Search Documents

By Jacob H. Masliyah

The dynamic simulation of a gravity separation vessel (a high throughput classifier) has been developed. The feed slurry was assumed to contain light (oil droplets) and heavy (mineral solids) particulates of various size. The feed slurry was characterized by the particle size distribution of both the light and the heavy particles. The equations describing the slip velocity for each specie and those defining the time variation of each specie concentration were solved implicitly using Runge-Kutta algorithm. The dynamic simulation was capable of predicting the movement of the froth layer and the density variation of the under- flow. Field data are in agreement with the simulation model and it is shown how this model could be used to develop a control strategy.

Jan 1, 1984

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By R. E. Maringer, B. A. Wilcox, A. H. Clauer, J. H. Sovik

Internal friction measurements from 25° to 1100°C have been made on specimens machined from TD nickel bar. The use of miniature torsional pendulum specimens alloived damping measurements to be made on specimens whose axes were parallel to the original bar axis, at 45 deg to the bar axis, and at 90 deg to the bar axis. There was a marked difference in damping with varying specimen orientation, and this was related to the pronounced micro structural anisotropy of this material. Varying the microstructure by cold working plus re crystallization annealing also greatly affected the damping behavior. Recrystallization essentially removed the broad peak found at 400° to 650°C in as-received TD nickel, and in addition greatly lowered the background damping. DlSPERSION hardened metals such as SAP-type alloys (Al + AI2O3) and TD nickel (Ni + 2 pet ThO2) have been developed primarily to improve high temperature strength properties. There have been numerous damping studies on SAP-type alloys,1"9 and one of these6 showed that the damping capacity was greater than that of 99.5 pet pure Al from 25° to 600°C. Several preliminary observations on TD nickel10 and an experimental Ni-ThO2 alloy11 indicated that here, too, the damping capacity was quite high. A high damping capacity in TD nickel, combined with its relatively good high temperature creep strength, could provide an additional benefit for some high temperature structural applications. This work was undertaken to study the internal friction behavior of TD nickel bar over the temperature range 25° to 1100°C. In Ni-ThO2 and Ni-Cr-ThOz alloys, other properties such as steady-state creep rate,12 creep rupture life,12'13 modulus of elasticity,14 and ultimate tensile strength,14 are sensitive to orientation with respect to the primary working direction. Thus, in order to examine anisotropy effects in damping, studies were made on specimens machined with their axes parallel, at 45 deg, and transverse to the original bar axis. MATERIAL DESCRIPTION AND EXPERIMENTAL PROCEDURES The material used in this investigation was from the same £ in. diam TD nickel bar that has been studied previously.13'15 The structure typical of the as-received TD nickel is shown in Fig. 1, and additional details of the structure can be found in Refs. 13 and 15. Elongated grains are parallel to the bar axis and are about 10 to 15 u long and about 1 u in diam. This structure is very stable, since no recrys-tallization or grain growth occurred after annealing for 3 hr at 1300°C.13 The total ThO2 content was 2.3 vol pct and the particles ranged in diameter from 100 to 1000. The average particle diameter was 370Å and the mean planar center-to-center particle spacing was 2340Å. To examine the influence of grain and subgrain structure on damping, a section of TD nickel bar was swaged and drawn at room temperature from 1/2 in. diam bar to 0.040 in. diam wire (99.3 pct re-duction in area). The structure in Fig. 2 resulted after the wire was annealed for 3 hr at 1250°C. The recrystallized grains were much larger than the grains in as-received bar, but still showed considerable elongation in the direction of working. A high

Jan 1, 1970

His face wreathed in smiles, J. Richard Lucas, Chairman of the Keynote Session, conceded that "the papers appeared to have been of some interest." This was a modest description of the opening day of technical sessions at the SME Fall Meeting and Exhibition, October 13 to 15, in Tampa, Fla. The auditorium had capacity for 800 spectators and there was hardly a vacant seat visible. The topic, Resource Development of the Fertilizer Minerals, was covered in four authoritative papers. H. S. Ten Eyck set the stage. Resources are always viewed in relation to future requirements, and these depend largely on population. If the population trend continues, the world's 3.3 billion people will increase to 6.7 billion people by the year 2000. About 70% of this increased population will be in developing areas which are not capable of supplying sufficient food and fiber for their needs. Fertilizer is a means of bridging the crop shortage. Projections of fertilizer requirements by 1970 are from 53 million to 67.5 million long tons of plant nutrient which compares with 1964 consumption of 37.7 million tons. Looking ahead to 1980, the growth continues with an estimated demand of 80 million to 113 million tons combined of N P and K.

