Search Documents

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By John L. Lamont, Walter Crafts

SECONDARY hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to the secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at 1100°F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader.3 Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to 1100°F, but the mechanism of the process has received little consideration .

Jan 1, 1948

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1937

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1938

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee

Jan 1, 1943

Recognizing the fact that the problems of the committee named by the Board to prepare the "official ticket" for officers ' and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee.

Jan 1, 1944

By O. D. Sherby, J. L. Lytton, C. R. Barrett

Randomly oriented polycryslalline copper of 99.995 pcl was tested in tension at temperatures of 626o, 496o, and 406o. The gvain-size mnge investigated was from 0.03 to 0.7 mm. Grain sizes were produced by two techniques: 1) varying the amount of prior cold work and the amealing time at constant annealing temperature so as to obtain various vecrystallized grain sizes with minimum grain growth, and 4 holding the prior cold work constant while varying the annealing time or temperature so as to obtain varying grain sizes by grain growth. Polycrystalline samples (grain size of 0.03 mm) with a strong. [001](100) texture were also studied. The relationship between the steady-state creep rate, Es, and pain size was found to be the same indepentent of the technique used to prepare the various grain sizes. For specimens with grain diameters above about 0.1 mm ea zuas esse)ztiallj~ independent of grain size, while for smaller grain diameters Cs increased slightly with decreasing grain size. Strongly textured polycrystalline copper, which contained low-angle grain boundaries, exhibited steady-state creep rates that were slightly lower than those observed in randomly oriented copper, of the same gain size. The results are explained by conside?%ng- the contribution of grain boundary shearing to the total strain and the effect of grain size on the resulting creep substructure. EXPERIMENTAL observations concerning the influence of grain size on steady-state creep rates are varied and oftentimes conflicting. Numerous early investigators found that an increase in the grain size resulted in a decrease in the high-temperature steady-state creep rate, i,.'-" Other workers have foundthat ef decreases with increasing grain size up to some optimum grain size and then increases with a further increase in grain size.'- '' It has been suggested that es, decreases with an increase in grain size only because the range of grain sizes studied normally lies to the left of the grain size for optimum creep resistance. However, sherbyl2 and Feltham and his co-worker13, 14 have found that even for small grain sizes 2, does not always decrease with an increase in grain diameter but may be proportional to the square of the grain diameter. A possible explanation for the different creep rate-grain size relationships which have been observed is that in most experimental studies different grain sizes have been prepared by annealing at various temperatures. For metals in which the impurity concentration is high (greater than about 0.1 at. pct) this type of

Jan 1, 1968

By W. Crafts, J. L. Lamont

Secondary hardening in tempering has long been recognized as a typical characteristic of steels containing large amounts of carbide-forming alloys. These steels, when quenched and tempered, tend to soften somewhat after tempering at low temperatures, and to reharden at intermediate tempering temperatures before finally softening to low hardness. This behavior in tempering has been studied by many investigators, chiefly with respect to thc secondary hardening of high-speed steels. The initial softening has usually been ascribed to decomposition of martensite and growth of iron carbide particles. The secondary hardening has been explained by formation of fresh martensite from residual austenite, formation of very fine alloy carbide particles and by precipitation hardening of metallic compounds in the ferritic matrix. However, factors derived for the calculation of tempered hardness in low-alloy steels1 indicated only a tendency toward retarded softening rather than a discontinuous rehardening. A study was, therefore, made to determine whether fresh martensite from residual austenite and precipitation hardening are essential to rehardening and the degree to which tempered martensite could be rehardened by precipitation of alloy carbides. The mechanism of carbide rehardening was also investigated to determine the nature of the process. The causes of secondary hardening in high-speed steel have received serious consideration for about thirty years. Among the earlier workers Bain and Jeffries2 in 1923 recognized residual austenite as a significant factor, but in addition, emphasized the effect of the formation of alloy carbide particles of "critical" size. They conceived that freshly quenched martensite forms low-alloy iron carbide at low tempering temperatures; with further tempering the iron carbide is then modified by alloying elements that can diffuse most readily at intermediate temperatures (850°F); and that the iron carbides grow in size by coalescence so that the steel tends to lose hardness. At higher tempering temperatures carbide stability rather than alloy availability becomes the controlling influence and in high-speed steel "iron-tungsten carbide is the most stable one and forms to the elimination of the earlier formed carbides. . . . The iron-tungsten carbide particles reach approximately the size for critical dispersion after a short reheat at II00 F." This concept, the formation of alloy carbide nuclei, redissolving of the iron carbide, and diffusion of carbon to the alloy carbide, was restated for vanadium steel in 1932 by Houdremont, Bennek, and Schrader. Subsequent studies have confirmed that iron carbide changes to alloy carbide at 1000 to IIOOOF, but the mechanism of the process has received little consideration.

