Search Documents

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary): I think very highly of the novel and ingenious device of Prof. Richards for analyzing the movement of the various elements of the jig; it is a method that certainly seems to promise valuable results, if we could only make certain that these various indicator-appliances have no effect upon the action of the jig. I would like, however, to suggest that in future experiments the connection between the plunger indicator-rod and the pencil should be made by means of parallel motions, so as better to reproduce the rectilinear motion of the piston. I should expect, if this were done, that the " curve " of the plunger in the Harz jig, at any rate, would be represented either by straight lines or else by quite regular curves, according to the method by which the plunger is set in motion; the apparent combinatioil of straight line and curve seems difficult to explain. With respect to the water-curve, I am afraid I am completely at fault, but no doubt Prof. Richards can explain my difficulty. In Fig. 2, the areas of the screen-side and the plunger-side of the jig are equal. If the piston be a fair fit and the bottom of

Jan 1, 1897

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K's) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.' In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By R. A. Pallanch

Probably one of the most perplexing problems with which a mill operator contends is the proper evaluation of his mill results. True, he accurately determines his recoveries of metals and grades of products monthly, weekly, and often daily. These figures do not of themselves directly translate to mill economics. When one figure is unusually good there may be an offsetting circumstance. The advantage of high lead or zinc concentrate grade may be offset by poorer recovery; high lead recovery may be offset by poorer zinc recovery, or vice versa; and so on. Besides, grades or recoveries may not of themselves mean more than a reflection of the grade and character of the ore during the period under study. What the operator sorely needs is some one measuring stick that tells him when he has achieved his greatest return, regardless of grades or recoveries—for if he knows his methods and practices are yielding the optimum return he need no longer concern himself with the assays of products and tailings, or the corresponding distribution of metal values. At first blush it would appear that the obvious answer to this is the actual money return to the mill. Paradoxical as it may seem, however, money return does not make a dependable yardstick any more than do grades and recoveries, as ore condi- tions would vary enough to bring about greater money return during periods when the actual metallurgical work is not as good. The mill operator, of course, should always aim for the greatest return on the ore, once it is in the mill bins, with proper attention always to mill treatment cost. The need of a proper yardstick becomes more imperative with the increasing complexity of the problem. In the case of a simple, single-product operation on a fairly uniform ore, in which only one metal is of significant importance, the need is not great, as grade and recovery pretty well tell their own story. At the other extreme is the operation that makes three or four separate marketable products from a complex mixture of heterogeneous ores that vary tremendously in individual metal contents and ratios, degree of oxidation, and other characteristics, and in which gold, silver, copper, lead and zinc are all significant values. Economic Recovery The first attempt at obtaining a proper single yardstick for a fairly complex ore with which I am familiar is the use of the ''Economic Recovery" term at the lead-zinc flotation mill of the Sunnyside Mining and Milling Co., Eureka, Colorado. This method had been applied there early in Sunnyside flotation-mill history (not later than 1920) and credit for the innovation I believe belongs to Messrs. Kuryla and Marquand. The term "Economic Re-

Jan 1, 1949

By L. L. Wyman

THE resultant embrittlement caused by the exposure of oxygen-bearing copper when hot and exposed to reducing gases has been the subject of many studies.1 Little attention, however, has been given to the possible embrittling effects due to atmospheres or conditions that under some circumstances might be the source of a reducing gas. At rather infrequent intervals there occur reports of copper becoming embrittled during normal annealing cycles in commercial steam-atmos-hered furnaces such as customarily are used for this operation. As might be expected, several other factors exist-such as oil, dirt on the wire, or in the furnace, or metallic surface contacts that might produce reducing gases and be the source of the trouble. However, in consider-ation of the statement made by Ruder,2 it would seem that under some conditions steam itself might prove to be the source of trouble. A consideration of the amount of the dissociation of water vapor up to temperatures of the melting point of copper shows that' the amount of hydrogen that could come from this source is far too minute to account for any embrittlement. What such information does not tell is what will happen at the surface of copper when subjected to steam at elevated temperatures, for entirely different conditions may persist, which would account for Ruder's observation. Furthermore, there are no data as to what might happen at the surfaces of other materials present, the result-ant of which might affect the condition of the copper present. For this reason, it was decided to make a series of experiments com-parable to those previously conducted by the writer,1 which would clarify the effect of the steam on copper, and in copper in the presence of steel.

