Search Documents

By Frank R. Milliken

Before the rather sudden economic downturn in recent months, shortages of materials were painfully felt throughout the US. The current recession has provided a temporary relief here and there-but energy fuels and a number of staples such as sugar are still in short supply. This is an unsolved and fundamental problem that will haunt us again as the economy turns up. There is an awareness that the nation faces a widening supply gap in many of its most basic materials-from asbestos to tungsten-as evidenced by recent studies and government reports, and by the Secretary of the Interior's annual warnings about the mounting seriousness of the problem.

Jan 3, 1975

By Henry R. Piehler

Continuous seven- and nine teen -filament close-packed silver-steel filamentary composites mere tested in tension. For purposes of comparison, the tensile behavior of the composite was predicted from the measured properties of the individual com-ponents. It was assumed that the axial strain is the same in both components and that the contribution of each component to the composite flow stress is proportional to its volume fraction. Good agreetnent was obtained between the observed and predicted tensile behavior. However, the composite elongation at fracture was about twice that observed when the individual steel wires were tested alone. Composites in which the filaments were widely spaced failed by the consecutive fracture of the filaments. In composites with closely spaced filaments, a composite instability preceded frachcre. These effects are explained in terms of a lateral restraint to the necking of the filaments which develops in the deforming composite. TWO-COMPONENT or composite materials are increasingly being developed and used as structural materials. Of all the composite geometries used, the filamentary configuration has proved to be the most successful. Polymer-bonded fiber-glas, the most common of the filamentary composites, has been investigated most extensively to date. One explanation of the behavior of fiberglas1 suggests that the load transfer between the glass fibers and the polymer matrix occurs primarily through friction. Bond separation between the fibers and the matrix is presumed to occur at very low stresses. Subsequently, only frictional bonding can provide for the transfer of load from the matrix to the fibers. The force normal to the fiber-matrix interface which gives rise to this friction is assumed to arise from the matrix shrinkage which occurs during solidification. The behavior of metallic filamentary-composite materials would be expected to differ from that of fiberglas in several significant aspects. Residual stresses resulting from differences in thermal contraction can be kept to a minimum by proper heat treatment. A strong wetted bond is formed between the two phases. In brazed joints,2 for example, the interphase bond is sufficiently strong that the weaker material will fail before separation occurs at the interface. Most metal filaments can undergo appreciable amounts of plastic deformation before failure. Failure by plastic instability or necking frequently occurs in metallic filaments, but not in glass fibers tested at room temperature. Differences between the behavior of fiberglas-polymer and metallic filamentary composites have indeed been observed in composites containing various types of metallic filaments in a silver matrix.3,4 At strains of the order of 10-2 pct, all the deformation was accommodated by the silver matrix. Hence, the strength of the composite depended only on the fiber concentration and not on the nature of the fiber. At higher strains, the strength of the composite increased when filaments with higher work-hardening rates were used. Surface slip line observations on a silver-mild steel composite that had been stretched 4 pct showed that an appreciable amount of deformation occurred in the filaments. Work on tungsten-copper filamentary composites5 has shown that the ultimate tensile strength for varying filament fractions followed a linear mixture rule. Assuming that the axial strains in both filaments and the matrix are equal, this linear mixture rule can be expressed as: The subscripts c, f, and m refer to the composite, filaments, and matrix, respectively. A and V are the area and volume fractions of each component. sc and of are the ultimate tensile strengths of the composite and the filaments. sm is the flow stress of matrix at a strain equal to the elongation at failure of the filaments. However, the tungsten filaments can undergo only a limited elongation before they fracture without an appreciable reduction in area. A composite containing more ductile filaments might indeed deviate from this linear mixture rule for the ultimate tensile strength, since filament failure by necking might be arrested by the matrix. SPECIMEN PREPARATION Specimens were prepared from 0.8 pct carbon steel piano wires of 0.015 in. initial diameter. The wires were given a thin nickel flash and a silver plate varying in thickness from 0.015 to 0.007 in., depending on the filament fraction desired. In order

