Search Documents

By Robert Warner

WHEN a new mine is opened, and often when an operating mine must adapt itself to physical or economic changes, a mining system must be selected in complete detail. In the past the plan chosen was usually the product of the local staff alone, however limited the training and experi-ence of that staff might be, which often resulted in the introduction of methods that were familiar to the staff, but not so well suited to the con-ditions as others unknown to the local men. A new management, noting the difficulties with the existing layout, might make modifications or complete changes, so that many mines in their history have seen a whole series of mining systems, each somewhat laboriously grafted on to its predecessor. This should not be interpreted as a condemnation of the older staffs for sticking to the tried systems, such as open square-sets in the early days at the Homestake, because they knew it would work after a fashion, nor does the statement apply to the technically trained, and usually broadly experienced staffs of most present-day properties. The older miners did not have the variety of tools and methods, nor the present freedom of transfer of information as to what the other man is doing, and so did the best they could under the circumstances. Finally, the higher grade of the ores made the choice less vital. The ever-increasing need to mine low-grade orebodies, with a fixed or even lower price for the metal produced, has caused an increasing need for low-cost mining. In most new mines this has simplified the problem of selection by eliminating from consideration all of the high-cost systems, but it has also complicated the choice by the necessity for refinement in detail and a close adjustment of the plan selected to all the conditions at the property. In these low-cost problems any textbook division of mining systems as applied to "beds, veins or masses" avails little as a guide. It should be realized at the outset that to' be successful under modern competitive conditions a system of mining must be worked out with elaborate detail, with careful time scheduling and control of the various elemental operations, and that after it is introduced it must be run with a large amount of technical direction.

Jan 1, 1933

By H. Hubert

The first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lurmann and to Lencauchez, who had pointed out the blast-furnace as a powerful gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgom Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Jan 1, 1907

By H. H. Stoek

MINE models have three distinct uses: 1. As exhibits in expositions and museums. 2. As exhibits in law suits. 3. As illustrations in teaching mining engineering. All three uses are in a sense educational. The third, or distinctively teaching function, has not been extensively developed in America as it has been abroad, chiefly because of the cost of the models and the scarcity of model makers. In connection with expositions, such as the Columbian, the Louisiana Purchase, and the Panama-Pacific, a number of very good mine and metallurgical models were prepared with funds furnished by State commissions, by mining organizations or mining companies. At the close of these, expositions, some of these models have been deposited in National or State museums or in educational institutions, but too many of them have been lost, or have been stored, away in some mining company's office or in the basement of some State building, where they have been lost sight of and have gradually fallen to pieces. A visitor to a German mining school is impressed by two facts: 1. The mining laboratories are in general inferior to those in America. 2. The mining museums are infinitely superior -to ours, particularly in models exhibited. One may reply to this comparison by saying that a museum is necessarily a work of time. From the historical standpoint this is, of course, true, but it is not necessarily true in connection with a working museum intended to illustrate current practice. For instance, the oldest mining school in Germany, that at Freiberg, has much excellent historical material, but very little on modern practice, while Berlin, one of the youngest German mining schools, has a most extensive and valuable collection of modern appliances and models. This is true in spite of the fact that one of the best-known model shops is at Freiberg, from which many of, the models to be seen in America have come. Because many of the models in American mining schools have come from

Jan 4, 1917

Nominating Committee.-On the recommendation of the President, the Board of Directors, at their meeting on Apr. 25,1913, appointed the following Nominating, Committee to nominate officers and directors for next year: John Hays Hammond (Ex-President), Chairman. Robert H. Richards Chairman of Boston Local Section. Richard S. McCaffery, . . . . Chairman of Spokane Local Section. Chester F. Lee Chairman of Puget Sound Local Section. Frederick G. Cottrell, . . . . San Francisco, Cal. Charles W. Goodale Butte, Mont. James W. Maleolmson, . . . . Kansas City, Mo.

Jan 5, 1913

By ELTCENE A. WHITE

WE are all interested in our ou7n lines of endeavor and consider ourselves the center of the universe. The farmer thinks he is the most important man because he feeds us. The doctor knows he is the real center because he keeps us well. The lawyer says that he is indispensable because he keeps the peace. The banker furnishes us a place to keep our money and tells us how to make proper use of it. The miner sags that without metals there would be no civilization. I think that my branch has sufficient interest and exhilaration. of accomplishment to fully occupy any man's mind and attention. Mining and metallurgy are as old as the human race. It did not have much, if any, importance in the stone age as there are not found remains of iron and copper, but in the bronze age, which was co-existent with the stone age, it came to the front. Iron and copper were the most important metals. Copper, as bronze, was known in ancient Egypt, I\~:IS important in Rome and other parts of Europe and in Asia; in South America among the Aztecs and farther North were the Mound Builders and the early inhabitants of Lake Superior. At a very early date the Egyptians conquered the Sinai peninsula for the sake of the copper produced there. The history of copper metallurgy can be compared to that of a flower. The seed is sown in darkness and in the Dark Ages the crude metallurgy of copper began. As the shoot comes up from the seed it may be compared to the age of alchemy; the branches of the plant can be compared to the Middle Ages; the flowering shoots to the 17th century, the budding to the 19th and the blossom to our own time from 1870 on.

