Search Documents

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550'F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By Rossiter W. Raymond

In the course of this address, President Raymond referred to the law, said to have been discovered at the French works of Terrenoire, that the amount of phosphorus may be increased without injury to steel, if the amount of carbon be proportionately decreased. The works named have been for more than a year, it is said, manufacturing in the open hearth, by the Martin process, steel rails containing as high as 0.35 per cent. of phosphorus, with about 0.15 per cent. of carbon, which were not found inferior to Bessemer rails. It is not claimed by the manager of the works that phosphorus is an ingredient to be preferred, or purposely introduced; but only that materials containing it (such as old iron rails, etc.), can be succesfully employed. Other parties have apparently a higher opinion still of the new manipulation, and are prepared to claim for " phosphorus steel" superior qualities. Mr. I. Lowthian Bell alluded to the subject in his recent address as President of the British Iron and Steel Institute, but without expressing a positive opinion. After pointing out that the commercial value of the process turned on the cheap manufacture of ferro-manganese, by means of which only could the necessary amount of manganese be introduced into the Martin bath, without increasing its contents of carbon, Mr. Raymond proceeded to say that the principle alleged to have been discovered at Terrenoire was already known years ago, in this country, at least. Not only had steel been manufactured here, containing high percentages of phosphorus, coupled with low percentages of carbon, and suitable for use in rails, boiler-plates, etc., but the reason of its surprising qualities had been distinctly surmised, if not widely proclaimed. The following analyses and extracts from private letters prove these assertions. Some of them assert a similar principle in .the case of wrought iron; but the analyses, and the remarks based upon them, have reference solely to the steel manufactured under the superintendence of Mr. Slade, at the works of the New Jersey Steel and Iron Company in Trenton.

By Wm. J. Wright

RECORDS of crude oil in India date back for nearly 100 years, and modest attempts were made to develop the oilfields of Assam about 75 years ago. We have no record of production until 1892 when the fields near Digboi, Assam, yielded about 700 bbl. Since that time, the production of the Digboi fields has increased slowly, but steadily, and new fields have been opened at Badarpur, in Assam, and Khaur, in the Punjab, until the production in India in 1918 was about 293,700 bbl. and the possible production at the present time is approximately 300,000 bbl. per year. In the meantime, the English oil companies in India have been slowly adding to their holdings until they have taken up practically all of the promising territory that is readily accessible, and only about one-tenth of their properties has been touched by the drill. All the producing oilfields of India, and as far as we know all the prospective fields, are confined to areas underlain by rocks of Tertiary age. These rocks consist of more than 20,000 ft. of dark sandstones and shales, with the Nummulitic (Eocene) limestone at the base. In parts of Assam, the lower measures contain economic deposits of bituminous coal. In the Punjab, the upper part contains thick beds of conglomerate. Visible organic remains are rare; except in the limestone and the coal measures. In general, the hardness of the measures increases from top to bottom, but there is an alternation of relatively hard and soft beds throughout the whole series. The rocks are everywhere folded and, in some instances, severely faulted. The crests of eroded anticlines usually stand up as ranges of hills in which the individual ridges are underlain by the relatively' hard beds. Thus structural features are suggested and often clearly defined on the topographic maps.

Jan 3, 1924

By A. V. Deforest, C. W. Macgregor, A. R. Anderson

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By Daryl R. Tweeton, William H. Engelmann, Orin M. Peterson, Jon K. Ahlness, Gregory R. Anderson

The Bureau of Mines measured the geochemical changes as H2SO4 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen,HC03, U. V, Na, K, Ca, Mg,S04, CI, Mo, Mn, Fe, AI, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

