Search Documents

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By C. R. Fast, George C. Howard

Laboratory and field testing of various squeeze cementing techniques and materials revealed that many improvements could be made in squeeze cementing operations. The use of a slow-pumping squeeze cementing procedure permitted the control of the quantity of cement displaced into a formation and aided in obtaining a high final squeeze pressure. Field testing indicated the desirability of obtaining high final squeeze pressures, the need for improved formation breakdown fluids, and the necessity of controlling the pressure differential during testing after a squeeze job. INTRODUCTION During the past few years, squeeze cementing operations have been investigated, both from the theoretical as well as the practical point of view, in an effort to arrive at some solution to the many and varied problems that arise with this type of operation. A review of well files indicated that in many instances, wells were being squeeze cemented four and five times before a satisfactory pressure buildup was obtained. There seemed to be considerable variation in opinion as to the proper method of squeeze cementing, as well as disagreement as to the proper breakdown agent, the quantity of cement that should be used, type retainer and length of WOC* time that was necessary. Consequently, it was deemed advisable to approach this problem theoretically, field testing each idea developed in hopes of eventually arriving at a squeeze cementing procedure that would give reasonable assurance of a successful job after one squeeze cementing operation. This investigation was. therefore, divided into two broad headings: (1) Preliminary studies, which include both theoretical and laboratory studies, and (2) Field investigations to determine the proper squeeze cementing methods. PRELIMINARY STUDIES Overburden Pressure Studies Squeeze cementing problems are so intimately related to the earth's overburden pressure that solutions to them are very difficult, if not impossible, without an understanding of the nature and magnitude of the overburden pressures encountered at the depths of producing wells. It was thus felt that the first approach to research on squeeze cementing should be made through a study of these pressures. Since there has been rather loose usage of a number of the terms related to overburden preasure by different writers, the terms to be subsequently used are defined here. Theoretical overburden pressure is the calculated pressure at any given depth exerted by the theoretical weight of overlying formations as calculated from the average rock density. Fluid displacement pressure is that pressure at which fluid can be injected into a formation after it has been broken down. It may be more or less than the theoretical overburden pressure. Formation breakdown pressure is that pressure at which a formation parts or breaks and is usually thought of as fluid displacement pressure plus rock strength. Breakdown agent is that fluid with which the formation is fractured. The first step in the study of the earth's overburden pressures involved a review of pertinent technical literature. The general opinion expressed was that the overburden pressure gradient of the earth's formations is roughly 1.0 psi per foot of depth, and that application of sufficient pressure to stratified formations. will cause them to part at or parallel to the bedding planes. The second step in the study of overburden pressures involved a study of available well data in an effort to obtain some definite information as to the actual values experienced in the field for the above mentioned terms. Data from 115 cement squeeze jobs in the Gulf Coast area and 46 cement squeeze jobs and acid jobs in the West Texas-New Mexico area were closely analyzed. The analysis of these data showed that the average formation breakdown

Jan 1, 1950

By J. L. Jones

1. Brinell tests at progressively increasing temperatures are given for a representative lead-base and a representative tin-base babbitt, showing that the former has superior resistance to deformation at the working temperatures of bearings. 2. Small squares of bearing bronze, tinned and then babbitted with a representative lead-base babbitt and a representative tin-base babbitt were subjected to compressive loading. The lead-base babbitt showed less average compression than the tin-base babbitt. Compression did not materially increase the Brinell hardness of the babbitts. 3. A process and a tool are described for giving smoother and more accurate surfaces to bearings than has heretofore been possible. The following experiments have recently been carried out in the chemical laboratory of the Westinghouse Electric and Manufacturing Co., Pittsburgh, Pa. While the work is incomplete, it is described at the present time because data on the comparative merits of lead-base and tin-base babbitts are of interest in connection with the present shortage of tin. BRinell Habdness of Babbitt at Increasing Temperatures Bearings fail because of wiping, or deformation. Hence tenacity is desirable in a bearing metal, especially tenacity at high temperatures. The Brinell test is commonly regarded as a measure of tenacity. In fact, it has recently been proposed to substitute for Brinell hardness number the expression " tenacity number."l It seemed, therefore, that the Brinell test was especially adapted for the tests described. Disks, 4 in. (101 mm.) in diameter and 1.5 in. (38 mm.) thick, were made of the babbitts to be studied, designated A, B, C. They were poured into metal molds, pyrometer leads being soldered in the center of each disk. The composition of the babbitts was as follows:

