Search Documents

By Robert C. Berggan

The hot-milling process for reconditioning rock-drill bits is not new. It has been employed by a few mines for years and in the past decade it has been widely adopted, as its advantages have become better known. Because of the extensive commercial development in England and Canada of machines to operate on this principle, general acceptance has been largely in the British possessions and until recently has been chiefly in the field of conventional steel. In the past two years there has been a definite trend toward hot-milling of detachable bits in Canada, but only in the past year has any considerable attempt been made to build special machines for this type of work. Generally a machine designed for conventional steel has been used and special holders employed to manipulate the bit. As early as 1934 at least one operator in the United States had adapted hot-milling to conventional steel with a substantial saving in resharpening costs.1 Several other operators have taken it up but there has been no widespread adoption of the method in this country by users of conventional steel. This may be partly explained by the fact that until recently no American manufacturer produced this equipment and operators have been obliged to build their own hot-millers or import them. Several years ago a few machines were built in Seattle, Washington, and operated in some mines in the northwest, but, for reasons not generally known, the effort was abandoned. The Process Hot-milling performs the function of re-dressing the bit at a forging temperature of about 1650°F., by the removal of metal from the flutes with a milling cutter, followed by a similar cut from the bit gauge. Conventional bits are thus treated following the usual forging operation in a sharpener, and usually in the same heat.

Jan 1, 1940

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.' Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2'3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By J. E. Johnson

The brief contribution of Mr. West* furnishes a text for the present paper, which will, however, take a wider range, warranted by the writer's somewhat unusual opportunities for the study of the practice of the foundry as well as the blast-furnace, and especially of the production of satisfactory castings from iron of a composition altogether unsuitable, in the opinion of the average foundryman, for that purpose. Mr. West has observed that plates cast from direct-metal of a certain composition could be planed, whereas this would have been impracticable with cupola-metal of like composition; that furnace-metal has more " life " (i. e., fluidity, or a higher temperature) than cupola-metal; that it throws out much " kish," etc. And he suggests that blast-furnace managers may throw further light on the greater softness of direct-metal castings. Perhaps such light may be furnished to some extent by the present paper. The difference between cupola-metal and furnace- or direct-metal is, first of all, in the lower average sulphur-content of the latter. It has been proved by experiment that iron increases in its content of sulphur to a considerable extent with each remelting. More than thirty years ago Fairbairn showed that a certain iron after remelting 18 times had only five-

Jan 1, 1905

By W. H. Bassett

IN the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-min.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage. 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystallization of cold-worked alpha brass on annealing,1 Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work.

Jan 1, 1919

By Bruce W. Gonser, A. U. Seybolt

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By A. U. Seybolt, Bruce W. Gonser

A few copper-zinc-hasp alloys mppt die-casting requirements reasonably well, although improvements are desired. Aluminum bronzes, high-tin bronzes and some copper-nickel-zinc alloys can be die-cast, according to Herb,' but seldom are because of such factors as higher melting ranges and greater cost than certain of the brasses. Fox2 has summarized the copper-base die-casting alloys that were in commercial use in 1937 and has given the effects of different alloying constituents. Table 1 gives some of the properties of these alloys as reported by Fox. a Properties reported by Fox.2 b Trade name of Brastil, Doehler Die Casting Co., similar to Webert Alloy,34 American Brass Co., and Tombasil Alloy,5 Ajax Metal Co. e Trade name Tinicosil, Titan Metal Manufacturing Co. Melting point (liquidus) of the yellow brass is given by Herb1 as 1650" F., of the high-silicon Brastil (with 4.5 to 5 per cent Si) as 1600" F., and of the nickel silver as 1675" F. d Criterion not stated.