AS If see it, then, the engineering advances of which yob have studied here at Golden, the continued growth of. industry that you see about you here in Colorado, and the country-wide progress that I have not time to discuss-these illuminating facts should clear away any doubts as to your future. You have little license to ask, "Where is the call for engineering or what the need? Yankee fashion I might ask you by way of reply, "Have all the mines been opened? Have all the power-houses and transmission lines been built? Have the last improvements in. mill and smelter been in-stalled?" We know that the general answer is No, and the rest of the answer, which tells where are those mines and power plants and what are the new methods and processes in mining and metallurgy, must be sup-plied by you engineers of the future. And anyone who has even casually observed what recent years have brought forth in our profes- sion cannot but envy you your job. Our reconnaissance excur-sion into your future should not be much longer extended, but before turning back there are four landmarks that I would like to point out-not lofty peaks but useful tie points that are worthy of your attention as you traverse the territory of your future work. Two of these are in fact low spots or depressed areas which call for engineering activity; these are commonly called "waste" and "average." The other two are of larger significance and are rather extensive regions in the domain you are to enter and occupy. These larger tracts bear the suggestive place names "fact-finding" and "human engineering" and perhaps will prove to be the heights from which the broadest outlook is to be had in this "pilgrim's progress:" In the first place, waste deserves your attention, al-though I realize that it is possibly the most unpopular word anyone hailing from Washington can publicly utter. Its unpopularity naturally follows from its overuse in the somewhat strong charges made against the industrial and business world some years ago, when the doctrine of conservation was first preached in the land. But waste is a word to be used in an engineering sense as well as for political effect. Properly used, waste is not a word to shy at-rather it is a challenge to the engineer. For example, at present, the loss of 1 kilowatt-hour to every 5 sold is a clarion call to the electrical engineer. Waste is your target to shoot at, the obstacle for you to surmount, the giant for you to slay.

Jan 7, 1928

By J. D. Verhoeven

The effectiue distriblltion coefficient has been Measured in a series of vertical, normal freezing experirtzents with large current densities passing through the solid-liquid interface. The results indicate that the effect of the current on solute redistribution is due to electvotransport in the liquid. The high currents produced extensive mixing in the liquid which was considerably reduced by solidifying in small lubing. Analysis of the convection indicates that it probably vesulls from a horizontal temperature gradient produced by the Joule heating- of the electvic crirver~t. Due to the strong dependence of this convection upon the specimen radius, it is conclnded that only for specit~ens with radii of less than somewhere between 1 and 2 mm wilt electric field freezing be getlerally effec-tire at enhancing the purification of zone-melting experittierats in loe-melting alloys. Experiments on 0.8-mm lubes illustrate some interesting potential applications of this techniqne as a means of solute control on smcrll specimens. In a number of papers published within the last few years'-4 it has been found that passage of large dc currents through the solid-liquid interface of a freezing alloy produces a change in the solute redistribution accompanying the solidification. It had been predicted theoretically by Hucke et al.s and by Pfann and Wagner that such an effect would occur as the result of electrotransport within the liquid boundary layer at the solid-liquid interface. These authors independently derived the following relation between the effective distribution coefficient and the variables of the process: Where k0 is the equilibrium distribution coefficient, V is the mobility of the solute relative to the solvent, E is the electric field intensity, D is the solute diffusion coefficient, R is the rate of interface motion, and 6 is the boundary layer thickness. Both groups of authors show that this equation predicts the possibility of extending the purification ability of zone-melting experiments by the addition of an electric current. However, there are other effects in addition to electro-transport which could be produced by the high dc current and might, perhaps, invalidate the applicability of Eq. [I]. For example, high electric current might affect the interface reaction or perhaps the equilibrium distribution which was assumed to exist at the interface. It was the purpose of this work to determine the applicability of Eq. [I] by systematically investigating a simple system for which all of the necessary parameters were known. It was of particular interest for speculating on the potential usefulness of this technique to determine the maximum practical field intensities obtainable, and the effect of these high fields upon convective mixing in the liquid. The initial work in this study was published in a previous paper3 which will be referred to as I. In that work, a current density of 2000 amps per sq cm was used with specimen diameters of 5 mm. The results gave a qualitative confirmation of Eq. [I.], and also showed that a large amount of convective mixing was produced in the liquid by the current. The present study is an extension of that work to smaller specimen diameters and higher current densities. Two points were overlooked in I and will be emphasized here: a) the value of ko has not been well-established in the Sn-Bi system and b) the observed convection could be due to thermal convection produced from the Joule heating. EVALUATION OF k0 To evaluate Eq. [ I.] it is necessary to know the value of the equilibrium distribution coefficient, k,. Tn I the value of k, was taken as 0.3 from a published phase diagram.7 According to ansen' the best data on the phase boundaries of the Sn-Bi system are those of Davidson.5 The data of Davidson give a k, value ranging from 0.21 to 0.25 for the compositions studied in this work, or an average value of around 0.23. In a recent publication, Rigaud and Tougas'10 determined ko by means of a solidification technique. For an alloy of approximately the same composition as that used in this work they obtained a ko value of 0.39. Hence, there is considerable uncertainty in the value of ko and, consequently, a series of experiments were made to determine k, more accurately.

