Search Documents

By Louis Jordan

THIS paper presents in an abbreviated form the chief points of interest in an investigation of the tarnish-resistant qualities of silver alloys, an investigation which has been carried out as a joint research by the Bureau of Mines and the Bureau of Standards and will later be reported in detail in an official publication from these bureaus. In 1923 a Commission of Gold and Silver Inquiry was created by a Resolution of the U. S. Senate to study the causes of the depressed condi¬tion of the gold and silver industry. In cooperation with this commission the Bureau of Mines made a preliminary survey to determine in what ways, if any, it might be possible to increase the uses of silver. One of the possibilities indicated by this survey was the development of silver alloys which should be non-tarnishing, or at least less-tarnishing, than the usual sterling silver (copper-silver). The preparation of a rather wide variety of silver alloys and the determination of their behavior under accelerated tarnish tests in the laboratory was therefore undertaken by the bureaus, of Mines and Standards as a joint investigation. PREVIOUS WORK ON TARNISH RESISTING SILVERS At about the time this work was undertaken interest in tarnish-resisting silvers was rather keen due to announcements from England that there had been developed a new silver alloy, "Silanca," which was resistant to tarnish. It was even frequently described in the popular press as "non-tarnishing." A few samples and several analyses of "Silanca" which were available indicated that it was an alloy of sterling fineness, that is, it contained about 93 per cent. of silver, with approximately 4.5 per cent. of antimony and either cadmium or zinc, or both, to make the remaining 2.5 per cent.

Jan 1, 1927

By John D. Hanks

INTRODUCTION Chevron's Uranium Mill is located near Panna Maria, Texas; 70 miles southeast of San Antonio. Designed by Kaiser Engineering, the Mill will process a nominal 2500 dry T.P.D. of uranium bearing ore containing 15% uncombined moisture. Earl Torgerson, San Mateo, California, is the consulting metallurgist on process design. Feed to the plant consists of a mixture of high, medium and low grade sandy day ore; the average grade of the ore will be 0.7% throughout the life of the project. The ore is delivered to the mill via truck and stored by type in individual piles on a flat storage area. The ore is fed by conveyor to a semi-autogenous grinding mill. The SAG mill discharge slurry is pumped either to a storage tank or to the first of five mechanically agitated leach tanks where both H2SO and NaC103 are added. Following leaching, the slurry is mixed with thickener No. 2 overflow before being pumped to a six-thickener, countercurrent decantation circuit where the solution containing uranium is separated from the leach residue. The residue is washed essentially free of solubilized U308 values at the sixth thickener and discharged to an adjacent tailings pond. The first thickener overflow, containing approximately 0.4 grams U308 per liter, is filtered for clarification and sent to the liquid ion exchange (solvent extraction) section. The pregnant aqueous solution is mixed with organic solvent containing amine on which the complex uranyl sulfate ions are absorbed. The immiscible aqueous and organic solutions are mixed and separated in each of the four stages of solvent extraction. The final pregnant organic is directed to a stripping section. A strip solution containing (NH4)2S04 (ammonium sulfate) and NH4C1 (ammonium chloride) is contacted and separated from the organic in each of the four mixer-settler units. The strip solution is mixed with NH3 and the uranium precipitates along with trace amounts of sulfate, chloride, and ammonia. After washing in a thickener, the uranium precipitate or yellowcake is centrifuged and dried in a multiple hearth roaster. Overflow from the yellowcake thickener is recycled back to the stripping section of the solvent extraction circuit. The dried yellowcake concentrate contains more than 98% U308; diluents include H20, ammonia, chloride, etc.. Impurity concentratons in the product are sufficiently low, after drying, to permit direct shipment to refinement installations. ORE RECEIVING Ore from one or more mines will be stored on a pad adjacent to the uranium processing mill. Ore stored in the area may total 200,000 tons or more, which is equivalent to over a two month treatment reserve for the mill. In addition to providing surge capacity, the proposed storage facility permits natural oxidation of the ore and affords an area which, in turn, improve plant U308 recovery and reduces consumption of oxidizing reagents. The uranium bearing ore is segregated at the storage area into several distinct types. One group can be identified by its sandy, clay-like matrix and will be distinguished by its U308 concentration of high, medium, or low. Other ores contain substantial quantities of carbonaceous shale, typical of ore in the area. Feed is recovered from any one or combination of piles, in accordance with operating requirements and recovery factors. The run-of-mine ore, at 15% moisture, is transferred to a stationary, 24-inch by 24-inch grizzly. Undersize material falls into a 280-ton surge hopper located below grade, while oversize material is removed for preliminary size reduction. A sump-pump is located at the reclaim hopper to recover excess mositure and ore spillage for processing. Plant feed is continuously drawn from beneath the hopper at an average rate of 120 tons per hour by means of an apron feeder. The hopper is equipped with a low level safety system to protect the apron feeder assemble. The ore is transferred to a belt conveyor, elevated and discharged into a semi-autogeneous grinding (SAG) mill. Water addition at the discharge point is automatically controlled by a feed rate, moisture analyzer system located on the belt conveyor. GRINDING Minus 24-inch ore, at a rate of 120 mosit tons per hour and cyclone underflow at a rate of 137 moist tons per hour are combined with a controlled 186 gallons per minute fresh, warm plant process water. The mixture, at an average 68% solids, is fed to the SAG mill. The viscous mass is subjected to grinding at a temperature moderately above ambient resulting from use of the 140ºF well water. The 16.5'x5.0' Marcy Mill is driven by a 500 H.P. A.C. Motor. The mill will rotate at 73.4% of critical speed or 14.06 R.P.M. Eight percent of the mill's volume will be occupied by steel grinding balls; 22% by pulp. The mill is designed to rotate in either direction, in order to obtain maximum lifter and liner life. The SAG mill is equipped with a trommel having ½ -inch slots for removal of oversize material at its discharge and the large or oversize material is collected and either recirculated periodically or discarded. The undersize slurry is diluted to 64% solids with the addition of hot well water or mine water to the mill discharge sump. The flow is automatically controlled utilizing data from a gamma density meter. The slurry from the mill discharge sump is pumped to hydrocyclones to classify the particles. Underflow from the cyclones, at 80% + 28 mesh, is recycled to