Jan 1, 1940

By Roy R. Jones, R. R. Sawyers

It has long been comnlon knowledge that workers in anthracite are prone to develop a disabling disease of the lungs. Some of the earliest scientific contributors dealing with anthracosis were: Pearson1, in his report in 1813, on the coloring matter of the bronchial glands and black spots in the lungs; Stratton2, in 1838, who first termed the condition anthracosis; Greenhow3, who reported to the pathological society in 1865, on the Black Lung of the Collier, and Pick4 in 1870, who reported on the chemical composition of the ash of a collier's lungs. Visconti5, in 1870, is accredited with being the first to use the term "silicosis" to denote the pathological condition of the lungs resulting from the inhalation of silica. Rovida6 confirmed the reports of Pick and Visconti in 1871, in his report on a case of silicosis and chemical examination of the lungs for silica content. The relationship of pulmonary infection, as associated with disabling pneumoconiosis affecting the coal miner, has frequently been discussed. While most reports have emphasized the role of infection, there has been some disagreement regarding the prevalence of tuberculosis among those suffering from anthracosis. The report by Wainwright and Nichols7 in 1905 has frequently been cited to show that the incidence of pulmonary tuberculosis among coal miners was less than that among the general population. It was their opinion that pulmonary tuberculosis was more prevalent among the miners' families than among the miners themselves. Collis and Gil-christ, in 1928 in their study of the Effects of Dust upon Coal Trimmers, concluded that among such workers there was an excess of deaths from bronchitis and pneumonia but not from pulmonary tuberculosis. They

Jan 1, 1936

By Roy R. Jones, R. R. Sawyers

It has long been comnlon knowledge that workers in anthracite are prone to develop a disabling disease of the lungs. Some of the earliest scientific contributors dealing with anthracosis were: Pearson1, in his report in 1813, on the coloring matter of the bronchial glands and black spots in the lungs; Stratton2, in 1838, who first termed the condition anthracosis; Greenhow3, who reported to the pathological society in 1865, on the Black Lung of the Collier, and Pick4 in 1870, who reported on the chemical composition of the ash of a collier's lungs. Visconti5, in 1870, is accredited with being the first to use the term "silicosis" to denote the pathological condition of the lungs resulting from the inhalation of silica. Rovida6 confirmed the reports of Pick and Visconti in 1871, in his report on a case of silicosis and chemical examination of the lungs for silica content. The relationship of pulmonary infection, as associated with disabling pneumoconiosis affecting the coal miner, has frequently been discussed. While most reports have emphasized the role of infection, there has been some disagreement regarding the prevalence of tuberculosis among those suffering from anthracosis. The report by Wainwright and Nichols7 in 1905 has frequently been cited to show that the incidence of pulmonary tuberculosis among coal miners was less than that among the general population. It was their opinion that pulmonary tuberculosis was more prevalent among the miners' families than among the miners themselves. Collis and Gil-christ, in 1928 in their study of the Effects of Dust upon Coal Trimmers, concluded that among such workers there was an excess of deaths from bronchitis and pneumonia but not from pulmonary tuberculosis. They

Jan 1, 1936

By R. R. Sayers

IT has long been common knowledge that workers in anthracite are prone to develop a disabling disease of the lungs. Some of the earliest scientific contributors dealing with anthracosis were: Pearson1, in his report in 1813, on the coloring matter of the bronchial glands and black spots in the lungs; Stratton2, in 1838, who first termed the condition anthracosis; Greenhow3, who reported to the pathological society in 1865, on the Black Lung of the Collier, and Pick4 in 1870, who reported on the chemical composition of the ash of a collier's lungs. Visconti5, in 1870, is accredited with being the first to use the term "silicosis" to denote the pathological condition of the lungs resulting from the inhalation of silica. Rovida6 confirmed the reports of Pick and Visconti in 1871, in his report on a case of silicosis and chemical examination of the lungs for silica content. The relationship of pulmonary infection, as associated with disabling pneumoconiosis affecting the coal miner, has frequently been discussed. While most reports have emphasized the role of infection, there has been some disagreement regarding the prevalence of tuberculosis among those suffering from anthracosis. The report by Wainwright and Nichols7 in 1905 has frequently been cited to show that the incidence of pulmonary tuberculosis among coal miners was -less than that among the general population. It was their opinion that pulmonary tuberculosis was more prevalent among the miners' families than among the miners themselves.. Collis and Gil-christ8, in 1928 in their study of the Effects of Dust upon Coal Trimmers, concluded that among such workers there was an excess of deaths from bronchitis and pneumonia but not from pulmonary tuberculosis. They

