Search Documents

By John Stewart

The market at present supplied by shipments from the phosphate districts of Quebec, Ontario, and New York State requires high-grade ore, carrying from 75 per cent. to 90 per cent. of phosphate of lime. In sorting out such material by hand, much valuable phosphate is necessarily left in the "culls" or refuse, besides which, much phosphate-rock of low-grade is not now mined at all, because it cannot be made available by the crude method of cobbing and hand-sorting. The utilization of such material, which would, of course, greatly benefit this industry, requires either a mechanical separation or a chemical process which would concentrate the phosphate in a form suitable for agriculture. Considering the rich phosphate now shipped as the first class, we may arrange the lower grades in three classes, as follows: Second Class.—Cull-ore from the first class, and the mass of deposits having, as gangue, pyroxene or hornblende. The following table gives the hardness and specific gravity of the minerals concerned: Hardness Spec. gravity. Apatite,....... . 5 3.1 to 3.25 Crystalline limestone (pink calcite),. 3 to 4 2.5 to 2.9 Pyroxene,..5 to 6 3.23 to 3.5 Hornblende,.5 to 6 2.9 to 3.4 Feldspar (orthoclase),. .. . 6 to 6.5 2.5 to 2.6 It is evident that when pyroxene and hornblende are present in large proportions, this ore cannot be successfully concentrated by crushing and jigging. It may be reduced to fine powder by successive treatment in a rock-breaker and a Sturtevant or Frisbee-Lucop mill, or other suitable apparatus, and in this condition it could be largely used by applying it freely upon exhausted clay soils, such as occur in Quebec and Ontario. The occupants of these once fertile river-lands are, however, hard to move in the direction of such improvements. When water-power is at hand, the cost of crushing

Jan 1, 1893

By Rudolf Bernhard

STATIC soil investigations with more or less heavy loads and extensive borings do not always have efficient results; also, they are very expensive. The new geophysical method of dynamic tests described herein is simple and cheap and avoids several disadvantages of the routine investigation, thus forming a useful supplement to the older methods and even at times replacing various static tests. The fundamental principle of dynamic soil tests consists in the appli-cation of artificial vibration. The technique employed is essentially geophysical in nature and in some respects is akin to seismic studies. Artificial vibration may be excited by centrifugal forces resulting from eccentrically supported rotating masses. The reactions of soil and structures caused by these vibrations may be measured. Their dynamic constants, such as amplitudes, phase speeds, damping, reflection, and interference effects, can be investigated. This geophysical method has been used for several years with increasing success. The results of these tests, summarized at the end of the paper, indicate that this method opens a new field for the practical engineer in investigating soils (capacity and formation), foundations, dams and structures, and especially buildings that must withstand earthquakes.

Jan 1, 1938

By Robert W. Coughlin

Pulverized coal has been introduced at the anode where it is oxidized during the electrowinning of metals from their aqueous solutions This substitutes an electrochemical reaction between coal and water for the usual oxygen-evolving half-cell reaction at the anode, with the result that overall cell potential is significantly lowered and the consumption of electrical energy is correspondingly reduced. Experimental results are reported for electrowinning copper as an example of this novel modification of the electrowinning process in this example, the use of coal lowered the consumption of electricity by two-thirds of the requirement of the conventional process When the potential electrical energy of the coal consumed is considered the new, coal-assisted process consumes about 45% less energy, and the energy costs (combined costs of coal and electricity) are reduced by about 50%.

