Search Documents

By G. S. Upadhyaya, A. D. McQuillan

HERE would appear to be a simple relationship between the group number in the periodic table of the early transition metals and the maximum amount of hydrogen which they can absorb.' Thus group IIIA metals (Sc, Y, and La) yield a trihydride in which the metal atoms are on a fcc lattice and the hydrogen atoms occupy both tetrahedral and octahedral interstices. Group IVA metals (Ti, Zr, Hf) form dihy-drides in which the metal atoms are on either a fct or cubic lattice, but in which only the tetrahedral interstices are occupied by hydrogen atoms. In group VA (V, Nb, Ta) the hydrogen-saturated metal attains a composition slightly below that of a monohydride under normal conditions. Finally the metals of group VIA (Cr, Mo, W) do not dissolve appreciable quantities of hydrogen. The manner in which hydrogen solubility disappears on alloying a group VA metal with one from group VIA has previously been investigated.2 It is necessary, in order to obtain a general picture of the reactions of alloys of the early transition metals with hydrogen, to examine a system containing metals from groups IVA and VA in which there must be a change from a fcc to a bee hydride phase. The system chosen for investigation was the pseudobinary system between titanium hydride and niobium hydride. Metallic alloys were prepared by melting iodide-prepared titanium with zone-refined niobium in an argon-atmosphere are-furnace. To ensure homogeneity each alloy was cold-swaged and then heated at 1250°C in a high-vacuum furnace until metallo-graphic examination confirmed its complete homogeneity. Small weighed specimens of the alloys were charged with hydrogen using gaseous hydrogen generated by heating titanium hydride. The apparatus has been described elsewhere.3 Throughout the charging process the hydrogen pressure was kept at about 1 atm while the specimen, initially at 800 °C, was slowly cooled to 150°C over a period of days. The total amount of hydrogen absorbed by each specimen and the room-temperature crystal structure of the hydride powders were determined. The X-ray investigation indicates that the fee hydride phase arises from alloys extending in composition from titanium to 67 at. pct Nb. After a two-phase field lying between 67 and 74 at. pct Nb in which the fee and bee hydrides coexist, all alloys richer in niobium yield a distorted bee hydride. Data derived from parameter measurements are presented in Fig. 1. The atomic volume per metal atom has been plotted against the composition of the initial metallic alloy in order to facilitate comparison of the effects of hydrogen addition in the two phases of different crystal structure. The amount of hydrogen absorbed by each alloy at saturation in terms of the hydrogen to metal ratio and alloy composition is given in Fig. 2. Over the whole range of the fee hydride phase the hydrogen content remains constant, while in the distorted body-centred hydride phase, the hydrogen content increases with increasing titanium content reaching a hydrogen/metal ratio of 1.4 at the boundary of the two-phase region. It seems likely, therefore, that the maximum hydrogen content of the fee hydrides is limited to a hydrogen/metal ratio of 2 because hydrogen atoms

