Search Documents

By Ben L. Seegmiller

Artificial support of rock slopes in mining applications may consist of rock anchors with and without auxiliary support systems, but- tresses or shotcrete. The use of artificial support systems is not applicable in all cases of slope instability. Some pit slope problems simply cannot be cured with a support system. In other cases, a sup- port system which would solve the problem would be uneconomical. Rock anchor design may be undertaken using an active or tensioned system or a passive or untensioned system. Failure problems to which artificial support systems are most commonly applied include planar, wedge, rotational and toppling failures. Design of auxiliary support systems and rock anchor peripheral items may be initially estimated using analytical concepts, but field trials are commonly used to determine final requirements. Field procedures usually require a close coordination between mining personnel and the support installation team. Great care must be exercised during installation to prevent numerous potential problems including poor anchorage, excess bearing and corrosion. Displacement monitoring of the completed system is a must if the effectiveness is to be closely judged by means other than total slope and/or support system failure. The cost of a support system is relatively high when compared to other remedial measures that may be taken to solve a slope instability problem. Therefore, the system costs play a vital role in determining whether or not artificial support should be considered beyond the initial assessment stage. Case histories are few, but do include examples of each type of support system.

Jan 1, 1983

By D. H. Henley, F. F. Craig, W. W. Owens

The oil recovery performance of systems producing entirely by bottom-water encroachment has been experimentally determined in a series of scaled laboratory-model tests. The effects of well spacing, fluid mobilities, rate of production, capillary and gravity forces, well penetration and well completion techniques on the oil recovery performance have been investigated. The laboratory tests were performed using two uniform, un-consolidated sand-pack models. The models have ratios of the interwell distance to the formation thickness of 12 and 2, respectively. Tests at constant total fluid production rate were performed simulating a range of uniform reservoir characteristics and operating conditions encountered in field operations. The performance was determined by material balance and by observation of the encroachment of dyed fluids into the models. The results of the model tests agreed with those obtained mathematically when the conditions previously considered in theoretical studies were simulated, that is, when the oil and water are of equal density and no capillary forces exist. The model study of bottom-water drive indicated that certain variables can aoect the oil recovery performance to a greater degree than can be predicted by present analytical methods. In one comparison, the oil recovery at a water-oil ratio of 20 (obtained at a wide well spacing) varied as much as threefold, depending upon the system's properties and the production rate. Lesser effect of mobility ratio and no eflect of capillary forces over the range studied were observed. The test 'results also showed that the deeper the well penetration into the oil column, the greater the total water production to a producing WOR of 20. However, the ultimate sweep efficiency, and so the oil recovery to this level of WOR, did not vary significantly with well penetration. Horizontal fractures at the top of the formation did not significantly change the sweep characteristics of the reservoir models when values of radius and fracture capacity encountered in actual reservoirs were used. Impermeable pancakes at the bottom of the well moderately increased the oil recovery efficiency both at water breakthrough and at high water-oil ratios. A method is outlined by which the oil recovery performance of other uniform bottom-water drive systems can be estimated from the information obtained in these model tests. INTRODUCTION When oil is produced from a well which partially penetrates an oil zone completely underlain by water, the water rises directly beneath the well in a symmetrical cone when the system is uniform. Two different flow mechanisms can cause the water cone to form—coning and bottom-water drive. In coning, the aquifer is relatively inactive and the cone is formed beneath the well by the pressure gradients associated with the oil flow to the well. The oil can be produced by a solution-gas drive, an edge-water drive or other driving forces in the interwell area. In a bottom-water drive, the driving force for oil production comes from an upward encroachment of the underlying active aquifer. Two papers have analyzed the theoretical performance characteristics of bottom-water drive reservoirs. In the initial mathematical investigation, Muskat' established the equations which determine the pressure distribution in this type of reservoir and solved these equations for certain conditions. Specifically, it was assumed that the water and oil had equal mobilities and equal densities, there were no capillary forces, the pressure throughout the oil zone remained above the bubble-point pressure, a constant pressure existed at the initial water-oil contact and the oil was completely displaced by the encroaching water. These assumptions were used in obtaining analytical solutions. In general, Muskat found that the sweep efficiency to initial water breakthrough to the well was larger for the thicker oil zones, the closer well spacings, the lower ratios of vertical to horizontal permeabilities, the smaller the penetration of the well into the oil zone and the smaller the bore size of the well. The production history after water breakthrough was expressed as a volumetric sweep efficiency at a given producing water-oil ratio. The results indicated that cumulative oil production at producing water-oil ratios of 10 is less affected by the well spacing than is the water-free production history. Muskat studied well spacing which today would be regarded as close. The maximum value of his dimensionless well spacing (ratio of interwell distance to formation thickness) was 4.3. This would require the development of a 50-ft-thick oil sand on less than 10-acre spacing if the vertical and horizontal permeabilities were equal, with