Jan 1, 1979

By F. F. Poland

S. ROLLE*—As one who has been privileged to read Mr. Poland's paper before its publication, I wish to express high praise for it and the record which it gives of the work done by the Research and Development Department of Revere Copper and Brass Inc. in developing a satisfactory furnace for the recovery of metallic zinc from secondary metals by distillation. I have also had the opportunity of studying the operation of the furnace when running on scrap brass at the Detroit plant of Revere, and I can therefore say from knowledge gained first-hand that the unit is efficient and economical when used in conjunction with distillation. However, when I read what Mr. Poland has to say in reference to the possibility of using the furnace for melting copper cathodes for the production of oxygen-free and tough-pitch copper shapes, I am constrained to be somewhat skeptical. No doubt the furnace can readily be modified so as to make it possible to melt cathodes, but that is only a part of what is required to produce refinery shapes. Because of its construction the atmosphere in the furnace is highly reducing and even without protective gases such as nitrogen the copper cathodes which are

Jan 1, 1950

By D. Harrington

ONE of the main functions of the United States Bureau of Mines is to obtain and disseminate information that will promote safety in and around mines, and the health and safety of employees engaged in mining. Serious health and safety conditions arising out' of contamination of air in metal mines by dust, fumes from explosives and fires, and absorption of oxygen by timber and other causes, led the Bureau of Mines to cooperate with the United States Public Health Service in the study of dust occurrence and ventilation in metal mines in various parts of the country. Dr. A. J. Lanza, of the U. S. Public Health Service, and Edwin Higgins, mining engineer of the U. S. Bureau of Mines, in 1915, made a detailed study in the mines around Joplin, Mo., their reports1 are now available. In 1916, 1917, and 1918, a similar study was made in the Butte, Mont., region by Doctor Lanza and D. Harrington, mining engineer of the Bureau of Mines; the reports of this investigation will be available soon. In 1919, the study was continued in some of the Arizona mines by D. Harrington, of the Bureau of Mines, and G. E. McElroy and Dr. R. A. Koronski, of the U. S. Public Health Service, the underground work being completed in June, 1920; these reports are now being prepared for publication. In the spring of 1920, the scope of the work was extended, with D. Harrington in charge as supervising mining engineer, and short studies made in the mines of the Coeur d' Alenes in Idaho and around Oatman, Ariz. It is hoped soon to extend the work into mines of California, Nevada, Colorado, Michigan, and Minnesota, and ultimately to other states should the mining companies be willing to cooperate.

