Search Documents

By A. F. Banks

INTRODUCTION Selective flocculation-flotation as a method of desliming potash flotation feed has been practiced in the Cominco Ltd. potash plant since November. 1974 when it was installed to replace a less efficient mechanical desliming process. The plant was designed for a consistent feed containing 4.5% insolubles. In practice the quantity and quality of the insoluble material is quite variable. This variability led to serious problems in the deslime circuit and consequently had an adverse effect on sylvite flotation performance. A costly mechanical solution to the problem was being seriously considered when it was drawn to our attention that a selective flocculation-flotation process had been developed. The process was tried first in the laboratory on the Cominco Ltd. ore, then on a pilot basis on 25% of the mill feed and finally full scale. The time from being informed of the process to full scale operation was 18 months. It has since been incorporated into a tailings regrind circuit. The original mine design called for the mining of an 11 foot height up to the top of the three clay seams. These had to be taken as they were a zone of structural weakness. It also assumed that the beds would be uniform with only a few disturbances. Very soon after the initial start up it was found that permanent openings had to take in the layers right up to the upper clay seams and because of the mining process that this material would have to be milled when encountered. The number of disturbed areas in the mine is greater than the design anticipated. In operation the insoluble content of the mill feed varies from 4.5% to 8% plus with the peaks being very short- term to relatively long, from hours to day. In terms of quality, the insolubles in the mining horizon are relatively soft and easily liberated, whereas those above are hard and liberate slowly.

Jan 1, 1979

From the early part of the thirteenth century bituminous coal was called "sea coal" in England, from the fact that the coal seams in the Fife and Northumberland fields outcropped on the shores of the North Sea and wave action and erosion resulted in lumps of coal being found in large quantities along the shores. These were gathered by women and children and sold for fuel to replace wood. Coal first reached London by sea, and there was a "Secole Lane" in that city in 1228. The term was gradually applied to all coal and for some hundreds of years all coal in England was called "sea coal", and the term is not yet obsolete there. Another reason for the use of a defining word was the fact that from time immemorial, in England and elsewhere, the word coal meant char-coal, or coal made from wood, as this was the common fuel of those times when anything other than natural wood was burned. The biblical references to coal all mean wood-coals or charcoal, and one must be careful in writings prior to at least 1750, when "coal" is used to be sure that it means stone, or mineral coal, rather than wood or charcoal. "Sea-coal" was in common use along the Atlantic seaboard until after about 1780; the first map showing coal in Pennsylvania, Ohip and Kentucky, made as of 1750, used the term "sea-coal here."2 In the interior stone coal was used by the early writers almost entirely, partly to differentiate it from charcoal, but largely because it was found with stones and rocks, and in most places then had the same value. "Fossil" coal was used by Hamilton in 1790. Jefferson called it mineral coal and pit coal in 1781. The term mineral coal was usually used in the governmental references to it as late as 1850, but the present use of bituminous coal began as soon as anthracite came on the market in 1820. Both mineral and stone coal still survive in the laws of several states specifying the weight of a bushel of coal.

Jan 1, 1942

By F. Lynwood Garrison

The enormous growth of the manufacture of Bessemer steel in this country within the last few years, due to the almost constant large demand for steel rails, renders it very desirable that our knowledge of the physical and chemical properties of a material upon which we place so much dependence should be increaqed by every possible means. It was with this end in view, and also in hopes of learning something of the causes affecting the regularity of the Bessemer product, that I took up the subject of this paper a short time ago. The lise of the microscope as an instrument of research in the metallurgy of iron and steel is now fairly well established;

Jan 1, 1887

At the MBD Business Meeting held on March 1, 1971, the General Committee of the MBD Division voted unanimously to change the name and expand the role of the Fluo-Solids Separation Committee. The new committee is called the Environmental Control Committee. Such action was taken because of the importance of environmental control and the need for a more active role in this area by our Division.