Jan 1, 1949

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By I. C. Edwards, G. E. Agar

INTRODUCTION Many research efforts over the past years have been devoted to the study of energy consumption in comminution and the characteristics of the broken material. The old "laws" have been superseded by more general methods of analysis1,2,3 but these methods have not received much attention outside the laboratory. The work to be described here was done in order to obtain scale-up information on wet rod milling of sylvinite. EXPERIMENTAL A 30 x 51 in. Denver rod mill with a scoop feeder was used for these tests. Ore was fed from a variable speed screw conveyor into the feed box along with saturated brine. The mill was filled to approximately 45% of its volume with 2400 lbs of a mixed rod charge. The minimum possible feed rate was 2.5 tph and the practical maximum for this mill was 8 tph. Individual tests were run by setting the solid feed rate, then adjusting the brine flow rate to give the desired pulp density. After steady state, as evidenced by constant discharge pulp density, had been reached, samples of the discharge were taken at 15-minute intervals. These samples were filtered, washed with alcohol, dried, then screened on Tyler screens using a Ro-tap shaker. The sylvinite feed was regular plant feed that had been scalped at 20 mesh and was tapped from the coarse ore bins. It had been previously passed through a roll crusher set at 3 inches and after scalping was essentially minus 1 in. plus 20 mesh. RESULTS The screen analysis of samples from each series of tests was plotted on double logarithmic scale paper to determine the reliability of the series. In some cases, a faulty sample or screening procedure dictated that the results of one test be discarded. The criterion is a simple one — if the slope of one plot was noticeably different from the others in the series, it was discarded. The only cases that caused difficulty were those in which the brine was not thoroughly displaced from the solids. When this occurred agglomerates were easily identified on the screens and the whole of the sample was retained on 3 or 4 screens. There were no border line cases. The number N given in Table 1 is the number of size analyses that were pooled to form the data shown in Fig. 1. While examining the reliability of the sizing and sampling by plotting the data, it became apparent that there was no significant difference between grinds made at 50 and 60% solids. For the analysis given here, these tests were regarded

Jan 1, 1967

By Clifford Frondel

THE aluminum oxide known as corundum has several varieties that have been used as gem materials since ancient times. These include the red variety called ruby, the blue variety sapphire, and the asteriated types of ruby and sapphire. Asteriated sapphire was known to the ancients under the name of astrios, and descriptions of this gem were given by Pliny and other early writers. The relation of these gem materials to each other as varieties of a single species, corundum, was first clearly established by Haüy in 1805 and J. M. Güthe1 in 1809. Natural gem corundum is obtained principally in Ceylon, Siam, Burma, India, and Australia. Star sapphires and rubies always have been highly prized and in recent years have become particularly popular in the United States. Natural star rubies of large size and fine quality are extremely rare and rank with large and fine emeralds and diamonds as the most valuable of gem stones. Interest thus attaches to the recent success in commercially synthesizing star sapphires and rubies of a size and perfection unmatched by nature.

Jan 1, 1954

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device. When the management decided to start open- pit operations in 1945 the ruggedness of the terrain was one factor that led to the purchase of the small 22-T model drill. The orebody lies on both sides of Copper Creek Canyon. The sides of the canyon are steep and are cut by numerous narrow branch gullies. The drill had to travel over roads that were narrow and steep. It proved adequate for drilling the capping formation and is still in use.

Jan 1, 1950

By D. W. Fuerstenau

The United States is rapidly approaching an acute shortage of minerals. According to some observers, this situation may even be more severe than the energy crisis because the US consumes nearly 30% of the world's mineral production. With the mounting competition for world mineral supplies, we can no longer take for granted that foreign mineral products will be available to the US as abundantly as in the past. In 1973, US consumption of mineral raw materials was $35 billion. Of this, $7 billion consisted of imports. Without a drastic reorientation towards the mining of domestic mineral resources, the 1973 $7 billion deficit might mushroom to $100 billion by the year 2000. Thus, a return to domestic sources of raw materials will become absolutely necessary-and will be bucking the trend of the past 25 years, characterized by capital investment for growth in multinational overseas mining operations.

