Search Documents

By R. Janes, F. Everard

Pilot plant studies have been conducted on a variety of iron ores of differing composition and grain size to test their amenability to dry autogeneous grinding and dry magnetic concentration. A general description of the pilot plant and its equipment is given with particular reference to the Aerofall mill and the dry magnetic separators developed by the Ontario Research Foundation. Test results are reviewed in detail with emphasis on power consumption, mill speed, the use of ball charges, types of ores, moisture content, separator speeds, and design. In 1957 the Ontario Research Foundation installed a pilot plant (Fig. 1) for the study of dry autogenous grinding and dry magnetic concentration of iron ores. A 61/2-ft Aerofall mill was installed as the dry autogenous crushing and grinding medium. The Cavanagh fast drum and the Double Helix, two dry magnetic separators developed at Ontario Research Foundation, were also installed. Iron ore samples of 10 to 150 tons have been investigated. These ores varied widely in mineralogy and grain size. Taconite (-325 mesh), fine-grained magnetite (200 to 325 mesh), and medium-grained magnetites (65 to 150 mesh) have been treated with varying degrees of success. Lately, considerable research has also been conducted on the metamorphosed magnetite-hematite complexes of the Labrador Trough. Operational and metallurgical data have been compiled from these tests. The effects of ore type, air flow, mill speed, and ball charge on mill operation are discussed. Metallurgical data are also presented to illustrate the operation of the dry magnetic separators. PILOT PLANT DESCRIPTION Fig. 2 depicts the normal flowsheet used. Minus 6-in. ore from a vibrating feeder is fed to the 6%-ft Aerofall mill powered by a 50-hp 550-v induction motor. The main blower, a 25-hp 550-v fan rated at 7000 cfm, draws air through the mill. Finely ground ore is conveyed by the air stream to a horizontal classifier, where expansion and a change in direction cause the +I50 mesh fraction to fall onto a vibrating

Jan 1, 1962

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By Vernon E. Swanson, Tom G. Ging

Experiments indicate that simple addition of water to mixtures of untreated trona and otherwise insoluble leonardite yields a rich, black, slightly alkaline solution of concentrated humic substances. Prices of both trona from Wyoming and leonardite from South Dakota and Wyoming are very similar-$10-30 per ton. Leonardite is the term commonly given to naturally weathered, oxidized coal that is readily soluble in slightly alkaline water.1 Several tens of thousands of

Jan 1, 1973

By R. Woods

INTRODUCTION Gaudin (1), considered that "the mechanism of mineral collection is the central problem of flotation theory". From their work on adsorption phenomena in flotation for more than fifty years (2), Gaudin and his co-workers have made major contributions to the elucidation of this mechanism, a fact acknowledged by their contemporaries in the field (e.g. (3)). Their investigations in a number of areas, e. g. demonstrating that submonolayer quantities of adsorbed collector species can induce flotation, or identifying the influence of substances which can activate or depress (1), have helped to provide the basis for and the development of a theory to account for the interaction between mineral and collector. It was established in the late fifties (4) that the presence of oxygen is a prerequisite for the flotation of metal sulfides with thiol collectors. This fact rendered inadequate the concept of simple ion adsorption being responsible for rendering these minerals hydrophobic. The requirement for oxygen has been explained (1) in terms of this species being a component in chemical reactions between the sulfide surface and the collector. Gaudin has been instrumental in identifying the products of chemical reactions at sulfide minerals (1, 5), a line of work which has been continued particularly by Finkelstein and co-workers in South Africa (6). In presenting a detailed mechanism of the mineral-collector- oxygen interaction, it has often been considered that the mineral surface [must] first be oxidized to a metal oxy-sulfur species which