By Edel Moldenke

Burma has long been known for its ruby, tungsten, and tin deposits, and, lately, for having the largest lead-zinc mine in the world, the Bawd-win mine of the Burma Corpn. All the coal used, however, is imported from Calcutta; this is a bituminous coal of about 11,000 B.t.u., 24 per cent. ash, and costs about $8 per ton. Bituminous coal has not, thus far, been found, but many lignite deposits are known. The most promising lignite deposits are in the Namma field, Fig. 1, situated in the Northern Shan States of Upper Burma, about 30 mi. south of Lashio, the terminus of the Burma Railway, 750 mi. north of Rangoon. The

Jan 1, 1922

By Joseph R. Hatch

When compared to average shale composition, average coal is enriched in sulfur and selenium, has similar amounts of arsenic, beryllium, lead, antimony and molybdenum, and is depleted in at least 26 other elements. Within a coalfield, or region, some coals are enriched (10X average shale) in silver, arsenic, cadmium, cobalt, germanium, molybdenum, nickel, lead, selenium, uranium, and zinc. Important factors controlling element distributions in coal include geochemical conditions (primarily pH) in the peat swamp, composition and depositional environment of coal roof rocks, thermal maturity (rank), nature and intensity of any epigenetic mineralization, composition of ground waters that come in contact with the coal, and degree of weathering.

Jan 1, 1983

By Edward F. Divers

Face ventilation is generally the most critical area in the coal mine ventilation system. Various studies have repeatedly shown that good ventilation is by far the most effective and least costly method of controlling dust and gas problems created during face operations. The Bureau of Mines has recently developed and assisted in the development of several new concepts in face ventilation systems, and in methods to accurately evaluate these systems underground. A new type of scrubber and ventilation system design built into the auger support frame of a continu- ous miner was developed. The objective was to improve face ventilation and reduce respirable dust concentrations. With this arrangement, one scrubber is mounted into each side of the boom. Laboratory and underground tests of various scrubber discharge arrangements showed good to excellent dust and methane control. Combined face ventilation systems, using both blowing and exhaust curtain, potentially offer dust and gas control and deeper cutting. Bureau tests at a mine using a combined face ventilation system and remote- control-operated continuous miners showed excellent dust and methane control. The advancement of line curtain systems beyond permanent supports without exposing workmen to roof fall hazards can be accomplished only with specially designed extendable devices. Numerous concepts for line curtain extension have been developed and tested. For the past several years, the Bureau has been testing various types of extensible face ventilation systems. These extensible systems can generally be classified as floor-, roof-, machine-, and rib-mounted systems. In the past 6 years, approximately 40 systems have been evaluated for feasibility. From these, several have been selected as practical or innovative and are presented herein. A technique developed by the Bureau to accurately and safely evaluate the effectiveness of face ventilation is also presented.

Jan 1, 1982

By A. W. Schlechten, Ernest J. Breton Jr.

