Search Documents

By J. J. K. Daemen, C. Fairhurst

Introduction The stress field around a supported tunnel can be considered as being composed of: i) the virgin (pre-mining) stress in the rock ii) the (elastic) change in this stress field caused by creating the opening iii) the (time-dependent ) change in the stress field produced by (i) and (ii) as a section of the rock breaks up iv) the (time-dependent) influence of the stress build-up in the support. Several authors have examined the conditions necessary to produce static equilibrium between the support, the rock, and the regional (in-situ) stress field. The analysis used by Labasse (1) is typical. Consider a circular tunnel radius R in a hydrostatic stress field (P), and a radial pressure pi exerted by the support. According to Labasse, the radius ‘b’ to which the rock will break* for a given support pressure, pi, can be calculated from: - the equilibrium equation: [ ] As a zone of broken rock develops around the opening, the stress circle for a point on the elastic-broken rock boundary moves to the right in the Mohr diagram until the radial stress in the broken zone s equal to the radial stress in the elastic zone.

Jan 1, 1971

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By Edward W. Parker

One of the most important features of the coal-mining industry of the present day is one that is common to the majority of industrial enterprises—the substitution of mechanical methods for hand-labor.

Jan 1, 1900

SOUTHERN CALIFORNIA LOCAL. SECTION Executive Committee SEELEY W. MUDD, Chairman C. COLCOCK JONES, Vice-Chairman FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER In. order to make the meetings of the, Section more interesting and fruitful, the Executive Committee has formed a sub-committee on programs for. Section meetings, which announces for the coming autumn and winter season, four dinner meetings, at intervals of two months, in which the co-operation of all Section members is urgently. requested. The subjects chosen for discussion at these meetings, with the proposed dates, are as follows: Sept. 28, 1915. Mining Geology of Mojave County, Arizona. Dec. 14, 1915. General Geology and Mining Conditions in Southern California. Feb. 1, 1916. Petroleum, its Geology and Technology. April 4, 1916. General Mining Conditions in. South America. F. J. H.. MERRILL, Secretary.

Jan 10, 1915

By J. L. Wyatt

THE strain sensitivity, K, a property of metals defined as the unit change in electrical resistance per unit strain, was measured for commercial purity titanium wire to determine its usefulness as a strain gage material. A Kelvin double bridge, accurate to 0.000001 ohm, was used to make measurements from 0 to 1 pct total strain. A positive value of 0.17 for K was found. This compares with 2.15 for constantan and 3.5 for cold-worked invar, two of the more common strain gage materials. The effect of temperature also was determined. It was found that a change in temperature of 30°F caused the same resistance change as 1 pct strain. It is therefore concluded that titanium would have utility as a strain gage only if the thermal fluctuations in the specimen could be controlled to a high degree and in applications of very large total strain.

Jan 1, 1953

Would you give us a short biographical sketch including your birthplace, education and current activities? I was born Jan. 16, 1920 in Minneapolis, Minnesota, and lived there the first 22 years of my life. I also spent quite a bit of time on a farm about fifty miles north of Minneapolis owned by relatives. During the Depression, we lived off of ten cows and about fifty chickens. I'm a full-blooded Swede all along the line, and I'll be the last one in my family since my wife is not of Swedish descent. I attended Macalester College, a small school in St. Paul, to study for the ministry originally. However I soon realized that I really didn't have the talents for the ministry and I could probably do as much or more in a field where I did have some talent.

Jan 3, 1974

By P. W. George

This paper presents geological data regarding deposits of over 7,500,000 tons of fine-grained sulphide ore in barite gangue. A series of pyroclastics and arkoses was intruded by sills of quartz porphyry in connection with batholithic intrusions of granite 3 miles from Buchans. Gentle folding, with fracturing acid shearing of tuff beds and intruded quartz porphyry, accompanied and followed the intrusion of granite and porphyry. The sulphide-barite mineralization is localized primarily in fractured and sheared tuff beds, but also in the sheared quartz porphyry. Two structures have proved particularly favorable for mineralization-one, the center of an anticline; the other, a series of weak, incompetent tuff beds intruded by thin sills of quartz porphyry and located between strong beds of arkose. During the folding the weak tuff with intruded quartz porphyry was intensely sheared and contorted and subse-quently mineralized by sulphides and barite.