Jan 11, 1975

By N. H. Cone

It is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

By N. E. Cone

IT is somewhat surprising that among the many mechanical devices that were brought into the State of Colorado, that the Brückner cylinders alone have stood the test for roasting ores. The brick walls of the Arey and Stetefeld furnaces have been remodelled into reverberatories and compound reverberatories, their binding and anchor irons have been forged into hoes and shovels, while the Crosby and Thompson cylinders have been rent by the ruthless hand of the foundryman searching for a tough piece of boiler plate. Two only of these furnaces remain in operation, of the large stock that came into Colorado by car-loads several years ago, and they occupy only a subordinate position to some reverberatories on the North Boulder Creek. But to-day there are in Colorado, in active operation, ten Brückner cylinders, and two or three more running part of the time. Dur-

Jan 1, 1876

By B. W. Levinger

THE system Ti-CI- has been studied by several investigators." ' Though titanium and chromium are completely miscible at high temperatures, an intermediate phase of the approximate atomic proportions TiCr, has been identified at various compositions between 60 and 68 wt pct Cr. The structure of this phase was established as the cubic C15 (MgCu2) type with 24 atoms per unit cell and a lattice parameter 6.929 kX.2 During a study of the ternary system, Ti-Mo-Cr,5 the existence of a high temperature modification of the TiCr, phase was discovered. In a series of alloys annealed at 1300°C and containing from 60 to 70 wt pct Cr and 5 pct Mo, a new phase was present which did not correspond to either ß solid solution or TiCr,. By trial, the new phase was identified to be of the hexagonal C14 (MgZn2) structure with 12 atoms per unit cell. Further work showed that the hexagonal structure was. in fact, also present in binary Ti-Cr alloys quenched from high temperatures. To make the identification more certain, the intensities of the various reflections were calculated assuming a composition TiCr2 and C14 structure. Table I lists reflection planes, interplanar distances, calculated intensities, and a comparison of these values with the lines of a binary Ti-Cr alloy (66 pct Cr) annealed for 20 min at 1385°C and water quenched. Since high angle lines were more diffuse, the correspondence between visually observed and calculated intensities was not as good at these angles. Lattice parameters were computed to be a = 4.922 kX, c = 7.945, c/a :- 1.614. The corresponding interatomic distances are: titanium to titanium distance, 3.00:, kx, chromium to chromium distance, 2.43, kX, titanium to chromium distance, 2.88,, kX. These compare to 3.00, 2.45, and 2.87 kX in the cubic phase, respectively.' The atomic positions in the C14 structure are as follows: Titanium 1/3, 2/3, Z; 1/3, 2/3, 1/2: 2/3, 1/3, i; 2/3, 1/3, (1/2-z); Chromium 0, 0, 0: 0, 0, 1/2; 2x, 2, 1/4; 232, x, %; X, 22, 1/4; X, 2x, 3/4; x. x, 1/4; x, x, 3/4; The values of x and z were calculated for the alloy mentioned and found as follows: z — 0.061, x = 0.165. The values assumed in the intensity calculations were those for an ideal close-packed lattice or z = 1/16, x = 1/6. Work in the Ti-Mo-Cr system indicates that y2 the hexagonal modification of TiCr2, is the stable phase above 1300°C, while y1 with the cubic structure is stable below 1000°C. X-ray examination of a number of alloys annealed at intermediate temperatures showed that the hexagonal and cubic phases can coexist. Alloys quenched from 1000°C and annealed at 1100" and 1200°C showed small amounts of y2 at the higher temperature. A considerable amount of y, seemed present, however, in cast alloys annealed at 1100°C. It further appears that there is a small but definite solubility range for both phases in the ternary system. Acknowledgment The results of this paper represent work carried out in conjunction with a project sponsored by Watertown Arsenal, Contract No. DA-11-022-ORD-272. References 'M. K. McQuillan: Journal Inst. Metals (1951) 79, p. 379. 2 P. Duwez and J. L. Taylor: Trans. ASM (1952) 44, p. 495. W. J. Van Thyne,. H.. D. Kessler, and M. Hansen: Trans. ASM (1952) 44, p. 974. 1 F. B. Cuff, N. J. Grant, and C. F. Floe: Trans. AIME (1952) 194, p. 848; Journal of Metals (August 1952). Unpublished Research, Armour Research Foundation. "H. J. Wallbaum: Ztsch. Krist. 103, p. 391.

Jan 1, 1954

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952