Jan 1, 1968

By Eugene Coste

ALTHOUGH some of the observers who first paid especial attention to the occurrences of oil and gas in the strata (such as Hunt in 1859, Andrews in 1861, Winchell in 1865, Mendelejeff in 1876, Höfer in 1876, Minshall in 1881, and I. C. White in 1883) seem to have been impressed with the fact that oil and gas deposits were connected with the disturbances in the rocks caused by their upheaval,1 yet, with the exception of Mendelejeff, and possibly Andrews, these observers do not appear to have understood what is really the one essential factor in the occurrence of oil and gas in the strata: viz., the faulting, uplifting, fracturing, fissuring, and jointing always accompanying even slight rock disturbances, and in certain districts (petroliferous provinces)2 allowing solfataric hydrocarbon emanations to force their way up from the interior and to reach and impregnate the porous portions of sediments subjected to the disturbances. Instead of this simple explanation to account for the observed connection between petroleum deposits and rock disturbances, most of the observers mentioned above, and many others who have followed them on the name lines since, have entirely reversed the problem. To them, instead of the dissemination of gases from fissures into the sediments, it presented the accumulation and concentration, according to anticlinal or other geologic structures, of oil and gas originally present throughout the whole mass of the strata where they were produced by the decomposition or distillation of organic remains. Whether this important problem involves accumulation from sources within the oil-bearing strata themselves, or infiltration and dissemination from outside sources, may be easily determined if all preconceived ideas are put aside and the established facts only are considered.

Jan 9, 1914

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By W. D. Haselton, J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte.5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By A. A. Bauer, H. A. Saller, F. A. Rough, J. R. Doig

among uranium alloy systems are the U-Zr, U-Ti,and U-Mo binary systems, in that an intermediate phase, of limited solubility range, exists in each system. These intermediate phase alloys offer a promising field of investigation, both as binary alloys and as ternary alloy combinations. While a limited amount of work has been done on the binary alloys, none has been done on ternary combinations of these alloys. As a possible prelude to more intensive investigation of these systems, a study of the phase relationships between the 6 phases of the U-Zr and U-Ti systems was undertaken. The solid-state portions of the binary constitutional diagrams for the U-Ti,1 Zr-Ti,2 and U-Zr3 systems are shown in Fig. 1. The solid to liquid transformations are not shown, as these transformations were not studied in the ternary system. The phase designations employed are based upon those shown in the uranium constitutional diagrams. The crystal structures of the various phases are given in Table I. Experimental Materials and Methods The ternary section presented is based upon the results of thermal, metallographic, and X-ray analyses of a series of alloys ranging in composition between the phases of the U-Zr and U-Ti systems (U-74 atomic pct Zr to U-35 atomic pct Ti). After preparation of the alloys, thermal data were obtained. On the basis of these data, specimens were heat treated and examined metallographically. Specimens were then selected from those heat treated for X-ray determination of the phases present in what were considered critical phase regions. Alloy and Specimen Preparation—Alloys for this investigation were prepared from selected as-reduced uranium and crystal-bar zirconium and titanium. For nominal compositions, see Table 11. Charges were arc melted from five to seven times under a helium atmosphere, finally being cast into wire-bar form for fabrication. A zirconium getter button was used to clean the furnace atmosphere prior to melting. The alloys were homogenized 20 hr at 900 °C and furnace cooled. A portion of each bar was then removed for thermal analysis; the remainder was saved for fabrication. Alloys 8 through 14 were placed in steel tubes along with zirconium getter chips and, after flushing with argon, the tubes were welded shut and rolled at 1500 °F to a 50 pct reduction in diam. The remaining alloys were annealed 24 hr at ll00°F to insure transformation of the ? phase to the 8-U2Ti phase and were then hot rolled from a salt bath. Attempts to roll alloys 6 and 7 at 1100 °F were unsuccessful. Following this, attempts were made to roll pieces of alloys 1 through 5, which had cracked rather severely during casting, at 1200 °F, but these efforts were also unsuccessful. These alloys were, therefore, further treated in their cast and homogenized condition. All alloys were pickled to remove oxide formed during rolling. Thermal data were obtained on these alloys by conventional differential thermal analysis at a heating rate of 30C per min, and by a high-speed heating method at rates of approximately 10°C per sec. For the latter method of analysis, a 36-gage Chromel-Alumel thermocouple is spot welded between two slivers of alloy, the sandwich being en-