Jan 1, 1962

By V. A. Phillips, M. Safdar Ali

The tensile properties of Cu-0.20 pct Al, Cu-0.45 pct Mg, Cu-0.27 pct Cr, and Cu-0.22 pct Be solid-solution alloys were studied at -196°, 18°, 2509 and 500°C on wires internally oxidized at 900°and 1000°C. Internal oxidation produced marked increases in yield strength relative to pure copper, particularly at low temperature. The yield strength decreased with increase in temperature to a much greater extent than predicted by current theories of dispersion hardening. The strengthening effect of internal oxidation persisted throughout the entire stress-strain curve, but since a marked loss of ductility occurred at all test temperatures, only modest increases in tensile strength were realized. INTERNAL oxidation involves the preferential oxidation of a baser solute in a relatively noble solvent by diffusion of oxygen into the solid. Since the process is diffusion controlled, it is expedient to carry it out at a high temperature often approaching the melting point. The amount of solute is limited and the oxidation conditions adjusted so that oxygen diffuses inwards to meet the solute causing reaction to progress inwards and form subscale instead of only sur face scale. The reaction can be made to occur throughout the thickness of thin material producing a fine dispersion of oxide inside the metal. C. S. Smith1"3 appears to have been the first to recognize the true nature of the process of internal oxidation. Although extensive kinetic and metal-lographic studies followed by Rhines and coworkers,4-5 Chaston7 andMeijering and Druyvesteyn8 working independently were the first to report hardening effects due to internal oxidation. These results prompted detailed studies of the effects of internal oxidation on the hardness, tensile, creep, and fatigue properties of a number of alloys by G. C. Smith and coworkers9-12 in England, on hardness by Gottardi13 in Italy, and on hardness and tensile properties by wood14 in the U.S.A. Publications dealing with other aspects of internal oxidation will not be reviewed here. Internal oxidation of solutes having a high affinity for oxygen provides a means of obtaining very fine dispersions stable in a suitable atmosphere at temperatures well above those at which most age harden ing precipitates coalesce. The process therefore offers a method of producing thin sheet and wire of possibly outstanding creep resistance. The size limitation might be overcome by internally oxidizing porous powder compacts made from alloy powder before final sintering. PREPARATION OF ALLOYS The alloy ingots, which were approximately 5 1/2 in. long by 1 in. diam, were made up in a high-frequency furnace, using as raw materials OFHC copper, 99.99 + pct Al, high-purity magnesium, and master alloys of Cu-4.19 pct Be and Cu-10 pct Cr. The alloys containing aluminum and magnesium were melted ii closed high-purity graphite crucibles and solidified in the crucible which was lowered partly Out of the coil to give a hot-top effect. The alloys containing beryllium and chromium were made by melting in vacuo in alumina-lined sillimanite crucibles. The magnesium, chromium, and beryllium

Jan 1, 1960

By S. A. Braley

THE first commercial production of bituminous coal in the United States was in 1820, and formation of acid in the areas from which the coal was removed began at that time. Thus it is 130 years since the development of mine acid began. The coal operator has had to deal with the acid water produced in his mines, and his losses from corrosion of pumps and equipment have been tremendous. Other industries and the public have been forced to spend large amounts for their water requirements because of the acid discharge from the mines. There are many contradictions in the literature on this subject probably because of variations in the analytical procedures followed and differences in the methods of calculation and reporting. The opinions previously expressed may be summarized as follows:

Jan 8, 1951

By L. C. Glenn

In the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. Oil in Tennessee A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were produccrs. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that output. Production is from a fissured part of the limestone and varies greatly in accordance with the size and extent of the ramification of the

Jan 1, 1921

By Uwe Neis, K. Peter Kiefhaber

Whereas single particle flotation is considered to be evoked by physico-chemical bubble adhesion, floc flotation seems to be governed by other mechanisms. This study demonstrates that air bubble size does not affect the flotation efficiency of inorganic particles which have been destabilized by different means: 1. addition of simple salts and 2. polyelectrolyte dosage. The air-to-solids ratio A/S does not influence the solids removal efficiency within a broad range of examination. However, there is a significant difference between A/S-values necessary to obtain optimum flotation comparing both destabilization mechanisms. Polyelectrolyte concentration corresponding to complete particle destabilization at the isoelectric point leads to optimum sedimentation rates but not to optimum flotation efficiency. To obtain optimum solids removal by flotation higher polyelectrolyte concentrations are necessary resulting in a positive solids surface charge. These effects are explained on the basis of different floc structures.

Jan 1, 1980

By J. N. Hobstetter, J. J. Becker

Slip lines in deformed copper single crystals exhibit very pronounced cross-slip and clustering if the stress axes are not too far from <100>. This orientation dependence seems to persist whether or not attempts are made to reduce the bending constraints of ordinary mechanical tests. THE purpose of this paper is to report some microscopic features of the plastic deformation of copper single crystals. The material used was OFHC copper obtained from the American Brass Co. Single crystals about 3 in. long and 5/16 in. in diameter were made by lowering graphite crucibles containing this copper out of the hot zone of a vertical tubular furnace at a rate of 1 1/4 in. per hr. The furnace atmosphere was nitrogen. The orientations of the crystals were determined by the back-reflection Laue technique.&apos; The X-ray spots usually indicated a slight lineage structure of not more than a degree or two. The crystallography of slip is discussed in Schmid and Boas.&apos; The terms classical slip, cross-slip, and conjugate slip are used here with the same meanings as in ref. 3. Compression Specimen 17 (Fig. 1) was selected because the resolved shearing stresses on eight slip systems dif- fered at most by a factor of 1.2. It was hoped that in this situation such effects as cross-slip might be made more prominent. Two intersecting planes parallel to the stress axis were ground on the crystal, using optical abrasive on a lead lap. The large plane was approximately perpendicular to the plane of the axis and the primary slip direction. Its exact orientation was determined by X-ray. The smaller made an angle of 49" with the larger, measured by reflecting a small light source. The specimen was etched with nitric acid until its diameter had been reduced 0.010 in., and then was given a metallographic polish and very

