Search Documents

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout 'from a plating bath by modifying the design and position of two boltholes.' A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.' The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com'pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By A. H. Geisler

INTRODUCTION THE correlation of property changes during precipitation with structure has progressed, sometimes rapidly but other times more slowly, since the fundamental discovery of Merica, Waltenberg and Scott.1 The predominent factor that hampered the progress has been limitations imposed by the various detection methods. Refinements in X ray diffraction techniques and in metallographic methods, which have been extended by the electron microscope, have contributed new information within the last few years. These permit an extension of the theory as proposed by Mehl and fetter in 1940.2 Now that a suffcient number of alloys has been investigated to establish a general mechanism of the precipitation process, a correlation of the facts into a generally applicable theory of age-hardening is both warranted and desirable. 'I he purpose of the paper is to provide an orderly correlation of the phenomenological facts of precipitation hardening. Speculation on mechanism of hardening will be confined to that consistent with existing theories of hardening. Age-hardening accompanies the formation of a new structure, the precipitate, as provided by an alloy system in which solid solubility decreases with decreasing temperature. Upon this premise alone all such systems would be expected to include age-hardenable alloys. Alas, this is not always the case. Few attempts have been made to explain the variable degree of age-hardening among different alloys or to explain the influence of small alloying additions upon the hardening. Dispersion hardening as originally postulated3 is not adequate.* Coherency hardening-the term that will be used to distinguish the properties of a two-phase mixture in the unique and unstable transition state at which the phases are strained into precise atomic registry (continuity or coherency) in planes

Jan 1, 1948

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967

By Carlos E. Roggero

The influence of high temperatures on the zinc roasting practice has been investigated by full-scale tests in fluid bed reactors operating at temperatures from 950° to 1150°C. It was definitely shown that, throughout the range, an increase in tem perature resulted in a 2 to 3 pct increase in zinc solubility because of decreased content of zinc fer-rite and lowered sulfide sulfur. The former is attributed to thermal decomposition of ZnFe,O,, and the latter to increased oxidation rates, ad longer retention times. Data on the gveatly increased volatilization of lead, cadmium, and silver above 1000°C, are presented. A considerable fraction of the iron present in the feed was also transferred at high temperatures from the coarse roaster discharge to the flue dusts. AS part of its metallurgical complex1-3 situated in a 12,000 it Andean valley at La Oroya, Peru, Cerro de Pasco Corp. (a wholly owned subsidiary of Cerro carp.) operates a 150 short ton per day electrolytic zinc refinery. Electrolysis is carried out at a cathode current density of 65 amp per sq ft with an electrolyte content of 55 g per liter of Zn and 150 g per liter of su lf uric acid. Due to the high iron content of the marmatitic concentrate used, a large fraction—about 15 pct—of the zinc reports in the leach residues. To minimize such losses, efforts have been exerted toward improving calcine solubility. One method, as noted in the literatre,, is to retard zinc ferrite formation by decreasing the roasting temperature. Unfortunately, such a procedure tends either to reduce the roaster throughput or increase the sulfide sulfur in the calcine. Consequently, this approach was discarded in favor of experimental work in the opposite direction, i.e., high temperature roasting. Full- scale tests were promising and resulted in the granting of a patent to Cerro de Pasco carp.' After a brief account of plant equipment and operating procedure, this paper describes the tests made and attempts to assess the results obtained. GENERAL PLANT LAYOUT AND OPERATION The Roasting Plant, see Fig. 1, comprises an agglomerating plant feeding three fluid bed roasters with a combined capacity of 10,000 tons per month. The Peruvian patent rights on this process were purchased from the New Jersey Zinc Co. The concentrate, assaying: is pelletized to a -3 +14 mesh product and fed to the fluid bed roasters. The roaster exhaust gases pass through a waste heat boiler, cyclones, a fan, and an electrostatic precipitator. Approximately half of the dust collected in the cyclones returns to the pellet-izing plant as one of the binding ingredients, the remainder joins the cooled bed discharge ('overflow') and is conveyed to the grinding plant. The -35 mesh product obtained, together with the dust collected in the electrostatic precipitator constitute the feed to the leaching plant. Batch leaches are made in vessels with mechanical and air agitation, the residues are separated and washed in Burt Filters, and pumped to storage ponds. THE FLUID BED ROASTERS Two reactors are as shown in Fig. 2, and the third,' of about the same configuration, is approximately 40 pct smaller. The total grate and freeboard (just below the gas outlet) areas measure 170 and 426 sq ft respectively. The feed, continuously weighed and controlled by Merrick Weighto-meters fitted with variable speed motors, enters the reactors at the top of the expanded bed level. The coarse calcine overflows through the opposite end by