Jan 1, 1940

By Parke A. Hodges

CHROMIUM, one of the most vital of the strategic metals, has constantly increasing importance as research expands potential uses in alloy steel metallurgy. All signs point to a steadily growing use for chrome ore, and the general subject has received a great deal of attention recently.1 A relatively little known country, Southern Rhodesia produced a total of 5.949 million tons, or 18.6 pct of the total world chrome output, between 1906 and 1950, according to figures from the U. S. Dept. of Commerce. According to U. S. Bureau of Mines figures, Southern Rhodesia produced 291,525 tons in 1950 and 300,267 tons in 1951, or approximately 13 and 11 pct, respectively, of world production for the two years. In 1953 the Rhodesian Vanadium Corp. produced about 85,000 tons of which probably 7,000 tons were concentrate. Production by other companies was high. Large in themselves, the figures assume even greater significance because most of this output is of metallurgical grade.

Jan 8, 1954

By R. D. Sprague, C. B. Richardson

The year 1938 was the most active and successful in the history of the oil industry in southern Louisiana. Drilling showed a 16 per cent increase over that of 1937, with a total of 538 wells drilled, which yielded 315 oil wells, 19 distillate wells, 4 gas wells and 200 dry holes. Nineteen new fields were discovered during the year, all but three of which were completed by plugging back to sands previously drilled through. Electrical logging played a large part in these new discoveries as well as in the discovery of new sands during routine development of fields. Fourteen of the new discoveries produced oil, and five produced only gas and distillate. Southern Louisiana continues to lead the world in depth of drilling, which is in part due to the great thickness of comparatively young deltaic sediments near the coast and the existence of numerous sands. The present development is rather evenly distributed over a coastal strip 100 miles wide. New Fields North Tepetate, Acadia Parish.—Atlantic Refining Company's No. 1 Klumpp was completed for a new field through perforations from 7960 to 7970 ft. The initial production was 65 bbl. of 54" gravity distillate and 4 million cubic feet of gas daily through a 1/4-in. choke with tubing pressure of 2850 Ib. and casing pressure of 2930 lb. The well is in see. 12, 7 S., 2 W., just north of Tepetate field. It was drilled to a depth of 8705 ft. and plugged back for its final completion. Atlantic's NO. 2 was completed in a new sand at 8300 ft., also for distillate. South Crowley, Acadia Parish.—Humble Oil and Refining Company's No. 1 Boyd Finch was completed in July 1938, as an oil well through perforations from 7318 to 7325 ft. after plugging from a total depth of 10,222 ft. After making several hundred barrels of oil, the well went to

Jan 1, 1939

By C. B. Richardson, R. D. Sprague

The year 1938 was the most active and successful in the history of the oil industry in southern Louisiana. Drilling showed a 16 per cent increase over that of 1937, with a total of 538 wells drilled, which yielded 315 oil wells, 19 distillate wells, 4 gas wells and 200 dry holes. Nineteen new fields were discovered during the year, all but three of which were completed by plugging back to sands previously drilled through. Electrical logging played a large part in these new discoveries as well as in the discovery of new sands during routine development of fields. Fourteen of the new discoveries produced oil, and five produced only gas and distillate. Southern Louisiana continues to lead the world in depth of drilling, which is in part due to the great thickness of comparatively young deltaic sediments near the coast and the existence of numerous sands. The present development is rather evenly distributed over a coastal strip 100 miles wide. New Fields North Tepetate, Acadia Parish.—Atlantic Refining Company's No. 1 Klumpp was completed for a new field through perforations from 7960 to 7970 ft. The initial production was 65 bbl. of 54" gravity distillate and 4 million cubic feet of gas daily through a 1/4-in. choke with tubing pressure of 2850 Ib. and casing pressure of 2930 lb. The well is in see. 12, 7 S., 2 W., just north of Tepetate field. It was drilled to a depth of 8705 ft. and plugged back for its final completion. Atlantic's NO. 2 was completed in a new sand at 8300 ft., also for distillate. South Crowley, Acadia Parish.—Humble Oil and Refining Company's No. 1 Boyd Finch was completed in July 1938, as an oil well through perforations from 7318 to 7325 ft. after plugging from a total depth of 10,222 ft. After making several hundred barrels of oil, the well went to