Jan 12, 1966

By W. P. Sykes

TUNGSTEN serves mankind in two major roles. The first of these is represented by the tungsten filament of the incandescent electric lamp, a common article of commerce. In the field of hard alloys it plays its second substantial part. A fortunate combination of physical properties in this metal ac- counts for its efficient service as a source of illumination. Tungsten melts at about 3400°C, has a relatively low vapor pressure and at the same time sufficient strength, both hot and cold, to serve satisfactorily as filaments, which may range in diameter from 0.060 to 0.0005 in. In the early days of the incandescent lamp, the pioneers realized the importance of using a substance of high melting point for the source of light. The metals osmium (mp approx. 2700°C) and tantalum (mp approx. 2850°C) were both employed to some extent. Tantalum actually attained some commercial importance in this field because it could be drawn into small wires of appreciable length. DUCTILE TUNGSTEN WIRE Before the year 1908, tungsten was considered a nonductile metal, since no one had succeeded in overcoming the brittleness so typical of the unworked metal at room temperature. The methods employed today in producing ductile tungsten wire were developed over a period of years. The process was largely determined by the exceedingly high temperature required to melt this metal. Even today the difficulties involved in producing an appreciable quantity of pure

Jan 1, 1953

By R. W. Olson, A. L. Benham

Viscous fingering was studied as it occurred in an open Hele-Shaw model (1 ft x 4 ft x 1/16 in.); it was also studied in the same model packed with 80-mesh glass beads during miscible displacements under unfavorable viscosity ratio conditions. It was determined that the lengths of 20 elements of the front were distributed normally around the average position of the combined elements under all conditions. Represented by the normal distribution, the length of the viscous fingers grew linearly with the distance traveled from the point of finger formation, increased with displacement velocity, and increased with increasing mobility ratio. Results obtained during the first few inches of displacement were of little or no use in predicting finger growth and/or finger length throughout the 4-ft model since the point of finger initiation cannot be predicted and would often occur several inches from the point of injection with either positive or apparent negative coordinates. The fingering occurring during a miscible slug displacement was much greater than would be predicted based upon the actual mobility ratios between in-place fluid and slug and between slug and following fluid, using the results described above for miscible displacement in the absence of a slug. Many of the experiments in the packed model showed that the rate of growth of the viscous fingers was diminishing toward the end of the displacement in the 4-ft long model, indicating that microscopic mixing, such as diffusion or dispersion, was decreasing the viscous fingering effect. INTRODUCTION Viscous fingering is a manifestation of a finger-shaped interface between displaced and displacing fluids occurring during typical miscible displacement projects for oil recovery. Its cause may be traced to the instability of a viscous fluid being displaced by a more mobile fluid. Viscous fingering takes on important significance in the miscible slug process 1.2 where it may be a dominant factor in determining minimum slug size. Experimental1-3 and theoretical4-7 studies of viscous fingering have been made by other investi- gators. However, an exhaustive study of the variables affecting viscous fingering had not been made. The present study was undertaken in an effort to determine the effects of some of the more obvious variables—such as mobility ratio, displacement velocity, distance displaced, and packing—upon viscous finger length and growth in a small laboratory model. It does not necessarily follow that conclusions reached by studying the results of this model study may be applied to the field. Future studies would have to evaluate the effect of model size on extension of these results. EQUIPMENT AND EXPERIMENTAL PROCEDURES A flow diagram for the equipment used in this study is shown in Fig. 1. Basically, it consisted of (1) a constant-rate pump for the injection of displacing fluid into (2) a model made up of two flat transparent plates spaced a small distance apart and (3) provisions for the production of fluid into a calibrated graduate. The displacing fluid contained a dye which allowed visual observation of finger spacing and length. The pump performed at rates from 2.5 cc/hr to 480 cc/hr, while pumping a light mineral oil into a bladder in a closed glass container holding the displacing fluid. The model was made up of two plates of 1-in. Plexiglass with dimensions 1-ft wide by 4-ft long. These were spaced 1/16 in. apart so that the internal model dimensions were 1-ft wide x 4-ft long x 1/16

By Robert J. Alberts

Our shop started up in April of 1969, and during its 8th month of operation produced over 300,000 tons. Production continued to increase, and by January of 1970 tonnage rates significantly above 300,000 tons per month were being realized. Ours is a three vessel shop, producing 200 ton heats, with a normal grade breakdown indicating more than one half semi-killed carbon steel, with the balance distributed over rimmed and capped steel, alloy steel, killed carbon, and special killed drawing quality steel. The recent christening of a continuous billet caster has dictated that close to a quarter of our liquid steel be delivered to the caster.