Jan 1, 1935

By C. A. Siebert, S. H. Bush

Isothermal temper-embrittlement studies were conducted on a 5140 steel at various temperatures for times as long as 3000 hr. Specimens from the embrittled steel were subjected to impact tests, metallographic examination, microhardness, and lattice-parameter measurements. SEVERAL of the steels in the low alloy group are subject to a pronounced decrease in impact energy if held within, or cooled slowly through, a range of temperatures below the lower critical. This phenomenon, known as temper embrittlement, is quite pronounced in the chromium steels of which AISI 5140 is typical. This study considered the response of one heat of 5140 steel when embrittled isothermally at various temperatures for times as long as 3000 hr. Excellent reviews of the work done in the field of temper embrittlement have been written by Hollomonl and Woodfine.' Both authors list the various theories which have been advanced to explain temper embrittlement. Some of the mechanisms considered were: 1—a transformation below 700°C; 2—an allotropic modification of iron; 3—precipitation from the ferrite of such compounds as carbides, nitrides, phosphides, or chromium oxides; 4—decomposition of retained austenite; 5—modification of special carbides; 6—grain-boundary segregation; and 7—selective distribution of carbides. The present study investigated the changes in hardness, Meyer's number, impact properties, micro-structure, and lattice parameter which occurred on embrittlement. Previous studies considered the influence of microstructure and of prior austenitic grain size3 on the response of 5140 steel to temper embrittlement. Equipment and Procedure All samples were taken from one heat of 5140 steel; the chemical composition of this steel was: 0.43 pct C, 0.86 pct Mn, 0.020 pct P, 0.019 pct S, 0.27 pct Si, 0.84 pct Cr, 0.10 pct Ni, 0.06 pct Mo, 0.10 pct Cu, and the remainder Fe. The material was received as % in. rounds. This stock was cut down to blanks measuring approximately 0.425~0.425~2.196 in. Heat Treatment: The rough blanks were normalized at 1600°F (870°C) for 1 hr, then austenitized at 1600°F (870°C) for 1 1/2 hr, and quenched into an agitated oil bath. The specimens were tempered at 1275°F (690°C) for 5 hr and water quenched. These tempered specimens were designated as the toughened state. Embrittling Treatments: The tempered bars were divided into sets and subjected to the various embrittling treatments listed in Table I. Temperatures from 750" to 1050°F were investigated for times of 1 to 3000 hr. Special tests to determine the effect of heating a short time at a higher temperature after long-time embrittlement at some lower temperature were also conducted. All specimens were water quenched at the end of the embrittling cycle, then ground and notched to obtain standard Charpy V-notch specimens. Impact Tests: The bars were fractured in a 260 ft-lb Charpy impact unit; specimens were fractured at temperatures ranging from —315°F to room temperature. Fixed temperatures used consisted of —315°F with liquid nitrogen, —115°F with dry ice and acetone, and 32°F with ice and water. Intermediate temperatures were obtained by suspending the bars in a jig over the liquid nitrogen, dry ice and acetone, or ice and water.

Jan 1, 1955

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time. '

Jan 5, 1916

A group of prominent engineers and contractors of Chicago and vicinity have cooperated in forming a Joint Committee on Military Engineering. The founders are members of all of the leading engineering and contracting organizations of Chicago, including the local branches of the national engineering societies. The purposes of the Committee are to further military preparedness among engineers, contractors and their associates by the following means: (1) Courses of lectures; (2) assigned reading; (3) studies and practical instruction in military engineering;. (4) assisting engineers to qualify as officers in the National Reserve Corps of Civilian Engineers; (5) urging enlistment in and support for engineer troops of the National Guard and such other organizations as the Government may create; (6) furthering instruction in military engineering in training camps and the attendance in them of those qualified; (7) by such other means as from time to time may be deemed advisable. The Joint Committee has already prepared a program covering the vital points outlined. To date the program is practically complete for a period extending from April 20 to July 25. Something of interest will be taken up each week, including lectures by Lieutenant-Colonel W. B. Judson, Engineer Corps, U. S. Army; two lectures by Major P. S. Bond, Engineer Corps, U. S. Army; Lieutenant-Colonel Mason M. Patrick, Engineer Corps, U. S. Army, and several exhibition drills, terrain exercises and inspection trips under the direction and guidance of various officers of the Engineer Troops of the Illinois National Guard. Additions to the program will be made from time to time.