Jan 1, 1965

By Oscar M. Kucus

In January and February of the current year, at the Tooele plant of the hternational Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of rever-beratory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it mas planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary to install a bag house, a fan, and the necessary flues to complete the equipment. The bag house constructed has a bag-cloth filtering area of 136,000 sq. ft., provided by 960 fume bags, 18 in. in diameter by 30 ft. in length. A No. 20 Sirocco fan of 180,000 cu. ft. capacity delivers the gases from

Jan 1, 1915

By AIME AIME

SIR HENRY CORT HAROLD CARPENTER, great-great-grandson of Henry Cort, famous as the initiator of iron puddling some 150 years ago, carries on the tradition of an illustrious name. Newest of those elected to the Institute's roster of Honorary Members, Sir Harold is distinguished for his achievements in the field of metallurgy as an investigator, teacher, administrator, organizer, and director of research. His interests in research have been in both the ferrous and non-ferrous fields. His name is particularly honored in its association with the establishment of fundamental con¬stants and of critical ranges of iron and iron alloys, and with original and fundamental studies of the preparation and properties of metal single crystals.

Jan 1, 1938

By P. Chiotti, G. R. Kilp

IN the study of zinc-zirconium1 and zinc-uranium2 systems, vapor-pressure measurements were made in order to establish the equilibrium phase diagrams for a pressure of 1 atm. In each of these systems, only zinc has an appreciable vapor pressure over the temperature range investigated. The zinc pressure was measured over a sufficiently wide temperature and composition range to permit calculation of the standard free energy, enthalpy, and entropy of formation for the compounds ZrZn, ZrZn2, ZrZn3, ZrZn6, ZrZn14 , and U2Zn17. In these calculations the compounds were treated as line compounds. Although the exact composition range was not determined, metallographic and thermal data indicate that the solubility range for these compounds is small. It is to be noted that the compound initially reported to correspond to the formula UZn9, 2 has been shown by the crystal structure work of Makarov and vinogradov3 to correspond to the formula U2Zn17,. The crystal structure is similar to that for the compounds Th2M17, investigated by Florio,4 et al; here M represents iron, cobalt, or nickel. Therefore, thermodynamic calculations are based on the formpla U2Zn17 EXPERIMENTAL The dew-point method employed to measure the vapor pressure of zinc over uranium-zinc alloys has been described previously.2 The same procedure and apparatus were used in measuring the zinc pressure over zinc-zirconium alloys. In the case of alloys in the two-phase region consisting of a zirconium and the compound ZrZn, the Knudsen effusion method was employed to obtain a few values in the temperature range 600" to 560°C. In most cases, tantalum crucibles were used to contain the zirconium alloys. THERMODYNAMIC PROPERTIES OFU2Zn17 A least-squares treatment of the vapor-pressure data obtained for 35 and 65 wt pct U alloys in the temperature range 650° to 940°C gave lOg10PAtm = 7,713/T + 6.33 Here, as in following equations, T represents degrees kelvin and P represents the zinc vapor pressure in atmospheres. The probable errors for the two constants were calculated to be 60.68 and 0.0563, respectively. This relation represents the equilibrium dissociation pressure for the reaction U2Zn17 (s) - 2U(s) + 17Zn(v) The solubility of zinc in solid uranium is negligible and the only additional information required to calculate the free energy of formation of U2Zn17 is the free energy of vaporization of pure zinc. K. K. Kelley5 gives the relations, AF°= 30,902 + 6.03Tlog T + 0.275 X 10-3T2 - 45.03T

