Search Documents

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"' and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

By Ernest F. Burchard

A Reconnaissance of the manganese- and chrome-ore deposits of Cuba was made by the writer, as a representative of the U. S. Geological Survey, in company with Mr. Albert Burch of the Bureau of Mines, under instructions of the Secretary of the Interior, in the spring of 1918. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the island. The object of the study was to obtain authentic information for use of the United States Government as to the location, character, quantity, and availability of the manganese- and chrome-ore deposits in Cuba. Accordingly, the work comprised examination of such deposits as seemed to be of promise, without regard to stage of development, with a view to a determination of the quantity and quality of ore likely to become available for shipment during 1918 and 1919, and of the tonnage of ore in reserve. Wile it was possible to visit most of the deposits that seemed to be of promise, there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Moreover, the necessity for paying particular attention to the ore deposits and the mines precluded the possibility of making more general studies of the geology of the region, and of making satisfactory collections of country rock and of fossils, and so for other details as to the geography and geology of Cuba the reader is referred to the report by Hayes, Vaughan, and Spencer.l Mr. Burch returned to the United States about 10 days in advance of the writer, who continued, in company with Sr. Montoulieu, investigations of reported deposits in Pinar del Rio, Matanzas, and Santa Clara Provinces. On his arrival in Washington, Mr. Burch submitted to the Director of the Bureau of Mines a summary of the results of the work to date. Later the writer published, as Press Bulietin 190. 380 of the U. S. Geological Survey, a statement concerning the chrome and man-

Jan 1, 1920

THIS paper presents briefly some of the principal results of 3 ½ months field work during the summer of 1938 in the Chichagof mining district, southeastern Alaska. The report is preliminary and presumably will be followed later by a more complete report to be published by the Geological Survey. The paper is concerned principally with the structural geology of a block of steeply dipping graywacke as revealed underground in the Hirst Chichagof and the Chichagoff mines, the two principal mines of the district. The two mines have produced about $16,000,000 worth of gold and silver. The attitude of the graywacke, which is locally cut by dikes and sills of aplite, is remarkably uniform and trends about N. 62º W. The average dip is about 67º SW. The graywacke is cut by large faults, the best known of which are the Hirst and the Chichagof, whose average trends are about N. 30ºW. and average dips about 75º SW. The faults at some places split into the bedding of the graywacke and at others are deflected from their normal trends for considerable distances along the bedding. The relative movements along the faults was northwest and up at about 30º for the south- west or hanging-wall sides. The ore bodies are elongate quartz lenses in the faults. Most of the quartz is mineralized but locally large quartz masses are too low grade to be mined. The emplacement of the ore bodies appears to have been structurally controlled in large part by the intersections of the faults with the bedding surfaces. Places where the faults split or are deflected appear to have been particularly favorable places for ore deposition. There has been some post-quartz movements along the faults but it is thought that such movements have not been extensive enough to greatly modify the original positions and shapes of the ore bodies.

Jan 1, 1939

By Newell G. Alford

With the workable area of coal prospected and known as to workability and quantity and sampled and tested for desired quality comes the determination of the projection and method of working. The best method will be the one supplying the greatest degree of safety, the most merchantable product, the minimum average cost per ton with the largest yield of recoverable coal. Based on coal elevations, taken at the bottom of the seam on all known outcrop exposures, prospect openings or drill holes, coal contours are made on the map to be used in developing the mining plan. The contour interval should be as close as available information will permit. For general utility in layout of mining, haulage, drainage and ventilation, a map scale of 400 ft. per in. is preferable. In mountainous sections, location of the main out- crop opening or hoisting shaft is often limited by the available railroad route and amount of land level enough for a plant site. In level country, where a tipple and hoisting shaft may be placed at will, choice of the plant site should depend on the minimum average underground haul for the total coal to be worked to the new

Jan 1, 1932

HUDSON MAXIM, Brooklyn, N. Y.-Immediately after the creation of the Naval Consulting Board, Admiral Strauss, Chief of the Bureau of Ordnance of the Navy, told members of the Board that the most important problem for the scientists to solve was erosion in large guns. The Navy, for years, had been working on the problem with marked suceess, but there was much yet remaining to be accomplished. As Chairman of the Committee on Ordnance and Explosives of the Naval Consulting Board, I communicated with several experts in the manufacture of steel, principal among whom was Prof. Howe. He generously agreed to help in every way possible, and the work that he has done and the time that he has spent upon it can he appreciated only by reading his paper. Prof. Howe asked for some rings. from a, certain 14-in. gun which Admiral Strauss had mentioned in particular, and in which, he had informed us, at each shot the bore of the gun, was enlarged about 0.001 in.,' and that after a relatively small number of rounds it was considerably eroded. It has puzzled scientists for a long time to account for the peculiar erosive effect produced by the powder gases in a gun, arid: what Prof. Howe has done in his paper is worthy of Sherlock Holmes. He is a veritable Sherlock Holmes of science.