Jan 1, 1981

By D. W. Mitchell

Mine fires are a serious hazard; surveys show that the coal-mining industry lags considerably behind industry in general in planning and training for fighting fires, and providing adequate fire-protection facilities. The results of the experiments discussed in this paper emphasize that every effort must be made to extinguish a fire in its incipient stage. The research also demonstrated that extinguishing agents and techniques, superior to those presently used in most operating mines, are available. An underground coal mine fire, if not extinguished quickly, can develop rapidly, create a serious hazard, and cause loss of life and property. The problem of controlling a fire increases in direct relationship to the time interval necessary to initiate control measures; as the fire increases in size and intensity it becomes progressively more difficult to cope with roof control, visibility, ventilation, and explosion prevention. Despite the constant vigilance of the industry, the number of coal mine fires is increasing. During the eight-year period, July 1952 to July 1960, following enactment of the Federal Coal Mine Safety Act, the Bureau of Mines investigated 401 fires that caused 30 fatalities and 75 injuries. More than half of these fires burned for more than one shift; 20 pct could not be extinguished by direct attack and had to be sealed. Agents and techniques for extinguishing simulated mining-machine and underground coal fires have been investigated in the Bureau's experimental coal mine. The research shows that visibility in the fire area is a primary factor affecting control operations. Associated with good visibility is accessibility to the fire; the closer the attack can be made, the less time and quantity of agent are required for extinguishment. Approach to the fire and visibility are hindered by the smoke and hot gases backing up against the ventilating current. In open entries an increase in air velocity assists in driving smoke ahead; at low airspeeds approach can be made by placing a brattice across the lower two-thirds of the entry, pushing the smoke ahead with water sprays, or discharging rock-dust from a rock-dust distributor. In a dead-end entry, fires can be approached by coursing fresh air along an airtight line brattice. However, it is safer, easier,

Jan 1, 1962

By Ali Altway, M. E. Tunison, T. W. Chapman

Simulations of various contactor configurations for simultaneous extraction or stripping of two metals reveal the dependence of conversion and selectivity on operating and design parameters A two-film mass transfer model is used to provide the rates in countercurrent column and stirred-tank cascade calculations Even in these mass-transfer-limited cases the stoichiometry of the extraction reactions introduces nonlinearities and interactions between the two metal transfer rates, but these can be represented In a suitable model One conclusion is that a countercurrent column should be considerably more efficient than a cascade of mixer-settlers of comparable size.

Jan 1, 1981

By M. Lastra, A. Cruz, J. Menacho

The technical feasibility of treating exotic copper ore with an acid cure using concentrated H2S04 is studied. Applications in a conventional percolation leaching circuit for unaltered ore and in a conventional agitation leaching circuit for altered ore are examined. The main effects of an acid cure are to inhibit silica dissolution and to increase the sedimentation rate of agitated pulps. An increase in the rate and degree of copper extraction is also observed. Based on these results and the minimal additional investment required, acid curing appears to provide an excellent approach for treating exotic copper ores.

Jan 1, 1980

By A. C. Noble, D. E. Ranta

Orebodies with intricate three- dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer- assisted methods. 'The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral de- posits.

Jan 1, 1984

By A. M. Gaudin

Activation of sphalerite with silver ions results from the exchange of two Ag ions for one Zn ion in the sphalerite lattice. The exchange is proportional to the logarithm of time and proceeds until either of the reactants is consumed. Sodium cyanide prevents the activation of sphalerite by controlling the ratio [Zn++]/[Ag+]' in solution. If sphalerite has already been activated with excess silver, cyanide ions can deactivate sphalerite provided oxygen is present. SOLUBLE: silver salts are effective activators for flotation of sphalerite with potassium ethyl xan-thate as collector.* Since sphalerite takes up large quantities of silver ions rapidly,2-4 investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hy-drosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Ii'inally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure. The specific surface of two samples from the 65/100-mesh sphalerite stock, measured by krypton gas adsorption," was 420 cm2 per g. Compared with spheres of the same size and specific gravity, the prepared mineral had five times as much surface. Results of a wet chemical analysis and of a spectro-graphic study are given in Table I. Manganese, nickel, tin, indium, thallium, cobalt, and magnesium were not detected spectrographically. All solutions were preparid by -adding reagent-grade chemicals to conductivitv water. which had been previously saturated with the desired gases. Nitrogen and oxygen were purified, but no attempt was made to purify the laboratory air. Radioanalysis was carried out with prepurified Ag110 tracer obtained from the Oak Ridge National Laboratory. The complete decay scheme for Ae is complex. Its primary emissions are 0.09 and 0.55 mev ß rays and 1.48 mev y raysB and its half-life is believed to be 270 days. In preparation of solutions of AgNO3, the amount of Ag110 added was negligible compared to that of the inert silver. Abstraction of silver from solution by sphalerite was measured after agitation of 1.5 g sphalerite with 20 ml of solution in 50-ml pyrex flasks. All sample preparations were carried out in a dry box so that the proper atmosphere could be maintained. After the mineral had been agitated in the silver nitrate solution, an aliquot of the solution and a sample of the wet mineral were transferred to separate counting vials and weighed. The solid sample was dried and re-weighed and the activity in both vials measured by means of a scintillation counter. With scintillation counting it is possible to count y radiation from the solid and liquid, a distinct advantage over the older ß-ray counting techdiques.4 All measurements of silver activity were made using a sodium-iodide well-type scintillation counter. The amount of zinc in solution was measured colorimet-rically by the monocolor method of Sandell.7 Activation Studies Exchange Between Zinc Ions and Silver Ions During Activation: The increase of Zn++ in solution during activation with Ag+ is shown in Table 11. These data indicate a replacement of one Zn++ by two Ag+. Analysis of a separate two-month agitation test indicated that the replacement of Zn++ by Ag+ was, as expected, in the molar ratio of 2.0.