Jan 1, 1930

By N. W. Lord

Having recently had occasion to make a series of analyses of fire-clays for the present Ohio Geological Survey, I found that the amounts of potash and soda determined indirectly by measuring the chlorides volumetrically did not " check " with those obtained directly. Investigation with the spectroscope showed the presence of lithia in what seemed very appreciable quantities. The examination was made of a considerable number of samples, and in every case this element was found, though in varying amounts, as judged by the intensity of the spectrum. To guard against error from the impurity of reagents, the whole process was repeated, using the same reagents in corresponding amounts, but leaving ont the clay. In no case did these " blanks" show lithia; hence the presence of this element in the clays seemed to be established conclusively. In the same series of analyses, titanic acid, in amounts varying from three-tenths to nearly two per cent., was found. The presence of titanium was first observed in the Ohio clays, nearly three years ago, in the examination of clays from Logan. The occurrence of this element is, of course, not unusual in clay, but I believe that none of the published analyses of Ohio clays give it; certainly none of the former Ohio geological reports speak of its presence. The following analyses show both the above ingredients. They were made during the summer of 1883.

Jan 1, 1884

By A. J. Mcintosh

PRICE changes in competing fuels in the last three decades have reflected the changes in the consuming habits of the people of the United States. Prior to World War 11 the importance of fuel oil and fuel gas increased almost constantly while the relative importance of both bituminous and anthracite coal decreased. During this same prewar period coal prices increased to a much greater extent than oil prices. In fact, in many years, oil prices declined and in most cases are now no higher than they were back in 1925-26. During the war natural economic trends were entirely upset because of the tremendous petroleum requirements of the Army and Navy. Under these conditions many industrial plants were converted to the use of coal and the new installations in home heating and industrial plants of all kinds which might have used oil were practically eliminated. Although petroleum prices were rigidly controlled by OPA coal prices increased several times during the war. An over-all statement as to the rela-

Jan 1, 1947

H. RIES, Ithaca, N. Y.-The part of Mr. Fiske's paper that interests me especially is that portion dealing with the raw materials, and the tests that were applied to the raw materials in order to determine their value in advance, if possible, because that, I believe, is a step in the right direction. For a number of years I have done my best to persuade different consumers of clay to develop standard methods for testing raw materials. We have in this country a large variety of clays which can be used for a great many different purposes, but in many cases the consumers either have no standard methods for determining the value of those clays in. advance, or if they have they do not publish them; consequently it often puts the clay miner at a disadvantage. If, for example, manufacturers of different types of refractory materials would state publicly just what physical tests their raw materials have to meet, it would, I believe, help them to find more easily the materials that they are looking for, and the clay producer would also be benefited. It would also encourage him to have his clays tested in advance, so that samples could be accompanied by certificates of physical tests that would be of convenience to the manufacturer. At the present time, in this country there are certain types of clay which seem to be rather scarce. There apparently are not many deposits of clay that are exactly suited for the manufacture of zinc refractories. So, too, there are not many deposits of clay that are suited for the manufacture of glass-pots, or the blocks for glass tank furnaces, or clays that can be used for graphite crucibles. Now, in many cases, no standard series of tests has been developed. I am also gratified to see that Mr. Fiske considers the tensile strength. tests of value. Some years ago the American Ceramic Society appointed a committee to draw up a series of recommendations covering standard tests. These recommendations were especially for the use of State geologists and the U., .S. Geological, Survey. Among the tests that were considered was the tensile-strength test, which Mr. Fiske has mentioned in his paper. Unfortunately, a majority of the committee turned it down, and the test was therefore not officially approved, but two of us, who formed the minority, believed in it. Since then the other members of the Committee have come to see that that is an important test to make and Mr. Fiske has emphasized it in his paper.