Jan 1, 1919

By Petter Östberg

Having brought with me to this meeting a couple of "Mitis'' wrought-iron castings, I have found that they attracted a great deal of attention from steel manufacturers, and especially from those experienced in making castings, among whom some have said that they felt inclined to "unhesitatingly dcclare their manufacture an impossibility," if they had not seen the samples. The consequent demand for explanation of the method of manufacture has been SO great that I accept with pleasure the request by the President to address the meeting on the subject. My object in this address shall be only to explain the main features of the manufacture, referring those who take more interest in the matter to Mr. Th. Nordenfelt's paper, read before the British Iron and Steel Institute, reprinted in many American papers, and containing both a historical sketch of the inventions and many interesting details. As the manufacture of castings from steel by others is, at least to some extent, a success, I shall, in my explanations hereafter, refer to wronght-iron, although our mode of manufacture is equally applicable, with corresponding advantage, to steel of any temper. The successful manufacture of castings depends upon several very important matters, besides the necessary skill of the workman. You must have a suitable metal as raw material; you must have an eacient and suitable furnace for smelting, so as not to injure the metal; you must be able to handle the metal in a suitable way, from the time it is ready in the furnace until it is poured into the moulds; you must have a suitable moulding material. I claim that in every one of these different branches we have made great

Jan 1, 1886

By C.P. Proctor, J. T. Crawford, J.A. Younkins

Coal-cleaning plants using the launder process generally wash the fine coal (minus ? or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enter the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immediately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions. OpeRating Equipment The washing units considered here are part of a complete plant cleaning minus 4-in. coal. The primary cleaned product is a high-quality gas and metallurgical coal and another portion of the output may be shipped as a steam coal. The units consist of two parallel Rheolaveur free-discharge units each containing five launders, together with three 7 by 14-ft. Plato tables. The launders are designated by the letters A-B-C-D-E (Fig. I), launder A being the top and longest; E being the bottom and shortest. Launder details are given in Table 1. The launders are equipped with a series of free-discharge Rheolaveur boxes, which are integral parts of the launder (Figs. 2 and 3). Each box with-

Jan 1, 1940

By C. P. Proctor, J. A. Younkins, J. T. Crawford

Coal-cleaning plants using the launder process generally wash the fine coal (minus ? or minus 5/16-in.) separately in a plant consisting of washing launders or troughs placed one below another and sometimes supplemented by additional washing equipment such as tables and jigs. The coal and its associated impurities enter the feed end of the top launder, with a current of push water. As the material moves along the impurities, being heavier than coal, settle toward the bottom of the launder and are drawn off, with some coal, through "free discharge" boxes to the launder below. These boxes were given their name because their discharge falls freely; that is, it does not discharge into a water seal. Thus the impurities are progressively concentrated in the lower launders until box products are sufficiently free of coal to be discharged to refuse. The overflows of the upper launders go to clean coal while the overflow of the lowest launder, and perhaps that of the one immediately above, is usually recirculated to the plant feed. Thus the bulk of the clean coal is removed rapidly and the impurities are concentrated more slowly. The chief purpose of this paper is to present the cleaning data of such a plant under different operating conditions. OpeRating Equipment The washing units considered here are part of a complete plant cleaning minus 4-in. coal. The primary cleaned product is a high-quality gas and metallurgical coal and another portion of the output may be shipped as a steam coal. The units consist of two parallel Rheolaveur free-discharge units each containing five launders, together with three 7 by 14-ft. Plato tables. The launders are designated by the letters A-B-C-D-E (Fig. I), launder A being the top and longest; E being the bottom and shortest. Launder details are given in Table 1. The launders are equipped with a series of free-discharge Rheolaveur boxes, which are integral parts of the launder (Figs. 2 and 3). Each box with-