Jan 2, 1921

By CHARLES F. RAND

PRESIDENT CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N.. Y. FIRST VICE-PRESIDENT BENJAMIN B. THAYER,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER. W. RAYMOND, NEW. YORK; N. Y. SECRETARY BRADLEY- STOUGHTON NEW YORK, N. Y.

Jan 2, 1914

By C. B. Post, G. V. Luerssen

It is generally recognized that non-metallic inclusions in steel come from two principal sources. First are the chemical reactions in the furnace, or in subsequent deoxidation, resulting in slag which does not free itself from the metal. Much information has been published concerning these chemical reactions and their control through proper attention to slag viscosity, composition of deoxidizers, and other qualities. The studies of this subject by C. H. Herty, Jr. and others through the medium of physical chemistry have yielded much information for the steelmaker. The second source is erosion of ladle refractories, such as lining brick, stoppers, nozzles and runners, causing entrapped particles of globules of fluxed silicate material. In contrast with the large amount of information available on the first source, relatively little has been published on the subject of erosion which, in the case of basic electric melted steel, is the principal source of nonmetallics. This is probably due to the fact that the problem was assumed to be one of simple mechanical erosion, which could be solved primarily by modification of ladle practices. Good improvements have been made by elimination of slurries in the ladle, better ladle and runner refractories, and more attention to pouring temperatures. It is doubtful, however, that this problem has been recognized in its true light since it is not one of simple mechanical erosion but rather one of chemical reaction between the metal and the refractories; and in this sense is as much a problem of physical chemistry as the reactions involved in the actual steelmaking process. The influence of ladle refractories on the resulting cleanness of steels was early recognized by A. McCancel who examined large inclusions in steels made by both acid and basic practices. His chemical analyses showed the large influence exerted by the manganese content of the steel on erosion of the ladle and nozzles used in those days. The presence of MnO in such inclusions led McCance to the hypothesis that both basic and acid steels react chemically with the ladle refractories so that small globules of fluxed refractories are carried in the stream into the molds. This early work of McCance was checked by one of the present authors on basic electric bearing-steel, and it was found that on steels containing as low as 0.40 pct manganese the fluxed surface of the ladle lining after delivering such a heat showed as high as 25 pct MnO by actual analysis. Furthermore, by lowering the manganese content of the steel to 0.20 pct, ladle erosion was decreased with a corresponding decrease in silicate inclusions in the steel. Limitations placed on the manganese content for the required inherent properties made it impossible to pursue this line further, and subsequent attention was concentrated on improved ladle refractories, care in keeping the ladle clean and free from loose refractories up to the time of tapping, and pouring the steel at optimum temperature. Our study of the chemical reactions at the metal-brick interface between steel and ladle refractories was revived in 1939 as a result of an experimental observation made on the cleanness of alloy steels of the SAE types. This observation showed that the relative cleanness of such steels made in basic electric arc furnaces of 12 ton capacity and poured in ingots ranging from 1100 to 2200 lb weight was determined to a large extent by the ratio of the manganese and silicon contents, provided other steelmaking variables such as tapping temperature, pouring temperature, pouring time, amount of aluminum added for grain size control, and degree of deoxidation in the furnace were kept reasonably constant. Detailed studies made on the deoxidation and slag practice during the refining period of basic electric furnace practice showed that these two variables exerted some influence on the resulting cleanness of steel in the form of bars and forgings. The important variable, the manganese-silicon balance, was not apparent until heats were made in succession by the best furnace practice kept under fairly rigid metallurgical control. Another observation pertinent to this work concerned the similarity in the microscope of slag particles causing magnaflux or step-down indications in subsequent rolled bars, and the patches of slag frequently seen on the surface of ingots. These patches are generally believed to come from the glassy metal-brick interface in the ladle and represent an entrapment of such glass (both from the ladle brick and nozzle) in the metal as it flows over the refractories in the neighborhood of the nozzle. These glassy particles are carried down into the mold with the liquid steel, and gradually coalesce into a slag "button" which floats on the surface of the steel as it rises in the molds. Periodically the button is washed to the side of the ingot where it is trapped between the surface of the ingot and the mold, later appearing as a slag patch on the surface of the ingot after stripping. Even though most of the small glassy particles coalesce into a slag button while the ingot is being poured, it is logical to suspect this step in the steelmaking process as being a source of slag lines large enough to cause trouble