Jan 1, 1918

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By Sadao Maruyama

INTRODUCTION Since the big discovery of Kuroko deposits in Kosaka mine, Akita Pref., northeastern Japan in 1959, major Japanese mining companies have been engaged in extensive exploration for the deposits expending large amounts of money. Above all their exploration activities have been particularly fruitful in discovering new deposits in northern Akita Pref. It is estimated that the total ore reserves newly found in the area are at least 50 million tons. Kuroko deposits are the most important ore source of copper, lead and zinc in Japan and have been mined since last century in the said area. Kuroko (black ore) is fine, compact aggregates with sphalerite , glena and barite as principal constituents and chalco- pyrite, pyrite and tetrahedrite as subsequent constituents. The name Kuroko comes from its appearance. It is not rare that total grade of copper, lead and zinc reaches 20 - 30% and the gold and silver content is also fairly good. Accordingly the unit value of the ore is much higher than the ore from other types of deposits. Besides the Kuroko ore, the Kuroko deposits consists of Ohko (yellow ore, massive cupriferous pyritic ore), Keikoh (silicious ore, cupriferous network ore) and gypsum ore. This type of deposit is considered to be not only an important source of base metal but also a source of gypsum and barite. Although the importance of this type of deposit had been commonly recognized, sub-surface nature of the occurrence hampered exploration work. In recent years the improved exploration techniques and increased knowledge of the Kuroko deposits have met with remarkable success in the location of new deposits. This outburst of exploration and dis-

Jan 1, 1970

By Chester O. Ensign

Many publications to date have advocated under- seas mining operations, optimistically overlooking the paucity of information on mineral distribution and the ocean environments in which minerals occur. Such articles (smattered with opinion, as is this article) are herein tempered by my more conservative views on the economics of mining under the seas. For purposes of this paper, underseas mining refers only to the deeper surficial deposits of the continental shelf and the deep sea floor, i.e., the deposits of phosphorite and manganese nodules.

Jan 9, 1966

By V. H. Wilhelm

During the first half of the year 1935, the oil industry in California was on a fairly profitable basis, owing mainly to the operation of the Petroleum Marketing Agency. Coincident with the discontinuance of enforced curtailment, California production surged upward from an average of about 500,000 bbl. per day (over the first five-month period) to approximately 625,000 bbl. per day (over the last seven-month period). On Dec. 9 the state production had reached a peak of over 700,000 bbl., a figure that had not been approximated since the early days of voluntary curtailment (Fig. 1). A price cut was instituted during the last half of August, but had no deterring effect on operators that were determined to take advantage of the breakdown of curtailment and produce to capacity. New reserve figures, compiled from actual potentials, available after cessation of curtailment, revealed the startling fact that California reserves were rapidly declining. This situation, coupled with the desire among operators to obtain a more equitable price for their dwindling reserves, caused a restoration in November of a portion of the August price slash. A further rise in price was effected in early December, and crude quotations at the end of the year closely approximated those in effect during the first right months. At the close of the year, the industry felt confident that the production situation was under control. In all fields where competition is keen because of close spacing, production is gradually declining. In the Los Angeles Basin especially there is no likelihood of a large amount of overproduction, unless a new pool is discovered or deeper drilling reveals a prolific source of crude. As long as the fields that are operated by a few companies, such as Kettleman Hills, North Belridge, Ventura Avenue, West Coyote, Dominguez, and some others, can be controlled, it is believed that the overproduction problem in California will be solved.

Jan 1, 1936

By V. H. Wilhelm

During the first half of the year 1935, the oil industry in California was on a fairly profitable basis, owing mainly to the operation of the Petroleum Marketing Agency. Coincident with the discontinuance of enforced curtailment, California production surged upward from an average of about 500,000 bbl. per day (over the first five-month period) to approximately 625,000 bbl. per day (over the last seven-month period). On Dec. 9 the state production had reached a peak of over 700,000 bbl., a figure that had not been approximated since the early days of voluntary curtailment (Fig. 1). A price cut was instituted during the last half of August, but had no deterring effect on operators that were determined to take advantage of the breakdown of curtailment and produce to capacity. New reserve figures, compiled from actual potentials, available after cessation of curtailment, revealed the startling fact that California reserves were rapidly declining. This situation, coupled with the desire among operators to obtain a more equitable price for their dwindling reserves, caused a restoration in November of a portion of the August price slash. A further rise in price was effected in early December, and crude quotations at the end of the year closely approximated those in effect during the first right months. At the close of the year, the industry felt confident that the production situation was under control. In all fields where competition is keen because of close spacing, production is gradually declining. In the Los Angeles Basin especially there is no likelihood of a large amount of overproduction, unless a new pool is discovered or deeper drilling reveals a prolific source of crude. As long as the fields that are operated by a few companies, such as Kettleman Hills, North Belridge, Ventura Avenue, West Coyote, Dominguez, and some others, can be controlled, it is believed that the overproduction problem in California will be solved.

