Search Documents

By Franklin H. Sharp, Kenneth L. Clifford

During the last few years the New Lead Belt of Southeastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, MG. for about 35 miles. The ore occurs as replacement deposits in the Bonneterre lime- stone formation which is about 1000 ft below the surface. In most of the mines, enough water is produced to supply the milling requirements without any reuse. There are dry areas, however, and at least two mills must rely on water reclaimed from their tailings lake to augment the mine water. These mills have no choice but to utilize recycled mill water.

Jan 7, 1973

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

By J. B. Caine

THE investigation outlined in this paper was carried on at the plant of the Sawbrook Steel Castings Co., Lockland, Ohio. EFFECT OF TEMPERATURE In the study of the effect of temperature, heats were made with the Sawbrook company's standard practice, using multiple slags, the only difference' being that the heats were tapped at two temperatures; one group between 2960° and 3040°F and the other group between 3200° and 3250°F. Slags were weighed throughout the heat at each slag change and after the heat was poured. Only the significant slag weights, those of the total slag and the finishing slag, have been reported.

Jan 1, 1947

By Frederick Laist

F. N. FLYNN, Clifton, Ariz.-I would like to ask Mr. Mathewson what percentage of his leaching liquor is wasted at this time? It has a bearing on the question in connection with the New Cornelia, and I think it is a very important question. E. P. MATHEWSON, Anaconda, Mont.-I am not sure what the percentage is now, but we don't discard the strong liquors. Something like 25 per cent. of the wash water taken out each day is sent over a special set of scrap iron tanks, and the copper recovered there. We had a little trouble at first. We did not proceed to use the sponge iron for the reason that the plant we originally contemplated was abandoned for flotation. Our original idea was to use a leaching process on all the tailings of the mill, but we found it would take a great deal of time to build a plant; and the cost of operating the plant we estimated to be about the same and the recovery the same. It was a question of time with us, and we decided to adopt flotation. That changed our plans. We now have the leaching plant, treating the tailings of the old dump, and the flotation applied to the current tailings. The sponge iron was figured for the large plant. We can get all the scrap iron necessary for the small plant-plenty from the scrap produced in the main plant of the smelter.

Jan 12, 1916

By W. E. Wrather

DURING the war the mineral industry, and metal mining in particular, extended itself more than any other to attain the limit of its productive capacity. Likewise, probably no other industry went quite so far toward jeop¬ardizing its own economic future through depletion of material reserves. Once we looked to Europe for most of the manufactured goods we needed. Our own limited mineral requirements were easily supplied from mines near the Eastern seaboard. With expansion and industrialization, our mineral needs increased in proportion, and the centers of mining activity moved westward to Michigan, Wisconsin, Minnesota, and the Tri-State district, where seemingly inexhaustible high-grade deposits of iron, copper, lead, and zinc ores were opened and rapidly developed.

Jan 1, 1946

By E. W. Engle

Fox several years the Fansteel Products Co. has been engaged in the production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770° C., tungsten 3350° C., and molybdenum 2550° C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum some¬what resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids.

Jan 3, 1925

By L. W. Blau

THE entrance of geophysics and geochemistry into petroleum engineering may be viewed with apprehension by some engineers. They may not remember the time when "practical oil men" opposed the invasion of engineers into the field of petroleum production. By their excellent contributions they established themselves. In the popular mind, engis veers are practical men whereas physicists and chemists are suspected of being theoretical. It will be best to annihilate this misconception right now at the beginning of a closer relationship between petroleum engineers. geophysicists, and geochemists.

Jan 1, 1943

By Hans Lundberq

IINDUSTRY'S attention is now focused on the production of munitions thereby creating a demand for certain minerals which in prewar days were produced only in limited quantities. Now production of these minerals must he increased from the known deposits and new deposits must be found. Can geophysics help? "War minerals" such as tin, vanadium, tungsten, antimony, manganese, chromium, and cinnabar have no physical characteristics sufficiently different front the country rook to permit their direct location by ordinary geophysical methods. As already demonstrated in work on gold and oil, useful information may be obtained indirectly, however, outlining structural features or geological conditions favorable for the deposition of such ores or the accumulation of oil. Recently, more direct and truly qualitative methods have been brought into a useful and practical stage, and by the combined application of old and new methods a technique has been developed which, it is hoped, will be of importance in the search for these vital minerals.