Experiments on the separation of copper and zinc ions by selective action of ion exchange resins showed the carboxylic type to be more effective than the sulphonic resins. The latter demonstrated a greater capacity over a wider pH range. Data show the effectiveness of resins as a means of concentration. IN recent years the restrictions of stream pollution laws and the high price of metals have created an interest in ion exchange as a means for metal recovery. Some applications have proved successful. In Germany during World War 11, 17 tons of copper per day were recovered from rayon mill wastes by means of ion exchange resins;' and for some time in this country a large ion exchange unit has been in operation for the recovery of copper from rayon waste water. The possibilities of applying ion exchange to the recovery of metals occurring in plating rinse water is particularly promising. In most of these applications only the metal being recovered occurs in the waste. The ion exchange resins act merely as a means of concentrating the metals to a point where they can be recirculated. It would be highly desirable to use ion exchange as a means of not only concentrating but also of separating metals. With the exception of the impressive separations accomplished in connection with the atomic energy program, very little has been done on metal separations.' Therefore, an investigation was undertaken at the Missouri School of Mines and Metallurgy to determine if either of the two main types of ion exchange resins could be used to separate metal ions in solution. The selective removal of copper ions from a mixture of copper and zinc on carboxylic and sulphonic-type resins was investigated as a function of flow rate, pH, copper-zinc ratio, and concentration. It was shown that zinc can be separated from copper and that very large ratios of concentration can be obtained using ion exchange resins. Since ion exchange is relatively new to the field of metallurgy, a brief review of the subject will be included. Theory of Ion Exchange A comprehensive theory for ion exchange has not been developed as yet, but the mechanisms are analogous to metathetical reactions: R Na + Cu++ *=? K(SO3)2 Cu + 2Na+ R is the designation for the ion exchange resin. If a copper solution is passed over a resin bed in the sodium form, two ions of sodium will be released for every ion of copper removed. For the most part this reaction follows the laws of mass action and of electrical neutrality. Consequently, if an excess of sodium ions is passed over a bed containing copper, the reactions will be reversed, and the resin will be regenerated to its original form. A few empirical rules governing the exchange reaction have been set forth: 1—In general ions with a high valence will replace ions with a lower valence. 2—Ions having higher activity coefficients have a higher replacement potential. 3—In a series of mono-valent ions, those with the smallest radii of hydra-tion will tend to replace those having larger radii of hydration. 4—Where ions are similar in most respects, those with the higher atomic weight sometimes will take precedence. This last rule is not as definite as some of the others. These rules apply to rather dilute solutions at moderate temperatures and assume all ions to be present in about equal concentrations. Higher concentrations and temperatures may in some cases reverse the normal exchange reactions. Ion exchange materials are unique in that their efficiency increases as the concentration of the solution decreases. For many exchangers, most efficient operation is obtained at concentrations in the order of one thousandths of a percent. Most applications, though, are made in solutions containing considerably higher concentrations than this. Coste9 as shown that ion exchange resins will remove aluminum and iron effectively' from solutions of up to 10 pct chromic acid. Ion Exchange Resins Ion exchange resins are insoluble, porous, resinous structures to which active groups have been attached. Active groups such as (—SO,,)- and (COO)- pick up cations; hence structures saturated with groups such as these are called cation exchangers. Structures saturated with groups such as (—NH,)' which pick up anions, are referred to as anion exchangers. The resinous structure of necessity is resistant to strong acids, bases, oxidizing, and reducing agents, and most of the common organic solvents. An idea of the stability can be gaged from the fact that resins last for many years under constant use without detectable chemical or physical breakdown. The ion exchange reaction is not confined to the surface of these synthetic resins. Its porous structure permits active groups in the center of a particle as well as those on the surface to remove ions. A high capacity resin such as Amberlite IR-120 will remove up to 3.3 lb Cu per cu ft of resin. In this investigation several approaches to the problem of separating copper from zinc by ion exchange were considered. First, if a reagent could be found which would complex one of these metals and not the other, then by passing this reagent through a bed of exchanger containing copper and zinc, the

Jan 1, 1952

By C. G. Albert

The literature of paper technology contains a number of articles having reference to developments in the field of coating and filler clays for use in paper manufacture. Much of this information has not been included in mining publications and has therefore not been readily available to all in the mineral industry. Recent developments in this field, including spray drying of clays, are presented here. U. S. Bureau of Mines figures for 1952 indicate that the paper industry consumes more than 50 pct of all kaolin produced and sold in the U. S. As most of the kaolin used by the industry comes from Georgia producers, the fraction of their output destined for paper use is thus appreciably higher than 50 pct. Small wonder that the kaolin industry, especially in Georgia, is highly sensitive to the quality requirements of paper mills and must respond promptly to technological developments in paper manufacturing.