Jan 1, 1958

By H. E. Rorschach

Activity in the oil and gas fields of Oklahoma was more pronounced in 1935 than in 1934, with 2320 completions, an increase of about 21 per cent. The state produced approximately 185,000,000 bbl. in 1935. Osage County and shallow pools in northeastern Oklahoma showed considerable activity. The assembly of a complete table of the oil fields of the state (Table 1) was not achieved, as many of the early records of operators and pipe line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. Increased Field Activities The discovery of large production in the deep Simpson group in the old Fox field in Carter County in the southern part of the state, the discovery of new producing horizons in the Fitts pool, and the extension of Wilcox production in the "Mansion" area at Oklahoma City were the outstanding developments in Oklahoma in 1935. Wildcatting resulted in the discovery of new pools such as Jesse, Hoyt, Grayson, South Keokuk, Wofford, Britton and Stillwater. The Fitts and Edmond pools were rapidly developed during the year. Fox Pool.—Deep production in southern Oklahoma became a reality in October when the Williams No. 1 well of Carter Oil Co. and others, in the Fox pool, began producing oil at the rate of 10,000 bbl. per day from a depth of 8088 ft. After flowing wild several days, the well was killed after pipe stuck and a difficult fishing job resulted. The job had not been completed at the end of the year 1935. This test, considered one of the most important oil discoveries in the Mid-Continent area, opened the entire South Oklahoma area to a deep exploration campaign for Simpson production and production in the Pennsylvanian series on the south flank of the Arbuckle Mountains.

Jan 1, 1936

By H. E. Rorschach

Activity in the oil and gas fields of Oklahoma was more pronounced in 1935 than in 1934, with 2320 completions, an increase of about 21 per cent. The state produced approximately 185,000,000 bbl. in 1935. Osage County and shallow pools in northeastern Oklahoma showed considerable activity. The assembly of a complete table of the oil fields of the state (Table 1) was not achieved, as many of the early records of operators and pipe line companies are not complete, and data for the older fields will perhaps never be fully tabulated. Table 1 includes all of the new fields and most of the important fields of the State of Oklahoma. Increased Field Activities The discovery of large production in the deep Simpson group in the old Fox field in Carter County in the southern part of the state, the discovery of new producing horizons in the Fitts pool, and the extension of Wilcox production in the "Mansion" area at Oklahoma City were the outstanding developments in Oklahoma in 1935. Wildcatting resulted in the discovery of new pools such as Jesse, Hoyt, Grayson, South Keokuk, Wofford, Britton and Stillwater. The Fitts and Edmond pools were rapidly developed during the year. Fox Pool.—Deep production in southern Oklahoma became a reality in October when the Williams No. 1 well of Carter Oil Co. and others, in the Fox pool, began producing oil at the rate of 10,000 bbl. per day from a depth of 8088 ft. After flowing wild several days, the well was killed after pipe stuck and a difficult fishing job resulted. The job had not been completed at the end of the year 1935. This test, considered one of the most important oil discoveries in the Mid-Continent area, opened the entire South Oklahoma area to a deep exploration campaign for Simpson production and production in the Pennsylvanian series on the south flank of the Arbuckle Mountains.