Jan 1, 1954

Unlike the bituminous part of the coal industry, the production of anthracite has been fairly well publicized; in fact until about 1845 whenever the coal industry of Pennsylvania was mentioned in papers, magazines or books, anthracite only was meant. Beginning with shipments by river in 1820 fairly complete records of shipments were published each year, and as this variety of coal was the only one used for domestic purposes east of the mountains and north of the Potomac, there was considerable interest in the producing fields on the part of the public. Transportation of anthracite was the cause of the building of the early canals in the state, and later, of some of the earliest railroads. In most publications it has been assumed that commencement of shipments in 1820 was the beginning of the industry; this is far from being so, and it is with the earlier developments this chapter will deal, leaving the later and better known records to existing publications. (See Table No. 53.) The first reference to coal in Pennsylvania by Gabriel Thomas in 1698 has already been mentioned,1 it could only have been anthracite in that section; although of course, he never saw any coal there. Little coal was used excepting by smiths for many years after that. In 1728 the Coventry Forge paid the expenses of a man "to town for Sea Coall and Steell for ye hammer;”2 in 1729 New Castle coal was sold in Philadelphia;3 in 1740 an advertisement mentioned, "very good Pitt and Sea Coal at 18 pence a bushel; at which price &apos;tis allowed to be cheaper Fewel for Hearth Fireing than Wood at the present Rates,"4 a view not shared by most of the people there for about eighty years; in 1752 Newcastle coal was again mentioned.5 There are no references to coal in the writings of any of the Moravian missionaries, although some who settled near Mauch Chunk in 1746 said that the Indians there made their pipe heads of a soft black stone, which was much more apt to have been slate than anthracite." Several stream

Jan 1, 1942

By W. L. Zeigler

THE gravity concentrator of the Hecla Mining Co. was originally constructed in 1888 by the Milwaukee Mining Co., which was operating the Gem of the Mountains mine. It was purchased by the Hecla Mining Co. in 1900, and placed in operation 2 years later. At that time FIG. 1.-HECLA MINING CO. GEM CONCENTRATOR, GEM, IDAHO. the capacity was only about 200 tons a day, but many additions and changes in equipment have been made so that the present capacity is about 800 tons. One of the outstanding improvements made was the substitution of Callow flotation cells for vanners, which occurred in 1915. The recent building of a flotation plant for treating jig tailings, and the construction of a modern surface plant at the mine, following the

