been de-scribed. This paper describes the effect of different atmospheres and physical characteristics on the reduction of pelletized iron oxide concentrates. ORE CONCENTRATES STUDIED A magnetite concentrate from Reserve Mining Co. and a hematite concentrate from U.S. Steel Corp. were used in preparing pellets for these experiments. A head analysis of these concentrates is given in Table I. To compare the reduction rates of pelletized concentrates, it was necessary that each pellet contain equal amounts of oxygen which could be removed by reduction, regardless of the oxidation state, i.e., Fez% or Fe304. Also, because of the difficulty in preparing spherical pellets of uniform size, weight, density, and porosity for experimental purposes, pellets of a cylindrical shape were formed in a press.

Jan 1, 1961

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes' in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of station¬ary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker' was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It 'could handle

Jan 1, 1943

By Denis Yeung, B. H. G. Brady

A hybrid finite element-boundary element code with eight noded isoparametric finite elements and three noded boundary elements is described for plane strain and linear isotropic elasticity. In the direct formulation of the Boundary Flement Method, quadratic variation of geometry and displacements, and linear variation of tractions with respect to the element intrinsic coordinates are used. The boundary element region is treated as a "super-element" in the finite element sense.

Jan 1, 1982

By Harold L. Bare, Frank R. Barnako

Coal mining historically has been a. hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work. COAL MINE ACCIDENT EXPERIENCE The US Mine Safety and Health Administration (MSHA) is the main source for accident experience data in coal mines. Coal mine operators are required, by law, to forward to MSHA monthly the number of fatal and disabling injuries, man-hours worked, and tons of coal mined. This information is compiled and published quarterly, with annual summaries, by MSHA. Trends in the number of fatalities and fatal injury rates are shown in Fig. 1. Major coal mine disasters, with number of miners killed, and dates of coal mine safety legislation are shown in Table 1. The fatal and disabling injury frequency rates for the coal industry are shown in Fig. 2.

Jan 1, 1981

By Harold L. Bare, Frank R. Barnako

Coal mining historically has been a hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work. COAL MINE ACCIDENT EXPERIENCE The US Mine Safety and Health Administration (MSHA) is the main source for accident experience data in coal mines. Coal mine operators are required, by law, to forward to MSHA monthly the number of fatal and disabling injuries, man-hours worked, and tons of coal mined. This information is compiled and published quarterly, with annual summaries, by MSHA. Trends in the number of fatalities and fatal injury rates are shown in Fig. 1. Major coal mine disasters, with number of miners killed, and dates of coal mine safety legislation are shown in Table 1. The fatal and disabling injury frequency rates for the coal industry are shown in Fig. 2.

Jan 1, 1981

By Carl D. Broadbent

In 1956, Kennecott Copper Corp. instituted a slope mechanics program. Its objective was to obtain effi-ient and safe pit slopes. Since then, Kennecott has onducted a great deal of research into the area, most otably at the Kimbley Pit. This paper, which describes the transitional work at this period and draws from the pertinent experimental work done by others, paves the way for the next step of the program: refining the design process and applying it for profit. The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes, the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956, Kennecott instituted a program to provide

Jan 1, 1970

By E. P. Valby

A method is presented in which the hydrocarbon weight fractional analyses of the well effluents from a true gas-tip-portion well and a true dark-oil-ring well furnish the basic data for determining the properties of any mixture of production from the two sources. The effect of injected gas on these properties can be computed. Comparison of similar properties of a given well effluent to the properties of mixtures of the basic well effluents will give the relative amounts of production from the two sources and injected gas. Presentation of Problem Oil fields having an area of gas-cap, or light-oil production, over the dark-oil area present a problem of increasing gas-oil ratios during the production of an oil well. The use of pressure maintenance in a field such as above, or a cycling project, wherein residue gas from an absorption plant is injected into the reservoir, adds to the problem, because a part of the increased gas-oil ratio may be due to the production of injected gas. The usefulness of a means to determine the amount of injected gas in a well effluent led to the development of a method in which well-effluent analyses of a true gas-cap-portion well and a true dark-oil-ring well furnish the basic data needed to determine whether injected gas of a known composition is present in a given well effluent. Development op Method The method presented herein is based upon the principle that if two fluids, or well effluents, having different properties are mixed in known proportions by weight, • the properties of their mixtures can be computed. Conversely, if these basic data are known, the properties of a mixed well effauent can be used to compute the relative amounts of each type of well effluent in the mixture. A convenient way of making these computations is to have the fractional analyses of the base well effluents and mixtures expressed in weight fractions The mathematical equations expressing the properties of mixtures will be developed for a two-component system consisting of the well effluents from the dark-oil ring and the gas-cap area. The added effect of injected gas, a third component, will also be developed. The following assumptions have been made in developing the method: 1. The gas-cap and dark-oil fluids exist initially in separate portions of the reservoir. 2. The fluids in each portion exist in a single phase at pressures above the saturation pressure for the dark-oil fluid. 3. The composition of each fluid is substantially constant throughout its respective portion of the reservoir. 4. Changes in reservoir pressure and temperature will not change the composition of the fluid entering the well bore. 5. The injected gas displaces original gas-cap fluid 100 per cent. •• 6. AS the injected gas travels through a

Jan 1, 1945

By W. A. Mudge, Paul D. Merica

One of the most prominent features of our present-day industrial development is the ever-increasing demand put upon materials of construction. Engineering ingenuity, within the past 25 years, has been unusually active, and in some fields at least engineers frankly say that engineering design has progressed as far as the limitations imposed by the properties of the present materials of construction will permit. Consequently, they are today demanding improvement in their working materials and seeking new ones, through the aid of which the present limitations of design may be overcome. The activity of this search is evident in all fields, but it is particularly so in that of structural materials required to be resistant to corrosion. The corrosion resistance of metals and alloys is never absolute and all-inclusive; a particular alloy will withstand some corrosive conditions well and fail utterly under others. Furthermore, other properties, physical and mechanical, required in conjunction with corrosion resistance vary considerably for different commercial applications. One wants a soft, ductile sheet metal resistant to atmospheric corrosion; another, a high-strength alloy resistant to sulfuric acid. The last decade has witnessed active and definite progress in the development of high-strength, corrosion-resisting alloys. In June, 1924, a symposium by the American Society for Testing Materials, on Corrosion-resistant, Heat-resistant and Electrical-resistance Alloys, disclosed no less than 60 commercial alloys the properties of which were described as being suitable for industrial service where corrosion resistance was a feature. Today the number of these alloys has been doubled, at least. In addition, economy in design and construction through decreased weight has given considerable impetus to the improvement of alloys of which the mechanical propprties may be improved by heat-treatment.

Jan 1, 1935