Jan 1, 1940

By W. C. Leslie, R. M. Fisher, K. G. Carroll

A nitride, believed to be Si3N, has been separated from three nitrided silicon steels. Germanium nitride, Ge3N4, has been prepared from pure germanium. Comparison of the diffraction patterns indicates that the two nitrides are isomorphous; on orthorhombic structure is suggested in place of the rhombohedral structure previously reported for Ge3N4. THE possibility that a nitride of silicon may, under appropriate conditions, precipitate in silicon steels or in steels killed with silicon makes it desirable to have some positive means of identifying such a compound. One such means is the X-ray or electron diffraction pattern of the nitride. A review of the meager data in the literature indicates that the nitride most likely to form is Si3N4, a conclusion supported by the results of a study of nitrided silicon steels to be published shortly by L. S. Darken and R. P. Smith, of this Laboratory. Unfortunately, there is available no diffraction pattern for this nitride. Data have been reported, however, for Ge3N4 which, judging from the similarity between germanium and silicon, might be expected to be isomorphous with Si3N4. An effort was made, therefore, to form such a silicon nitride, to determine its composition and diffraction pattern and, if possible, its structure. To this end a series of three silicon steels was nitrided under controlled conditions with the resultant formation of nitride particles which yielded an electron diffraction pattern in situ. The particles were then extracted from the steel and an attempt was made to determine their chemical composition. X-ray and electron diffraction patterns were also obtained from the extracted particles, which indicate that the nitride is isomorphous with Ge3N4, although a complete determination of the structure has not been possible. These results show that a silicon nitride with a well-defined diffraction pattern can form in silicon steels, and they suggest that this nitride is Si3N4. Materials and Procedures The sillicon steels investigated were In the form of thin sheet or strip and had the composition shown in Table I. The 0.58 and 1.21 pct Si steels were nitrided by holding them at 1110°F in an H2-NH3 atmosphere containing 3 pct ammonia for 48 hr. The nitride particle size was increased by subsequent heating at 1500°F for 13 1/2 hr in helium. The resulting microstructure is shown in Fig. 1. The steel containing 3.20 pct Si was nitrided at 1200°F for 16 1/2 hr after which it was held in helium at 1500°F for 4 hr. Its structure as seen under the electron microscope is illustrated by Fig. 2. As would be expected from the higher silicon content and the shorter holding time at 1500 °F, the nitride particles are smaller and more numerous than those in the 1.21 pct Si steel. The ammonia-hydrogen treatment reduced the carbon content of the steels to a very low level, so no interference was encountered from carbon or carbides. In the case of the 3.2 pct Si steel, the carbon was reduced to 0.003 pct before nitriding by heating in dry hydrogen. Attempts to obtain an X-ray diffraction pattern from polished and etched surfaces of the 1.21 and the 3.20 pct Si steels were unsuccessful. However, an electron diffraction pattern was obtained from the surface of the steels. The interplanar spacings obtained from these patterns arc shown in Table 11, col. 5. The nitride particles were then extracted from all three steels by dissolving the ferrite matrix in bromine-methyl acetate, the solution used in the Beeghly method for the extraction of aluminum nitride from steel. X-ray diffraction patterns of these residues, obtained by means of a spectrometer and by a 57 mm Debye-Scherrer powder camera using filtered cobalt or chromium radiation, are given in Table II along with the pattern obtained by