Jan 1, 1927

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct Cr region were carefully resolved. Phase relationships in the 50 to 100 atomic pct region were outlined. A single intermediate phase, ZrCr,, was established in the system. A eutectic and a eutectoid were found in the zirconium-rich region of the system, while a eutectic was located in the chromium-rich region. Limited solubility of chromium in both a and a zirconium was observed. THIS is another in a series of papers on zirconium-base binary phase diagrams based on a program sponsored by the Atomic Energy Commission. The Zr-Sn,&apos; Zr-Si,&apos; and Zr-Mo and Zr-W" systems have already been published. Previous work on the Zr-Cr system includes a partial diagram by Hayes, Roberson, and Davies&apos; and a complete diagram by McQuillan." The phase relationships reported by these authors were determined with magnesium-reduced zirconium, whereas those reported herein are based on iodide metal. Some X-ray work on the intermediate phase in this system was also reported by Hayes et al., as well as by Wallbaum.&apos; Comparisons with these data are made in the appropriate sections. Thermal analysis, metallographic and incipient melting techniques were employed to accurately resolve phase relationships in the 0 to 50 atomic pct Cr region, while the remainder of the diagram is outlined on a basis of cast structures and thermal analysis. A description and analyses of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar (Westinghouse "Grade 3") was used. This material was produced by the decomposition of a volatile iodide onto a hot zirconium filament. The as-received crystal bar was coated with corrosion product from a standard autoclave test by which its grade designation is determined. A sand-blasting and subsequent HF-HNO, pickling treatment was employed to remove this contamination. The bars were cold-rolled to approximately 1/32-in. sheet, pickled again, sheared to 1/4-in. squares, washed with acetone, and stored for use. Ingot chromium metal from National Research Corp. and electrolytic chromium flakes from Johnson, Matthey and Co., Ltd., were available as alloy additions. The ingot chromium was received in granular form. The large granules were sized by crushing, treated for iron removal, rinsed with acetone, and stored. The flakes were broken to approximately 1/8 in. with mortar and pestle, cleaned with acetone, and stored for charging. Experimental Procedure A nonconsumable electrode arc furnace identical to that described by Hansen, Kessler, and McPher-son,&apos; was used in this work. A 400 amp dc welding generator was the source of power. To insure homogeneity, ingots were melted in a water-cooled spun copper crucible, a total of four times without opening the furnace. No difficulties were encountered in the preparation of these binary alloys. Analyzed chromium contents were found to agree very well with the intended content. Melts of pure zirconium were interspersed in the course of preparing the alloys and their hardness was measured to keep a constant check on the melting technique. Vycor and quartz bulbs were used to contain the samples for isothermal annealing treatments. Vycor bulbs were employed for temperatures up to 110O°C, while quartz was used above this temperature. For treatments up to 950°C the bulbs were evacuated before sealing, but for higher temperatures a partial pressure of argon was admitted to the

Jan 1, 1954

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well&apos;s results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. &apos;This means that careful measurements of surges occurring in actual field operations must be made.

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations.

Jan 8, 1979

By R. P. Rothwell

Instruction by correspondence is certainly one of the most important and useful of modern educational methods. The paper on the " Scranton International Schools," by Prof. Stoek (Buffalo meeting, October, 1898),* gives an elaborate description of a single private enterprise in this direction, ignoring all others, and cannot be said to present a fair or impartial view of

Jan 1, 1900

By James F. Watson, Jack L. Christian

The austenite to martensite solid state phase transformation in the 300 series austenitic stainless steels was studied over the temperature range of 788° to -423°F. The primary variables controlling this transformation are temperature, plastic strain, and chernical composition. Consequently, temperature effects were studied by measurements at 78", -100°, -320°, ad -423°F; plastic strain was controlled by cold-rolling the alloys varying amounts between 40 and 80 pet; and chemical compositions were varied by using 301, 302, 304 ELC, and 310 stainless steel alloys which exhibit varying degrees of austenite stability. The martensite contents of various alloys were correlated with several mechanical properties including yield and ultimate tensile strength, elongation, and notched tensile strength (Kt = 6.3). The yield and tensite strengths generally increased with increasing martensite content, but ) no correlation was observed between elongation and martensite content. The notched/un-notched ratio (Kt = 6.3) at -423°F exhibited a maximun at about 65 pct martensite. Attempts to correlate austenite stability (as measured by the Ms temperature) with both martensite content, and incremental increases in martensite content resulting from tensile testing were generally unsuccessful because the variable of cold Work could not be separated. As a result, only a general correlation of these variables was obtained. A (111) pole figure of austenite in a cold-rolled 301 stainless steel mas prepared an attempt to further investigate directionality as exhibited by mechan- ical properties. Yield strength was correlated with this pole figure, but ultimate and notched tensile strengths were not. 1 HE literature contains a wide variety of references pertaining to the austenite to martensite solid state phase transformation in austenitic stainless steel, see references 1 through 18. Discussions of the crystallography and kinetics of this transformation are given in references 2, 7, 8, &apos;and 11, while further discussions of austenite stability and hardening mechanisms are given in references 1, 3, and 10. Two important processing variables involved in this reaction are the degree of cold work and the temperature at which cold work is performed, and the nature of these effects are outlined in references 4 and 12, and 15 and 16 respectively. The latter two references deal primarily with cold rolling conducted at subzero temperatures. The effect of chemical composition on the austenite to martensite reaction was treated in detail by Eichelman and Hull, and they determined an equation for the M, temperature of this type of steel which included the effects of nickel, chromium, carbon, nitrogen, silicon, and manganese.5 Previous studies have shown that austenitic stainless steels of AISI types 301, 302, 304ELC, 310, and 301-N exhibit mechanical properties between 78" and -423"~ that are microstructure dependent, and the dependence of this microstructure on chemistry, temperature, tensile stress, and prior deformation is in general accord with previous investigations which have measured the effects of each of these variables on structure, or more specifically, the austenite-to-martensite transformation.lg The behavior of fully stable alloys, such as ATST type 310, at cryogenic temperatures is