Jan 1, 1961

By E. N. Mazza, H. S. Kalish

The effect of sintering types 302, 3028, and 430 stainless steel powder compacts in hydrogen and dissociated ammonia was investigated. It was found that sintering in dissociated ammonia resulted in as much as 0.5 wt pct increase in the nitrogen content of stainless steel even though the dissociation of the gas was complete. Sintering in hydrogen, on the other hand, reduced the nitrogen content of the stainless steel to less than 0.01 wt pct. In the case of the 302-type stainless steel, the low nitrogen content resulted in a material that was largely ferritic, whereas the high nitrogen content rendered the material fully austenitic. Sintering in dissociated ammonia resulted in lower density, generally lower tensile strength, less ductility, and higher hardness than sintering under equivalent conditions in hydrogen. The reduction of oxides on both stainless steel and iron particles was found to be effected by hydrogen partial pressure in the sintering atmosphere. Compacting pressure was found also to effect oxide reduction during sintering. DISSOCIATED ammonia often is used as a substitute'.' for hydrogen in sintering and in annealing, since economic advantages sometimes can be obtained by such a substitution. In addition, anhydrous ammonia contains very little impurity. Thus, dissociated ammonia gas is very dry whereas tank hydrogen often must be freed of oxygen and water vapor prior to use in many applications. The sintering of stainless steel powder compacts as well as bright annealing is well recognized as requiring a hydrogen atmosphere and for the foregoing reasons dissociated ammonia is frequently substituted. It has generally been overlooked, however, that the nitrogen in dissociated ammonia might have an important effect on the sintering process and on the properties of stainless steel compacts. Considered an inert gas in many applications, nitrogen, on the other hand, is very reactive with cer- tain metals. Dissociated ammonia could not be used for hydriding zirconium or titanium. Nitrogen reacts with columbium, tantalum, chromium, uranium, thorium, and many other active metals. Iron and iron-base alloys are, for the most part, inert in nitrogen but there are many borderline cases. It has been reported that stainless steel stabilized with columbium or titanium should not be sintered in dissociated ammonia.3 olybdenum has been reported as reacting with dissociated ammonia to a minor extent.' Although most of the reactions with iron-base alloys are attributed to the action of un-dissociated ammonia and the action of nascent nitrogen, Uhlig4 showed how readily pure molecular nitrogen reacts with and diffuses into 18-8 stainless steel at 1150°C. He also pointed out how readily nitrogen diffuses out of 18-8 stainless steel when heated in pure dry hydrogen, and these thorough investigations on the subject show that commercial stainless steels are nitrogen-bearing, since they are melted in air. The effects of nitrogen in stainless steel, particularly the 18-8 Cr-Ni type, previously have received considerable attention." In 1926, it was pointed out

Jan 1, 1956

It is well to bring before you again the chief purpose of the National Research Council and of this its Division of Engineering, to stimulate others to make researches rather than to make them ourselves, because a given amount of our energy spent in inciting others will accomplish far more than if applied in executing them ourselves. This is because there are scattered through the numberless governmental, educational, and industrial laboratories of the country a very great number of investigators not only capable of being stimulated, but willing to aid in cooperative broadly planned research rather than to follow the haphazard methods of the past. Taken collectively, these laboratories and their personnel can produce an annual crop of knowledge the value of which is of the order rather of billions than of millions of dollars. I invite you to regard this potential product as a crop, to be planned, fertilized, harvested, and distributed with the sane order of statesmanship, the same breadth of view, with which we treat any other great human product or achievement, whether agricultural, industrial, or transportational.

Jan 1, 1919

The most extensive oil shale development program ever undertaken in the United States has been that carried out by Colony Development Operation at Para- chute Creek in western Colorado. Field development goals were completed this spring, with the remainder of the $24 million joint venture program, primarily engineering, environmental and economic analysis, due to be finished by the end of 1972. Upon completion of the overall program, a decision concerning a commercial venture is expected. This program points up the increasing attention being focused on oil shale as a source of crude oil and energy for the U.S. at a time when the nation's supply of oil produced by conventional methods is far from adequate to meet the demand. The oil shale reserves of the Green River formation in Colorado, Utah and Wyoming are the largest hydrocarbon reservoir. The Piceance basin of Colorado, alone, contains some 80 billion bbl of shale oil recoverable by modern methods in reserves more than 30 ft thick and containing at least 30 gal of oil per ton. The U.S. Geological Survey has estimated that the total shale oil reserves of the Green River formation in the states of Colorado, Utah and Wyoming is more than 600 billion bbl of oil in deposits containing at least 25 gal per ton of shale oil.