Jan 1, 1953

By Albert R. Ledoux

I am indebted to The Kaolin Co. of West Cornwall, Conn., and particularly to its engineer, Mr. M. Wanner, for permission to make public, through the Transactions of the American Institute of Mining Engineers, the interesting results of his experiments, having in view the winning of kaolin from deep deposits without shaft-sinking or removing of the overburden. So far as I am aware, nothing like it has been accomplished heretofore, although it reminds one of the methods successfully employed in Louisiana for the winning of sulphur from deep beds by the sinking of pipes one within another, injecting superheated steam under pressure through one pipe, the heat of the steam liquefying the sulphur and the pressure forcing it up through the other pipe to bins at the surface. The kaolin-deposit at West Cornwall is an alteration in situ— that is, it is not sedimentary. A series of clay-veins, dipping about 50" from the vertical, lie between a foot-wall of' limonite and a hanging-wall of gneiss and hornblende schist. The clay-veins alternate with veins or seams of more or less broken quartz, and unaltered feldspar. The deposit, which occurs at a point about 600 ft. above the Housatonic river, was opened five years ago, and about 5,000 tons of a superior grade of washed kaolin have been extracted from open pits, and sold. It soon became evident that this mode of extracting the product would prove unremunerative, by reason of the dip of the vein and the intercalary strata and lenses of quartz, and a more satisfactory method of working the deposit was sought. It is well understood that, in the preparation of all clays for market, especially residuary kaolin, the most important as well as the most difficult step is the washing of the crude product. The dificulties increaee with the percentage of foreign matter, especially quartz and mica, contained in the product. Hence, a system

Jan 1, 1907

By J. B. Dilworth

In estimating the investment-value of a mining-property or plant, the value of which decreases with operation, it is often necessary to know the sum which must be set aside periodically from earnings either to renew the plant at the end of its life, or to return the capital involved when the earningpower of the investment has ceased. In such cases it is manifestly incorrect simply to divide the total amount to be retired by the 'number of periods (usually years) during which the investment shall be active, as the sums periodically withdrawn have a certain interest-earning power varying with the length of time they are held and with the opportunities afforded for their investment. But though the interest may be considered to accumulate regularly year by year, yet the rules and tables for compouiid interest do not apply, owing to the addition of a fixed amount of new money to the total at the beginning of each period. Briefly stated, the problem of sinking-funds is, to find the amount of money which must be periodically set aside at a certain rate of interest, regularly compounded, to yield a certain sum in a given length of time. In most practical cases the interest is compounded and the fresh amount added at the same time—usually once a year—and on this basis the problem may be solved as follows : Let S = total amount to be retired, Let T = interest rate : R = 1 + r, Let n = life of tlie sinking-fund or the amortization-period, Let L = the sum set aside at the end of each year. Then the amouilt of the sinking-fund at the end of first year is 2, which at the end of n years will have illcreased by compound interest to IRn-l. Similarly, another amount, x, will be set aside at the end of second year, which will in turn increase

Jan 1, 1911

By P. M. Kelly

TWO analytical methods for calculating the positions of matrix and twin reflections on electron-diffraction patterns of a twinned cubic crystal have recently been published.1,2 Meieran and Richman1 considered the case of twinning on (1 12) in a bcc structure, while a more general treatment, capable of analyzing twinning on any plane in a cubic crystal, was developed by Johari and Thomas.2 The latter authors applied their general rotation matrix to both (111) twinning in face-centered crystals and {112} twinning in body-centered crystals and they derived separate expressions for these two cases. This separate treatment masks the fact that in a holosymmetric cubic crystal a (111) twin is crys-tallographically equivalent to a {112} twin.3 This is analogous to the crystallographic equivalence of rotation and reflection twins in centrosymmetric crys tals. A particularly simple example of this equivalence occurs when the two twin planes are perpendicular to each other—for example (111) and (112). Then, if twinning on (111) moves a point P to a new position P1, and twinning on (112) moves P to P2, P1 and P2 will be related to each other by a 180-deg rotation about [110]— the direction normal to both (111) and (112). Since there are diad axis axis along (110) direction in a holosymmetric cubic crys tal the two positions P1 and P2 must be crystallo-graphically equivalent. In other words if a particular pole (hk l) is in a position P1 after twinning on (Ill), then after twinning on (112) a pole of the type {hkl}—but not the particular pole (hk1)—will also be in the position P1. As a result, when only the general (as opposed to the particular) indices of poles after twinning are required, twinning on (111) gives the same results as twinning on (112). To convert the results for a (111) twin to those applicable to a (112) twin, when the particular (as opposed to the general) indices of poles after twinning are required, all that is necessary is to multiply the indices of the twin poles by the matrix for 180-deg rotation about [lie], i.e., The analytical methods suffer the disadvantage that a new set of calculations must be performed for each different diffraction pattern or, as is done in the Meieran and Richman treatment,1 a lengthy list of the location of the twin spots in reciprocal space must be prepared. All the tedious computation involved in these analytical approaches can be avoided by simply plotting, on tracing paper, a stereographic projection of a crystal twinned on say (112). By superimposing this twin stereogram on a standard (001) projection (preferably with the points and indices in a different color from those on the twin stereogram) the relative positions of both matrix and twin reflections can be determined by inspection. Alternatively, a composite projection can be