Oct 1, 1955

By C. E. Mendenhall

THE word temperature has both a colloquial and a technical use. For everyday purposes of abusing the weather man, no very exact definition is necessary, but for the purpose of giving a simple summary of the physical laws that form the basis of practical pyrometry, something more precise is required. Beginning, therefore, with the common concept of "hotness" and "coldness," we must agree on a method of measuring differences in "hotness," on the unit to be used, and on the point from which measurements are to be taken. We shall then have a definite "scale of temperature," which can be used in all methods of pyrometry. But, as in many similar cases, it is much easier to define or describe something than it is to make practical application and use of the definition; so that much of our attention will be taken up with practical methods of realizing or applying the scale agreed upon. It was early observed that changes in temperature produced large and easily measurable changes in gases, which may be most simply separated into changes in volume (expansion and contraction) under conditions of constant pressure, and changes in pressure under conditions of constant volume. These changes are much the same in magnitude for the common gases oxygen, nitrogen, and hydrogen and also for the rarer helium and argon. This relative uniformity in behavior led to the suggestion of "the gas thermometer" and "the gas scale" as the basis for all temperature measurements. However, as methods were refined, differences appeared between different gases and different ways of using gases, so that Lord Kelvin introduced his more fundamental notion of the "absolute thermodynamic scale" of temperature, which he defined as follows: Given two bodies, say two tanks of water, at different temperatures to determine these temperatures on the "absolute thermodynamic," or Kelvin, scale, operate a thermal engine between these two temperatures, letting it take in heat from the hot body and give out heat to the cold, which therefore corresponds to the boiler and the condenser of a steam engine. The engine we may imagine as a cylinder and piston inclosing a gas and operating with the well-known Carnot or isothermal-

Jan 9, 1919

By J. Walter Scott

IT is usual practice in the copper industry to use open horizontal molds for casting tough-pitch copper wire bars.1 A wire bar cast in this manner is partly characterized, by heavy wrinkles and a comparatively deep skin of oxide on the top of the bar, corresponding to the open side of the mold. On the theory that the rough, high-oxide surface might have an adverse effect on the rolling and drawing properties of a wire bar and might account for some of the irregularities of mill behavior, several bars which had been planed to remove the wrinkled surface were processed into wire. These bars responded to mill treatment more satisfactorily than did the regular wire bars. Realizing that machining the surface of one face of each bar would not be commercially feasible, it was decided that casting the metal into a vertical mold and cropping off the pouring end would accomplish. approximately the same result. Several wire bars of commercial size (250 lb.) were so cast and processed into wire for comparative test with bars cast in the usual horizontal molds. It is the purpose of this paper to present the results obtained from this investigation, in which commercial bar sizes and processing technique were used throughout. The results show that in general copper wire bars cast vertically are superior to those cast horizontally.