Jan 1, 1976

By R. A. Spurling, C. G. Rhodes

SATISFACTORY metallographic sample preparation of very soft metals, such as lead and its alloys is generally difficult. The prime requisite of any technique must be that the result gives an undis-torted microstructure for the microscopist to examine. A small amount of mechanical polishing followed by a chemical or electrolytic polish is usually the most desirable way to obtain an undis-torted surface. Several chemical-4 and electrolytic3-' polishing solutions have been developed for dilute lead alloys. Perchloric acid mixtures (with acetic anhydride, ethyl alcohol, or water) are among the most prominent electropolishing solutions used for lead; however, the presence of bismuth in the alloy precludes the use of any perchloric-containing solution. The other solutions1-7 were found to be unsatisfactory on alloys ranging from 10 to 65 wt pct Bi in lead. With increasing bismuth content, the microstructure shows a lead (terminal solid solution), 0-6 mixture, E (peri-tectically formed hexagonal phase), and E bismuth mixture (eutectic at 56.7 wt pct Bi).9 The metallographic samples were mounted in "Araldite" epoxy (the heat generated during polymerization does not alter the microstructure), ground by hand on well-waxed silicon carbide papers (400 and 600 grit), and polished with 3- and 0.25-CL diamond paste on billiard and microcloths, respectively. The use of the various polishing and etching solutions reported in the literature resulted in the formation of irremovable reaction products on the sample surface when applied to "as-ground" or "as-polished" surfaces. The E phase was the most difficult to clean chemically and in the development of an etchant for this system several solutions which satisfactorily etched the bismuth or a phase were unacceptable because of their reaction with the E. It was found that a mixture of 50 ml lactic acid 30 ml nitric acid 20 ml (30 pct) hydrogen peroxide (Solution #1) was a satisfactory etchant for the a-matrix alloys. The samples were prepared as before and etched after 1 min of polishing with 3-p diamond paste. The etchant was applied by swabbing (light pressure) for 30 sec to 1 min and the sample was then rinsed in running water. The E has a slight stain and the a is fairly bright, Fig. 1.

Jan 1, 1965

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By A. M. Gaudin, C. S. Chang

Adsorption was measured for barium ion and laurate radical, using radioactively marked agents, over wide range of concentrations. Laurate adsorbed in absence of barium fails to float. With barium, flotation-effective laurate coating needs not exceed 5 pct of monolayer. Barium adsorption then is several fold larger. No barium laurate coating is obtained. IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.'-' The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods."-" In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba" to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,' were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand-picked quartz, washed free of stains, were reduced in size to —20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This —200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.' The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74-micron quartz particles, using a surface factor of 1.96; is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1953

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments, and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union, and the United States are summarized Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1980