Jan 1, 1958

By Edward L. Wilson, Keshavan Nair, Ranbir S. Sandhu

In planning and designing of underground excavations and construction, it is of considerable importance that the stresses and displacements in the rock mass subjected to arbitrary sequences of unloading and loading be within allowable limits. For determination of the stress and displacement fields, the usual approach is to treat the rock as an elastic material and to apply the principles of the theory of elasticity. However, analytic solutions are available only for a limited class of problems of simple geometry and idealized material properties. Nonhomogeneity and anisotropy of material coupled with complex geometrical configuration and initial stress fields that are almost always preexistent in rock masses at great depths, render the problem intractable by analytical methods. Approximate solution techniques using numerical procedures have, therefore, to be resorted to. The finite element method as applied to plane stress analysis was introduced by Clough.1 It has developed into a powerful tool for the analysis of various field problems in structural and continuum mechanics. The method is well documented in the literature2-6 and, therefore, its historical development will not be discussed here. Wilson's analysis of the plane stress/strain problem has found extensive use in the area of soil and rock mechanics including stresses around underground openings; stresses and displacements in dams, foundations, etc.7-11 In his analysis of the axisymmetric solid,3 Wilson proposed a procedure to allow for certain cases of nonlinear material properties. In this chapter, the develop-

Jan 1, 1972

By Paul-Emile Mercier

LOADING efficiency depends on cycle capacity of the loader, conditions of the mine, and mine organization. Cost of operation is the final criterion. Two types of loaders are analyzed-the boom shovel and the tractor-excavator. Studies were made in an open pit at Kimberley, Nev., where shovels are the production units and the tractor- excavator is a clean-up loader. The report deals mainly with the analysis of cycle and output. Problems of pit organization are not acute. (Other studies included in the original report and omitted here covered tractor-excavator application underground.)