Jan 1, 1939

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.'' This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By R. D. Lee

A simplification of the method of Hurst and McCarty for conducting potentiometric model studies by the single probe method is presented along with experimentally determined invasion patterns for certain idealized flow problems. The analytical solution for one class of these problems is given. Finally, a general description is given of a newly developed instrument which permits direct mapping of flow lines and determination of transit times in potentiometric-model studies. Introduction The object of this paper is to present: I. A simplification of the method of Hurst and McCarty for conducting poten-tiometric-model studies of oil and gas reservoirs by the single probe method. 2. Results of a series of studies of certain idealized flow problems and the general conclusions to be drawn therefrom. 3. A description of a new instrument, the Chronocartograph, which greatly reduces the labor and time required for conducting potentiometric-model studies. Certain general conclusions may be drawn as results of the investigation of the idealized flow problems. They are: I. Injection and extraction areas should be separated by as great a distance as conditions permit since, in general, the recovery prior to first breakthrough tends to vary as the square of this distance. 2. Little advantage is to be gained by use of more than eight injection wells or groups of injection wells for the case of circular productive limits. 3. Elongated shapes of productive limits are best exploited by injection on the extended major axis only, with a line of extraction wells lying on the major axis. 4. The use of peripheral injection wells for elongated shapes is permissible, if necessary, but requires extension of the line of extraction wells. The exploitation of an oil or gas field is effected either by the expansion of the gas and oil, or by their displacement by another fluid. Both methods may be used simultaneously. When the displacement of the oil or gas is the controlling factor there arises the problem of mapping the progress of the boundary between the fluid in place and the displacing fluid. This problem is of particular interest in the operation of a cycling project in a gas-condensate field, where the wet gas is produced from one or more wells, commonly called "extraction wells.'' This wet gas is taken into a processing plant where the condensate is removed. The remaining "dry" gas is injected back into the field through one or more wells, called "injection wells," both to conserve the gas for future use and also to maintain the pressure in the field. In an operation of this type it is essential to anticipate the manner in which the dry gas will spread through the field, because the ultimate recovery of the wet gas depends

Jan 1, 1948

By Joseph Kelly

DEPLETION of anthracite resources in Lackawanna County, Pennsylvania, has forced the recovery of coal tracts formerly considered unminable. Chief among these are the large areas of outcrop coal lying on a heavy pitch on the mountain sides, abandoned thirty or forty years ago as too costly and too hazardous to mine. The old companies, in many instances, stopped their chambers 80 or 100 ft. hack from the actual outcrop, and then dropped back another 100 ft. before starting to rob the pillars, thus leaving large areas of coal. Recovery of this coal naturally leads to mining hazards not encountered years ago. The first step is to sink a slope from the surface with the pitch of the vein, and then drive counters across the pitch as close to the robbed area as proper protection for the lower side of the -counter will permit. Next, the old chambers are advanced or new ones driven in the solid, as the conditions require. As these chambers approach the outcrop the real safety work begins-that of preventing the miner from being buried or locked in by an avalanche of mud.