Jan 1, 1971

By D. A. Stevenson, R. A. Burmeister

Single-phase silver antimony telluride has been prepared by zone-melting techniques using initial compositions of A new phase appears upon prolonged annealing of this material, but the reaction does not appear to be a simple eutectoid decomposition. A complete analysis of the phase equilibria is complicated by the slow kinetics involved. The Hall coefficient, magneto -resistance, electrical resistivity, and Seebeck coefficient are all sensitive to the presence of second phases. The low Hall mobilities measured for single-phase material indicate that the usual band theory is inadequate to explain the observed transport properties in the system. Density anomalies of up to 2.5 pet between measured and theoretical density were observed but are not conclusive evidence for a defect structure. COMPOSITIONS in the Ag-Sb-Te system have been studied previously by several investigators.1"18 The interest in this system arises from potential thermoelectric applications of alloys on the Ag2Te-Sb2Tes vertical section. Although the composition corresponding to the formula AgSbTe, has received most attention, it has been found to consist of more than one phase.7'8 A thorough understanding of the properties of this heterogeneous material has been impeded by both lack of knowledge of the properties of the homogeneous phases comprising it and the problem of analysis of transport properties in an inhomogeneous system. The present work describes the preparation of the homogeneous ternary phase and the corresponding electrical properties of both homogeneous and heterogeneous material. MATERIAL PREPARATION Most specimens for this investigation were prepared by encapsulating the elements in evacuated quartz tubes after which they were melted and homogenized in the liquid state. The ambient temperature was then dropped to 500°C and the resulting ingot zone melted. The growth rate, width of zone, stoichiometry, and number of passes have an effect on the resultant microstructure. Grains several centimeters in length were easily produced by this method. Other solidification techniques were also used, including uniform slow cooling of the entire specimen and rapid freezing. The microstructures of specimens produced by these techniques frequently differed appreciably from similar compositions prepared by zoning. A variety of nonequilibrium microstructures characterized by long needlelike particles resulted from the rapid-freeze method. PHASE EQUILIBRIA The lack of information on phase equilibria is a major difficulty associated with a comprehensive study of the Ag-Sb-Te system. Considerable confusion has resulted from the use of the formula AgSbTe, to identify the cubic ternary intermediate phase even though it has been established that material of this stoichiometry normally contains AgzTe as a second phase.798 In this paper, silver antimony telluride will denote the cubic ternary intermediate phase comprising the major portion of AgSbTe,. The term "single phase" will denote material which consists of only the cubic phase (as evidenced by metallographic examination and X-ray diffraction) and the term heterogeneous will describe multiphase material containing AgzTe, SbzTe3, or other phases in addition to the cubic phase. The single-phase material may actually contain a variety of inhomogeneities—gradual changes in composition on a macroscopic scale, localized fluctuations in composition, clusters or other products of early stages of the precipitation process, and a variety of point and line defects—all of which will not be detected by the present techniques for determining homogeneity. Single-phase material has been prepared from compositions close to 59 mole pct SbzTe3 21 (this notation refers to the location on the Ag,Te-Sb2TeS vertical section). Zone widths of =2 cm and growth rates 51.2 cm per hr were used. The single-phase region at elevated temperatures extends off the vertical section to a composition which can be expressed approximately as Ag,,SbzgTes,.9 The latter two compositions as well as AgSbTe, are represented in the conventional Gibbs triangle in Fig. 1. It is not presently possible to ascribe exact values to the limits of the single-phase region on a given isotherm or vertical section due to the extremely

Jan 1, 1964

By W. R. Shimer

IN his valuable report on Finishing Temperatures and Properties of Rails, I Dr. G. K. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying put the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. . Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development ,of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high per centages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility, than. rails of identically the same composition and section which were rolled, direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 3, 1915

By W. R. Shimer

In his valuable report on Finishing Temperatures and Properties of Rails,l Dr. G. X. Burgess, Chief of the Division of Metallurgy, U. S. Bureau of Standards, has begun a line of investigation which should be continued by those interested in the subject, and who have proper facilities for carrying out the work. For the past year or more the Bethlehem Steel Co. has been conducting experiments to learn the effect of rail finishing temperatures on their physical properties and microstructure and the results are here given for the consideration of those interested in the rail situation. Considerable differences of opinion have been expressed by various authorities, in the past, as to the effect of large or small grain size and high or low finishing temperatures of steel rails on their physical properties and wearing qualities. Low finishing temperatures and, therefore, low shrinkage, have been advocated on the theory that the wearing qualities would be improved. Others have recommended high finishing temperatures. The generally accepted cause for rail failures, due to the development of transverse fissures, is excessive wheel pressure on hard rails. One of the causes advanced for hard rails has been that they contain too high percentages of carbon and manganese; another that the rails were finished at too low a temperature, i.e., at or near the critical point. In the experiments herein described the rails were rolled from reheated blooms. All the rail blooms were charged hot in a reheating furnace and brought up to about the original ingot-rolling temperature before rolling into rails. These rails gave better results in deflection, withstood a greater number of drops before breaking, and showed greater ductility than rails of identically the same composition and section which were rolled direct from the ingot. Rails rolled from reheated blooms, finished at somewhat higher temperatures than when rolled direct from the ingot, have a different microstructure, which the writer does not believe is due so much to the difference in finishing temperatures, as to the difference in