Jan 4, 1957

By Richard E. Goodman

Rock slope stability assumes different roles in decision making as a mining venture develops and, accordingly, geological investigations vary in thought and in deed according to the project stage. During exploration, stability questions bear on the decision whether or not to mine, because their resolution affects the cost of mining. During the mine lay-out stage, stability is a key factor in deciding how to mine. Finally, during mine operation, stability affects safety and operating costs, and therefore, pit productivity. Among the many considerations influencing stability, rock mass classification and geological environmental factors count heavily. The rock mass behavioral class depends upon the rock character and its degree of fracturation. The loads on the rock are derived from the environmental factors of initial state of stress and the water regime. Of course, stability is also tied to a host of non-geological factors such as the pit geometry, mining style, relative wealth, philosophy of mine operation, and accident history. METHODS OF STABILITY EVALUATION AND CORRESPONDING INVESTIGATORY TOOLS The purposes of the geological investigation are to identify and evaluate the geological factors influencing stability so that the vital questions can be analyzed. The tools selected for stability analysis reflect the stage of development of the mining scheme and therefore the geological investigations, which must furnish data for the analyses and must vary with the project stage. For exploration and mine planning, the methods of resolving stability questions must meet the need to evaluate numerous parameters in limited time; examples of such methods are stereographic projections (1, 2, 3) charted solutions(4) and simple physical models (5, 6). An investigation program that employs geological mapping tools and aids to mapping, such as geophysics, with relatively few rock tests, is in balance with these analytical methods. First data about the water regime are obtained from observed piezometric levels, and the initial state of stress is queried simply through geological inference and experience. In the layout stage more elaborate physical scale models (7) and perhaps finite element models (8, 9, 10, 11, 12), will be relevant to the design process and therefore much more detailed geological investigation is required. The scale of observation of both rock material and joints will be significantly enlarged and mechanical tests of rock and joint strength

Jan 1, 1972

By C. S. Roberts

The creep mechanism and kinetics of fine-grained magnesium have been studied over the temperature range 200&apos; to 600°F. As a result of a photographic study of microstructural changes, transient and steady-state creep components have been correlated with slip, subgrain formation, and cyclic deformation at the grain boundaries. THE approach of this research has been the blend of a quantitative study of the creep strain of polycrystalline magnesium as a function of time, stress, and temperature with direct microstructural observations of the operative deformation processes. The validity of the conclusions is dependent on the condition that the microstructural changes seen on the polished surface qualitatively represent those occurring in the bulk of the metal. The work was intended as much to lay a background to a study of highly creep-resistant magnesium alloys as to provide a description of the behavior of the base metal itself. The spectroscopic analysis of the electrolytic magnesium used in this study is as follows: Al, 0.009 pct; Ca, <0.01; Cu, 0.0011; Fe, 0.021; Mn, 0.012; Ni, 0.0004; Pb, 0.0012; Si, <0.001; Sn, <0.001; and Zn, <0.01. The impurity level is approximately that of commercial magnesium alloys. The original ingot was melted under Dow type 310 flux and cast as a 3 in. diam billet. It was extruded into 1 in. flat stock under the conditions: billet preheat 800°F (1 hr), container and die temperature 800°F, speed 3 ft per min, and area reduction ratio 45:1. The extrusion process was chosen in preference to rolling and recrystallization because it allowed easier grain size control from specimen to specimen. The grains of the extruded metal were fairly equi-axial and uniform in the size range of 4 to 6 thousandths of an inch. The preferred orientation of basal planes about the transverse direction was determined by an X-ray diffraction surface reflection method. A beam of filtered copper radiation was directed at an angle of 17" to both the transverse direction and the surface yet perpendicular to the extrusion axis. Analysis of the (002) diffraction arcs in the resulting photographic patterns gave an approximate intensity distribution along the great circle which extends through the center of the basal plane pole figure and to the extrusion axis poles. Successive layers of metal were removed by macro-etching between exposures. The extruded texture is relatively sharp, but the most significant point is the position of the maximum basal plane pole density and its variation with depth below the surface. Fig. 1 shows that this maximum is rotated 15" from the normal at the surface toward the extrusion direction. Such an inclination has been reported for extruded 1 pct Mn and 8 pct A1-0.5 pct Zn alloys.&apos; The inclination decreases until the maximum splits at about 0.025 in. depth into two elements of equal and opposite rotations from the ideal. The double texture persists to as great a depth as was experimentally convenient to examine. It probably continues to the very center of the extrusion. There is no great change in the sharpness of the individual elements of the texture with depth. A plate of metal about 0.015 in. thick at the surface of the extruded stock was produced by etching. A transmission diffraction pattern was made for the purpose of determining any preferred orientation of a direction in the basal planes. Relatively uniform {loo) and {101) rings were produced. There is little tendency for parallelism of a given direction in the plane with the projection of the extrusion axis on it. The creep specimens were machined from 6¼ in. lengths of the extruded stock. Creep was measured on the reduced section, ½x1/8X2¼ in. long. This section was electropolished on one side for the studies of microstructural changes during creep. An orthophosphoric acid-ethyl alcohol electrolyte was used under the conditions recommended by Jacquet.² Hand polishing was used for previous mechanical preparation. Electropolishing was continued until all mechanical twins had been removed. The electro-polished surface was protected from oxidation during creep testing by a thin layer of silicone oil. All micrographs were taken at room temperature on conventional metallographic equipment and after removal of the oil film. The creep tests were performed with machines which have been described in detail by Moore and McDonald." Five testing temperatures, 200°, 300°, 400°, 500°, and 600° ±3°F were used. Difference in temperature between the two ends of the specimen reduced section was 2°F or less. The testing was done at constant load. Strain readings were taken as frequently as necessary to develop usable creep curves. Tensile Creep vs Time, Stress, and Temperature A definition of terms is necessary. Whenever successive sections of a creep strain-time curve show decreasing, constant, and increasing slope with time they will be termed primary, secondary, and tertiary