Jan 10, 1972

By F. E. Bash

IN recent years, there have been a number of experiments conducted to determine the rates of heating and cooling of various sizes and shapes of steel ingots. Up to date, however,-most of the published data has dealt with small sized ingots, the largest being an 18-in. (46 cm.) cube, the data on which was presented before the Iron and Steel Institute in May, 1918, by E. F. Law. It is due to thus lack of information on the rate at which large ingots absorb heat and come to temperature that the heating- practice varies so widely in different plants. One of the questions over which there is much debate is the proper rate of heating of large ingots for forging and the time actually required for the center of a mass of steel to come to forging temperature. As a continuation of experiments described by M. E. Leeds1 and at the request of Mr. G. R. Norton of the Sizer Forge Co. and Mr. R. C. Drinker of the Emergency Fleet Corpn., the test described in this paper was carried out on a 24-in. (61 cm.) round ingot and the rate of heating and cooling determined under regular production conditions. The ingot had been partly forged at one end but, on developing a flaw, had been scrapped so that it was available for test. The size and shape of the ingot and its position in the furnace are shown in Fig. 1.

Jan 9, 1919

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS,* LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen's articles and work at the Dutch State Mines exhibited its possibilities in the bene-ficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. l,2,3,4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations.M Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids. While the three applications have been indicated to be feasible, only a meager amount of data is available on capacities and solid elimination eficiency as a function of design variables and cyclone friction loss. This information is essential for the optimum use and construction of the solid-liquid cyclone, and accordingly, work on the problem was initiated at Northwestern University. For the unfamiliar reader, briefly the cyclone consists of a cylindrical section mounted above a truncated cone. The feed nozzle enters the cylindrical ring tangentially with the underflow nozzle permitting discharge of the concentrated solids located at the apex of the cone. The overflow nozzle through which the clarified water exits is centered in the cylindrical section at the top of the cyclone. Half sections of experimental cyclones will be found in Fig la and 6. The feed slurry enters with a tangential velocity, thus creating a spiral pattern of high centrifugal force. The solid particles of sufficient size and gravity are ejected outward to the walls and spirally discharge to the underflow. Most of the water with uneliminated fine solids moves radially inward along the path of the outer

Jan 1, 1950

By T. D. Thomas

CONTENTS PAGE T. D. Thomas-Misfires in Anthracite Coal Mines 3 W. H. Forbes-Misfires in Bituminous Coal Mines 12 A. W. Worthington-Misfires in Non-metallic Mining (Limestone) 18 Misfires in Anthracite Coal Mines BY T. D. THOMAS, * LANSFORD, PA. (New York Meeting, February, 1929) IN THIS paper, major attention is given to misfires in mines where electric multiple shot-firing is the system used. Misfires are sometimes caused by one action or condition and at other times by a combination of two or more. They may be divided into two classes: (1) those caused by workers in the mines, (2) mechanical or manufacturer's causes. The second cause will be discussed first.

Jan 1, 1929

By AIME

VERSATILITY is perhaps the outstanding characteristic of the subject of this sketch. He is author, golf-player, musician, public speaker, philatelist, German scholar, and has been a school teacher; but these are incidental. Oliver Ralston's professional forte might be described as beneficiating solid minerals and he has dealt in an important way with practically all of them. To this work he has brought a fertile mind stimulated by keen imagination but kept on the track by a sense of economic balance. An indication of his versatility is evidenced by his career with the Bureau of Mines, which he first joined in 1912, when the Bureau was just one year old. Except for two excursions into industry-Hooker Electro Chemical Co. (1917-20) and United Verde Copper Co. (1928 to 1935)-his entire professional career has been with the Bureau.

Jan 1, 1946

By Pierre R. Hines

Diphenyl guanidine is used as an accelerator in vulcanizing rubber. Other rubber accelerators are also flotation collectors, e.g., dithiocarbamate, thiazole, and the xanthates. Urea and its derivatives are good flotation collectors,1 and guanidine is the nitrogen analog of urea. These two characteristics suggested testing diphenyl guanidine as a flotation collector. Diphenyl guanidine has been tried in flotation work previously, but references give no details.2-4

Jan 2, 1959

By W. C. Knopf, I. M. LaBaron

In the Carlsbad area potash is dry-mined and wet- concentrated. Wet concentration involves recirculation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KC1. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report.

Jan 10, 1958

By William J. Bronkala

Magnetic Separation is a proven means of effectively obtaining purification and/or concentration of mineral products. In addition, magnetic separators are widely used for tramp iron removal in the protection of mineral processing machinery such as crushers, conveyors, mixers, etc. This paper summarizes the various types of magnetic separators available and outlines their basic selection and usage. Current magnetic separator costing is provided for general guidance and estimating.