Jan 1, 1937

By Don M. Jackson

The techniques for the growth and controlled, graded doping of silicon epitaxial overgrowth layers were established. Grading of- impurities such as arsenic or boron in arbitrarily chosen profiles oiler four orders of magnitude (from I X 10Lg to 1 X 10L5 cm) was accomplished. The graded structures were grown in a stepwise manner where in the profiles were approximated by growing many separate layers with small doping-level changes between layers. Masked-area growth of silicon through windows in a SiO2 masking film was acconiplished through the simultaneous injection of HCl gas 102th Sic14 in the epitaxial reactor. The HCl served to inhihit the growth of silicon on the Sz02 surface, and also to control the cross-sectional profile of the silicon mesas. silicon from the substrate was etched out through the windows, and then epitaxial material was used to fill the holes hack in to form planar diodes. Simullaneous HCl injection was adapted to control the cross-section profile of the hack-filled regions. Arsenic-huried regions beneath in te- In recent months, the epitaxial growth process in semiconductor materials technology has evolved into a complex system directed at both material improvement for better monolithic integrated-circuit characteristics and the development of new silicon structures for future integrated-circuit needs. The advent of high-temperature HC1 gas etching1 grated-circuit transistors reduced V(SAT) by slightly more than one third, bringing this parame-ter to that of an isolated component transistor. When arsenic was diffused into the starting sub-stvate, it was necessary to remove any excess arsenic in order to avoid excessive audodoping of the subsequent epitaxial layer. Oxide isolation of single-crystal regions in a substrate provided complete electrical isolation of integrated-circuit components, thereby eliminating parasitic capacitance which is inherent in standard integrated-circuit processing. The process involved the etching of deep mesas on silicon Wafers, the formation of an oxide over the mesa surface, and then the deposition of several mils of polycrystalline silicon over the oxide. The original substrate was lapped and polished allay until the mesas were left isolated in the polycrys-talline matrix. The Final components were fabri-cated in the single-crystal islands. Speed and power-handling capabilities of standard circuits were improved through the process. wherein work-damaged material is removed from the surface of the silicon wafer just prior to the silicon deposition step has made it possible to grow silicon films with structural quality that approaches that of the substrate. HBr used in the same volume ratio as HC1 etches silicon at the same rate and with the same results as HC1. Recent developments in epitaxial materials technology have occurred in the areas of precise doping control, buried prediffused regions between over-

Jan 1, 1965

By J. B. Hiskey, W. J. Schlitt, W. G. Pitt

Aqueous SO2 (sulfurous acid) is an interesting chemical compound. It functions as a reagent in various hydrometallurgical systems, but also represents an undesirable constituent in gyro- and hydrometallurgical effluent solutions. When present in such streams, SO2 can be oxidized to the more stable sulfate form to avoid exsolution of SO2 as a source of fugitive emissions and to simplify standard water treatment plant operation. This study provides information on the stoichiometry, kinetics, and mechanism of SO2 oxidation using oxygen and an iron salt catalyst with solutions containing 0.05-20 g/L (0.002-0.7 oz per gal) SO2. The effects of iron salt concentration, oxygen pressure, temperature, degree of agitation, and pH on SO2 oxidation are also described.