Jan 1, 1954

By R. Maddin, A. Lawley

Single crystal Mo-Re alloys (99.99+ purity), grown by electron bombardment floating zone heating, were deformed in tension at temperatures from -196° to +200°C. At -196oC, Mo-6 pet Re and Mo-20 pct Re alloys deform by slip on systems of the type (101) [1ll]. Above-78oC, the operative slip system is of the type (112) [111], (101) [1ll], or (211) [1ll], depending upon orientation. Mo-39 pct Re alloys deform by twinning and slip at all test temperatures with a (112) [111] type twinning system. Critical resolved shear stress for slip and twinning is calculated as a function of composition and temperature, and the mechanical properties compared with those of less Pure polycrystalline alloys. HEXAGONAL close-packed rhenium, c/a = 1.615, is highly soluble in molybdenum. The bee molybdenum-rich solid solution extends to approximately 42 at. pet Re* at 2500°C,&apos; Fig. 1. Recent work on polycrystalline alloys has shown conclusively that the addition of rhenium to molybdenum improves both the fabricability and the low-temperature ductility.2"5 Similar behavior is observed for W-Re and Cr-Re alloys.5 Initially, Geach and Hughes2 found that the Mo-30 pct Re alloy could be cold rolled to approximately 90 pct reduction before the onset of cracking. The remarkable effect of the rhenium was later confirmed by Jaffee et al. 3-5 with an optimum condition of maximum strength combined with maximum ductility at the Mo-35 pet composition. At higher rhenium contents, the ductility was severely impaired due apparently to the presence of brittle tetragonal s phase, Fig. 1. In the Mo-35 pet Re alloy, at least 110 ppm (parts per million) oxygen could be tolerated before cold workability was reduced. By comparison, the corresponding tolerance figure in unalloyed molybdenum is ~ 10 ppm. The effect of rhenium was considered in terms of: 1) a reduction in oxygen solubility in the lattice; 2) a redistribution of intergranular oxide from grain boundary films to isolated spheres; and 3) the promotion of twinning as a further mode of plastic deformation. Paradoxically, twinning is often associated with brittle fracture in iron and the silicon irons.6&apos;7 Work to date has been restricted to are-melted and powder metallurgy polycrystalline material of ~ 99.9 pet purity. The present investigation was initiated for the purpose of determining the mode and crystallography of plastic deformation of a series of bee Mo-Re alloy single crystals over a wide temperature range from -196o to +200°C. Using high-purity zone-melted material (~ 99.99 + pet purity), the specific role of rhenium in the molybdenum lattice may be understood more fully since effects due to grain boundaries and oxide redistribution will be absent. At the same time, the study provides a comparison of single and polycrystalline deformation behavior. EXPERIMENTAL TECHNIQUES A) Preparation and Purity of Single Crystals. Alloys in the form of either are-cast and swaged or sintered and ground bar, 0.120 in. diam, were obtained from the Chase Brass and Copper Co. Alloy single crystals ~ 8-in. long were grown from the