Jan 1, 1972

By Alf Holmelid

Until recently the only automatic control of electric parameters in submerged-arc furnaces has been electrode control with electrode current or electrode impendance as controlled variables. Elkem Research and Development Centre has delivered this kind of control for a long time, both stand- alone controllers and control algorithms incorporated in an integrated computer control system. In recent years we have noticed increasing interest in more sophisticated electric control. Results both from pilot-plant experiments and from production furnaces show that proper electric conditions in the furnace are more important to the furnace operation than was assumed earlier. Optimal electric conditions lead to lower power consumption per ton of metal and allow use of cheaper raw materials Besides, power contracts and the market situation lead to more frequent change of load on the furnaces. Therefore it is important to vary the load in a way that allows proper electric conditions to be maintained. Based on this renewed interest in electric control, Elkem Research and Development Centre has carried out a project, starting with analysis of existing electric instrumentation and control algorithms for electrode control, and ending up with an integrated electric control strategy including power-demand control as shown in Figure 1. In this paper we will give a resume of this work and present a new integrated control strategy put into operation for the first time in June 1983. [ ]

Jan 1, 1984

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By AIME AIME

[The American Institute of -Mining Engineers does not assume responsibility for any statement of fact or opinion advanced in its papers or discussions.] A detailed list of the' papers contained in this section is given in the Table of Contents, pages i. and ii. Comments or criticisms upon all papers given in this section whether private corrections of typographical or other errors or communications for publication as "Discussions," or independent papers on the same or a related subject, are earnestly invited. ERRATA. The following corrections and. additions to papers contained in Bi-Monthly Bulletin No. 7, January, 1906,-were received too late for incorporation in the text of said papers ; but will be introduced in their: proper places: in the volume of the Transactions: These corrections are here published in order to bring them -promptly to the notice of the Institute. Page Line Cover, title-page and at the top of pages in the preliminary section "No. 1 " should be "No. 7 ". 1. Bottom For :" Dr. P. H. Shimer" read "Dr. P. W. Shinier " 69. Fig. 3. "N" of compass-record should be ?S". A new block for this illustration has been made as shown on p. xxxviii of this Bulletin. 78. 3 from bottom. For " slope " read " stope." 89. Fig. 2, small diagram in upper left-hand corner. Omit use 50 ft. to 1" scale ". For "Thro' 250 " read " Thro' 200 ". Add dotted line extend¬ing from upper right-hand corner of the square

Mar 1, 1906

By K. J. Edmiston, R. C. Kellner

Shortly after production was begun at the Duval Sierrita concentrator in February 1970, it became evident that difficulties would be experienced in reaching the designed operating level of 72,000 stpd. Since the major restrictions to production resided in the reduction crushing system, a comprehensive program was initiated to evaluate and optimize all crusher parameters affecting production. Positive relationships were established between production rate and crusher power draught, mantle support pressure, crusher setting, and crusher throw. Other parameters evaluated were the effects of feed distribution, crusher speed, mantle and concave configuration, choke feeding, and ore type. In order to obtain maximum production, it was also imperative that the mechanical integrity of the crushers be improved. Therefore, redesign of nearly the entire crusher assemblage, including such items as the top shell, bushings, and the mantle hydraulic support system, was required. In addition, automatic control stategies were evaluated and detailed operating guidelines were established. As a result of this extensive crusher examination, the limitation on plant throughput has been shifted to the grinding section, and a monthly average production level of 86,000 stpd is currently achieved. Programs under current evaluation are aimed at further increasing capacity to exceed 90,000 stpd.

Jan 1, 1976

By T. E. Wayland

The general geology and mineralogy of bentonite, including pertinent technological details of clay minerals in the montmorillonite group, are summarized. Worldwide occurrences of bentonite deposits are reviewed, with emphasis on geologic methods and economic principles of evaluation. Active mining districts are described and areas with potential for current and future development are assessed. The production history of bentonite, principal producers, major consumers, and indicated trends are noted; also attention is directed to the hundreds of minor industrial uses of this versatile material, ranging from the manufacture of (A)cid neutralizers to (Z)eolite water softeners. Recent significant results of both basic and applied research are reported, with suggested lines of investigation for current and near-future consideration.