Jan 1, 1978

By John L. Baum

Tests show that 50 times the earth's normal field can exist near stacked drill rods. Protection against the effect of these strong fields can be obtained by means of a removable sleeve of common iron pipe. GEOLOGISTS and engineers working around a diamond drill rig have often had the opportunity to observe the magnetic attraction of drill rods pulled out of the hole for core removal. This is sometimes an amusing pastime, but this same magnetic force inadvertently applied to a compass needle can cause it to lose its polarity entirely or to become reverse polarized when placed in the immediate vicinity of stacked rods. The first recommendation, of course, would be to avoid the rods, but in surveying an operating drillhole this is not always possible; therefore steps must be taken to neutralize the magnetic effect of the drill rods. Early in the summer of 1949 the geological department of the New Jersey Zinc Co. undertook at Franklin, N. J., an extensive program of surveying the course of deep diamond drillholes. The majority of the holes were surveyed while in the process of being drilled, and considerable difficulty was encountered. A pattern for the deviation of drillholes had been established for the district from surveys in holes from which the drill rig had been removed. It was observed that a certain operating deep drillhole being surveyed did not fit this pattern. In the resulting confusion of repeated surveys and cementing a plug for wedging operations, the lower 1800 ft of the hole was lost. Because of this incident studies were initiated to determine the source of the difficulties and to develop safeguards against recurrence of faulty surveys. Using a hand magnet easily shows that the polarity of a compass needle can be reversed if rotation of the needle is hindered through tilting of the compass or clamping of the mechanism. Such experiments are not recommended, especially in the case of the clockwork type of instruments. A magnetized hairspring in a clockwork instrument will cause the compass card to assume a periodic motion which will not stop until the clockwork runs down. Routine check readings of instrument north before and after each survey are not always sufficient to catch instances of reversed polarity of the compass needle. Although the majority of instances probably take place while the instrument is being removed from the hole with needle in fixed position, it is demonstrable that a 'luggish needle, weakened during a previous test, can be reverse polarized

Jan 1, 1955

By W. J. Keep

Some explanation of methods of testing will be given before presenting the record of a series of physical tests of aluminum, other metals and alloys. I. The Methods Employed and Meaning of Diagrams. The test-bars used, 12 inches long and 4 inch square, are cast in green sand, with chills bedded in such a way that the ends of the bar run against them. By splitting the ends of the bar the depth of chill can be measured. The chills being held in the mould 121/8 inches apart, the space between the end of the bar and the face of the chill, after both are alike cold, is the amount of shrinkage, and is recorded in thousandths of an inch per foot.