Jan 4, 1918

By B. W. Frazier

IN the numbers of the Engineering and Mining Journal of June 27th and July 11th, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced to the same standard of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given -by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of the pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part of the furnace, by the dissocia¬tion of carbonic oxide, is again converted into carbonic oxide or

Jan 1, 1875

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By Clark Millison

The core recorder, a mechanical instr-ent for determining the exact depth at which core is recovered, drilled up or lost, is described. Examples of charts from the recorder are explained and interpreted. The uses of the core recorder are discussed. INTRODUCTION In the experience of geologists and engineers during coring operations on drilling wells, many will recall the times when a full core was not recovered and particularly when the requirement was urgent that they know exactly what part of the core was lost. To make this determination, the core recorder was designed. Its uses are many, and only the most obvious will be presented here. Although this discussion will be limited to drilling wells for petroleum, the core recorder can be used in any type of coring operation. The principle of the core recorder is the proportional reduction of the motion of core entering or dropping out of the core barrel to a stylus moving in such a manner as to record the reduced motion on a chart. The time element is registered on the same chart by the revolution of a clock which turns the chart drum. Thus the exact amount of core entering or dropping out of the core barrel is charted and the time of such entry or exit from the core barrel is precisely correlated to the depth at which the core is recovered or lost. Lack of movement of the stylus which is revealed by the continued revolution of the chart drum indicates that no core is entering the barrel. The principles are accomplished by an instrument placed inside of the core barrel. A cylinder which contains the clock and mechanical apparatus has a diameter smaller than that of the core barrel. Near the top of the cylinder is an eighteen hour clock which turns the drum that contains the chart. Near the bottom of the instrument is a serrated wheel which by friction against the inside of the core barrel is turned as core enters or drops out of the barrel.

Jan 1, 1949

By C. G. Dunn

Identification of the kinds of orientation relationships that may exist among crystals is an important problem in the metallurgical field. As an aid to its solution standard orientations of several orders of twins would be very useful for rapid analyses to discover high-order as well as low-order twin relationships. Although data have been published that give orientations for three generations of twins, these data are not readily useful in the form presented; i.e., in a stereo-graphic projection with one pole per orientation.' However, accurate data based on calculations of the positions of all {1001 planes for such groups would be very useful when presented in tabular form. Therefore, calculations have been made for a group of four orders of twins and the data are listed in Table 3. Illustrative applications are considered briefly, with the idea of pointing out what may be done with large groups of orientations. Method of Computing Orientation OF a Twin It is common practice to describe the orientation of a crystal in terms of the positions on a stereographic net of the poles of certain planes of the crystal. A single position on a net may be given in terms of two angle variables, two sets of which appear in the following equations: Polar Net Wulff Net x = , sin ?p cos Fbp x = r COS ?w y = r sin ?p sin Fp y = r sin ?w cos Fw % = r cos ?p z = r sin ?w, sin +, The three numbers z, y and z determine a length r as well as a direction (0, 4) in an X, Y, Z coordinate system. In the present case, r will be set equal to (h2 + k2 + L2)1/2, where h, k and I are the usual Miller indices for a crystallographic plane, a restriction that facilitates determination of the positions of poles of new planes from those of old or known ones,2 as will become evident later. Furthermore, since twinned lattices have certain planes in common, it is an easy matter to determine the orientation of a twin of a crystal if the orientation of the crystal itself is known. We start therefore with a crystal of known orientation (positions of three {Ioo} poles given) and determine where the cube poles occur in first, second, third and fourth-order twins. Methods for identifying twinned lattices and for making the calculations to find the orientation of a twin have been published.3,4' Reference 4 will be illustrated in the calculation of the orientation of a twin, even though this method differs from the one used by the writer in obtaining the following data on four orders of twins. Consider a crystal S and its twin A1, A' being one of the four {112} or {III} type* first-order twills of S. The orientation of S—i.e., the positions of poles of (I00)

Jan 1, 1945

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By Sidney Powers, Alfred C. Lane