Jan 5, 1916

By W. L. Maxson

GRINDING is one of the major problems in present-day milling practice, and in many cases, it represents one of the main items of expense. It becomes necessary from time to time, to compare grinding practice in one plant with that in another plant, and in making such comparisons, it would be very desirable were there available accepted standards of grinding resistance for the materials involved. Such a set of grinding constants would also be of considerable value in planning new grind-ing installations. There have been some tests published, notably those of Lennox,1 which have been generally cited as a basis for such comparisons. Most of the tests made have been based upon open-circuit grinding, in which a weighed sample of the ore was crushed to pass a certain mesh, and was .then ground under certain conditions, either wet or dry. Grinding was continued until a certain desired fineness was attained, and the compari-sons based on the grinding time, or the samples were all ground for a certain specified length of time and comparison based upon the screen analysis of the products. Such methods have been acceptable where the ore was to be ground in open circuit. However, in modern milling practice, many grinding problems involve closed circuits wherein the oversize returns to the mill and a large circulating, load builds up. A method of testing that does not take the circulating load into consideration might yield results quite different from those to he expected in practice, because the minerals in the ore that offer maximum resistance to grinding will accumulate in the circulating load up to an equilibrium value. Thus the nature of the ore charge in the mill at any instant may differ greatly from that of the new feed, with a consequent error in the rate of grinding determined by such a method.

Jan 1, 1933

By Hassell E. Hunter

The Wyoming Minerals - Conoco Crownpoint Joint Venture represents the first time that big hole drilling has been exclusively used to develop a privately financed mine. Three shafts, one ten feet in diameter and two six feet in diameter, have been successfully drilled to depths of 2243', 2188' and 2188' respectively and lined with hydrostatic designed steel casing. The largest shaft is to be used to as a development shaft to handle muck and water from enlargement and station excavation of the other two shafts. A reverse fluid air assist circulation system with potassium base mud was used during drilling. The mud was cleaned by settling in steel lined tanks with assistance from cyclone type sand separators. Deviation was monitored with wireline gyroscopic surveying instruments at 30 foot intervals. Horizontal departure did not exceed 16 inches off perpendicular. Casing was designed to withstand full hydrostatic pressures with a 1.5 safety factor for the large shaft and 1.25 safety factor for the two smaller shafts. All casing welds were x-rayed prior to lowering the casing into the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1982

By K. E. Starling

Phase equilibria data were used to develop an equation-of-state correlation for complex hydrocarbon mixtures, thereby circumventing difficulties associated with use of pressure-volume-temperature data. Equilibrium phase data for two condensate reservoir fluids were used to determine equation-of-state parameters for hydrocarbons as heavy as C22H46 in a modified form of the Benedict-Webb-Rubin equation of state. Comparative tests of K-values from the resultant correlation were made with data for condensate reservoir, separator and gas plant absorber mixtures. Generally, for temperatures above OF and computed liquid densities below 0.55 Ib-mole/cu ft, the modified BIVR equation predicted K-values in close agreement with the experimental data. INTRODUCTION Accurate predictions of thermodynamic behavior for complex hydrocarbon mixtures are necessary for many calculations in the petroleum industry. Because of the relatively high cost of extensive experimental data, many correlations for prediction of phase behavior have been developed. Some of these, such as the correlation of K-values presented in the NGAA Equilibrium Ratio Data Book, are totally empirical.l Others, such as the Benedict-Webb-Rubin (BWR) equation-of-state method, are semitheoretical.2-4 Unfortunately, published correlation methods often do not accurately predict the phase behavior of complex hydrocarbon mixtures, principally because of inadequate representation of the effects of components heavier than decane. This paper presents a new approach to this problem in which basic equation-of-state relations including heavy hydrocarbon effects are applied. Equilibrium phase data for two condensate reservoir fluids containing hydrocarbons as heavy as C22H46 are used to correlate component K-values. The BWR equation was chosen as the prototype equation of state for this study because of its proven capability for accurately predicting phase behavior and thermodynamic properties of light - hydrocarbon mixtures? Research was directed toward development of BWR parameters for the heavy hydrocarbons and modifications of the mathematical form of the BWR equation for application to complex hydrocarbon mixtures. The new equation-of-state approach presented differs considerably from previous methods in that phase equilibria rather than PVT data are used for determination of equation-of-state parameters. It is an explicit approach since the parameters are determined directly from mixture data. As such, it does not encounter problems inherent in the implicit method used by Benedict, Webb and Rubin 2-4 and numerous other investigators—one in which mixture parameters were postulated to be functions of the pure component parameters. The pure component BWR parameters, in turn, were determined from experimental PVT data. This method has been limited to mixtures containing components lighter than decane because of lack of vapor phase PVT data. Studies have been reported in which BWR parameters have been determined explicitly from PVT data for binary mixtures.6-8 However, since small concentrations of heavier components have only a minor effect on PVT behavior, it is doubtful that these explicit methods would yield useful results for condensate systems. Ellington and Eakin9 have shown that the accuracy of K-values predicted by an equation of state developed from mixture PVT data probably would be more than an order of magnitude lower than the accuracy of the PVT data. On the other hand, an equation of state utilizing parameters developed from phase equilibria data should predict K-values with accuracy comparable to the accuracy of the experimental phase compositions. This work applies this explicit approach with the objective of improving hydrocarbon mixture phase behavior predictions. Results are evaluated by comparing predicted and experimental K-values at reservoir, separator and gas plant