Jan 1, 1930

By A. D. K. Laird, C. A. Johnson

Drag coefficients for a cylinder being towed through water at constant velocity and also at constant linear acceleration were measured. Drag coefficients for constant velocity towing showed reasonable agreement with previous results. The drag coefficients found for constant acceleration showed little correlation with either the magnitude of the acceleration or the value of the modulus AD/V2 and tended to be slightly lower than those for constant velocity. INTRODUCTION For the design of offshore structures, wave forces acting on immersed cylinders are of importance. Several investigations have been made of these forces and of how they can be predicted from wave theories. A paper by Crooke' summarizes much of the work already done. More recent research by the Wave Research Laboratory at the University of California, Berkeley, has added much to the body of data collected under ocean wave conditions, but has not found a reliable method of force prediction from basic theories of wave motion. The present investigation is part of a long-range program to collect data with which to test current and future theories and correlations. The immediate objective was to measure drag forces on a circular cylinder subjected to linear accelerations over the range of Reynolds numbers between l04 and 105 where the drag coefficient was a constant for constant velocities. In particular, the effect of constant acceleration from rest and from uniform motion was to be investigated. The effect of acceleration may be evaluated in terms of drag coefficients. A useful resistance coefficient, C, is defined by the equation for total drag force, D, exerted by the fluid on the cylinder. DT =CSp V2/2.........(1) The coefficient C may be plotted as a function of the parameter AD/V2. Here D is the diameter and S is the projected area of the cylinder. The acceleration and velocity are A and V. The mass density of the fluid is p. An alternate drag coefficient, C, corresponds to the total force of the fluid opposing the motion minus the virtual mass force. This drag coefficient, arising from the velocity of the fluid, may be compared with that for the same cylinder in uniform motion. The similarities and differences between this coefficient as calculated for accelerated and for steady motion are of interest in the inverse process of predicting drag forces on cylinders under arbitrary conditions. One serious difficulty in this method is the specification of the virtual mass which depends also on the flow picture about the cylinder.1 EXPERIMENTAL EQUIPMENT The experiment was performed in the combination wave and towing tank at the Engineering Field Station of the University of California. The tank is 200 ft long, 8 ft wide, and 6 ft deep. The tow carriage is externally propelled by a cable, and the velocity of the carriage is maintained essentially constant by means of an am-plidyne. For the purpose of the present investigation, the speed control of the amplidyne was modified by inserting a linear speed control rheostat, which was rotated at a constant speed by a small d-c motor equipped with a slip-clutch. Accelerations which were constant over a reasonable length of time were thus produced. The magnitude of the acceleration depended upon the speed of the d-c motor and the limiting speed of the carriage. Data were obtained for a range of accelerations of 2 to 10 ft/sec,2 and a range of velocities of 2 to 15 ft/sec. An accelerometer (Statham Type C-2-350) with a range of ±2g was attached to the carriage and connected to a Brush analyzer and penmotor. A continuous coil of wire with 10 turns/ft wound around a fixed wooden form extending for a distance of 40 ft along the length of the tank was connected by an electrical contact mounted on the carriage to a Brush analyzer and penmotor, to give the time-position history for each run. The test cylinder was machined from solid aluminum alloy, 17-ST. to a diameter of 1.250 in., and could be

Jan 1, 1957

By Mark N. Alling

A few years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 1, 1915

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

By Alexander L. Holley

A CHARACTERISTIC, and, to Americans, an amusing discussion of the three-high rail-mill, arose out of the reading of Mr. Lauth's paper on three-high plate-mills, at the Glasgow meeting of the Iron and Steel Institute. From the report of the meeting in the English papers, it appears that Mr. Menelaus, the celebrated rail-maker of Dowlais, could not wait for the discussion of Lauth's plate-mill, but launched at once into the British objections to the three-high rail-mill, which is quite another matter. The American mill, which is very different in principle and ar288

By S. C. Lee

An uncoupled thermoviscoelastic finite element formulation with an application to Underground Coal Conversion (UCC) is presented. An incremental solution procedure with an implicit time stepping scheme is used under the thermorheologically simple material (TSM) postulate. The presented formulation, for a homogeneous and isotropic medium, is employed in the simulation of the UCC post-burn phase. Temperature, displacement, stress, and failure responses under thermomechanical loading are predicted. The solutions for the selected field problem indicate potential roof collapse, stress relaxation, and modest surface subsidence with a progressive thermal and failure front. The corresponding thermoelastic responses with temperature- dependent elastic properties are also presented and compared with the thermoviscoelastic results.