By Nicholas J. Grant, Joseph T. Blucher

High-purity aluminum and an Al-10 pet Zn alloy zvere tested in axial fatigue from 80" to 900oF, at struzn vales of 5 and 150 pct per min, at a strain amplitude of 1 pcl. Cycles to failure were recorded as well as the load per cycle during the entive test. Several grain sizes were examined in each material. Examination was made of modes of deformation, initiation and growlh of' cracks, and vecovery mechanisms such as srbgrain formation and boundary migration. Strain rate effects on cycles to failure are first observed ahoi'e 50O0F, the highev vate vesulting in longer lije. Crack initiclion at room temperature may be truns-or iutercrystalline but fructures are transcrystalline. Abore 600'F, crack iniliation and growth ave largely inlercvystalline. Boundary wzigratiotz to 45-deg positions is observed above 70Oo F, and fractrrves are a combination of grain bol~ndary voids and cvacks. It is only in recent years that studies of deformation and fracture which prevail in fatigue at elevated temperatures have attracted significant attention.' Of such studies considerably less attention was given to high strain-low strain rate fatigue. Moreover, the majority of high-temperature fatigue studies were performed at conventional machine speeds (1000 to 10,000 cpm). As it is well-demonstrated in uniaxial creep-rupture series, at high strain rates, even at high temperatures, metals undergo work hardening with little or no attendant recovery or recrystallization thus the nature of deformation and fracture which is observed is similar to that encountered at lower temperatures.'-" Thus, for example, fatigue testing of a stainless steel at 750°F does not involve high-temperature deformation processes,2 and might more correctly be termed "fatigue testing at an elevated temperature". It was the purpose of this work to study deformation and fracture in fatigue as a function of low strain rates and temperature, selecting conditions which would result in grain boundary sliding, migration, fold and subgrain formation, and intercrystalline cracking in high-purity aluminum and a high-purity A1- 10 pct Zn alloy. Grain size was an additional variable. Extensive studies of the deformation and fracture behavior of these aluminum materials in simple creep had been done in the authors' laboratory, and were to serve as a basis of comparison for the observed effects in fatigue:'-'' the range of the creep test temperatures was 80° to 1150oF. MATERIALS AND EXPERIMENTAL PROCEDURE The compositions of the 99.99 pct pure A1 and the A1-10 pct Zn alloy are shown in Table I. Button-head specimens, with a liberal fillet, of 0.20 in. diam and of gage length 0.40 in. were machined from wrought bar stock. The ratio of 2:l gage length to diameter was selected after preliminary tests showed that a shorter length gave a shorter life, probably due to end effects, and after evidence of buckling in longer gage length specimens. After machining, the specimens were chemically polished to remove the worked outer layer, and were subsequently heat-treated to stabilize the selected grain sizes. Both the high-purity aluminum and the A1-10 pct Zn alloy were heat-treated to produce grain diameters of approximately 0.5 and 2 mm in each case. These grain sizes are referred to in the text as fine and coarse grain, respectively. One lot of the high-purity aluminum was heat-treated to produce a still coarser grain size in which the cross section was occupied by 2 to 3 grains. This structure is referred to as very coarsegrained. After heat treatment, the specimens were again electropolished. To avoid complications of both stress and strain gradients in the cross section of the specimen, a hydraulic, axial fatigue machine was designed and built. A button-head specimen, 1/2 in. diam at the head, was firmly gripped in a split-type holder free of any play in the grips. The test temperatures varied from 80" to 900°F. The strain amplitude in all of the reported tests was 1 pct for a total strain amplitude of 2 pct. The strain range was set by precision micrometers and measured by a precision dial gage. Constant strain rates of 5 and 150 pct per min were selected so that high-temperature type deformation and fracture would occur in the higher-temperature tests5,6 The strains and strain rates must be regarded as nominal values because they are based on the original specimen dimensions, which changed significantly as a result of necking and crack propagation, as can be observed from Fig. 8. For the elevated-temperature tests, a thermocouple was inserted into a well in the head of the specimen; the selected temperatures could be maintained with less than ± 5oF fluctuation during the entire test. To avoid changes in grain size before the test, specimens were heated to the test temperature in less than 15 min; similarly, they were cooled to room temperature after fracture with an air blast to avoid or minimize recovery or recrystallization. During the fatigue tests, load vs strain curves were recorded by a strain gage load cell for each fatigue cycle. In addition, the maximum values of load amplitude were recorded for the entire test.

Jan 1, 1968

By Harry E. LeGrand

Most mine operations are hampered to varying degrees by excessive inflow of water into mines or scarcity of water for processing the materials. These internal problems are compounded in many cases by such external hydrological problems as lowering of ground-water levels in areas outside the mine properties, subsidence of ground surface, adverse geochemical changes, and pollution. The development of a mine below the water table disturbs the natural ground-water system, causing a convergence in the flow of water from a surrounding area. The mine becomes the apex of a depressed cone in the water table. The fact that mines are commonly located in complex and somewhat anomalous geologic environments prevents an idealized treatment of the mine as a well that would be similar to a water well in a homogeneous aquifer having isotropic conditions. Yet, adherence to some principles of ground-water behavior is helpful when combined with an understanding of the local geology. A program calling for an appraisal of all pertinent hydrological conditions prior to mining and during various stages of development should supply adequate information for mine officials to anticipate difficulties and to allow for corrective measures. Before and during mining operations there should be a mine hydrology framework and plan, in which there is continual upgrading of such considerations as anticipated actions, consequences of actions, remedial plans, and contingencies.