Jan 1, 1965

By P. D. Zemany, G. W. Sear, B. W. Roberts

Vanadium metal is embrittled by hydrogen at a temperature as low as 250°C when held in the presence of manganese metal and water vapor in a rough vacuum. It is established that the property changes are caused by the catalytic decomposition of water vapor at the vanadium surface and the diffusion into and solution in the vanadium of the resultant hydrogen. It is found that manganese is a necessary component of the catalyst. The manganese is transported in the vapor phase by an unknown molecule. A deuterium tracer experiment demonstates the role of water vapor in the embrittle-ment process. VANADIUM metal foils were observed to become embrittled' at a temperature of about 300 °C when held in the presence of manganese metal and a small amount of moist air, This paper describes the investigation to find the embrittling agent and an understanding of the relatively low temperature reactions that are involved. Experimental The vanadium metal foil used was prepared by cold-rolling and pack-rolling 32 mil sheet" in a series of steps down to 1 mil foil. The original observation was confirmed by sealing vanadium foils of 3 x 10 sq cm into individual Pyrex tubes with manganese powder† and a con- trol tube containing only the vanadium foil. These tubes were evacuated to 10 -5 mm Hg without baking and sealed. After heat treatment for 200 hr at 300°C, the control foil showed no change in duetility, whereas the foil contained in the manganese— containing tube was embrittled. The visual appearance of each was unchanged. A series of Pyrex sample tubes, about 2.5 cm diam and 25 cm long, were prepared, each containing a 3 x 10 sq cm piece of foil and 5 g manganese powder at the lower end of the tube. By reducing the time of anneal and the temperature of these samples, it was found that embrittlement could be created at 250°C in a time as short as 1 hr. Since the vanadium metal used here has been drastically cold-worked by rolling, it is assumed that it contains a maximum number of dislocations. To check the possible necessity of dislocations in this low temperature reaction, a vanadium foil sample was annealed in Vycor for 2 hr at 800°C to re crystallize and reduce the dislocation concentration. Metallographic examination showed grains which were not visible before annealing. The embrittlement procedure was carried out at 300°C and 3 hr. Upon checking the foil no embrittlement was observed. Further experiments demonstrated that about 6 hr at 300°C are required to create embrittlement in the foil. This delay in the onset of embrittlement in the vanadium foil suggests but does not prove that dislocation channels play a role in the embrittlement phenomena. If manganese metal is necessary for this low temperature embrittlement, do other elements in the transition metals group yield the same result? To check this qualitatively, a group of elements of similar atomic radii were obtained and sealed as before into Pyrex tubes with a sheet of vanadium foil. These tubes were annealed at 250°C for 6 hr and included (with radii)-2 A1 (1.4A), As (1.25A), Be (1.2A), Co (1.25A), Cr (1.45A), Cu (1.25A), Fe (1.25A), Ga (1.2A), Ge (1.25L%), Mn (1.3A), Ni (1.25A), Si (1.2A), Ti (1.45A), Zn (1.3A), air, H,O, 10 cm Hg of dry hydrogen, and MnO, powder. Upon testing the above sample foils for brittleness, only the manganese-containing tube yielded a brittle foil. Manganese Transport—To eliminate contact of manganese metal powder and vanadium foil, sample tubes were prepared with fritted glass barriers. The embrittlement reaction was still found to occur. Thus, the mode of transfer of manganese is certainly vapor transport. A vanadium foil was embrittled by this mechanism in an evacuated Pyrex tube for 8 hr at 300°C. By means of X-ray fluorescence analysis,' the amount of manganese added to the surface was established at 5 ±2 x 10 -6 g per sq cm. Since the average rate of manganese deposition is known, an effective average pressure of an assumed carrier compound can be computed. ___ P = M/T v2p mkT