Jan 1, 1936

By F. C. Smyers, E. W. Merrick

ALTHOUGH the zinc and pyrite concentrates produced at Midvale go to other companies, the United States Smelting Refining and Mining Company smelts and refines its own lead. Refining is the first step of the process that is done at some distance from the mining operations, the plant being at East Chicago, Ind., an industrial center about 25 miles southeast of Chicago. For years it has been notable as being the only lead refinery in the country using the Betts electrolytic process. The original buildings, many of which are still in use, were erected in 1906 when the plant was known as the United States Metals Refining Co. In 1920 the parent company sold its copper refinery at Chrome, N. J., and since the copper refinery was also known as the U. S.

Jan 1, 1948

By R. D. Springer, R. L. Wilcox, P. A. PALMARTAN, R. K. Waring, E. A. Anderson

A knowledge of the mutual liquid solubility of zinc and lead is of importance in various phases of zinc metallurgy. The determination of this solubility has been the subject of numerous investigations, but unfortunately the results vary widely, particularly at higher temperatures, and it has been impossible to decide what data are most reliable. It was decided to investigate the matter and in view of the disagreement in the published results, it was felt necessary to take rather unusual precautions to insure the reliability of the data. For this reason determinations were made by four different methods, and the procedures of several of the previous investigators were duplicated. The previously used methods can be divided into two classes: methods involving freezing the entire melt and taking samples of the lead-rich and zine-rich phases in the solid state,l,2 and methods in which the samples are taken while the bath is liquid and at the desired temperature.3,4 Data obtained by methods involving freezing the entire melt show much lower solubility of lead in zinc than methods in which the liquid is sampled at temperature. The latter method was used by Spring and Romanoff5 and by Hass and Jellinek.6 The results of these two investigations are in agreement at temperatures near the melting point but at higher temperatures Hass and Jellinek find a higher mutual solubility. The low-temperature section of the zinc-lead equilibrium diagram is given by Peirce and Anderson.7 The diagram is based on the data of Hodge and Heyer,8 Arnemann,9 and Peirce.10

Jan 1, 1934

By HENRY JULLUM

THE ARGONAUT' mill stands at the crest and spreads down the western slope' of a hill, which incidentally covers the' outcrop of the Argonaut vein' at this point. The collar of the main shaft of the mine is situated on the eastern slope of the same hill 120 ft. below the highest ?point. The present mill, built in 1916, was designed to treat 250 tons per 24-hr. day. This capacity has not been attained recently owing to the inability of the mine to produce enough ore while extensive development and underground construction were under way. At present, however, the mine is more than able to take care of the mill requirements.

Jan 1, 1932

By NILS DANIELSEN

THE name of Swedish charcoal iron will probably bring to the memory of many old consumers an extremely tough and ductile iron which was formerly used in considerable quantities for common blacksmith purposes. To-day very little of this iron goes to such kind of work. Swedish charcoal iron is merely a speciality which is chosen whenever its remark¬able properties can be utilized. By giving a rough sketch of the manufacturing process of Swedish charcoal iron, the character of the iron, its weak as well as its strong points will more easily be understood. Swedish charcoal iron is a wrought iron also known in the United States under the name of Norway iron and Swedish Lancashire iron. The name Norway iron seems to have been attached to the product for the reason that in the earlier days it was generally brought into the States by Norwegian ships. However no iron of this kind is now made in Norway. The reason for the name Swedish Lancashire iron is that the manufac¬turing process emanated from Lancashier in England, the method being generally adopted in Sweden in the years 1831-1850. Today this iron is, with the exception of one plant in the United States, made in no place in the world outside of Sweden.

Jan 1, 1924

By Fred Prime

To an association like the one before which I read this paper, few questions can be more important and constantly recurring than the following, viz.: "What economy can be effected in the manufacture of American iron ?" And it is the one with which I purpose to deal in this paper; premising, however, that my object is merely to indicate the direction in which an answer should be sought for, rather than to give it myself. This subject may be divided into two parts; " Economy in the production of pig-iron," and " Economy in the manufacture of wrought-iron;" but it is to the former alone that I shall confine myself this evening.

Jan 1, 1873

By GEORGE D. RAMSAY

WHEN the Ironton blast furnace of the Columbia Steel , Co. was first put into operation the iron ore was mined frol11 the deposit near Iron Springs, Utah. This is principally a hematite with 12 to 20 per cent of magnetite finely disseminated throughout the ore. It varies from a fairly soft broken rock structure to that which is hard and compact. In the broken form it will weigh about 150 lb. per cu. ft., and in place the density is approximately 250 lb. per cu. ft. The first ore received for the blast furnace was crushed so as to pass through approximately a 4-in. square opening screen. A typical screen test of this ore is shown in Table 1.

Jan 1, 1935

By John J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely in- adequate in certain other areas, but there are important sections where this system is clearly applicable.

Jan 7, 1959