Jan 1, 1950

By Lewis A. Delano, Harold Rabling

It has been generally recognized that, owing to the extreme friability of galena, fine grinding has a tendency to cause excessive sliming of the mineral, so operators of lead mills have attempted to avoid this condition by commencing concentration at as coarse sizes as any mineral is freed. Jigging has been the basis of the milling process, making a clean coarse concentrate and a large amount of tailing, which was considered sufficiently low-grade to be rejected. However, developments and improvements in concentration processes are everywhere changing the low-grade tailing of yesterday into material worth re-treating today. Investigations of the work of the Hancock jig on the Bonne Terre ore have shown that the best results to be expected will give a tailing assaying 0.75 per cent. lead; the average for all conditions and grades of ore will be between 0.80 and 0.90 per cent. By crushing the jig tailings in ball-mills and retreating by tables and flotation, a tailing of considerably lower grade can be made; the problem then becomes an economic one of increased crushing costs versus higher recovery. In considering the entire elimination of jigging, the increascd smelting charges due to a greater amount of slime galena will be counterbalanced by the lower operating cost, increased recovery, and the many advantages of a simpler flow sheet. In developing these problems in the Bonne Terre mill of the St. Joseph Lead Co., a long series of tests has been carried out covering every stage of crushing and concentration, and a large number of possible flow sheets were considered and tried. Only the final results and a few comparisons will be given here. At the same time, a careful and detailed cost-keeping system has enabled us to compare milling costs with the various Bow sheets, and to calculate the economics of the problem with great accuracy. Concentration Problem The ore occurs as widely scattered deposits of galena disseminated through limestone; it has a specific gravity of 2.8 and the following composition: Pb, 4.00 per cent.; Fe, 3.00 per cent.; Zn, 0.32 per cent.; S, 3.10 per cent.; MnO2, 0.73 per cent.; SiO2, 4.20 per cent.; Al2O3, 3.20 per cent ; CaO, 28.60 per cent.; MgO, 16.85 per cent.; CO2, 36.00 per

Jan 1, 1922

By R. C. Neavel

One of the most important requirements to be met by any coal producer is delivery of size consists tailored to specific applications. Generally these specifications include a minimum as well as a maximum size limit. The customers of a major Indiana coal producer noticed that some shipments of sized coal contained a large proportion of undersize pieces. Also, in these shipments, the pieces which remained within the specified limits were cracked and, when handled, crumbled readily. The producer, certain that these shipments had been properly sized at the tipple, suspected that degradation had occurred in transit. The Indiana Geological Survey was requested to examine the coal from one of these shipments to attempt to determine the cause of breakage. Two basic facts about coal and coal seams led to the employment of petrographic techniques in this investigation. First, all coal seams consist of accumulations of diverse organic and inorganic constituents; and second, most coal breakage, either desirable or undesirable, can be attributed to the inherent weakness of some of these constituents or to poor adhesion between certain constituents. Analyses of degraded coal Sampling: Samples were secured from 2 stock piles of 2-by 4-inch coal in a dealer's yard. The coal in both piles had received the same treatment from mining to storage, although it had been mined and shipped on two different days. The size consist of one pile, however, appeared smaller than that of the other. The sample from the degraded pile is referred to as the slack sample, and the other is called the unslack sample. Size analyses: In order to determine the actual size consist, the samples were screened, with a minimum of rough handling, on square 2-inch, 1-inch, 1/2-inch, and 12-mesh screens. It is assumed that 100 percent of the 2-by 4-inch coal is retained on a 2-inch round screen at the tipple. Analyses of several loads at the tipple indicate that approximately 26 percent of the 2- by 4-inch coal, 100 percent of which was assumed held on a 2-inch round screen, passed through a 2-inch square screen. Twenty-six percent may be taken as the normal difference between round and square screens. Results of the analyses of stockpile coal are shown in Table 1. Cumulative percent versus size are plotted on a Rosin-Rammler chart as Figure 1. Both samples approximately follow normal size distribution; this indicates that breakage is not size preferential and also that the samples are representative of the stockpiles. Although both samples exhibit the same general size distribution, the median size of the slack sample is considerably smaller than that of the unslack sample. Fifty-five percent of the unslack sample was undersize (29 percent greater than the normal 26 percent difference), and 83 percent of the slack sample was undersize (57 percent greater than the normal 26 percent difference). Both piles contained a greater percentage than normal of undersize coal; this indicates that they were both affected by degradation, but to a different degree. Bedding-plane analyses: Coal, because of its laminated nature, will break preferentially along bedding planes, especially where adjacent constituents are poorly cemented to each other. Subsequent breakage perpendicular to the

Jan 1, 1961

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By Frederic Brunton

I. INTRODUCTION THE smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at' very high efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of $1.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 tons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by Alfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Works, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913).