Jan 1, 1984

By R. Taggart, D. H. Polonis, W. C. Gallaugher

In the Ti-Cu system, the a' phase can be produced over a wide range of alloy composition witJwut the retention of measurable amounts of the ß or ? phases. This paper reports on the decomposition of this hexagonal martensite phase front the standpoint of solute corzcentratiorz, tempering temperature, and coherency strain condition. The mechanism of precipitation during tempering comprises localized precipitation which is followed by discontinuous precipitation if sufficient coherency strains are present. The localized precipitation process in hypoeutectoid alloys is described by the generalized Johnson-hiehl equation and an activation energy of 46,000 cal per mole. In hypereutectoid alloys the corresponcEing activation energy is 51,000 cal per mole. The rate-controlling process has been proposed as the difision of copper along a' platelet interfnces. SEVERAL investigations have been reported concerning the kinetics of decomposition of the mar-tensitic a' phase in titanium binary alloys.' In the Ti-Mo system,' two modes of a' decomposition have been observed in the presence of /3 phase; one of these involves the precipitation of fine a from a', and the other involves diffusion across the a'-ß interface. In studies of the Ti-Cr system, Rostoker2 did not detect the formation of TiCr2 during tempering. In Ti-Ni alloys,3 the intermediate phase Ti2Ni has been found to precipitate directly from a' along the interfaces between plates. With the exception of the study of Ti-Ni alloys the previous investigations of tempering phenomena in substitutional martensites are mainly qualitative and do not present a detailed description of the precipitation processes. The following limitations restrict the correlation of the microstruc-tural processes and reaction kinetics during tempering in most binary-alloy systems. 1) A mixture of at least two phases characterizes the constitution of quenched alloys. 2) Difficulties have been encountered in obtaining uniform structures throughout quenched samples. 3) The reaction products, and in particular their morphology. have not been clearly resolved. 4) The martensitic a' phase forms over only a limited composition range for most titanium-base binary alloys. Gomez and polonis4 showed that the Ti-Cu system provides an excellent basis for investigating the tempering of a' over a range of composition without the complication of retained P or the transition w phase. In the present work the effects of solute concentration, tempering temperature, and coherency strain conditions are considered with reference to the over-all precipitation process in quenched alloys of the Ti-Cu system. Both microstructural observations and kinetic data are correlated to define the rate-controlling processes which govern the observed localized and discontinuous precipitation reactions. An earlier paper5 was devoted to a discussion of the modes of heterogeneous nucleation of Ti2Cu from the martensitic a' structure. The present paper will therefore emphasize the progress of the tempering reaction beyond the initial stages. EXPERIMENTAL METHODS The Ti-Cu alloys for this study were prepared by conventional arc-melting procedures. Chemical analysis revealed that the alloy buttons contained approximately 0.02 wt pct 0, 0.04 wt pct N, and within 0.1 wt pct of the intended copper concentration. The progress of the tempering reaction was followed by means of electrical-resistance measurements utilizing a Kelvin double bridge, microhard-ness readings with a 400-g load, and X-ray dif-fractometry patterns to reveal line-broadening effects. Metallographic specimens examined at magnifications greater than X1000 were shadowed with germanium to reveal fine structural details. Direct carbon replicas were prepared for the electron-microscopy studies. EXPERIMENTAL RESULTS Property Changes. The changes of microhardness that accompany the precipitation of Ti2Cu from a' are shown in Figs. 1 and 2. As the solute concentration increases the peak hardness, for a given tempering temperature, increases. In alloys of given composition the time to reach the peak hardness agreed with the time to attain maximum X-ray diffraction peak breadth, as shown in Fig. 3. The maximum hardness and the maximum line breadth increased with lower tempering temperatures, and the time to reach the maximum also increased. The a' peaks broadened during the initial stages of tem-

Jan 1, 1965

By G. H. K. Schenck, H. W. Robinson

Private weather forecasting services available on a contract basis can significantly reduce the uncertainty associated with weather-induced changes in mineral production and demand. Such services offer the mineral producer the opportunity for tactical and strategic response to weather conditions. There are at least 50 private meteorological consulting services as well as numerous individual meteorology consultants. Fees for services range from $150-$600 per day for one man to over $20,000 per month where a complex forecasting or modification program is undertaken.

Jan 1, 1971

By O. E. Palasvirta

Close examination of most so-called new processes in mineral dressing reveals that they were conceived and developed a long time ago. High-intensity magnetic separation is no exception. Although its application in iron ore beneficiation seems new, in Germany the process has been commercially successful for almost two decades. High-intensity separators have long been standard equipment in the glass sand industry; they have also been used in concentrating some of the more unusual paramagnetic minerals. The basic features of an induced-rotor, high-intensity magnetic separator were described by Désiré Korda in Paris in 1905,1 and many patents have since been issued for improvements on the original design. Fig. 1 shows the basic design of an induced-rotor separator. Several U. S. manufacturers have been supplying induced-rotor separators for many years, but these are all devices of relatively low capacity, not suitable for treating such low-cost commodities as iron ore. On the other hand, two German manufacturers are offering induced-rotor separators of high capacity, both proven in the field.

Jan 12, 1959

By Nicholas J. Grant, Oliver Preston

A series of dilute solid solutions of a1uminum and silicon in copper, in powder -form, were internally oxidized, compacted, and extruded, to produce Cu-A12O3 and Cu-SiO2 alloys with 0.1 to 12 vol pct of oxide. Room-temperature tensile tests, creep-rupture tests from 450oto 850°C. conductivity measurements, and recrys-tallzzation studies were made. Oxide particle size and interparticle spacings were determined in an effort to relate the structure to measured strength values by means of known dispersion strengthening theories. A new dispersion strengthening theory, based on the effect of the dispersed phase on the retention of strain energy from the deformation step, zs proposed for this type of alloy, THE study of dispersion strengthening is of partitular interest in high-temperature materials technology in view of the excellent creep-rupture Properties and thermal stability achieved with SAP.1-5 Considerable effort has been devoted to this study in recent years, and encouraging results have been obtained in a number of systems.6 In general, the most