Jan 1, 1915

By Freeman Bishop

Of all President Nixon's many legislative proposals, the one that will probably have the most far reaching effect on the mining industry will be the collecting of odds and ends of antipollution programs into the confines of a single independent Federal agency, the Environmental Protection Administration. In addition, the President is asking this Congress to approve shifting some policy and planning to the Commerce Department in an agency that will probably be known as the Oceanographic and Atmospheric Administration. This division will deal with ocean mining policy and future sources of minerals and metals.

Jan 1, 1970

By Wayne D. Gould, Robert S. Shoemaker

Modern mill design is a combination of many factors which permit the efficient production of a mineral concentrate from operating, maintenance, and capital requirements. In general, mills should be designed to use the largest possible equipment compatible with the requirements of the ore and the owner's operating philosophy. The paper discusses the major parts of concentrating mills, from primary crushing through comminution, both conventional and autogenous, and the production of a final concentrate. Features of various plants are compared and discussed in the light of operating practice and maintenance requirements.

Jan 1, 1978

By authority of the Secretary of War, and in response to frequent requests, the following suggested list of reading is issued by the War Department for the information of civilian engineers desiring to inform themselves on military subjects: These references have been selected, first, with a view to giving to engineers unfamiliar with the art of war a general survey of that sub-

Jan 1, 1916

By A. H. Roberson, L. H. Banning

DURING the past few years, a considerable tonnage of ilmenite has been produced as a byproduct of a monazite dredging operation and stockpiled near Boise, Idaho. This ilmenite has not been marketed because of the long distance from ilmenite-consuming areas and its comparatively low TiO2 content. Production of monazite from the alluvial sand deposits of Idaho is a mar- ginal venture when it is the only marketable product, and it will be necessary to establish a byproduct market before the operation becomes economically stable. Early in 1954, the Bureau of Mines Northwest Electrodevelopment Laboratory at Albany, Ore., conducted a series of tests which demonstrated that arc furnace smelting could be utilized to produce commercial quality pig iron and a high titanium content slag from these ilmenites. Additional studies showed that the slag chlorinated readily to produce a satisfactory yield of TiCl4. The investigation was carried out by two research teams. The Ferrous Metals Branch, with adequate

Jan 1, 1956

By Scott, Turner

IN 1933, the monetary metals were produced in a ratio of 6.7 oz. of silver to 1 oz. of gold, the lowest relatively for silver since the period from 1851 to 1865. At the beginning of that period, the virgin placers of California -and Australia began producing almost simultaneously; in consequence, there was an abrupt fall in the high silver side of the ratio that had prevailed through the centuries after America was discovered. The output from the Comstock and other silver-bearing lodes, located a decade after this influx of new gold began, soon restored the production ratio to its former proportion, that is, a relatively large weight of silver compared to gold.