Jan 1, 1962

By C. Schlumberger

SINCE the beginning of .the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally. the measurements are made syste-matically along the whole length of the open hole. The physical factors or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1932

By G. D. Rieck, G. H. G. Vaessen, D. L. Vogel

Both doped and undoped tungsten single crystals exhibit hardness anisotropy with respect to the direction of testing in each of the crystallographic phes investigated. The hardness anisotropy of undoped single-crystal tungsten is rather pronounced in (001) and (110) planes but very minor in (111) planes. The anisotropy in (122) planes of the doped and drawn tungsten after recrystallization is in accordance with a previously published concept of a stringlike distribution of the doping material in the metal. ANISOTROPY in mechanical properties of single-crystal tungsten was investigated by Rose et al., Garlick and Probst,2 and Beardmore and Hull. 3 Although data on the Vickers microhardness of tungsten have been published (see, e.g., Boosz 4 and the references cited by him), no data on the microhardness anisotropy are available. We report, therefore, some of our own results on the microhardness and its anisotropy. The microhardness has been determined of the following samples. A) Polycrystalline tungsten samples taken from: 1) powder metallurgical tungsten "normally" doped with potassium-silicon-aluminum oxides (final contents inppm: K, 100; Si, 100; Al, 20; Cr, 20; Fe, 50; Mo, 400; Ni, 10) and in the form of: a) a 10-mm-diam swaged ingot annealed at 1600°C, the grain sizes varying between 15 and 250 p; b) a sheet rolled at about 800°C and recrystallized at 2000°C7 the grain sizes varying between 15 and 150 p; c) a 2-mm-diam swaged rod, as-worked, with elongated grains (average diameter of about 25 , lengths up to 1 mm); 2) undoped electron-beam-melted tungsten with very large grains (contaminations in ppm: K < 10; Fe < 20; Cr < 10; Cu < 0.1; Ni not detectable; inter-stitial~ not determined). B) Single-crystal samples taken from: 1) pure tungsten grown on a Pintsch wire by the van Arkel procedure (main contaminations inppm: Mo, 100; Si < 10; Cu and Fe, 2; A1 < 2; interstitials not determined); 2) zone-melted undoped tungsten (analysis as under A2); 3) large crystals in secondary recrystallized tungsten

Jan 1, 1969

By Harold R. Wampler, John L. Bolles, Adrian J. Broderick

Phelps Dodge&apos;s 60,000 tpd Morenci Concentrator has been in operation since 1942. The integrating of process control applications into the concentrator began in 1972. A process control system is presently on-line controlling 30 primary grinding circuits and all reagent additions. The system consists of a centralized control room process control Computer, on-stream X-ray analyzer, on-stream particle size analyzers and an operator interface. This paper describes the process control system&apos;s development, control concepts and its influence on the concentrator performance.