This paper aims to present the results of an investigation concerning gravitative differentiation in lava flows, based on a quantitative microscopic and chemical study of a Triassic basalt from Nova Scotia, and confirmed by data secured from a study of certain Keweenawan ophites. At Cape d'Or, Nova Scotia, near the head of the Bay of Bundy, marine erosion has exposed a series of Triassic basalt flows in which copper has been sought for a number of years. Studies of the thickest flow of the series with regard to volumetric composition, specific gravity, and grain have been made by the junior author, and measurements by students at Tufts College, together with confirmatory observations of the same nature on this and other flows by the senior writer, and chemical analyses made by the Division of Chemistry, Mines Branch, Ottawa,' all show differentiation in lava flows comparable to that in intrusive bodies. The work was made possible by the availability of the drill-cores, the property of Tufts College, and emphasizes the desirability of the study of drill-cores from other localities. Measurements of the specific gravities of certain Keweenawan lava flows of Michigan by the senior author, from material collected in 1915, will be given as a comparison to those of the Cape d'Or flow. It has been found that the specific gravity of drill-cores, or volume per cubic foot, can be readily obtained by measuring their dimensions. This can be done to an accuracy of within 1 per cent. in pieces of core over 100 mm. in length by using a micrometer gage for the diameter, and taking the average of six measurements of the diameter; and the average of four measurements of the length made with a finely graduated ruler. Then, after weighing them, the weight in grams per cubic centimeter, or what is practically the same thing, ounces per cubic foot, is obtained. System-

Jan 1, 1916

By Hiro Minagawa

Japan's contact with the mining industry of British Columbia began as far back as 1952 with the first shipment of iron ore from the Texada mine. Five years later, the Big Three steel mills of Japan-that is, Nihon Kokan Kaisha, together with Yawata and Fuji Steel Mills-dispatched a coal survey mission to inspect coal mines in British Columbia. This resulted in 100,000 tons of coking coal being initially imported by Japan from western Canada in 1959. Also in 1959, Yawata, Fuji, NKK, Kawasaki and Sumitomo sent an iron ore survey group to Alaska and Canada. During the preceding year, Nippon Mining Company and Sumitomo Metal Mining Company initiated a project whereby they would assist in the development of Cowichan Copper on Vancouver Island. As a net result of this activity Japanese mining groups, who had heretofore concentrated on Southeast Asia and South America, finally turned their eyes toward Canada. It was in the fall of 1960 that the government of Japan, in order to keep pace with Japan's rapid economic development, announced a long-range economic plan whereby her gross national income would be doubled by 1970. This had the effect of further propelling Japan's desire to develop sources of raw material supplies abroad. With the development of Craigmont Mines and the signing of a long-term contract to export copper concentrates to Japan, and with the Sumitomo group's extending financial assistance to develop Bethlehem Copper, Canada itself began to realize that Japan was indeed a very important market for British Columbia. A number of surveys to develop mines in British Columbia was begun with an eye on Japan as the major market, and the activity has continued to this day.

Jan 12, 1963

By George E. Thackray

In December, 1894, the Cambria Iron Company made a number of heats of Bessemer steel to be used in structures by one of its customers, subject to inspection and tests by a firm of consulting engineers, one of the requirements being that the material should riot exceed .08 per cent. of phosphorus. In other respects the requirements were such that they could only be met by material of good quality; but the general spe cification is not introduced here, as it is not the purpose of this paper to deal with anything except certain difficulties encoun tered in determining the phosphorus-content of the material in a manner satisfactory to both seller and buyer. Preliminary determinations of phosphorus were made in sample-ingots from each of the heats from which material was rolled for the order in question, and these preliminary chemical tests, made in the laboratory of the Cambria Iron Company, showed that, with very few exceptions, every heat was within the prescribed limit of phosphorus. After the material had been rolled, sample-drilling8 of finished material were taken from the various heats in the regular manner in use at the works, these samples being thoroughly mixed and divided into two parts, one of which was analyzed at the works' laboratory and the other sent to the inspecting engineer. Several hundred determinations were made from this mate rial without reaching an agreement between the work of the inspector's chemist and that of the works' chemist; but as it is not the object of this memorandum to treat of this part of the subject at length, it is considered sufficient to present herewith only a few of these first determinations. The analyses given in Table I. are those of the original series made on the heats which were afterwards resampled for final determination by an arbitrator; and they are selected for this reason, as the entire " comparison is thus rendered more complete.