Jan 1, 1984

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976

By J. W. Downey, R. A. Morris, M. V. Nevitt

An experimental survey has determined the occurrence of Ti2 Ni-type phases in binary and ternary alloys of Ti, Zr, or Hf with first, second, or third long-period transition metals and also in ternary systems in which 0 is the third component. The existence of eleven previously unreported isomorphs is cited and some approximate phase boundaries are given. Lattice parameters are reported for the new phases. The periodic table relationships involved in the occurrence of the phase are discussed. A previous paper' reported the occurrence of a group of Ti2Ni-type phases (structure-type E93) containing Zr in combination with Rh, Ir, and Pt, and Hf in combination with Rh, Pd, Ir, and Pt, and cited evidence to show that all of the Zr phases and the Hf-Pd phase are not binary phases but occur only when 0 is present. More recently one of the present authors found that in the ternary systems of Ti and 0 with Cr, Mn, Fe, Co, and Ni the occurrence of the Ti2Ni-type phase could be correlated qualitatively with valency electron concentration, and that the role of 0 appeared to be that of an electron acceptor.' This paper describes the results of a broader investigation of the occurrence of Ti2Ni-type phases in binary and ternary systems containing Ti, Zr, or Hf. EXPERIMENTAL PROCEDURE Alloys were prepared by arc melting. The purity of the metals Zr, Rh, Hf, Ir, Pd, and Pt was given in the previous paper.' The additional materials used for this work were metals with a minimum purity of 99.9 pct and reagent grade ZrO2, TiO2, Cr2O3, and NiO. Chemical analysis of several alloys in each system indicated good agreement between intended compositions and cast-button compositions. For the heat treatment precautions were taken to avoid oxygen contamination. The specimens were wrapped in Mo foil and sealed in fused quartz tubes at a room temperature pressure of 1 x mm of Hg. These capsules were then annealed in a vacuum furnace at an external pressure of 5 X mm of Hg. Since the major constituent in most of the alloys studied was the brittle Ti2Ni-type phase, Debye-Scherrer patterns with sharp lines could be obtained with powder crushed from the annealed solid samples without being reannealed. Metallographic, X-ray diffraction, and density determination techniques previously described1, 2 were used. RESULTS AND DISCUSSION Zr-Rh-O, Zr-Ir-Oand Zr-Pt-O Systems-Figs. 1 through 3 show the approximate boundaries of the Ti2Ni-type phase fields at the temperatures indicated in the ternary systems Zr-Rh-O, Zr-Ir-O and Zr-Pt-0. In each isothermal section the Ti2Ni-type phase field is labeled E and the unidentified binary phase found in the previous work' is labeled ?. The dotted lines, which are not phase boundaries, correspond to the composition (Zr2 B)1-xOx. In each system the Ti2Ni-type phase field is displaced to the high-Zr side of this composition line. However, the departures from Zr2B stoichiometry for the metal components are not as high as Zr3B, as was inferred from the previous work. Lattice parameters of the Ti2Ni-type phases in the alloys shown as triangular data points in Figs. 1 through 3 are given in Table IA. The probable compositions of the Ti2Ni-type phases have been estimated from the isothermal sections. Although there are a few exceptions that probably result from uncertainties in phase boundary location and from the effect of variation of oxygen content, the generalization can be

Jan 1, 1961

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

By Henry Hibbard

THE process of making washed metal now followed is in principle that described by Holley before this Institute in 1879, as the Krupp washing process. Sir Lowthian Bell also experimented extensively in England during 1877 and 1878 on refining iron and joined his interest with Krupp, the process being often referred to as the Bell-Krupp process. The only plant in this country now operating this process is that of the Brier Hill Steel Co., Youngstown, Ohio. This process may be considered as the sole survivor of the numerous methods conceived for refining crude iron, when the removal of phosphorus from steel-making material was the great desideratum affecting large districts. The east coast of England and all northern Germany, the homes of Bell and Krupp, respectively, could at that time make steel only from imported ores. These processes were in use or in various stages of development 40 years ago and all except the Bell-Krupp received their quietus from the development of the basic steel processes, both pneumatic and open hearth. The aim of the early refining processes was, first, the removal of the silicon; which could be clone on a sand bottom, and later, the removal of the phosphorus, requiring a bottom which would give or permit a basic slag. The incidental advantages of increased yield and small fuel consumption were not generally recognized or considered; the aim of the later. operations was the saving of the difference in value between low and high phosphorus irons, as well as hastening the removal of the metalloids. The chemistry of the washing process follows in part that of the puddling process, and indeed washing might, be considered as the first half of puddling, since all the non-ferrous elements of the crude iron, except the carbon, are eliminated and the iron is maintained molten until cast. In puddling, the iron loses its carbon as well, and because of that, its fusion point rises above the hearth temperature; it freezes into a pasty malleable form, and is worked at once by squeezer, hammer, or rolls.