Jan 1, 1941

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970

By Charles F. King

THE only investigations on record of the reactions occurring during the Bessemer blow are of charges containing a large percentage of manganese, with the exception of two partial analyses by Snelus and Barker of the. English method, where a low percentage of manganese was used. They do not give the analysis of the spiegel, nor do they report any graphitic carbon after the first stage of the process. Both report only traces of manganese after the first stage until the addition of spiegel. The slags corresponding to the samples of metal were not analyzed.

Jan 1, 1881

Mr. Brown : .That part of the Standard Company's plant which has been added since the publication of Mr. Leggett's paper, and is described in mine, renders the single-phase, alternating system, which Mr. Hale has called " unelastic," much more elastic than it had been. The original plant at Bodie was substantially the same as the Telluride plant mentioned in his paper. The machines came from the same shops, and were practically the same; but while the Telluride Company has changed completely to a polyphase system, the Standard Company has retained its original plant, but has belted on a directcurrent generator at the receiving end, thereby converting the water-power into electricity, electricity into power, the power into electricity, and finally again electricity into power for use in the mines. This is a roundabout course, to be sure, but it shows that there are possibilities even in the out-of-date single-phase system. The only point perhaps, that deserves particular notice with respect to the hoist is the fact that the rheostat, or starting-resistance, was not built originally

Jan 1, 1897

Cobriza can only be described as the Machu Picchu of the mining business. This relatively new mine of the Cerro de Pasco Corp. in Peru, subsidiary of The Cerro Corp., was put on stream in December 1967. The best way to get there is to go in the company's HelioCourier with pilot Paco Perez. The plane is mostly engine and the pilot is without nerves. The trip starts at an elevation of 12,000 ft at La Oroya and ends at the Cobriza air strip near the top of the Continental Divide at 14,200 ft. Perez says this is the highest air strip in the world. The flight is made at an altibude below many of the peaks and it is easy to pick out the Inca Trail which follows the ridge line of the top of the Andes. Inca ruins are also visible from the aircraft. The drainage pattern, with a surprising number of lakes and rivers, can be seen and so, too, can a great deal of structural geology and numerous agricultural settlements dotting the altiplano. Cobriza is in the monta[n]a on the east side of the Andes, which is characterized by tropical climate and vegetation, an abrupt change from the frosty mountain atmosphere. The mountainsides are precipitous and the bottoms of the steep valleys are channels for roaring rivers. Such is the setting of Cobriza, above the swift cataracts of the Mantaro, benched out precariously at about 8700 ft elevation. The mountains rise in majestic splendor and the sun comes up late and sets at 3: 30 on winter afternoons. One of the lowest of the Cerro de Pasco camps, it is the most remote.

Jan 11, 1969

By Edwin R. Phelps

In the year 1900 about 212 million tons of bituminous coal were produced in the United States. Almost none of this was produced by surface mines (Fig. 1), because there was no large equipment suitable for stripping overburden at that time. By 1915 the surface mines had built up their capability largely through use of the steam shovel to the point that they produced 2.8 million tons of the nation's total production of 443 million tons. Over the intervening years between 1915 and 1970 surface mining provided a continually increasing percentage of the nation's bituminous coal, stimulated by the growing availability of giant surface mining machines, some of which are presently capable of removing 220 cu yd of earth with one bite of their mighty buckets. In 1970 the nation's surface mines produced 244 million tons of bituminous coal, over 40% of the total national production. On the other hand, the nation's underground mines hit a peak of 560 million tons in 1920, dropped to a low of 273 million tons in 1961, and are presently on a very slow rise. Environmental pressures generally oppose surface mining, and have forced coal companies to consider more underground mining in future planning. Also, since strippable reserves are decreasing in the eastern states, an increase in underground mining is expected over the coming years. However, in the western states there are enormous reserves to be extracted by surface methods. Why has surface mining increased, while underground mining has decreased? It's largely a matter of economics. The cost per ton is greatly reduced by surface mining because of the relative ease of obtaining the coal. Also, there is a much greater percentage of coal recovery-nearly 85% in surface mines within the minable area, as compared to an average of about 50% in underground mines. Much surface mining recovers coal that could not be extracted by underground methods because of coal bed thinness, or multiple beds close together, split seams, the nature of the roof, and other geologic conditions. What are some of the limitations of surface mining? First of all, with presently available machinery it is difficult to surface mine at depths