Jan 1, 1896

By JAMES GAYLE

(Presented at the Washington meeting, May 3, 1905, and simultaneously sent to the Iron and Steel Institute, for presentation at the meeting of that Society in London, May 11, 1905.) IT is to be regretted that the data respecting the use of dry-air blast, which was presented to the Iron and Steel Institute at its meeting in the United States, in October, 1904, should. have been restricted to the period from August 25th to September 9th inclusive, and from September 17th to 30th inclusive. In order to present the paper at all it was found necessary to limit the record of operations to the period above stated. In the discussion of the paper it would appear from the conclusions of some participating therein, that they have been placed at some disadvantage in considering the economies obtained through the use of dry-air blast, by reason of the data covering such a short period. It is the purpose of this communication to present in detail the record of operations of the Isabella Furnaces from November, 1904, to March, 1905, inclusive, as shown by the furnace-records. The month of October, 1904, is not included, as the furnace using dry-air blast was stopped several times for repairs, and while the record was a very good one considering these interruptions, yet it was not a continuous one. The record for Furnace No. 1 using dry-air blast, and the comparison with Furnace No. 3 using natural air for the month of November, 1904, is set forth in Table I. By a reference to my former paper it will be noted that the month of November is the beginning in this country of the winter period, when the atmosphere decreases rapidly in humidity. The month of October being the transition month in the autumn and April in the spring, and furnaces using natural air approach more closely, from November on, to the conditions obtained by the use of dry-air blast. The data given in

Jul 1, 1905

By John P. Harmon

This paper was written with two objects in view: (1) To describe in detail what has been done toward the ventilation of the main unit of the Portovelo mines and the results; (2) to give information that may be useful to anyone who may have to make a preliminary mine ventilation survey, with recommendations for the improvement of the existing system and finally the maintenance of the improved system. General Description The mining operations of the South American Development Co. at Portovelo, Province of El oro, Ecuador, are described here only briefly, as a full discussion does not fall within the scope of this paper. The orebodies are of the steeply dipping, gold quartz vein type, averaging about 2.0 meters wide. As shown in Fig. 1, the ore chutes are relatively far apart, making considerable development work necessary before connecting raises can be driven between the levels. Faulting' on a large scale and a parallel vein system have made long dead-end drifts and many crosscuts necessary in the exploration of veins. The ventilation of these dead ends is described under Auxiliary Ventilation. The method of mining2 is the filled rill stope method, similar to the method that is largely employed at the Butte mines. The main shaft of the mine is in the Amarillo Valley, on either side of which mountains rise abruptly to a height of several hundred feet above the collar of the shaft. Entrance is made to the mine: (1) Through the American shaft, which extends vertically from the surface to a depth of 1100 ft., of which only the first 700 ft. are in active use at the present time; (2) levels are driven from the American shaft at intervals of 30 m. (100 ft.), of which only the third, fifth and seventh levels need be considered in the ventilation problem; (3) adits at intervals of 30 m. (100 ft.), with a few exceptions, above the collar of the American shaft.

Jan 1, 1931

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By George B. Holderer

The relation between man-hours of labor and production may be correlated for any industry, and already it has been widely used in piecework studies. It is not in general use as yet for recording labor efficiency of an enterprise or an industry. An exception to this is the Cement Institute, which tabulates the man-hours used in each operation and thus gets the total man-hours per barrel of cement. The writer knows of one steel company that keeps a complete record of man-hours for every operation from mining the ore to finishing the product. No doubt many others find the information useful, and such a study could be of value to the mineral industries.

Jan 1, 1937

By Harry Power

THE relative merits of air and natural gas as propulsive agents in pressure drive operations have been discussed for a number of years. When air or gas is introduced into the sand, various factors lead the operator to the selection of what he believes to be the proper propelling medium; but when the question of relative drive effect is raised, several physical and chemical premises must be taken into consideration in arriving at a conclusion as to the superiority of one medium over the other. Dow and Calkins1 and Beecher and Parkhurst2 have contributed fundamental experimental work on the effect of dissolved gas in lowering the viscosity and surface tension of crude oil. Herold3 and Tickell4 have indicated that whatever type of reservoir control obtains, gas plays other important parts in the movement of oil towards the well, namely: 1. The propulsive and expansive force of the gas. 2. The "Jamin effect," or resistance to the movement of oil in a porous media due to the formation of gas bubbles. When quantitative studies are made, parallel conditions must be selected whereby we may say definitely whether air is superior to gas as a driving medium, or vice versa. Examples of similar conditions are not easy to find in the field. However, in the laboratory we can make determinations which may lead to general conclusions when applied to the field. The- experimental and research work described here was started at the laboratories of the University of California in January, 1927, and completed in private laboratories at Tulsa, Okla., in February, 1928. The apparatus used was designed especially for the work.

Jan 1, 1928