Jan 1, 1959

By C. Bezemer, I. Havenaar

An investigation was carried out on the dynamic liltration behavior of drilling fluids. In a set-up consisting of a porous pipe through which the drilling mud was circulated, dynamic liltration rates and cake thicknesses were determined as a function of flow rate and filtration time. Eventually, a state of equilibrium was reached; i.e., both cake thickness and filtration rate attained constant values. Concurrently, dynamic filtration tests were carried out in a simple dynamic filter apparatus where mud flow was similar to that in a rotational vismmeter. In both arrangements the relation between equilibrium liltration data and rate of shear at the cake surlace was studied. Filter pipe and dynamic filter apparatus were lound to give identical relations. It was therelore concluded that the latter apparatus, which is suitable lor routine measurements on small amounts of mud, could be used to determine the dynamic liltration behavior of mud under borehole flow conditions. Some data are presented on the effect of filtration pressure and temperature on equilibrium filtration rate and cake thickness. INTRODUCTION In oil well drilling, the drilling fluid used generally forms a mud cake on the permeable sections of the borehole wall while filtrate is lost into the formation. As to the conditions under which this filtration process takes place, a distinction should be made between static mud filtration (mud is not circulating) and dynamic mud filtration (mud is circulating). In recent years several investigatorsl-5 have studied the process of dynamic mud filtration about which little had previously been known. This type of filtration is the subject of this paper which confirms several findings of previous investigators. It differs from already published works, however, in the following respects. 1. It contains a description of a simple laboratory apparatus developed for dynamic filtration measurements on small amounts of mud. 2. The effect of rate of shear at the cake surface on dynamic filtration has been studied. As a result of this study, dynamic filtration data pertaining to the borehole conditions of mud flow can be found from laboratory tests. 3. Some data are presented on the effect of filtration pressure and temperature on dynamic filtration. The work was limited to a small number of muds. No attempt was made to compare data on API filtrare loss with dynamic filtration rates. Previous workers have clearly shown that no correlation exists between static and dynamic filtration rates. EXPERIMENTAL ARRANGEMENT To establish whether the effect of mud flow conditions on dynamic filtrations is governed by the rate of shear at the cake surface, two different types of mud flow were used. In this connection the experiments were partially conducted by means of a porous pipe through which mud was circulated, partly in a dynamic filter apparatus which somewhat resembles a rotational viscometer. In both cases the flow conditions of the mud were well defined, thus making it possible to-calculate rates of shear at the cake surface. The filter pipe was 200 cm long with an internal diameter of 3 cm. Its perforated wall was covered on the inside with filter cloth on which the mud cake could form. Mud was pumped through the pipe at linear rates varying from 20 to 186 cm/sec. The required filtration pressure was obtained by means of a lack-pressure valve downstream of the filter pipe. In this arrangement the type of flow existing in the borehole is reasonably well simulated. The dynamic filter apparatus (Figs. I. and 2) consists mainly of two concentric cylinders with a clearance of about 0.5 cm. The outer cylinder (rotor) can be rotated at rates up to 1,000 rpm. The outer surface of the inner cylinder (radius about 2.5 cm) is covered with filter cloth or paper supported by copper gauze. The two cylinders are mounted inside a pressure

Jan 1, 1967

By William E. Ford, Edward Salisbury Dana

I. Oxides of Silicon. 11. Oxides of the Semi-Metals : Tellurium, Arsenic, Antimony, Bismuth ; also Molybdenum, Tungsten. III. Oxides of the Metals. The Fifth Class, that of the OXIDES, is subdivided into three sections, according to the positive element present. The oxides of the non-metal silicon are placed by themselves, but it will be noted that the compounds of the related element titanium are included with those of the metals proper. This last is made necessary by the fact that in one of its forms TiOz is isomorphous with MnOp and PbOz. A series of oxygen compounds which are properly to be viewed as salts, e.g., the species of the Spinel Group and a few others, are for convenience also included in this class.