Jan 1, 1973

A record $19.7 billion in minerals was produced by United States industries in 1963. This was some $800 million above the previous high established in 1962. Preliminary statistics compiled by the U.S. Bureau of Mines show that most metals, nonmetals, and fuels gained both in value and volume of production. The 1963 total represents the largest value increase since 1956 and continues an upward trend begun in 1959. Product.ion and value of all mineral fuels rose, with anthracite registering a remarkable 20% value increase. Nonmetals advanced 591 in value, gains exceeding losses by 213 to 1 among individual commodities. Heavier industrial demand and the settling of labor difficulties were among the factors contributing to increased output of such materials as iron ore, bauxite, molybdenum, lead, and zinc, which accounted for most in€ the growth in metal output. Silver prices continued to rise and, as a result, production value of that metal gained 132,.

Jan 2, 1964

[Separates of all the Technical Publications published in 1928 are available at Institute headquarters. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.; METAL MINING TECH- NICAL TRANS. PUBLI- TITLE AUTHOR MEETING VOLUME CATION AND PAGE* No. 50 The Eötvös Torsion Balance D. C. Barton New York Method of Mapping Geologic Feb., 1928 Structure 52 A Cartographic Correction for the C. A. Heiland New York Eötvös Torsion Balance Feb., 1928 61 Liquid-oxygen Blasting at Chuqui- H. C. Schultz, New York camata, Chile F. K. Middleton Hunter Feb., 1928 76, 108, 123 64 Working Methods of Practical Geo- Hans Haalck New York physics Feb., 1928 65 Experiments with Eötvös Torsion P. W. George New York Balance in the Tri-State Zinc and Feb., 1928 Lead District 74 Gravity Surveying in Great Britain H. Shaw New York Feb., 1928 75 The Computation of Eötvös Gravity E. Lancaster-Jones New York Effects Feb., 1928 82 Earth-resistivity Measurements in W. O. Hotchkiss, New York the Lake Superior Copper Country W. J. Rooney, Feb., 1928 James Fisher 83 Mining Methods and Records at the Roy W. Moore New York 76, 56, 90 United Eastern Mine Feb., 1928 98 Recent Results in Electrical Pros- Hans Lundberg New York specting for Ore Feb., 1928 101 Relation between the Oxygen Bal- G. St. J. Perrott, New York ance and Propulsive Strength of N. A. Tolch, Feb., 1928 Eight Gelatin Dynamites J. E. Crawshaw 102 Effect of Oxygen Balance of Gelatin G. W. Jones, New York Dynamites on the Gaseous Prod- G. St. J. Perrott Feb., 1928 ucts of Detonation 108 The Financial Report of a Min- Henry B. Fernald New York ing Company-Its Content and Feb., 1928 Meaning 116 What Duty to Support the Surface R. G. Bosworth New York Does a Subsurface Owner Owe? Feb., 1927 136 Comparison of Branch Raise and C. A. Mitke Los Angeles 76, 93, 103 Combined Shrinkage and Caving Sept., 1928 Methods 141 A Mining Company Balance Sheet G. F. Wolff New York Feb., 1928

Jan 1, 1927

By Alexander Field

THE rate of elimination of carbon largely controls the time required to make a heat of steel by the basic open-hearth process and to an important degree determines the cost of refining. Practical experience has led to the generally accepted belief that the use of slags relatively high in iron oxide, such as are required to bring about rapid refining, leads to a certain sacrifice of quality in the product. As a consequence, a compromise must be made between the exceedingly slow rate of carbon drop which would correspond to the ideal case and the rapid rate which would best satisfy the condition of minimum cost. An increase in rate of refining necessarily implies an increase in the concentration of iron oxide dissolved in the metal. However, even for the infinitely slow rate that corresponds to slag-metal equilibrium, the metal would contain a certain definite concentration of dissolved iron oxide. It is a matter of great practical importance, therefore, to determine the quantitative relation between the minimum or equilibrium concentration of iron oxide in the metal and the higher concentrations which must actually obtain in practice. The present paper is devoted to the development of certain equations, derived from the established laws of physical chemistry, which will enable this relation between rate of refining and the degree of oxidation of the metal bath to be computed from operating data. No attempt is made to exhaust the possibilities of this general method of treatment. In considering rate of refining, attention is mainly confined to rate of carbon elimination. However, the equations are of a more general nature and their application may readily be extended. The results of the preliminary calculations given herein indicate that increased rate of refining may have a decided effect in increasing the concentration of iron oxide dissolved in the metal. The uncertainty. which attaches to the calculated value for this relationship arises in part from probable errors in experimental data on which the calculations are based, and in part from the lack of complete or favorably disposed information on basic open-hearth practice.