Jan 1, 1973

By S. G. Epstein

Electromigration has been measured in dilute liquid alloys of lead in antimony and antimony in lead. In these alloys antimony migrates with the electron current; lead migrates in the opposite direction. These results, which contradict the mass criterion, were predicted by the electron drag model for electromigration in liquid alloys. The existing experimental data are shown to correlate with the difference in electrical resistivities of the alloy components. FOR many years investigators have attempted to relate observed electromigration phenomena in liquid alloys to the physical properties of the alloy components. The most successful correlation was found by Angus et' al.,1 who in 1959 proposed an empirical criterion for predicting the relative direction of motion of the components of a liquid alloy in an electric field: the component with the smallest atomic mass concentrates at the cathode. While this criterion is obeyed in nearly all the alloy systems which had been investigated, the physical basis for such an effect was not understood. It was also disturbing that the mass criterion predicted the wrong sign for the Haeffner effect; observations with pure liquid metals revealed that in every instance the lighter isotope was transported to the anode.2 Klemm3 explained these isotopic separations by suggesting that the lighter isotopes were more mobile and more easily carried to the anode with the electron stream. Additionally, several deviations from the mass criterion have been found in liquid alloys, notably involving transition metals such as chromium, nickel, palladium, and zirconium, which migrate to the anode in liquid bismuth.4'5 Recently, a model has been proposed6 in which electromigration in liquid alloys is attributed primarily to the interaction between the electron stream and the metal ions. In essence, this model predicts that the component with the greater electron-ion scattering cross section will be preferentially transported to the anode, displacing the other component to the cathode. The electrical resistivity of each pure component at its melting point is taken as the measure of its scattering cross section. This model was developed from the results of systematic studies with various solutes in liquid mercury,7'8 bismuth,9 and sodium.10 In every alloy, the component with the greater resistivity has centrates at the anode. Coincidentally, in every instance the component with the greater resistivity has also the greater mass, apparently satisfying the mass criterion. In order to differentiate between electron-ion coupling and atomic mass as the relevant physical prop- erty influencing electromigration, measurements were made with Pb-Sb alloys. Lead has an atomic mass nearly twice that of antimony, but lead has an electrical resistivity of 91 microhm-cm while antimony has a value of 113.5 microhm-cm at their respective melting points. The mass criterion predicts that in an alloy of the two antimony will concentrate at the cathode; the electron drag model predicts that antimony will concentrate at the anode. EXPERIMENTAL To conclusively determine the relative motion of lead and antimony in each other, solute electromigration was measured in dilute liquid alloys of antimony in lead and lead in antimony. Both starting materials were 99.999+ pct pure. The measurements were made with the same capillary-reservoir technique previously used for measuring electromigration in liquid bismuth alloys.11 Several changes in the experimental apparatus were necessary, however, to accommodate liquid antimony, which has a higher melting point than bismuth. The modified apparatus is depicted in Fig. 1. In each experiment four quartz capillaries were filled with the molten alloy. A direct current was passed through two of the capillaries; the electrode in one of these capillaries was made the cathode, and the electrode in the other was made the anode. The remaining two capillaries sampled the alloy in the reser-

Jan 1, 1969

By Alfred Boyles

"Heredity"1 in cast iron has been a subject of much discussion. Numerous experimenters have found that the properties of gray iron may vary greatly without corresponding variations in composition or thermal treatment. The main structural difference in such cases is in the size and distribution of the graphite flakes and the explanations given usually attribute this difference to some chemical element not shown by ordinary analysis or to some physical factor, such as inclusions in the melt. It cannot be said that any of these theories is completely satisfactory. Much remains to be learned about cast iron and for this reason a study of the material was undertaken as a part of the program of fundamental research at Battelle Memorial Institute. A review of the literature indicated that very little systematic work had been done on the mechanism of freezing in cast iron. The experiments described below are largely concerned with that problem. Normal and "Dendritic" Cast Iron As examples of variation in type of structure, photomicrographs of two test bars of cast iron are shown (Figs. 1 and 2) and the composition and properties are given in Table 1. Both are common, unalloyed gray iron. Test bar No. 13 has normal graphite flakes while No. 49 has very fine, lacy graphite arranged in a dendritic pattern, the matrix in both being pearlite. These two types of cast iron are well known to foundry-men and need no detailed description.