Jan 1, 1936

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years' history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.' The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field's history subsequent to Jan., 1952 (see Fig. 1)'.

By DR. RICHARD RATHBUN

(Washington Meeting, May, 1965.) THE remarks of Dr. Rathbun in his address of welcome render it unnecessary that I dwell either upon the history or aims of the National Museum, and enable me to proceed at once with a brief descriptive outline of the Department for which I am responsible, and this with particular reference to that division devoted to applied geology. The amount of geological material brought together prior to 1876, under the various Congressional acts quoted, was, though valuable, comparatively small. It consisted mainly of the collections made by Professor J. D. Dana and his assistants during the Wilkes Exploring Expedition; by the various geologists accompanying the surveys of the Pacific railroads in 1854-55; the Surveys West of the 100th Meridian under the direction of the Engineering Corps of the Army; the United States geological surveys under direction of Dr. F. V. Hayden ; and the various Land Office surveys. Prior to 1873 there were no paid assistants to care for these collections. They were studied, if studied at all, by " collabrators," so-called, several of whom had offices and even sleeping apartments in the Smithsonian Institution. In the list of these collaborators are found such names as Conrad, Cope, Gabb, Leidy, Lesquereux, Meek, and Newberry. The building now occupied by the National Museum was designed primarily to make room for the great mass of material secured in 1876 at the close of the Centennial Exposition in Philadelphia. As completed in 1880, it afforded opportunity for expansion and incidental organization on much more practical basis than had previously existed. This found expression in the creation of numerous departments with salaried officials to take charge of the various collections. With the appointment of Dr. George W. Hawes to the position of Curator of Geology and Mineralogy, in 1881, and Dr.

Jul 1, 1905

By David White

THE submission of carefully prepared estimates of the oil reserves of the United States calls for no apology or explanation. In this country, petroleum is a rapidly wasting asset and an occasional appraisal of the amount remaining in the ground is a simple business procedure to safe-guard the general welfare and the prosperity of the republic. The rumored danger of failure, in the near future, of the foreign supply on which we depend in constantly increasing amounts makes the immediate review of our available reserves the more imperative. The Director of the U. S. Geological Survey, in March, 1921, requested the American Association of Petroleum Geologists to cooperate in the preparation of new estimates of the oil remaining in the ground. With the members of this cooperative committee, state geologists, regional geologists, consulting specialists, and geologists and engineers attached to many companies worked both independently and through sub-committees. The reports for districts, counties, fields, etc., after review by local or state committees, were discussed by the joint cooperative committee in conferences that, in some instances, were attended by the original compilers of estimates for the states or smaller areas. Finally the data were reviewed and the figures revised by the joint cooperative committee, so that the totals given in Table 1 represent the opinion of the committee, which was composed of F. W. DeWolf, W. E. Wrather, Roswell H. Johnson, Wallace A. Pratt, Alexander W. McCoy, Carl H. Beal, C. T. Lupton, G. C. Matson, K. C. Heald, W. T. Thom, Jr., A. E. Fath, Kirtley F. Mather, R. C. Moore, and David White, chairman.