Jan 12, 1915

By John V. Beall

AMONG electrical manufacturers, interest in the outlook for copper supplies has not diminished despite signs of a healthier market following price decontrol. Reason: Electrical utility industry output is expected to grow at an average annual rate of 6 pct for the next 15 years. A more graphic description of the growth ahead is given in the Eighth Quarterly Report of the Director of Defense Mobilization as follows: "Power generating capability, which amounted to 63 million kw at the time of Korea, now stands at more than 81 million. The established goal for installed capability at the end of 1955 is 116 million kw. Orders already on the books of power equipment manufacturers, if fulfilled on schedule, will bring installed capability to over 123 million kw by the end of 1956-and more orders for equipment are yet to come." These statistics portend an impressive requirement for copper, not only for power plants and distribution lines themselves but for the multitude of industry and domestic end-uses.

Jan 4, 1953

By Virgil Miller, F. B. Petermann, S. F. Ravitz

The Cle Elum nickeliferous iron deposit is in Kittitas County, Washington, in a rugged, mountainous region about 23 miles north of the town of Cle Elum. The Biewett Pass deposit, which is similar in character and occurrence, is in Chelan County, about 18 miles east of the Cle Elum deposit. A more or less continuous ore zone may extend between the two deposits, since iron ore is reported to have been discovered at Iron Mountain, which lies directly between them. The ore probably was formed by meta-morphism of laterite resulting from Ieach-ing of serpentine derived from peridotite. It consists largely of magnetite grains distributed through a matrix of limonitic material containing a small amount of hematite and chromite. Many of the chromite grains have shells and inclusions of magnetite. The magnetite grains range in size from 1200-mesh to 1/4-in., the average size being 48 to 65-mesh; the chromite grains range from 20 to 150-mesh. The gangue minerals are olivine and serpentine with a small, amount of chlorite, and appear both as very thin bands in the ore and &apos;s minute fragments in the limonitic matrix. The nickel is present as minUte inclusions of a nickel silicate mineral within the magnetite and gangue par- ticles, varying in size from 1500 to about 280-mesh. Detailed analyses of 3000-lb. lots of Cle Elum and Blewett Pass ore are given in Table I. TABLE i.—Analyses of Ore Samples Per Cent Ore from Constituent cle Elum&apos; Blewett Pass Cr....................... 2.23 2-12 Ni...................... 1.43 0.9s Fe...................... 52.9 41.4 SiOz.................... 5.6 13.4 CaO.................... 0.3 0.8 MgO................... 4-1 7-5 AI2O3................... 7.0 2.g P...................... 0.022 0.034 S....................... O.O1 o.oa Mn..................... I.I 0.4 Ba..................... nil co..................... o.oa 0.02 CU..................... 0.02 0.03 As...................... 0.03 Au..................... nil Ag°..................... O.58 Pt...................... ml Fe++.................... 8.9 5-9 Fe+++.................. 44-0 35-5 « Ounces per ton, 1 sr,cte,so,","&&$ally absent: B, W, M~, T~, V, ~i, Bi, Pb. Sb. Sn. Be, In, Hg. Zn, Zr. Cd. Preliminary Tests Attempts to beneficiate the ore by ore-dressing methods, including various &apos;cornbinations of sink and float, tabling, jigging, flotation, and magnetic separation, were consistently unsuccessful. A wide variety of roasting and leaching tests were made on both raw and reduced ore, but in most of the tests little or no nickel was extracted, and in none did the extraction exceed 50 Per cent. No nickel could be volatilized as the carbonyl. by treating reduced ore with carbon monoxide. Fairly good sepa-

Jan 1, 1944