Jan 1, 1962

ION exchange is one of hydrometallurgy&apos;s new tools, new in application, vet old in principle. Cation exchange between solution and a solid exchanger has been known for more than a century, but ion exchange is still in its infancy for metallurgical use. Still hampered by cost of media, it is faced with much development of actual physical handling. Growing consumption of the rarer metals and need to treat leaner ores are pushing extractive methods ahead. Public concern with stream pollution, or legal requirements, are forcing a clean-up of waste discharge. Industries are finding it vital to make some recovery from heretofore waste material to help pay costs of discharge treatment.

Jan 5, 1953

With over one year experience, Western Deep Levels Ltd., reports satisfactory operation with new features of its 200,000 ton per month gold reduction plant. Western Deep is Anglo American group&apos;s newest gold mine. It is situated 43 miles west of Johannesburg on the West Wits Line and will ultimately be extracting ore from a depth of 13,000 ft. Although the plant was put in production in March 1962, after a three month break-in period, construction of the fifth milling section was not completed until last month.

Jan 7, 1963

By R. A. Stauffer

THE chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper&apos; has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000°C in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating to about 1000°C in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. THE REPLACEMENT OF Li20 IN SPODUMENE A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide present in the ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh. Analysis of the spodumene was as follows: [ ] Lime (cp -200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000°C in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1947

By N. A. Tiner

A study was made of the effects of temperature, type of loading, and electric polarization on the fracturing behavior of copper and zinc coated with mercury. Copper showed an em-brittlement only in cyclic loading, whereas zinc showed an em-brittlenzent in both static and cyclic loading. The embrittle-ment of zinc in static loading was prevented by sub-zero cooling to a temperatzcre of about -70°F. The emhrittlement of both metals was sliglztly reduced by cathodic polarization of mercury. The basic processes involved in fracturing were discussed in the light of these observations. When a solid metal is in contact with certain liquid metals possessing high wetting characteristics, a weakening effect is produced, and the solid metal fractures in brittle manner at a relatively low stress. This lowering of the fracture stress generally is considered different from the stress cracking caused by a corrosive liquid environment and is attributed to the lowering of the solid-liquid interface tension at the grain boundaries.1-4 The purpose of this paper is to describe a number of observations on the special features of fracturing of copper and zinc coated with a liquid mercury film, and to analyze the basic processes involved in fracturing in the light of these observations. EXPERIMENTAL OBSERVATIONS I) Effect of Type of Loading—The evidence appears to indicate that in static loading, metals usually fracture by the initiation of microcracks in the interior preferentially at the grain boundaries or at the intersection of slip bands.&apos; In cyclic loading, cracks develop on the surface within the active slip zones, and gradually propagate with increasing num- ber of cycles.6&apos;7 Because of this difference in the manner of initiation of cracks, a series of bare and mercury coated copper and zinc specimens was subjected to static and cyclic loading, and their fracturing behavior was examined. The specimens were machined to 0.25 in. in diam and 1 in. in length from a high-purity commercial bar stock, and annealed at an appropriate temperature. Mercury was applied to the surface of the specimens by rubbing with cotton wool soaked in a saturated solution of HgCl2 or by etching with a dilute solution of HC1 and rubbing with purified mercury and by washing in water. The static tension load-extension curves were obtained by means of a Riele Screw Power Universal Testing Machine. The room-temperature load-extension curves for copper and zinc are shown in Fig. 1. The deformation behavior of copper, as judged from the general configuration of the load-extension curve, was not affected by mercury coating. The maximum load to fracture and the elongation at the maximum load were practically the same for both specimens. The mercury coated copper, however, showed somewhat less localized necking and had smaller reduction of area than the uncoated metal. The behavior of mercury coated zinc was radically different from the behavior of uncoated metal. The load-extension curves were the same at the