Jan 7, 1915

By John V. Beall

They came from Paris, Washington and Rabat; two directors, two chief geologists and the president of our own local subsidiary company. Such a meeting was not unprecedented, but it seeemed to us that our president was overzealous in arranging for inspections of each exploration site. One was a problem. Jacques, our president, had concocted the idea that we should lead this learned, mature (not exactly aged) group into the desert to see newly found anomaly. It was in virgin country and had been marked by dropping a flour sack on it from the air.

Jan 1, 1971

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By E. F. Loiseau

IN a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it was expected that a plan devised by Dr. Charles M. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust mixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one-half of the lumps produced by the press. The plan was abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is ,usually dry pitch, which is prepared by separating from the tar, at a temperature of 572° Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392° Fahrenheit. But with common tar very weak fuels are obtained, which do not burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By W. Chubb

By measuring the hardness of metals at temperatures just above and just below their allotropic change point, it has been established that crystal structure has a real effect upon the strength of metals. The DPH of cobalt, iron, titanium, uranium, and zirconium have been measured at temperatures up to 1000°C. It was found that the body-centered-cubic crystal structure is always the softer structure when it is involved in an allotropic transformation. The close-packed and more complex structures are inherently harder, and may be expected, therefore, to be better base materials for high strength alloys. IT has been observed that for metals with nearly the same melting point (i.e., tin and lead, magnesium and aluminum) the metal with the more complex crystal structure has a higher tensile strength and hardness. It might be asked whether this effect is really caused by the difference in crystal structure; and, if so, just what is the contribution of crystal structure to the strength of these metals. A qualitative answer to these questions can be obtained by measuring the change in hardness produced by the change in structure in metals exhibiting allotropic forms. The evidence for changes in mechanical properties during allotropic transformations is rather meager. In 1909, Rosenhain and Humfrey' observed that "ß" iron showed much less deformation at the transformation temperature than a iron. By means of a torsion test, Lee found that iron bars were "critically plastic" at the a-7 transformation temperature. Sauerwald and Knehans have shown that the dynamic hardness of iron increases between 900" and 1000°C. In 1930, Albert Sauveur' presented data on the hardness, tensile strength, and torsional strength of pui-e iron up to 1000°C. He concluded, "At 900°C, the a iron transforms into y iron, and this is accompanied by increased strength and stiffness and decreased ductility." The same year, Schischokin" obtained data on the hardness of thallium at temperatures above and below its transformation temperature. His data are replotted on semilogarithmic coordinates as Fig. 1. The fact that his data fall on straight lines in this type of plot is believed to attest to the purity of his metal and the accuracy of his results. In 1941, Nadai and Manjoine" obtained tensile data on pure iron with an indicated increase in strength at about 900°C. These experiments make it quite evident that changes in mechanical properties occur when a metal transforms from one crystal structure to another; but, except for Schischokin's data on thallium, none of the measurements seem accurate enough to determine the relative magnitude of the mechanical property change. Materials The metals that have been examined for changes in hardness during transformation include l—as- deposited commercial electrolytic cobalt about 99.7 pct pure, 2—Armco ingot iron, 3—are-melted iodide titanium of a purity in excess of 99.8 pct, 4—uranium of a purity in excess of 99.5 pct, 5—are-melted iodide zirconium of a purity in excess of 99.8 pct, 6—annealed, 0.08 pct C, rimmed steel, and 7—commercially pure RC55 titanium. While the purity of the first five of these materials leaves something to be desired, it will be noted that the observed hardness discontinuities occurred at the accepted transformation temperatures. (These temperatures are indicated by vertical arrows in Figs. 1 and 3 through 7.) The last two materials are commercial alloys introduced to show the effect of minor alloying elements upon the hot hardness curve. Apparatus Hardnesses at elevated temperatures were determined by means of a vacuum hot hardness machine. A diagram showing the basic features of this machine appears as Fig. 2. This machine is essentially a deadweight hardness .machine in a furnace within a vacuum chamber. The sapphire-tipped indentor