Jan 1, 1967

Among the bills now pending in Congress is one to authorize exploration for and disposition of coal, phosphate, sodium, oil, oil shale, and gas on, public domain. One, to provide protection and government revenue for potash and for zinc ores and products. One to prevent withdrawal of mineral lands from entry and occupancy by law, also to promote, production of quicksilver, tungsten, sulfate, pyrites, and sulfur, and of manganese and manganiferous ores. Three resolutions have been introduced to suspend requirements of annual assessment work on mining claims during year 1919 and one to relieve owners of mining claims mustered into military service.

Jan 8, 1919

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleysl and Gathmann,2 who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1951

IT is difficult to judge how much influence the success attained during its first year, 186465, by the School of Mines at Columbia had on developments in education for the mineral industry elsewhere in the immediately subsequent years. The facts are as follows: 1. The Massachusetts Institute of Technology began giving instruction in February 1865, with a mining course included in its curriculum. 2. Early in 1865 the faculty of the Department of Science, Literature and the Arts of the University of Michigan requested permission from the Regents to establish "a course of study to be called the School of Mines . . . Also that the degree of Mining Engineering be conferred on students who should complete the course of study prescribed in the same." A resolution authorizing this was adopted by the Regents on March 28, 1865. 3. Samuel Hooper endowed a Sturgis-Hooper professorship of geology at Harvard in 1865 with the intention of making it a nucleus of a new School of Practical Mining and Geology. 4. Yale appointed Alfred P. Rockwell professor of mining in 1865. 5. Lafayette College appointed Henry S. Osborn professor of mining and metallurgy in 1865. 6. Washington College (as Washington and Lee was then known), rising out of the ashes of Civil War destruction, made a fresh start in 1865, with General Lee as its president, and offered a mining course in the first catalogue thereafter published. 7. Lehigh University, founded in 1866, had a mining curriculum from its beginning. 8. Rensselaer Polytechnic began offering a curriculum in mining and metallurgical engineering in 1867. It would be natural to suppose that these events were a reaction to the success of the school at Columbia, and possibly they

Jan 1, 1941

IN the early period of steelmaking, ingot structure and segregation were of no practical importance. Crucible melting required very small ingots that gave little segregation, and a small inserted hot top prevented pipe. As larger ingots were poured from bessemer converters and open-hearth furnaces, segrega- [ ] tion, piping, and gas evolution became increasingly important. The techniques of making semikilled and rimmed ingots were developed with little knowledge of the actual mechanism of the process. The first studies of solidification were made by the Brearleys1 and Gathmann,2- who used stearine to show the effects of shrinkage and mold shape. Fig 11-1 is a picture of a series of stearine ingots at various stages of solidification. These studies showed that the liquid solidifies at a nearly uniform rate from the sides and bottom of the mold and demonstrated the formation of

Jan 1, 1964

By P. A. Toynbee

An experimental air-slide classifier1 has been applied to the de-dusting of ground dolomite in an attempt to produce a grade of -30 +150 mesh (B. S. Sieves) material from a raw material containing 30-35% of the -150 mesh fraction. Air flows varying between 1.5 and 2.5 cu ft/sec sq ft of screen area were used. The throughput of dolomite was between 80 and 100 lbs/h. inch of screen width. The size analyses of the de-dusted material and of the original dolomite are shown in table at right. The proportions of the +100 mesh material in the feed and in the de-dusted products have been used to calculate materials balances, on the assumption that there is no loss, as dust, of this +100 mesh fraction. By interpolation, it can be shown that a de-dusted product recovery of 68.5% will be obtained at an air flow of 2.13 cu ft/sec sq ft of screen area. The feed material contains 68.5% of +150 mesh material, so that if the de-dusting gave a perfectly sharp cut, the product would contain no material less than 150 mesh. Further calculations based on the size analyses, show that, at an air flow of 2.13 cu ft/sec sq ft of screen air, the -150 mesh fraction in the de-dusted product will fall just below the specified maximum limit of 5%.

Jan 1, 1964