Jan 1, 1937

The earliest U. S. patent on a crushing machine was issued in 1830. The device incorporated the drop hammer principle later used in the famous stamp mill, whose history is so intimately linked with that of the golden age of American Mining. Eli Blake invented the first successful mechanical rock-breaker --the Blake jaw crusher--patented in 1858. The idea of his mechanical principle, the powerful-toggle linkage, was so sound that today the Blake -type jaw crusher is the standard by which all jaw crushers are judged. In 1881, Philetus Gates was granted a patent on a machine which included in its design all the essential features of the modern gyra tory crusher. For some years after these pioneer machines were developed, crushing requirements were quite simple. All underground mining and open-pit quarrying was done by hand with tonnages and rock sizes generally small. In the milling of precious metal ores, stamp mills were popular as the final reduction machine. The stamps were fed with an ore size readily produced by one break through small gyratory or jaw crushers. Even in large underground mining operations, there was no demand for large crushers; and increasing tonnage requirements were met by duplicating the small units. The Homestake gold mine in South Dakota was a good example, where in 19 15 twenty -two small Gates gyratory crushers were used to prepare the ore for the batteries of 2,500 stamps. Open pit mines and the introduction of the steam shovel created a demand for larger crushers, which led to the development of a gyratory with an 18 in. (457 mm) receiving opening. Up to this time, the jaw crusher had kept pace with the gyratory, both from the standpoint of receiving opening and capacity; but now the gyratory stepped into a 15-year lead with larger and larger sizes. This trend toward large primary crushers started just before the turn of the century, and in 1910 crushers with 48 in. (1.22 m) receiving openings were being built. About this time, the jaw crusher was revived in a great contribution to primary crushing by the introduction of the 84 in. by 60 in. (2. 13 by 1. 52 m) machine. This crusher was usually followed by a 24 in. (6 10 mm) opening gyratory crusher for secondary breakage, a system which reawakened the industry to the use of the jaw crusher as a primary breaker. It is interesting that although his machines never came into general use, Thomas A. Edison ranks as a pioneer in the development of the large primary breaker. Edis on reasoned that the recoverable electrical energy

Jan 1, 1978

The Institute is still in need of additional copies of the Bulletin for January, February and March, and will be glad to pay members the regular price of fifty cents per copy. Copies may be sent express collect, or postage may be used and the amount will be refunded in addition to the fifty cents.

Jan 10, 1916

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1943

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1942

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1939

SEC. 1. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its abbreviated title A. I. M. E. SEC. 2. The objects of this Institute, as set forth in its certificate of incorporation, are: "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information the obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of address, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy."

Jan 1, 1936

By Telfer Norman

THE use of cadmium as a base for bearing metals is one of the most interesting recent developments in this field. It has caused a strong demand for cadmium and a marked rise in its price. It appeared to the authors, therefore, that the situation might be relieved for users if accept-able substitutes could be developed. A preliminary investigation has revealed that to some extent mercury may be substituted for cadmium. Whether its use is justified cannot be stated at this time. Most of the authors' work has indicated that the addition of mercury to alloys of cadmium and nickel detracts from their desirable physical properties; but this work has not been extended to cover service tests, which might reveal that the addition of low percent-ages of mercury to the cadmium-base alloys would improve their per-formance. The results of tests made by the authors are therefore briefly summarized for this paper. Table 1 gives the proportions of the metals

Jan 1, 1937

By B. Ramaswami

INTERNAL oxidation occurs readily in silver due to the rapid diffusion of oxygen in silver.' It has a marked effect on creep in polycrystalline silver2 and raises the critical resolved shear stress in single crystals of silver.3 However, the effect of oxygen on the work-hardening parameters of silver is not known. It is the aim of this paper to describe the effect of internal oxidation on the work-hardening characteristics of single crystals of silver and an Ag-0.1 at. pct A1 alloy. The materials used were: 99.99 pct Ag from Handy and Harman and 99.993+ pct A1 from Alcoa. Single crystals, 6 mm by 6 mm in cross section of silver and Ag-0.1 at. pct A1 of mo.5 orientation, i.e., the orientation with the Schmidt factor m = 0.5. were grown by the Chalmers technique.4 One set of specimens, referred to herein as oxidized specimens, was annealed at 940°C for 24 hr in a muffle furnace, in air, and furnace-cooled to room temperature. Another set of specimens, referred to as nonoxidized specimens, was annealed in oxygen-free helium at 940°C for 24 hr and furnace-cooled over a period of 7 hr to room temperature. The annealed single crystals were tested at room temperature in a floor-model Instron testing machine. The results are presented in Figs. 1 and 2. A

Jan 1, 1965