Jan 1, 1963

By P. T. Carter, A. B. Murad, H. B. Bell

N. A. Gokcen (Michigan College of Mining and Technology, Houghton, Mich.)—The activities of silica, represented in Fig. 5 for the systems MnO-SiO2 and CaO-SiO2, are in disagreement with the established binary phase diagrams. At Ns102 = 0.50 in MnO-SiO2, and at Ns102, = 0.65 in CaO-SiO2, each binary system is saturated with respect to silica at 1550°C, and therefore as102, is unity in each case. The curves for as102 (FeO-SiO2) and as102, (MnO-SiO,) should nearly co-

Jan 1, 1953

The Mexican Government is building a mill at Churunibave in Sonora to handle lead, zinc, and copper ores. This development was sparked by increased mining activity in Mexico and Arizona caused by the Korean war. Pickands Mather, acting for a group of iron ore producers, is negotiating an agreement with Steep Rock Iron Mines, Ltd. to explore and perhaps lease iron ore property covering more than 1000 acres in the Steep Rock Lake area in Western Ontario. Plans call for the early commencement of an exploratory program. Other members of the group by Pickands Mather are Bethlehem Steel, Youngstown Sheet & Tube, the Steel Co. of Canada, and Interlake Iron Corp.

Jan 3, 1951

By David L. Pentz

This paper discusses exploration objectives and requirements for a nuclear repository in the U.S.A. The importance of designing the exploration program to meet the system performance objectives is emphasized and some examples of the extent of exploration required before the License Application for Construction Authorization is granted are also discussed.

Jan 1, 1984

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.'s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.' P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,' R. T. Hukki,' D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.'s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott's western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott's Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By Paul Merica

ONE of the most useful, and at the same time least commonly used, methods of thermal analysis for the determination of transformations in metals and alloys consists in the recording of the tune intervals required for successive increments of temperature change during heating or cooling, the temperature of the furnace containing the specimen being altered at a uniform rate. The curve obtained by plotting these time intervals as a function of the mean temperature of the specimen during the interval is called the inverse-rate curve. It is probably due to the fact that no simple and convenient method has apparently been available for the measurement of the successive time intervals that this method has not been so generally used as, for example, the differential method, for which several tykes of automatic or semi-automatic apparatus have been designed. Whenever this method has been used, the intervals have usually been measured with the use of a chronograph; its operation as practised at the Bureau of Standards' is as follows: The temperature of the specimen is measured by a thermocouple and a dial potentiometer. The operator sets the potentiometer at successive values of the electromotive force differing by equal increments, usually 0.02 millivolt, and records the exact instant on the chronograph, by pressing a contact key, at which the galvanometer coil passes through its null position. Two-second intervals are also recorded on the chronograph record, and the number of 'seconds elapsing between successive signals is afterward counted from the record and plotted as a function of the electromotive force or of the temperature. This is an admirable method and by it most minute thermal arrests may be detected, but it requires a good chronograph, which is generally difficult to obtain, and the time of one operator during the recording and, subsequently, to read the intervals from the record; the latter operation often takes from one to two hours.