Jan 1, 1962

By J. H. Lightfoot, Stuart E. Buckley

DEEP drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.1 The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen4,5,6 and by others,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems.9-17 It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 lb. per sq. in. Thus, at pressures of 2500 lb. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 600°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduction. The combined effects of pressure and temperature on condensation and vaporization of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpretation of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate systems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21.22 it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has

Jan 1, 1941

By A. B. Young

THE difficulties encountered in the preparation of. the lead smelter charge for the blast furnace and in the roasting and sintering of the ores, and the expert means taken for the preparation of these materials since the introduction of flotation concentrates into the lead smelter charge, have been described by W. H. Eardley1 and R. A. Wagstaff.2 FUNCTION OF ROASTERS AND BLAST FURNACES The lead smelter has first its roasters and its sintering devices, of which the primary object is the removal of sulfur from the ore or from the charge. The blast furnace follows; its function being the elimination of the gangue material left in the charge-the elimination of the insoluble, the iron, the zinc and the lime from the metallic lead. The secondary object is the separation of copper from the lead. A lead blast furnace is a sensitive apparatus. The materials composing the charge must be marshalled inn certain proportions before they will, make a fluid slag which will separate from the metallic lead. The silica, iron, lime and zinc must be put together in proportions that usually do not exist naturally in the ores, therefore fluxes are necessary. FUNCTION OF THE FLOTATION CELL The flotation cell-speaking from the standpoint of a lead concentrate-has taken over part of the work hitherto performed entirely by either gravity concentration or the lead blast furnace. It has eliminated gangue from the concentrate and separated waste products from the lead. In so far as it has done that, it has usurped some of the function of the lead blast furnace; and it is much cheaper to run a flotation cell than a lead blast furnace. The effect in Utah, and it will be similar to effects in other districts, has been to remove a great deal of the gangue by means of flotation, whereas in the old days it was eliminated by means of smelting. In this district, as in others, the insoluble content of the ores has been greatly out of proportion to the iron and lime content to make a proper slag

Jan 1, 1928

By I. H. Pratt

The results of a study on the preparation of thin-film capacitor structures are discussed. The dietectric source material was quartz which was sputtered and deposited onto aluminum electrodes and counter-electroded to complete the metal-oxide-metal structures. This configuration was utilized to evaluate the dielectric, the device characteristics, and related process parameters. The effect of gas sputtering pressure, magnetic field strength, source-to-substrate distance, and power density on the rate of deposition is shown. Increased film thickness uniformity over a 3 by 3 in. area by optimum substrate positioning is indicated. Dielectric constant, dissipation factor, dielectric breakdown strength, insulation resistance, heat treatment, capacitance, and dissipation over the range 400 Hz to 5 MHz are reported. In the fabrication of silicon-integrated circuits, silicon dioxide has found use as a material suitable as a diffusion mask, for surface passivation of the silicon, and for protection of conductive films used for interconnections. Its use as a dielectric for thin-film capacitors in film hybrid circuits has been limited, to a degree, for lack of a compatible processing technique and because of its relatively low dielectric constant. With the recent advent of practical metal-oxide-semiconductor (MOS) field effect devices, the material is now being used to insulate the gate electrode from the conducting channel in the silicon. In this latter application, more stringent requirements have been imposed on .the oxide. A comprehensive resume of the use of silicon dioxide in integrated silicon device technology has been compiled including oxide film and bulk properties, method of oxide formations, and their applications.&apos; A relatively new process to deposit SiO, and other dieIectrics is by rf sputtering, and the purpose of this paper is to describe the behavior of capacitors fabricated with a dielectric which has been sputtered from a quartz target and to indicate the relative effect of several of the process parameters on the film deposition. Work on rf sputtering of SiO2 and other dielectrics has been reported utilizing a triode type of sputtering system as described herein or a diode self-sustained glow discharge system. 2-8 SPUTTERING The process occurs during an electrical discharge in a gas plasma which provides the ions for acceleration to the target to produce the desired sputtering. The necessary plasma can be generated by a dc glow discharge through application of a high potential between two electrodes at approximately 2 to 10 x 10-2

Jan 1, 1969