Jan 1, 1978

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Since the beginning of the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.&apos; Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally the measurements are made systematically along the whole length of the open hole. The physical factors , or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1934

By C. R. Watts

The feasibility of producing composites containing nickel or molybdenum fibers in a beryllium matrix was inrestigated. The composties studied were jabricaled by powder mallurgical techniques. The 1-mil-diarr nickel fibers reacled completely below 900°C, converling the fibers .from nickel to Ni5Be2,. As the /LO/-pressing temperalure as raised above 1110oC, tlie nickel diffused outward from the beryllide fibers. The solid solubility of nickel in beryllium was clboul 20 wt pet at the 1100°C pressing temperature a1 the zone-fiber interface. The 1.5-mil-diam molybdenum fibers slzolred no evidence of reaction and little evidence of diffitsion after pressing at 900°C. Between 1000° and 1050°C pressing conditions, the fibers began lo react , producing 1ayers of MoBe2 and MoBe12, respectively surrounding the molybdenurn core. The struture remained the same at 1100°C with no evidenre of solid solubility of the molybdenum in the berylium or vice versa. In recent years a considerable amount of attention has been devoted to the determination of methods for improving the mechanical properties of materials through the use of fiber or whisker reinforcement. Previous work with metal matrix composites indicates that the study of the chemical compatibility of the fiber and matrix is an area requiring greater understanding. The metal-metal or ceramic-metal interface is frequently subject to chemical reactions that may result in the formation of hard brittle intermetal-lic compounds and/or low melting point eutectic compositions. The reaction products may reduce both the low-temperature and elevated-temperature strength of the composite by weakening the fiber-matrix bond, producing premature failure at the interface. It is well-known that most metal-metal systems and many metal-ceramic systems of interest for structural composites are thermodynamically unstable,&apos;-" particularly at elevated temperatures. If, however, the rate of reaction under the conditions of fabrication is sufficiently low. composites can be fabricated that can be used efficiently for indefinite periods at low temperatures and for short periods at elevated temperatures. This paper presents the results of a series of tests to determine the compatibility of nickel and molybdenum fibers with beryllium at various hot-pressing temperatures. Nickel was selected as a candidate fiber material primarily because the relatively ductile fibers might be useful as crack arresters in applications such as ballistic impact where crack growth can result in catastrophic failure. The high density and the reactivity of nickel were primary factors detracting from its selection as a possible reinforcement. Molybdenum with a modulus of elasticity of 52 Xlo6 psi is one of the few metallic materials having a modulus higher than beryllium (42 X lo6). Its high modulus, coupled with its refractory characteristics, made molybdenum an attractive candidate for a relatively stable fiber reinforcement for beryllium. Its density, being higher than that of nickel and over five times that of beryllium: detracted from its other characteristics. EXPERIMENTAL PROCEDURE The specimens were prepared from beryllium powder with a dispersed phase of fibers by powder metallurgical techniques. P-20 grade powder, Table I, from Berylco was used as the matrix material. Short lengths of 0.001-in.-nominal-diam nickel fibers supplied by the Sigmund Cohn Corp. and 0.0015-in.-nominal-diam molvbdenum fibers obtained from the General Electric Co. were used as the dispersed phase. The composite constituents were combined under an argon atmosphere by mechanically mixing the powders and fibers. The compositions used were nominally 1 vol pct fibers. After mixing. the composites were hot-pressed into a-in.-diam pellets under an argon atmosphere at 900°, 1000". 1050". and 1100°C at a pressure of 6000 psi with no hold time at these temperatures so that a comparison could be made between the resultant microstructure and hot-pressing temperature. The billet was heated at a rate on the order of 30°C per min to the desired temperature and then cooled at a somewhat slower rate. The microstructure obtained should be considered as characteristic of the integrated time-temperature history of the sample, as well as the maximum temperature attained. Upon removal from the hot-pressing dies. the specimens were cut. mounted. and polished by standard procedures. No etchant was used in specimen preparation. Photomicrographs, electron microprobe scans, and electron back-scatter pictures were made. X-ray dif-fractometer patterns were made of several of the specimens. but only the lines for beryllium could be resolved. Specimens for optical and electron microprobe examination were selected partially for the roundness of the cross section. A round cross section was taken to indicate that the body of the fiber was approximately normal to the surface and that therefore effects due to fiber material immediately below the surface could be neglected. RESULTS AND DISCUSSION The microprobe scans indicated that nickel reacted as low as 900°C, converting the entire fiber cross section to NisBe21. Fig. l(a). There was no evidence of further reaction from the optical or the back-scatter pictures, Figs. 2(n) and 3(a).

Jan 1, 1970