Jan 1, 1962

By J. F Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

By J. F. Haseman, J. E. Davenport

In the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1,2 results in inadequate beneficiation. Investigation of Flotation Methods Flotation has been used in 'Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate. 3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P2O5 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P2O5, 20; SiO2, 40; CaO, 29; Fe2O3, 2; Al2O3, 3; F, 2.3. The particle-

Jan 1, 1948

EXPLORATION U.S. 4,065,972 - Exploration for subsurface ore bodies of uranium. mercury or other inorganic or organic minerals having specific gases associated thereto Small gas sample containers are planted in a plurality of shallow holes in the surface of the earth in a predetermined pattern and left in place for a period of time sufficient to collect migrating gases. Each container includes a gas collection chamber and means for admitting gases at a predetermined flow rate. Strips of detector material which is sensitive to specific gases are mounted in the collection chamber. Recovered containers are subjected to qualitative and quantitative analysis. F. W Holub and H. W. Alter, assigned to Terradex Corp Jan. 3, 1978. 9 pp (73-421 5R) Filed 5-24-76 (689,710) Same. British 1,498,737, dated Jan. 25, 1978

Jan 1, 1979

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sigurdson

CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO2, as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilmenite. It has also been referred to as arizonite because in chemical composition it resembles an occurrence in Arizona which was described by Palmer1 in 1909.

Jan 8, 1954

By Hsun Hu

The microstructural changes during rolling and at various stages of recrystallization in (111)[112] oriented single crystals of Si-Fe have been studied by transmission electron microscopy. At very low deformation, the dislocation structure consists of jogged dislocation lines, edge dislocation dipoles, and numerous dislocation loops, which may be interpreted by the jog-formation mechanism in moving screw dislocations. Up to 70 pct rolling reduction, no sharply defined cells are formed. Subgrain forma- tion takes place somewhat earlier in the annealing process than in a similarly processed (110)[001] crystal. This may be partly responsible for the reported difference in the rate of recrystallization between (111)[112] and (110)[001] crystals. Evidence indicates that the formation of recrystallization nuclei occurs largely by the coalescence of sub -grains. This is consistent with previous observations on other Si-Fe crystals. AVAILABLE data in the literature indicate that the main features of rolling and annealing textures in (111)[112] and (110)[001] crystals are essentially similar. A (111)[112] or (111)[112] crystal can be rolled 70 pct without changing its initial orienta-

Jan 1, 1964

By A. A. Collins

OF widespread interest to all lead metallurgists is a dross smelting process that will consistently give mattes and speiss of low lead and high copper contents. It is a problem that has intrigued operators through the years. In the past few years, with increased amounts of copper and overcrowded metallurgical furnaces, it has been almost imperative to evolve some method. Experience at El Paso has shown that high copper-to-lead ratios can be consistently attained by use of the new soda process. † Older Methods Three older methods, i.e., 1. Dross plus siliceous ore and limestone. 2. Dross plus one fourth blast-furnace speiss and siliceous ore, 3. Dross plus sulphides and siliceous ore and scrap iron, do not give consistent results and the products are higher in lead and lower in copper than those produced with the soda process. Any radical changes in the blast-furnace drosses will throw any of these older methods into a tailspin. For almost ten years, El Paso used the third method, with varying results. It was noted that as the arsenic and anti- mony contents of the dross increased, the speiss and matte steadily increased in lead and decreased in copper. A dross containing four parts of copper to one part of arsenic was considered to be ideal. At times this balance of copper to arsenic was almost impossible to obtain, especially when handling copper Cottrell dusts, which vary so greatly in copper and arsenic. Custom smelters like El Paso, handling a great variety of dusts, concentrates and ores, are apt to have anywhere from I to 15 pct copper on charge, with a variable in arsenic of from 0.5 to 2 pct. With such conditions, and drosses varying from 12 to 40 pct copper, an operator using the older dross reverberatory practices would find it just about impossible to control the reverberatory operations and to produce a good product low in lead and high in copper. These conditions prevailed at El Paso from the year 1940 to the present. In May 1942 it was decided to experiment with the soda process. The Soda Process After considerable work the soda method was finally evolved to the present state. It has never failed to produce a good product even under the most adverse conditions. It might be well to remember that many men of thought in the smelting industry have at one time or other sugge~ted the removal of all copper, arsenic and antimony from the lead blast-furnace charge as an aid to better metallurgy.

Jan 1, 1949