Jan 1, 1972

By A. C. Fieldner

COKE and by-products have prime importance in the war program. The past year was marked by the construction of new and the rehabilitation of old by-product and beehive ovens and by the increase of production from existing plants to practically 100 per cent capacity. W. T. Brown's paper, "Plan to Improve Blast-Furnace Coke," presented at the Fuels Conference in St. Louis, Sept. 30, showed how the blending of low- and high-volatile coal improved the physical properties of coke and that improvement of the quality and uniformity of coke favored an increase of blast-furnace capacity- a vital need in the war program. Others in the industry have likewise increased production of coke or recovery of by- products by various innovations or changes in operation. Recognition of the value of pooling these developments for the benefit of the entire industry led to organization of a survey of coke- oven plants and blast furnaces by the Bureau of Mines in co-operation with the Solid Fuels Co-ordinator with a view to improving metallurgical coke production and recovery of by-products. This survey is being conducted with the help of an advisory committee consisting of representatives of the Bureau of Mines, the Solid Fuels Co-ordinator, the War Production Board, and the blast-furnace, coke-oven, and coal-mining industries.

Jan 1, 1943

By F. D. Dietiker

After determination of the requirements for a given application, proper selection of a belt conveyor is made from tables and formulas commonly used by conveyor designers. Belt conveyors, which are universally accepted as a means of transporting bulk materials, also perform the important functions of stockpiling and reclaiming.

Jan 1, 1978

By Satyajeet Ghosh, Edward F. Glynn

Many of the proposed techniques for calculating the reliability of rock slopes utilize Monte Carlo simulation. Monte Carlo approaches are attractive because they provide means of solving probabilistic problems with deterministic algorithms. One disadvantage shared by all simulation-based stability analyses is that they assume all the random variables are independently distributed. The paper focuses on the independence assumption and examines the effect of correlation on the probability of failure. In particular it considers the influence of possible (albeit hypothetical) correlation between joint attitudes [(8)] and joint friction angles [($)]. The study indicates that neglecting correlation can introduce significant errors into the reliability computations. With a modest positive correlation between [8] and [$] the error can lead to a 100% overestimate of the probability of failure.

Jan 1, 1982

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

By Elburt F. Osborn

The phrase "Clean Synthetic Fluid Fuels From Coal," implies that it is possible to obtain adequate and dependable supplies of fuel without sacrificing the quality of our air, water, and land. Because of the long lead times needed to develop technical feasibility, into commercial reality, however, vigorous efforts must be made now in order to do it. The available options for clean fuels include many exotic sources, like solar and geothermal power, fuel cells, and thermionic and thermoelectric systems. To solve the energy crisis, however, we have three basic energy criteria-abundance, reliability, and commercial availability by 1985. Only processes based on converting coal and oil shale to clean, synthetic fluid fuels can meet all three.

Jan 9, 1974

By W. J. West, T. D. Mueller, J. E. Warren

The authors have presented valuable information on the influence of the interfacial tension and the contact angle on the recovery efficiency of the waterdrive process. It is considered, however, that the following points deserve a closer examination. 1. As pointed out by Wyllie and Spangler1 the displacement pressure PD i.e. the pressure required to initiate the displacement of the wetting phase from the core, is a measure of the maximum pore diameter dmax. If the capillary pressure Pe as a function of the wetting

Jan 1, 1956

By Robert Roberts

(Butte Meeting, August, 1913.) IN order to obtain data on the thermal effect of the blast-furnace jacket and oil the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times.

Jan 7, 1913

By AIME AIME

WHEN H. I. Smith joined the Institute back in 1908, he was an instructor in mining and metallurgy at Penn State the college from which he had graduated the year before with a B.S. degree. He had not gone far afield for his education, for he was born, February 15, 1984 at Finleyville, Pa., a small village some fourteen miles south of Pittsburgh and without doubt famous chiefly as H. I.'s birthplace. The summer that he graduated he took a trip to the copper mines Arizona and Mexico and en route worked for four weeks for the Portland Gold Mining Co. at Cripple Creek, Colo., as a mucker and trammer. The next summer he roamed farther afield mines and metallurgical works in Europe. Wishing to see more of Arizona, he left the Penn State faculty early in 1909 and went out to Wenden in that State to become mining engineer and assistant superintendent of something called the Corona Copper Co., with 72 mining claims and a one-mule-powered whim for a hoist. When that job folded he helped build the Santa Fe railroad from Parker. Ariza., to Danby Cialif., and then came back to Pennsylvania to enter Government services as a junior mining engineer with the Bureau of Mines.

Jan 1, 1943