Jan 1, 1922

By Allen Johnson

WITH a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Labo-ratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. STOKERS INVESTIGATED One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-Stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.-The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plungers, or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal. through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the ,general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1935

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Allen J. Johnson

With a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Laboratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. Stokees Investigated One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.—The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plunger1 or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1936

By Gordon H. Chambers

MANGANESE ore is a true jack-of-all trades among industrial minerals, its only possible rival being iron ore. It is used in porcelain enamel, dry batteries, building brick, glazed pottery, floor tile, plastics, welding rods, chemicals, and varnish. You may be reading this through spectacles decolorized with manganese, and the light bulb above you contains some of this element. GEOLOGY Nearly all commercial manganese oxide deposits are of secondary origin; that is, they are concentrated by weathering from other manganese minerals more sparsely distributed in veins. The oxide minerals usually form irregular masses but in some places (Russia) they occur as beds of varying thickness and purity. Some manganese oxide bodies occur in soft gravel or clay formations but in other places the minerals are found in the form of veins and rounded nodules in limestone and other hard rocks. The geologic features of manganese deposits closely resemble those of iron deposits. Classification of the deposits is shown in the following table: I. Classification of manganese deposits based upon form of occurrence A. Stratiform masses 1. Oxides interlayered with sediments or layered volcanic or metamorphic rocks 2. Carbonates or silicates interlayered with sediments or layered volcanic or metamorphic rocks 3. Oxides, as surface bog deposits B. Veins and breccia filling 1. Oxides in larger part 2. Carbonates or silicates partly weathered to oxides C. Irregular masses 1. Oxides 2. Carbonates or silicates largely weathered to oxides D. Aggregates of small oxides in clay or weathered rocks 1. Mainly oxides E. Unclassified deposits II Classification of manganese deposits based upon mode of origin A. Hydrothermal deposits