Jan 1, 1936

By John A. Oberteuffer, Ionel Wechsler

High gradient magnetic separation, first introduced in 1968 as a means for the removal of very fine magnetic contaminants from clay, is no longer a new technology. Applications to a number of solid-solid and solid-fluid separation problems are now being exploited. Recent pilot tests and full-scale industrial installations of high gradient magnetic separators and filters have established their commercial viability and have demonstrated their superiority both in efficiency and cost effectiveness to conventional prior-art methods for water treatment and mineral processing. In high gradient magnetic separators, the magnetic trapping force for fine, even weakly magnetic particles is greatly increased over those available in previous magnetic separators. These very strong trapping forces are created on the edges of fine filamentary ferro- magnetic materials in the presence of a strong background magnetic field. In the basic cyclic high gradient magnetic separator, particles are trapped in the filamentary matrix until it is loaded, at which point the magnetic field is turned off, and the filter is back- flushed. Applications of cyclic high gradient magnetic filtration for water treatment include filtration of waste and process waters in steel mills. Treatment of hot rolling mill scale pit effluent and cold rolling mill emulsion has been successfully tested, and 2-meter diameter SALA-HGMF® magnetic filters have been installed at Japanese steel companies for the treatment of recirculating scrubber waters in a de-gas- sing system. A second major application in water treatment is for the polishing of recirculating waters in power and steam generating systems. High gradient magnetic filters can operate under conditions of

Jan 1, 1980

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By F. G. Tickell, R. C. McCurdy, O. E. Mechem

The behavior of fluids in the voids of a rock is fundamental to the study of many of the problems of oil-field development and production. For it is by virtue of these openings between grains that oil and gas are able to move through the rock, to be contained by the rock, and to pass from the rock into the well. The capacity to contain fluids is measured by the porosity of the rock, and the ease of fluid movement is governed by the permeability. When the engineer wishes to estimate the amounts of oil and gas in an underground reservoir he is often concerned with the porosities of the rocks and, when dealing with problems relating to rate of production, he is more likely to be interested in the permeabilities of the rocks. Rocks are permeable because they are porous, but they may be porous without being permeable. Clays are very porous, and yet they are impermeable from a practical standpoint. Attempts have been made1 to correlate permeability with porosity for certain rock members but, where a definite relationship between these two properties is found to hold, it is purely fortuitous and local. Porosity and permeability do not necessarily bear any quantitative relationship to one another. The porosity of a substance is the percentage of void volume to bulk volume. The petroleum engineer is usually interested only in the inter-granular voids that are accessible to fluids. In measuring porosity he does not wish to include scaled openings. The measurement he desires is one of "available porosity," otherwise called "apparent porosity." The porosity of a natural aggregate of solid grains, such as a sandstone or clay, is governed by: (1) Grain-size distribution, (2) angularity of grain, (3) colloidal content, (4) degree of compaction. It is not difficult, for unconsolidated rocks, to measure the effect of any one of these when it alone is varied, and then to predict what the effects on porosity will be for such single variables. It is very difficult, however, if not

Jan 1, 1933

By AIME AIME

ELECTRICAL methods of geophysical exploration attracted major attention at the three sessions devoted to geophysics on Monday and Tuesday. At the opening' meeting Monday morning Hans Lundberg gave the paper by himself and Folke Kihlstedt; he described the use of the Racom, discussed last year, and the method whereby it is possible to eliminate all but subsurface, effects in electrical exploration. In the discussion Theodor Zuschlag pointed out some of the theoretical considerations behind the field procedure. Karl Sundberg's paper on the effect of impregnating waters was presented by title only, and S. F. Kelly then gave an abstract of a paper on the electrical properties of ores, by J. J. Jakosky, R. N. Anderson and Clyde H. Wilson. , This dealt with an exhaustive series of laboratory tests on the variation of -conductivity of ore specimens with the frequency of the energizing current, and of the effect of moisture content in typical clays and gouges on their conductivities at various frequencies. Considerable discussion was provoked during which the authors came in for some-criticism on their measuring circuits and for their assumption that a solid conductor could be compared with linear ones. They were praised, however, for making a start toward a compilation of resistivities for ores and rocks. Dr. Slichter disagreed with them that the conductivity of an orebody was primarily capacitive. He also called attention to the fact that it was high time geophysicists adopted the standard physical expression of ohm-,centimeters or ohm-meters to express resistivities. This same point was the burden of the next paper,. "Uniform Expression for Resistivity," by Sherwin F. Kelly, presented by title only.