Jan 1, 1934

By J. W. Leonard, J. C. Anderson, C. T. Holland

PREPARATION CONTROL IN UNDERGROUND MINING Selective Mining According to district Depending upon the particular geographic loca- tion or seam characteristics, modern raw coal preparation practices can be used to obtain improved product quality and uniformity. Nevertheless, certain coal markets may require only marginal quality while others may require very high quality, and these objectives may be sought by commencing the preparation of coal underground at the "working face." Under- ground preparation involves choosing those portions of the seam which can be cleaned to satisfy predetermined market requirements involving ( 1 ) maintenance of uniformity in chemical quality, (2) elimination of removable impurities, (3) control of sizes and size ratios, and (4) control of moisture. The methods employed to attain these objectives vary widely with the (1 ) seam under development, (2) mining equipment available, and (3) changing trends in the consuming markets. When a mining property is opened and development progresses from one section to another, the (1) petrography of the coal in the seam does not remain uniform, (2) character of roof and floor are subject to change, and (3) character and prevalence of mineral impurities are subject to considerable variation. The quality of coal shipped to market from any mine depends upon intelligent foresight, planning, execution, and supervision. Mining becomes a highly technical art. The quality of coal as determined by chemical and petrographic analysis is without question one of the most important considerations in the development and life of any coal-mining property. Variations in such proper- ties as volatile matter, ash, sulfur, Btu content, and petrography are of considerable interest, and to a limited extent so are such properties as phosphorous content, free swelling index, plasticity, hardness, pressure formation during coking, and ash composition. The maximum and minimum specifications of these characteristics as established by competitive market conditions place definite limits on the marketability of a coal.

Jan 1, 1979

By A. Hasbi Hassan

Stibiotantalite is a relatively rare mineral not commonly found in the major tin districts of the world, and its separation characteristics have not been documented adequately in the literature. The investigation described here has been carried out on a sample taken from a commercial tin concentrate containing a significant amount of stibiotantalite which would have to be substantially removed before the tin concentrate was smelted. The sample originated from Greenbushes, Western Australia. A mineralogical analysis was performed on the sample with the aid of the Frantz Isodynamic separator 1 and the results presented in Table 1. A screen analysis was also performed, and the results presented in Table 2. The minerals were found to be substantially liberated.

Jan 8, 1979

By J. R. Kyte, V. O. Naumann, C. C. Mattax

Imbibition and waterflooding tests at reservoir conditions show that conventional tests at room conditions sometimes lead to recovery estimates that are too low. Core samples which are of intermediate wettability at normal test conditions may be strongly water-wet at reservoir conditions. This was found to be true for samples from two of three reservoirs investigated. For the other reservoir, less difference was observed between the wettability of samples at normal test conditions and at reservoir conditions. Samples which became more water-wet at reservoir temperature and pressure also water flooded more efficiently at reservoir conditions. These results show that core analysis tests on intermediate wettability samples should be performed at reservoir conditions to obtain representative data. INTRODUCTION Throughout the oil industry, core analysis tests normally are performed using refined oils and at room temperature and pressure. This procedure has always been subject to question because the possibility is generally recognized that the reservoir environment may influence displacement behavior. Burkhardt, et al,' have performed waterflood tests at reservoir conditions on East Texas cores. They found little difference between results obtained at reservoir conditions and results of conventional flooding tests at room conditions. As they pointed out, however, this situation might not be general since they obtained data on only one rock and crude-oil system. This paper presents data which demonstrate that it is sometimes necessary to perform core analysis tests in a simulated reservoir environment to properly represent the reservoir wettability and displacement characteristics. The work is specifically concerned with reservoirs which were thought to be of intermediate wettability on the basis of conventional test results at room conditions, i.e., core samples imbibed only small amounts of either oil or water and exhibited no decided preferential wettability characteristics. Tests were performed on cores from three such reservoirs to determine their behavior in the reservoir environment. lmbibition and waterflood tests were used to demonstrate the effect of reservoir environment on reservoir rock wettability and displacement characteristics. Results of tests performed at reservoir conditions were compared with results from conventional tests. Imbibition tests were performed on samples from all three reservoirs. Waterflood tests were performed on samples from only one reservoir. Fluid properties for the three reservoirs studied are shown in Table 1. Tests at reservoir conditions were performed using bottom-hole crude oil at reservoir temperature and pressure. The aqueous phase used in these tests was a synthetic brine approximating the reservoir brine composition. Conventional tests were performed at room conditions with refined oils and synthetic reservoir brine. The oil-to-water viscosity ratios were adjusted to the reservoir values. The cores used in all the tests were taken from the reservoirs using either brine alone or a bentonite-car-boxymethylcellulose mud without additives as coring fluids. Previous tests show that these fluids have no significant effect on the wettability of reservoir rock samples.1 The cores were preserved in brine at the wellsite to prevent wettability changes during shipment and storage. Wellsite imbibition tests have been performed on fresh samples from several reservoirs (including Reservoir A) and compared with later laboratory imbibition tests on samples preserved in brine. The comparison showed that the wettability of the preserved cores was the same as that of fresh, surfaced cores at the wellsite.2 IMBIBITION TESTS Conventional imbibition tests were performed on preserved cores using the apparatus and procedures described by Bobek, et al.2 A sketch of the apparatus for imbibition tests at reservoir conditions is shown in Fig. 1. The preserved samples were first centrifuged to expel excess water and then placed in a stainless-steel container which served