Jan 7, 1919

By K. A. Lambert

In the Anthracite Region there are considerable areas where the original mining was done 50 or more years ago. In this original mining, the pillars that were left proved inadequate in size for the support of the roof, which has since collapsed as a result of squeezes, and completely filled the original openings. In an endeavor to recover the coal which remains in the pillars in such areas, the reopening cost for development, as well as for pillar recovery, has been excessive in many instances. Various methods have been tried out with a view to lowering the cost, in order that the greatest possible percentage of recovery of the reserve tonnage may be realized economically. Ordinary hand mining necessitates the driving of development road 10 ft. wide in the clear between timber legs, with 6 ft. of clearance over the rail to accommodate mine cars; collars or crossbars on the timber sets have been difficult to maintain in these openings in the heavily caved condition, especially in beds where the overburden is great,. Numerous failures have occurred on these development road timbers because of roof movement resulting from removal of pillars. The actual removal of pillars from this development work has been costly because full-width openings for transporting mine cars to the face have to be maintained by cleaning caved material from alongside the pillars, or skipping up along the pillars where pillars of sufficient width are found. Shaker-chute Methods A method of developing such caved conditions and recovering pillars tributary to this development, utilizing shaker chutes, is being tried out with considerable success at Loree colliery. An outline of the chute and apparatus is shown in Fig. 1, which indicates the location of pillars and caved material. The cost of both labor and material required in the recovery of such coal is considerably less than by ordinary hand methods. In order to try out this method of mining a location was chosen where a tightly caved area had been developed by ordinary hand methods to within 300 ft. of the property line. The original bed height was 12 ft., with an overburden of 325 ft., but on account of the squeezes which

Jan 1, 1931

By M. J. Greaves, Alan English

Pelletizing on a commercial scale is only 10 years old; yet in this period more than 150 million tons of pellets have been produced. Instrumentation and controls have played an important part in the development of an entirely new industry in almost unprecedented time. Initially, most control circuits used in the pelletizing industry were manually operated, since the confidence factor in instruments and controls was quite low at that time. This changed considerably in recent years and improvements in the use of instruments and controls have probably developed more rapidly in pelletizing than in any other metallurgical process. Now, within a decade of the start of commercial operations, the use of manually operated controls has changed and consideration is being given to the utilization of computers for data logging and control purposes.

Jan 7, 1965

By M. E. Wadsworth, K. C. Bowles, H. E. Flanders, R. M. Nadkarni, C. E. Jelden

The kinetics of precipitation of copper on iron of various purity were carried out under controlled conditions. The rate of reduction has been correlated with such parameters as copper and hydrogen ion concentration, geometric factors, flow rate, and temperature. The character of the precipitated copper as a function of flow conditions and rate of PreciPitation has been observed under a variety of conditions. ThE precipitation of copper in solution by cementation on a more electropositive metal has been known for many years. Basile valentine' who wrote Currus Triumphalis Antimonii about 1500, refers to this method for extraction of copper. Paracelsus the Great2 who was born about 1493 cites the use of iron to prepare Venus (copper) by the "rustics of Hungary" in the "Book Concerning the Tincture of the Philosophers". Agricola3 in his work on minerals (1546) tells of a peculiar water which is drawn from a shaft near Schmölnitz in Hungary, that erodes iron and turns it into copper. In 1670, a concession is recorded4 as having been granted for the recovery of copper from the mine waters at Rio Tinto in Spain, presumably by precipitation with iron. Much has been published in recent literature on the recovery of copper by cementation, the majority of the articles being on plant practice.5-24 The rest include articles on investigation of the variables involved25-28 and a review of hydrometallurgical copper extraction methods." This literature has established: a) The three principal reactions in the cementation of copper are Cu + Fe — Fe+4 +Cu [ 11 One pound of copper is precipitated by 0.88 lb of iron stoichiometrically. In actual practice about 1.5 to 2.5 lb of iron are consumed. 2Fe+3 + Fe — 3Fe+2 [21 Fe +2H'-Fe+2 + H2 [3] Reactions [2] and [3] are responsible for the consumption of excess iron. Wartman and Roberson'28 have established that Reactions [ I] and [2] are concurrent and much faster than Reaction [3]. b) Acidity control is important in the control of hydrolysis and the excessive consumption of iron. he commercial workable range is approximately from pH = 1.8 to 3." c) Iron consumption is closely related to the amount of ferric iron in solution. Jacobi" reports that, by leaving the pregnant mine waters in contact wi th lump pyrrhotite (Fe7S8) for 3 hr, all the iron was reduced to the bivalent condition and scrap iron consumption was cut to 1.25 lb scrap per pound of copper precipitated. He also reported that SO2 has been used successfully to reduce ferric iron to the ferrous state. d) The ideal precipitant is one that offers a large exposed area and is relatively free of rust. e) High velocities and agitation show a beneficial effect upon the rate of precipitation, as it tends to displace the layer of barren solution adjacent to the iron and also dislodges hydrogen bubbles and precipitated copper to expose new surfaces. Little work, however, has been published on the reaction kinetics of copper precipitation on iron. Cent-nerszwer and Heller20 investigated the precipitation of metallic cations in solutions on zinc plates. They found the cementation reaction to be a first-order reaction. The rate constant was independent of stirring for high stirring rates and they concluded that the rate is governed by a diffusional process at low stirring speeds and by a "chemical" process at higher stirring speeds where the rate reaches a constant value. This conclusion has been challenged by King and Burger30 who could not find any region where the rate was independent of the stirring speed, although the rate constant they had obtained for high stirring speed was greater than the maximum value of the rate constant reported by Centnerszwer and Heller (by a factor of six). King and Burger, therefore, concluded that the rate of displacement of copper was controlled only by diffusion. Cementation of various cations on zinc has been summarized by Engfelder.31 APPARATUS A three-necked distillation flask of 2 000-mm capacity was used as a reaction vessel. A pipet of 10-mm capacity was introduced through one of- the side necks, the sample of sheet iron, mounted in a rigid sample holder, through the other, the stirrer being in the middle as shown in Fig. 1. The whole assembly was immersed in a constant-temperature bath. The stirrer was always placed at the same depth in the solution. EXPERIMENTAL PROCEDURE Reagent-grade cupric sulfate (J. T. Baker Chemical Co., N.J.) was used to make up a stock solution containing 10 g of copper per liter which was then diluted to various concentrations as required. Experimental data were obtained by measuring the amount of copper and iron ions in solution at successive time intervals. The initial volume of the solution was always 2000 ml, 10-ml aliquots being removed each time for chemical analysis. Because the total volume change of the solution was less than 10 pct, no correction was used for solution volume change. Nitrogen was bubbled through the solution before and