Jan 1, 1932

By W. B. Morrison

The principal factors influencing the total percent elongation of a lead-tin eutectic and several low-alloy steels which exhibit superplasticity were investigated. These factors are: a) Strain-rate sensitivity of the stress (m). b) Specimen geometry; in particular, diameter-to-length ratio (d0/l0), and surface irregularity (e.g. notches). A feature of the tensile deformation of a superplastic alloy is the early appearance of a neck which continues to extend throughout the test. As a result the total elongation is directly related to the diameter-to-gage-length ratio. The strain-rate sensitivity of the stress varies during extension, mainly because of microstruc-tural changes. A satisfactory correlation exists between the minimum strain-rate sensitivity and total elongation, as indicated in the equation shown below. Notches cause a considerable reduction in total elongation and their effect is greatest at high values of strain-rate sensitivity. An initial notch depth exists below which there is no appreciable effect on elongation. An equation relating elongation to strain-rate sensitivity and specimen geometry is proposed, THE total percent elongation of a tensile specimen is usually regarded as a measure of superplasticity. However, little attention has been given to the fact that total elongation is also a function of specimen diameter and gage length, even though the importance of geometry has long been recognized in the tensile testing of materials in which elongations are relatively small.* In the present study, the effect on superplas- tic extension of the ratio of specimen diameter to length was investigated and an analysis was made of strain distribution along the gage length. Superplastic alloys are characterized by having a flow stress sensitive to strain rate but relatively insensitive to strain.2"' In an earlier study,5 it was found that the strain-rate sensitivity of several low-alloy steels changed during the test and that the minimum value correlated best with total elongation. In the present study, the variation of strain-rate sensitivity during the straining of a lead-tin alloy was investigated. EXPERIMENTAL PROCEDURE Lead-tin eutectic alloy (32 pct Pb 68 pct Sn), made from high-purity lead and tin, was cast in the form of 1-in. diam rod. The rod was cold-rolled in stages to 0.25 in. diam and then swaged to 0.125 in. diam. Samples were cut from the rod at various stages of the mechanical working process. Tensile test specimens were then made by attaching threaded steel ends to the rods by an epoxy-base thermosetting adhesive which required a setting treatment of 2 days at room temperature. The rods were seated in the steel ends in holes approximately 0.01 in. oversize. The test pieces thus made were of various diameters and gage lengths. These were stored at a temperature of about -70°C (-94°F) until required for testing. The distribution of strain along the gage length of a specimen was determined at various stages of the tensile test. The lead-tin alloy was superplastic at room temperature and direct observations during testing were simple. The gage length was divided by reference marks into five initially equal units. These reference marks were made with ink and were reinforced during the test when the initial marks became faint. Photographs were taken, at intervals, of the deforming specimen and measurements of the elongation in each of the gage units were made on these photographs. Tests were also done on several superplastic low-alloy steels whose properties were described earlier.5 The chemical compositions of these steels are given in Table I. A diagram of the notched tensile specimen used in the steel tests is shown in Fig. 1. The specimens were tested at 900°C (1650°F) in a furnace through which a mixture of He + 2 pct H was continuously circulated.5 RESULTS Strain Distribution. Approximately 20 tests on lead-tin alloy specimens were conducted to determine the strain distribution during the test. An example is shown in Fig. 2 of the strain distribution in the gage