Jan 1, 1956

By John V. Beall

HEAVY-DENSITY separation processes, a commercial application of the sink-float test used in mineralogical laboratories for the separation of mineral particles by their difference in specific gravity, are the biggest development in mineral dressing since flotation, which was at about the same stage of development thirty years ago. The scope of their application has broadened and, though still in the development stage, they are being accepted in a constantly increasing number of commercial installations. This progress in mineral beneficiation is especially satisfying when we realize that our high-grade ore deposits are fast disappearing and a big factor in determining whether a hole in the ground is being sat upon by a liar or an honest citizen is how economically the ore dressers can concentrate comparatively low-grade ores. As early as the middle of the nineteenth century attempts were made to use aqueous salt solutions in a heavy-liquid separation for cleaning coal. But the original and recovery costs of these liquids were high and further, the fact that they were corrosive, unstable, and toxic added to the difficulty in using them.

Jan 1, 1948

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By L. D. Jaffe

From the limited experimental data in the literature, preliminary values were derived for the thermal diffusivity of titanium alloys and for the quenching severity of various mediums used in heat treating them. The thermal diffusivity, under quenching conditions, was found to be approximately 0.006 sq in. per sec. The quenching severity H for brine is approximately 8, for water 4, for oil 0.9, for air 0.08, and for argon 0.02 in. -' The quenching severity of the Jominy-Boegehold end quench water jet against titanium alloys appeared effectively infinite. Using these results, graphs were prepared showing ideal round sizes and Jominy positions having cooled conditions equivalent to those at the center and surface of titanium alloy rounds, plates, and sheets quenched in various media. THE importance of proper quenching of steel parts has long been recognized, and much quantitative work has been done on the subject. Recently, it has become evident that for titanium alloys, too, the rate of cooling from high temperature is important in obtaining high strength and hardness. Maximum hardness and strength may not be attained in the as-quenched condition but rather after a subsequent tempering or aging treatment. Nevertheless, if cooling from temperatures near the ß transus is too slow, for the hardenability of the alloy used, a soft a-ß structure will be produced which will not harden on subsequent aging.'-" The quenching of parts of practical interest can usually be approximated by simple shapes, such as cylinders (rounds) and plates (or sheets) of various thickness and combinations of these. A standard that has been used extensively for comparison purposes is the center of an ideal round: a cylinder quenched in a medium that instantly cools its surface to room temperature." For steel, considerable practical use has been made of the Jominy-Boegehold end quench hardenability specimen,".' and its value for titanium alloys is becoming evident. It therefore appeared worthwhile to attempt comparison of cooling conditions in titanium alloy rounds and plates of various sizes quenched in various media with cooling conditions in ideal round and Jominy quenches. These comparisons are based upon measurements reported in the literature. Quenching Severity of Jominy Water Jet and of Brine As one starting point, there were available the data of Phillips and Tobin8 for positions on a Jominy specimen having the same hardness as the centers of round bars of various size quenched in 5 pct NaOH brine, shown in Table I. The Jominy speci- men is a round bar, normally 1 in. diam and 4 in. long, quenched by a water jet at one end and air cooled on the other surfaces.' After quenching, hardness is measured vs distance from the quenched end on longitudinal flats ground 0.015 to 0.10 in. deep. The data of Table I were based on a subsized specimen of 3/4 in. diam. Since the positions tested are close to the jet quenched end, cooling there may be taken as due solely to the jet, and air cooling can be neglected. These positions are then equivalent to various locations near one surface of an 8 in. plate jet quenched on both sides. Assuming that the thermal diffusivity is constant and that Newton's law of cooling holds, temperature vs time curves at corresponding positions in Jominy specimen and round bar then may be calculated for various assumed quenching severities of the water jet and of the brine. Cooling curves are generally taken to be metallurgically equivalent when they show the same time to reach a temperature halfway between the initial (heat treating) temperature and the final (quenching medium) temperature.5 On this basis, using Russell's tables,9 upplemented by heat flow tables derived in similar fashion by the author for positions near the surface of severely quenched plates, it was found that the experimentally observed equivalence, Table I, was best matched if the quenching severity H of the Jominy water jet was taken as infinite (H = co). This means that the jet quenched surface should be considered as instantly cooled to the temperature of the water

Jan 1, 1956