Jan 1, 1968

By A. B. Kinzel, Walter Crafts

A PRevioUs study1 of the relations of impact strength to inclusions showed that the dynamic strength of steel is lowered by the presence of visible counted inclusions, but that other factors comprised in the term "body" have a marked influence. The previous work was carried out on selected steels from a single source, so that the body factor was purposely minimized, but even under these conditions it was found that inclusion counting or the use of the commercial inclusion rating is not satisfactory. The tensile-impact test, however, was indicated as a satisfactory measure of dynamic strength. It was further suggested that the tensile-impact test should be so standardized as to be suitable for use in specifications, and that the hardness factor should be worked out over a sufficient range to admit ready commercial use of the tensile-impact test. In accordance with these suggestions, and in view of the fact that the steels reported in the previous paper were selected and treated so as to have a minimum variation in body, hardness and structure, further work has been performed on a variety of steels which are not limited by these conditions. The word "body" is used here for want of a better term. It is simply a convenient expression which comprises the effect, of the various unknown factors that modify the dynamic strength of the steel. Thus at our present state of knowledge, the writers have chosen to consider hardness, structure and counted inclusion content as factors not comprised in the term "body," and such factors as raw materials, process of melting, fabricating, etc., as comprised in the term "body." Numerous grades of steels made in several ways have been taken from different sources and have been heat-treated to varying hardness by normalizing and by quenching and drawing. The results, therefore, may be considered to be generally applicable to current engineering steels. A certain limitation with respect to the hardness at which steel should be tested still seems necessary. The upper limit of this hardness range has

Jan 1, 1931

By W. B. Lilienthal

A considerable saving in time and money has been effected by use of a specially designed stainless steel container for laboratory drilling mud test work. This container involves use of a standard tall-form stainless steel beaker for service in which the mud sample is heated to an elevated temperature and maintained there for protracted periods of time, while undergoing agitation to facilitate mixing of mud components. Agitation is accomplished by rotating the filled containers on motor-driven rollers within an oven. Several porcelain balls are generally placed in the containers to further improve agitation. Soft glass containers (.Mason jars) were used in this service in early work, and were found to be unsuitable for the following reasons: 1. Poor resistance to thermal shock. 2. Containers could withstand only relatively low pressures. 3. Accidental breakage in handling. 4. Chemical deterioration and subsequent mud contamination from reaction of high pH muds with the glass at elevated temperatures. Pyrex containers were also considered, but, inasmuch as they provided improvement only in items 1 and 4 listed above the additional cost was not believed to be justified. A scale drawing of the container is shown in the figure illustrating details in cross-section. A pressed stainless steel lid was fabricated to match the rolled edge of the beaker