By A. L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron-

Jan 1, 1873

By Alexander L. Holley

IN order to put sufficient work on steel ingots for rails, they must be reduced from about 12 inches square. As this cannot be done at one heat, they are first drawn down to about 7 inches square, and then reheated and rolled into rails. This first reduction or " blooming," is usually done in this country in a 30-inch 3-high rolling-mill, with movable rolls, so as to get several reductions in each set of grooves. The first of these mills has been running at the Troy Steel-works above a year, with great success. Another at the Cambria Iron

By E. J. Haug, M. M. Fine

For several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published. Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 4, 1955

By E. J. Haug, M. M. Fine

FOR several years work has been carried on by the U.S. Bureau of Mines at Rolla, Mo., to develop improved methods of concentrating the oxidized ores of lead and zinc. Various samples have been investigated, and results on some have been published 1,2 lished.l, 2 Details of the progress to date are given in a mineral dressing study now being conducted for an extensive oxidized lead-bearing tract in southeast Missouri, property of St. Joseph Lead Co. These oxidized ores present problems typical of many encountered in modern mineral dressing research in that recovery of very fine particles is of

Jan 1, 1956

By C. A. Bruch, W. E. McHugh, R. W. Hockenbury

Commercially pure molybdenum specimens were irradiated in the Materials Testing Reactor for an estimated exposure of 1.9 to 5.9x10 20 thermal nvt. Prior to irradiation, the material was ductile in the tension test; whereas after irradiation, it was brittle. The results of tension tests conducted at various temperatures revealed that the transition temperature for this material had been increased from —30' to +70°C as a result of the radiation exposure. From metallographic studies, it is concluded that the embrittlement is due to submicroscopic changes which raise the flow stress-temperature curve of the material. PRIOR to ten years ago, the bombardment of metals with high speed heavy particles such as protons, deuterons, a particles, and neutrons was primarily of academic interest. These particles existed in extremely small numbers in a few laboratories and only under very special conditions. With the introduction of the nuclear power reactors, these particles are now available in enormous quantities and it has become important from a practical standpoint to learn how well metals withstand severe reactor radiations. The principal radiations of concern in reactors are neutrons and y rays, since the heavier charged particles exist only in limited regions of reactors. Seitz,' in a theoretical approach, has shown that all of these high energy particles, except y rays, have enough energy to knock atoms from lattice sites and that these knocked-on atoms have enough energy to cause additional displacements of neighboring atoms. The result of this process would be a lattice containing many imperfections in the form of interstitial atoms and vacancies. Hence, it would be expected that the properties of metals can be changed by reactor radiations, and such has been found to be the case. Only a limited amount of data have been published in the open literature,2,3 and these data have been for relatively low integrated-neutron-flux exposures. In general, one effect of reactor radiations on the mechanical properties of metals has been to increase strength and decrease ductility. It is now possible to irradiate specimens in the Materials Testing reactor at much higher fluxes and to higher integrated exposures than previously possible.' The data which are being presented here describe the effects of a relatively high exposure on some mechanical properties of molybdenum. Experimental Procedures Material: The molybdenum used in this investigation was obtained from the Climax Molybdenum Co. The two heats from which the material originated were melted under a vacuum of 5 to 30 microns and cast in 7 in. diam water-cooled copper molds. One ingot contained 0.061 pct C and the other 0.066 pct. Both ingots were hot worked by extrusion and rolling into % in. diam rods, after which they were annealed and straightened. The rods were subsequently heated to 1100°C in a hydrogen atmosphere and swaged to ½ in. diam rods at the Research Laboratory of the General Electric Co. The resulting material had an average hardness of 264 VPN, or 99.2 Rb, and had an average of 5000 grains per sq ml in the transverse section, Test Specimens: Substandard-size tensile specimens were prepared according to the specifications shown in Fig. 1. These specimens were used also for hardness measurements. The metallographic specimens were small disks which were polished, etched, and photographed at X1000 prior to irradiation. The field studied was

Jan 1, 1956