Jan 1, 1890

By T. L. MacKay

Oxidation rates of single-crystal and poly crystalline zirconium in oxygen at temperatures from 307° to 815°C obey the parabolic rate law for short ex-posure time, 4 to 6 hr. The activation energy for the oxidation of single-crystal zirconium between 420° and 790°C is 42.6 ± 0.7 kcal per mole, and in the temperature range 307" to 600°C the activation energy for oxidation of poly crystalline zirconium is approximately the same. The high-activation energy is indicative that diffusion through the bulk oxide film is the primary mode of mass transport for both types of metal. The higher oxidation rates for poly -crystalline zirconium in this temperature range were attributed to differences in the orientation of the grains in the metal with respect to the oxidizing surfaces. Above 600°C, vain growth was observed in polycrystalline zirconium, and the oxidation rates approached those of single-crystal zirconium. ThE kinetic data of previous oxidation studies1-' of zirconium in oxygen have been interpreted by both parabolic and cubic rate laws. There is some evidence that there is a transition from the parabolic to the cubic rate law at prolonged exposures, but the question is still controversial. For the parabolic rate law activation energies are reported in the range 18.6 to 35 kcal per mole, and for the cubic rate law in the range 38 to 47 kcal per mole. So far as the mechanism of zirconium oxidation is concerned, inert marker studies10,11 have indicated that the oxidation proceeds by oxygen (anion) diffusion through the oxide film toward the metal-metal oxide interface. Pemslerl2 observed that the orientation of the grains in the zirconium metal substrate affected the rate of formation of the oxide film on the surfaces of the grains and that the orientation dependence of the corrosion rate persisted beyond the initial stages of reaction. The rate of oxidation was a minimum when the c axis of the grain was parallel to the surface of the sample, and rose to a maximum when the c axis was inclined at about 20 deg to the plane of sample surface, and decreased again at higher inclinations. cox13 observed that in 300°C steam a thin oxide film was formed initially on zirconium and that this oxide film, which exhibited interference colors, became dark first along the grain boundaries and then over the whole surface in an inhomogeneous manner as the film thickened. Cox proposed a mechanism in which oxygen diffused along preferred paths created by grain boundaries in the metal and formed a much thicker film at or near the grain boundary than on the central zone of the grain. In the present study, the oxidation rates of single crystals of zirconium were measured in oxygen and compared with the oxidation rates of polycrystalline zirconium of the same bar stock. It was felt that such a comparison would elucidate the role of grain boundaries in the metal substrate. SAMPLE PREPARATION Single crystals of zirconium were prepared by following the procedure of I3apperport,14 starting with 1/4-in. rod purchased as crystal-bar zirconium. Zirconium rods 2 in. long were wrapped in tungsten foil and sealed in quartz tubes at pressures of less than 10-6 mm of mercury. Large single crystals were grown by thermal cycling above and below the a-/3 transformation temperature, 862°C. Several specimens were simultaneously subjected to the same cycling procedure, heating to 1200°C, holding for 4 hr, then cooling in the furnace and holding at a temperature of 840°C for 5 to 10 days. This cycle was repeated five or six times for each set of specimens. The grain size of the crystal-bar zirconium before thermal cycling was between 10 and 30 p. Fig. 1 shows the microstructure of an end section of as-received crystal-bar zirconium. A longitudinal section of each zirconium rod after thermal cycling was polished and examined under polarized light, see Fig. 2, and the largest single crystals were selected for this study. Zirconium rods 1/8 in. in diameter and 1/2 in. long with spherical ends were machined from the single crystals and from the as-received bar stock. An X-ray examination showed that the c axis of the single crystals made either a 34-deg or an 89-deg angle with the rod axis. The specimens were chemically etched for 2 min in solution consisting of 15 parts hydrofluoric acid (48 pct), 80 parts nitric acid, and 80 parts water. The chemical polish removed 1 to 2 mils from the surface. EXPERIMENTAL The Sartorius vacuum microbalance used in this study has a sensitivity of 0.5 pg and a capacity of

Jan 1, 1963

PRIOR to the World War most of the barite used in the United States for manufacturing lithopone and barium chemicals was imported. Germany, by virtue of an abundance of high-grade ore and low labor costs, was in a position to dominate the world market. With the cessa-tion of imports and with the war demand for barium chemicals, the barium chemical industry and the mining of barite became well estab-lished in the United States. This industry has continued to expand because of the increasing use of lithopone. In 1914 the sales of domestic crude barite was 52,919 tons and in 1934 it was 209,850 tons. Barite deposits of economic importance occur in at least 20 states, but the principal producers in 1934 were Missouri, Georgia, Tennessee, South Carolina, Virginia, California and Arizona. The main mining centers are located near the crude barite markets of the three principal marketing districts-the Pacific Coast, the Midwestern area, and the Eastern area. The Pacific Coast is supplied entirely by California, Nevada, and Arizona. The Midwestern area uses most of the Missouri crude and a small amount from the southern states. The eastern market is the chief competitive area. Practically all of the imported crude is marketed there; also the bulk of the southern crude and ground barite. In addition, this area absorbs a small part of the Missouri crude and 80 per cent of the ground barite. Besides the advantage of low delivered costs and purity of product, the imported barite has commanded a price differential because it is soft rather than hard, like many of the domestic ores. The inherent physical properties of the southern ores remain, but the purity can be controlled to a great extent by beneficiation. Simple washing or gravity concentra-tion has sufficed in the past, but in many cases a more efficient process now becomes imperative to remove impurities not amenable to these methods. Certain deposits now being opened are of lower grade and require more precise milling conditions. In some ores, the kind of impurities has changed as the mining advanced.

Jan 1, 1936