Jan 1, 1950

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

By R. V. Vines, E. M. Wise

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By E. M. Wise, R. V. Vines

It is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. Conclusions 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportioilal limit, very low; elongation, 37.5 per cent in 2 inclles. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545' and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or 110 grain grourtll resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times. Prior Work As already mentioned, data on the recrystallization of platinum are scarce. Gmelin'sl handbook, which summarizes data published earlier than August 1938, lists values ranging from 400' to 810°C. for the minimum temperature of recrystallization of samples with rather indefinite

Jan 1, 1940

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm's length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"' developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

By L. B. Harris

Continuous cyclic unloading during tensile work hardening of polycrystalline zinc at room temperature enables specimens to sustain greatly increased extension. Such enhanced ductility is associated with creep-type extension, during which the cyclic component appears to promote relaxation of internal strains. It is possible to trace the transitions from tension, through enhanced cyclic extension, to fatigue and relate the observed behavior to simpler types of deformation. DISTINCTIVE deformation behavior has been shown to occur when loading includes both cyclic and unidirectional components. For aluminum and copper extended by a sequence of progressively biased strain reversals, coffin1 observed greater fracture ductility and lower flow stresses than during monotonic tension. This may be compared with the reduction in hardness obtained from conventional fatigue softening. But fatigue softening is accompanied by enhanced fatigue life,' whereas Benham3 found that fatigue life was reduced when copper continuously extended during axial load cycling. The corresponding specimen elongation, for large cyclic load amplitudes, was greater than during normal tension. Under different conditions, Bendler and wood4 found that torsional fatigue initiated extension in copper under low tensile loads previously in equilibrium with the specimen; fatigue life was again reduced. Thus there is a type of cyclic softening which is associated with reduced fatigue life and which occurs when the cyclic loading is accompanied by a unidirectional strain component. Further, the fracture ductility or extension obtained from the unidirectional component can exceed that obtained in the absence of cyclic load. Specimen extension was not initiated by axial fatigue at small load amplitudes;3 hence Benham's work distinguishes between fatigue at large and small amplitudes, the former often being linked with unidirectional deformation because of similarities in strain Structure. The initiation of tensile extension during torsional fatigue,4 however, occurred with small amplitudes. Comparable changes in behavior have been ob- served during creep. kennedy' found that combined cyclic and creep stresses on lead at 32°C increased the rate of elongation over that for simple creep, the consequence being a reduction in creep life. It was also demonstrated that small cyclic stresses applied after creep deformation initially increased recovery, but that prolonged application produced only normal fatigue hardening. It is clear that physical properties can be changed by interaction between the cyclic and unidirectional deformations, but owing to the number of different ways in which the deformations can be combined and the large number of possible variables for each combination, trends of behavior become easily obscured. One definite conclusion is that enhanced ductility or increased extension can be obtained by cyclic action, and it is this process that has been investigated for the tensile test by measurements of the extra tensile strain produced by the addition of a cyclic tensile component. EXPERIMENTAL PROCEDURE Material. Specimens were 99.99 pct Zn wire of 1.6 and 2.0 mm diam. Mean grain diameter was 0.02 mm, sufficiently small to give a ductile necked-down fracture under all loading conditions. All experiments were conducted at an average temperature of 20°C. Normal Tension. Unidirectional tensile curves at different strain rates were obtained from an In-stron testing machine, on which load-time curves were recorded autographically, using gage lengths of 5 and 10 cm. Straining was at constant cross-head velocity, and quoted strain rates are with reference to initial specimen length. Measurements of total elongation under simple tension were also made on the tensile machine that had been modified to incorporate an added fluctuating load. Combined Tension and Rapid Cyclic Load. An electromagnetic vibrator was coupled to the elastic beam of a Hounsfield ensometer- and driven sinus-oidally from a power amplifier at frequencies from 20 to 360 cps, the flexible connecting links on the tensometer being replaced by rigid fixtures to eliminate lateral vibration in the specimen. One end of the specimen was pulled by the normal extension drive of the tensometer while the other end, fixed to the elastic beam and vibrator, was subjected to rapid oscillations of load. It was thus possible to apply cyclic load to a tensile test without altering the rate of extension of the specimen

Jan 1, 1964