Jan 6, 1922

By H. M. Morse

This report on oil and gas development in Mississippi covers the period from Jan. I, 1944, to Dec. 31, 1944: Salt Domes During the year six salt domes were drilled for sulphur, but no commercial sulphur deposits were found. One salt dome, the Bruinsburg, in Claiborne County, has produced gas- at 935 to 940 ft' in Moody's Branch marl. The Stringer salt dome in Smith County and the Ruth salt dome in Lincoln County both had a slight showing of heavy oil. Other salt domes have been dry. In addition to the Bruinsburg dome, the Allen salt dome, in Copiah County, and the Richton salt dome, in Perry County, were discovered in 1944; also the Sumrall dome, in Covington County. New Oil Fields Baxtemille Oil Field.—The Baxterville oil field was discoveredby the Gulf Refining Co, in sec. 7, T. I N., R. 16 W., Lamar County. At the end of the year this field had one oil well, with two active operations. Production for 1944 was 1047 bbl. of oil. GwinvilLe Field.—Gwinville field was discovered by S. W. Richardson, in sec. 24, T. 9 N., R. 19 W., Jefferson Davis County. This discovery well was a gas-distillate well, the oil being crystal clear. At the end of 1944 there were two gas wells and one oil well in the field. The oil well is approximately 2 1/2-miles from the gas- distillate wells. Gas production was 55,801 M cu. ft. and the distillate production was 2644 barrels. Heidelberg Oil Field.— The Gulf Refining Co. discovered the Heidelberg field in sec. 30, T. I N., R. 13 E., Jasper County, in January 1944. This field has by far exceeded the other 1943 and 1944 discoveries, having approximately 56 oil wells, 7 dry holes, and 10 active wells at the end of the year. Production to Jan. I, 1945 was 1,441,192 bbl. of oil. Mallalieu Oil Field.—The california Company discovered the Mallalieu oil field in set. 10, T. 7 N., R. 8 E,, Licoln. County. At the end of the year there was one well in the field with three active operations. Production was 32,303 bbl. of oil. Old Oil Fields Brookhaven Oil Field, in Lincoln County, has one oil well, which produced 2590 bbl. of oil during 1944. CarY Oil Field, Sharkey County1 has only one producing well, which produced 11,818 bbl- of oil during the Year- In Cranfield Oil Field, dams County, II oil wells and two gas-distillate wells were drilled in 1944 and there were five active wells on Dee. 31, 1944- The total production for the Year was 5251422 bbl-of oil. The gravity of the oil is 40" to 54.9'- In Eucutta Oil Field1 Wayne County1 34 oil wells were completed during 1944. There were five dry holes and six active wells at the end of the year.. The field produced 454,332 bbl. of all d the average gravity is 25" Flora Oil Field, Madison County, pro-

Jan 1, 1945

The ability of activated charcoal or carbon to adsorb complex metal ions has been recognized for many years, but it wasn't until the late 1940s and early 1950s that attempts were made to employ carbon-In-Pulp or C. I. P. processing to the recovery of gold. Early plants using the process were those at the Golden Cycle in Cripple Creek, Colorado, the Getchell Mine near Golconda, Nevada, and at the Idria Mine in Honduras. Recovery of the carbon from the pulp was done by screening or flotation, and recovery of gold from the carbon was done by burning the carbon (a very difficult task) or by sending it to a smelter. Unfortunately at the time, the price of gold was still fixed at $3-5 per ounce and labor costs were rising to the point where these mines were no longer able to operate. Consequently, C. I. P. treatment was temporarily forgotten. In the early 1970s, however, Homestake Mining Company at Lead, South Dakota, were being forced by environmental regulations to discontinue the use of mercury for amalgamation in their 7,500 ton per day plant, and at the same time were encountering high labor costs in the slime circuit of the plant, where over 2,000 tons of slimes were filtered each day in Merrill plate and frame filter presses. Shortly before that, researchers of the United States Bureau of Mines had developed the caustic -cyanide method of stripping gold from activated carbon and an electrolytic cell (now known as the Zadra cell) to recover gold from the carbon strip liquor. Homestake and the United States Bureau of Mines then jointly operated a C. I. P. pilot plant at Lead. Results were immediately favorable and a 2,400 ton per day C. I. P. plant was then built to treat the slime fraction of the Homestake ore. (See Au and Ag Cyanidation Plant Practice, Volume I, SME of AIME, 1975. Later, Homestake built a second plant at Creede, Colorado, to treat the slime fraction of the tailings from a silver-lead flotation plant. Next was Duval Corporation's 3,000 ton per day C. I. P. plant at Battle Mountain, Nevada. Both of these latter plants are described in this volume. C. I. P. operations under construction at the time of this writing are as follows: Pinson Mining Co. , Nevada Gold Freeport Gold Company, Nevada Gold Compania Minera El Indio, Chile. Silver and Gold

Jan 1, 1981