Jan 1, 1928

By H. R. Aldrich

THIS paper is not a treatise on the theory and practice of magnetic surveying. It merely presents a diagram upon which have been plotted observations taken with the simplest form of magnetic instrument, the lowly dip needle, over a large area astride the Lake Superior syncline of northern Wisconsin. The exposures of the underlying formations are not sufficiently great in number nor fortunate in distribution to have provided the fuller understanding of the geology which has been secured by the use of the magnetic observations as an auxiliary tool or accessory in the hands of the geologist. The diagram (Fig. 2) in large part speaks for itself if studied in connection with the geological map (Fig. 1) for which it is the main control. It is presented to demonstrate the extent to which the use of such methods may aid in the solution of geological problems in a covered country. The diagram is probably unique in assembling the expression of such a wide range of formations, affected by so wide a range of secondary processes, and deformed by so many different structures in terms of magnetic variation. Few geologists outside of the Lake Superior country have had any first-hand experience in the taking of magnetic observations and the interpretations of the results in terms of geological conditions; nor have the Lake Superior men gone with the methods far afield from the mere tracing of iron formations. In more recent years the oil companies have gone heavily into investments in magnetometers, balances, and dip needles in the quest of concealed structural anomalies which are the favorable loci of petroleum accumulation. But these geophysicists come back from the fields with their collections of observations facing the question of interpreting the geological meaning of their magnetic anomalies.

Jan 1, 1928

By Thomas M. Drown

In experimenting in connection with Mr. P. W. Shimer (now chemist of the Thomas Iron Company, Hokendauqua, Pa.) on methods for the determination of silicon in pig iron, in order to find one which should be accurate and yet give results in a few hours, I have adopted the following procedure, which, as far as my experience goes, leaves nothing to be desired. About one gram of pig iron or steel is treated in a platinum or porcelain dish with 25 cubic centimeters of nitric acid (sp. gr. 1, 2). When action has ceased, 25 to 30 cubic centimeters of dilute sulphuric acid (one of acid and three of water) are added, and heat applied until the nitric acid is nearly or quite driven off. The heat of a water-bath is sufficient, though the process may be hastened by heating higher on a sand-bath. Water is then cautiously added (as soon as the free sulphuric acid is sufficiently cool) and the contents of the dish heated until the crystals of ferric sulphate are completely dissolved. The solution is then filtered as hot as possible, the residue washed first with hot water, then with 25 to 30 cubic centimeters of hydrochloric acid (sp. gr. 1, 12), and finally with hot water. After drying and igniting, the silica will be found to be snow-white and granular. The following are some results obtained by this method compared

Jan 1, 1879

By James Humes

The active mines in the Park City district at the present time are the Silver King Coalition, Daly-Judge, Daly West, and Silver King Consolidated. Several other companies, such as the Daly, American Flag, Ontario, etc., are doing considerable development work. In the Silver King Coalition mines the ore is a replacement of a dark siliceous limestone bed, varying in .thickness from 18 in. to several feet. In places the ore has reached a thickness of 25 ft. This limestone bed lies within 100 ft. of the underlying Weber quartzite. There are other lime beds, similar in appearance to this one, in the Park City formation, which is approximately 700 ft. thick; but not one of them has been found to contain any traces of ore. Directly under and in contact with the ore-bearing bed is another, composed of gray lime well studded with dark concretionary nodules; and this one is an unfailing indication of the proximity of the ore-bearing bed. These ore deposits make out from or have connection with some one of the ore-bearing fissures, which were undoubtedly the channels for the circulation of mineral-bearing solutions. It is therefore proper to run prospecting drifts in the fissures, although they seldom contain much ore. As a general rule, drifting in the fissures is not costly. Mining and mucking cost from $2.50 to $4 per foot, and very little timber is required. There are instances, as in the Daly fissure in the Daly-Judge mine, where the expense of keeping drifts open in the fissure is so great that it has proved economical to make the drifts in the foot-wall rock and run crosscuts into the fissure at short intervals. In the Park City mines it is not easy to determine beforehand the best method fir extracting the ore from a newly discovered ore shoot in the bedded deposits. While we may get one dimension from the drift run in the fissure, that will not give us a correct idea as to the other dimensions of the orebody. The fissures here referred to have a N. 35" E.

Jan 1, 1915

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962