Jan 1, 1949

By D. B. Smith, John Chipman

THIS investigation was undertaken as a prerequisite to the study of sulphur activities in the liquid system Fe-Cu-Ni, a continuation of the work of Sherman, Elvander, and Chipman,¹ using the same equipment and the same experimental technique. Temperature measurements are made with a disappearing filament optical pyrometer, sighting through a prism onto the surface of the melt which is heated by induction. To obtain true temperatures by this means, a calibration is necessary, since, in the absence of true black-body conditions, the observed temperature is always lower than the true temperature. This calibration is actually an emissivity correction, since the emissivity is a function of both temperature and melt composition. The original furnace was used with a deeper metal bath to provide sufficient depth of immersion for the thermocouple which was inserted through the sampling hole. The atmosphere was a 50-50 mixture or argon and hydrogen passing through the furnace at a rate of 1000 ml per min, and preheated by means of a molybdenum resistance coil. It was assumed that the rapid gas flow effectively eliminated any error which might have resulted from the presence of metallic vapor. The charge in each case consisted of about 300 g of metal, contained in a high purity, dense alumina crucible. At each melt composition, readings of the optical pyrometer and of a thermocouple immersed in the molten metal were taken simultaneously. Calibration curves of optical vs. true temperature were then made for each melt composition investigated. Thermocouples were made of 0.010 in. platinum and platinum-10 pct rhodium. They were checked against the melting point of chemically pure copper. Silica protection tubes with an outer diameter of approximately 1/8 in. were used. The depth of immersion of the tip in the molten metal was approximately 1 14 in. The life of these small thermocouples was relatively short, varying from approximately 1 min at 1550°C to 10 min or longer at 1300°C. Melts containing iron corroded the protection tubes more than those without iron present. Measurements taken while heating checked those taken while cooling, indicating the absence of a temperature gradient between the molten metal and the thermocouple. Results The temperature range of the. measurements on copper-free metals extended from the melting point to 1600°C. For copper the upper limit was 1380°C, and the data were extrapolated linearly for comparison with observations on the other metals and alloys at 1535°C. Examples of typical calibration curves for various melt compositions are shown in Fig. 1. These curves, besides providing a calibration system for the given experimental conditions, also give a basis for the calculation of true emissivities at the effective wavelength of the pyrometer, 0.65 micron. The starting point of the calculations is the value of the emissivity of iron at its melting point. Taking the melting point of electrolytic iron under hydrogen as 1535°C, and using the corresponding emissivity value of 0.43, as determined by Dastur and Gokcen,² the emissivities can be determined as functions of composition (and temperature, if desired). The relationship used is the Wien equation: ln(Ea)=C2/?(1/T1-1/Ta where E is the emissivity; a, the transmissivity of the optical system; C,, the fundamental constant, 14,380 micron-degrees; A, the wave length of light used (0.65 micron); Tt, the true temperature, OK; and T., the apparent temperature, OK. At the melting point of iron the observed temperature was 1358"; this gives 0.62 for the transmissivity, which compares with 0.65 in the similar system used by Dastur and Gokcen. The emissivities of all the compositions investigated were determined at 1535°C, after obtaining from each calibration curve the corresponding temperature. These results

Jan 1, 1953

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By R. R. Hartman, W. B. Agocs

IN the course of a return flight from Olympia, Wash., to Laramie, Wyo., an airborne magnetometer profile was recorded continuously. The level of flight was controlled at barometric levels along segments of the flight. Barometric altitude was changed from 3000 ft to a maximum of 12,000 ft above mean sea level to take care of topographic variations. Terrain clearance varied from 800 to 7300 ft. Horizontal positions were obtained by recording and tying to cities, towns, airports, river crossings, and other landmarks in the course of the flight. Figs. 1-6 show the course of the flight and the general geologic and tectonic features traversed. The flight line begins south of Olympia, Wash., and proceeds south across the Puget-Willemette depression to the Columbia River. Thence it proceeds eastward along the Washington-Oregon border across the Cascade Mts. and lava flows and the Umatilla basin to Pendleton, Ore. From Pendleton it traverses the Blue Mts. uplift of Oregon in a southeasterly direction, and then to the Boise basin of southwestern Idaho. The flight line swings in an easterly direction as it passes over the Snake River downwarp to the south of the Idaho batholith. It then passes over the northern portion of the Great Basin and the heavily overthrust area at the intersection of the Utah, Idaho, and Wyoming borders. The flight then assumes an easterly course to cross the series of basins and uplifts of southern Wyoming and terminates near the western flank of the Laramie uplift. It should be clearly understood that all statements in this article pertaining to the magnetics were interpreted on the assumption of elongate anomalies transverse to a single profile. Hence any theories or ideas advanced here are in line with future paths of research rather than trying to prove or disprove existing data. Magnetic Interpretation: Depth determinations were made by the slope method of Peters: which is stated as follows: "Draw a line in the maximum slope (at the point of inflection); draw a line whose slope is one-half this maximum slope; draw two lines parallel to this line tangent to the anomaly curve. The horizontal distance between the points of tangency is approximately equal to 1.6 times the depth [or the distance times 0.6251." Certain assumptions must be made for determinations of the causes of the magnetic anomalies:' 1) The anomaly is caused by a susceptibility change rather than basement relief. 2) Polarization of the basement rocks is in the same direction as the earth's inducing field. 3) The disturbing magnetic mass has a great horizontal length in comparison to its width and its sides are vertical and of great vertical extent. 4) The anomaly is unique and not affected by the anomalies from nearby sources.

Jan 1, 1957