Jan 1, 1969

By Jack Washburn, E. R. Parker

Kinking in zinc single-crystal tension specimens was observed under conditions of low stress and high temperature. Kinking is discussed in relation to other plastic bending phenomena on the basis of dislocation theory. Experiments on the stress-induced motion of small angle boundaries are reported. KINKING was first reported by Orowan1 as a new deformation mechanism. He observed the phenomenon in cadmium single crystals loaded in compression. Glide lamellae in a local region of the rod were observed to snap over suddenly to a tilted position, resulting in a sudden shortening of the specimen. Between the tilted portion and the rest of the crystal there were fairly sharp boundaries, with the slip plane assuming approximately mirror image positions on opposite sides of these boundaries. Orowan considered the boundaries to be regions where dislocations had concentrated. Hess and Barrett' observed the formation of kinks in critically oriented zinc compression specimens. It was found that the sudden snapping over of the tilted region was not an essential part of the kinking phenomenon but rather was associated with the method of loading. Kinking was explained on the basis of the accepted mechanisms of slip and flexural glide. It was also suggested that a kink can be considered as a special type of deformation band. During a recent investigation of the effect of surface condition on creep of zinc single crystals," a similar phenomenon was observed in crystals which were loaded in tension. The specimens were 0.4 in. diam cylindrical rods with a free length of 4 in. between end connections. All of the crystals were tested at a constant load. adjusted to give an extension rate of approximately 0.05 pct per hr. Kinking, as shown in Fig. 1, occurred in some of the tests performed at temperatures above 200°C. Kinking was observed in specimens varying widely in initial orientation, scattering about a 45" angle between the slip plane and the specimen axis. The condition leading to kinking in tension appeared to be non-uniform distribution of flow along the gage length combined with the restraint imposed by the tensile load. At low temperatures and fast strain rates, the distribution of strain throughout the midsection of tension specimens was generally quite uniform; therefore, bend planes developed only near the ends as described by Miller.4 However, at high temperatures under creep conditions it was difficult to obtain specimens in which the distribution of flow was uniform. Some of the factors which may have caused differences in flow stress along the length of the crystals are: Nonuniform distribution of impurities, accidents of growth (lineage structure), slight bending or other damage during handling, surface conditions, and strain-aging characteristics due to dissolved nitrogen." Plastic flow, once started in a local region, often continued to a relatively large strain before other parts of the gage length became active. Under these conditions a series of kinks, such as those in Fig. 1, were produced. Fig. 2 illustrates how a nonuniform distribution of slip produces bending moments which- are responsible for kink formation. If no plastic bending were to occur while the rod extended by pure slip in two separate sections of the rod, it would assume a shape such as that in Fig. 2a. A specimen having this shape and being subjected to a tension load would have concentrations of stress at the concave surfaces C and lower than average stress would exist at the convex surfaces D. Therefore a bending moment is superimposed on the average stress in the regions between C and D. The positions of potential bend planes under these conditions are shown as dotted lines. Actually no such shape as Fig. 2a develops because plastic bending in the region C-D occurs simultaneously with pure slip in the intervening regions. The observed structure of a tension kink is indicated by Fig. 2b. Perhaps the best approach to an understanding of kinking as well as other related plastic bending phenomena, such as the bend planes discussed by Miller,' cell formation studied by Wood et al.,6 and polygonization,7 is consideration of the dislocation model of a bent lattice. Current theories of the slip process postulate generation or multiplication of dislocations at certain lattice imperfections. The mechanism proposed by Frank and Read8 results in continuous generation of concentric dislocation loops which spread out

Jan 1, 1953

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

(Members, are urged -to send in for this column any notes of interest concerning themselves or their fellow-members,). Members and guests R: ho called at Institute headquarters during the period Dec: 10, 1916 to Jan. 10, 1917: F. L. Antisell, Perth Amboy, N. J. William Kelly, Vulcan, Mich. F. J Brulé, Toronto, Ont., Canada. W. H. Lanagan, San Francisco, Cal. Zar T. Crittenden, The. Pas, Mau, Canada. S. Lefevre, Forest Glen, N Y Thomas F. Donnelly, Tucson, Ariz. ' D. A. Lyle, St..David's, Pa. - John Davenport, Brighton, 14 lass. -Domingo Nugués, Buenos Aires, Argon-. E. E. Ellis, Birmingham, Ala. tine. N. H. Emmons, 3d, Copperhill, Tenn. - H. L. Scaife, Clinton, S. C. W.. E. Erdofy, New York, N. Y. Mortimer A. Sears, Washington, D. C. C. L. French, New York, N. Y. E. Spurny, New York, N. Y.' , M. H. Gannon, Butte,. Mont. R. K. Stockwell, Santiago, Chile. R. E. Hoffman, Hannibal, Mo. Benjamin F. Tibby, Salt Lake City, Utah. C. Vey Holman, Rockland, Me. Arthur P. Watt, St. Francois, Mo. Arthur P. Allen has left the employ of the Calumet &- Hecla Mine and is now with the Highland Min. Co., Ashcroft, B. C., Canada. H: C. Bellinger has been appointed. general manager of the Chuqui- - c mata mine-of the Chile Exploration Co. -

Jan 2, 1917