Search Documents

By Winthrop P. Haynes

The symposium on production for the year 1943 contains few papers on the foreign situation. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. A noteworthy feature of the reports on Texas this year is the map on page 469, which shows the districts covered by the statistics. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author's best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determina-tion. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are suficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on ''Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can be calculated by those interested from the figures given. In classifying wells as to producing methods, enter all wells that are not "flowing" in the column headed "Artificial Lift." If possible, add footnotes to indicate whether the lift is "pumping," "gas lift" or "air lift."

Jan 1, 1944

By Winthrop P. Haynes

The symposium on production for the year 1943 contains few papers on the foreign situation. It has always been the policy of officers in charge of the symposium to refrain from publishing information that might possibly injure national or private interests. At the close of the war we hope again to publish full and accurate records of production abroad. A noteworthy feature of the reports on Texas this year is the map on page 469, which shows the districts covered by the statistics. Excerpts from Circular to Authors In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author's best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determina-tion. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are suficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. Under the columns on ''Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can be calculated by those interested from the figures given. In classifying wells as to producing methods, enter all wells that are not "flowing" in the column headed "Artificial Lift." If possible, add footnotes to indicate whether the lift is "pumping," "gas lift" or "air lift."

Jan 1, 1944

By N. A. Rose, E. L. Spain

THIS study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. INTRODUCTION When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel- exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfulls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. SOURCES AND TYPES OF MATERIALS The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1937

By N. O. Johnson

THE Hog Mountain mine is a pyritic-gold property in the north central part of Tallapoosa County, Alabama, at an elevation of 800 ft. in the southern Appalachian region. It is 13 miles by a good secondary road from Alexander City, a station on the Central of Georgia Railroad. Since its discovery in 1839, the mine has been worked intermittently. The records of past operations are few and are scattered over a long period of time; however, available information indicates a production of approximately 12,000 oz. of gold prior to the present company's activities, which started in 1933. Additional 7844 oz. has been produced under the direction of the present management. The ore from stopes has averaged 0.200 oz. gold per ton; the ore from development, 0.136 oz. gold per ton. Silver, copper, iron and sulphur are also present but to date are of minor importance. The grade of ore in comparatively narrow veins makes necessary extreme vigilance in the methods of mining. Geology Wall Rock.-Hog Mountain consists of a quartz-diorite intrusion approximately 5000 ft. long by 1200 ft. wide. Its resistance to weathering, as compared to the surrounding schists, has led to the formation of a conspicuous ridge rising 400 ft. above the adjacent country. All the mining operations are confined within the limits of this quartz-diorite formation. . Except where there is excessive shearing, either parallel or at flat angles to the quartz veins, all the walls of the stopes within the limits of the veins are strong enough to make timbering unnecessary. Where shearing exists, there may be a sloughing off of the walls, especially in the process of drawing the ore. When this occurs, stulls are placed in the stope, either while the stope is advancing, or while ore is being drawn from a completed stope. In general, very little timber is required. Veins.-The quartz veins have been deposited along fracture planes in the quartz diorite. There are 20 principal veins, all of which are roughly parallel and strike at right angles to the long axis of the formation.

Jan 1, 1937

The Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recommendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush,. .. New Haven, Conn. *Prof. Oscar D. Allen,. .. New Haven, Conn. *C. Constable,.....New York City. *Leven S Goodrich,.... Oxmoor, Jefferson Co., Ala. *Charles J. Nourse,.... Columbia, Lancaster Co., Pa. *J. W. Mickley,.....Hockendauqua, Pa. *Hugh Alex. Crawford,. ..St. Louis, No. *General Ario Pardee,. .. Hazleton, Luzerne Co., Pa. N. W. Lord,.....New Pork City. J. Holme Maghee,.... New York City. *George E. B. Jackson,. .. Portland, Me. *Charles W. Watkis,.... Salt Lake City, Utah. *Charles E. Hall,....Philadelphia. *Charles J. Duval,.... San Francisco, Cal. Joseph Gorlinski,.... Salt Lake City, Utah. * Alfred Wartenweiler,. .. Salt Lake City, Utah. Wilmot J. Bowen,.... Salt Lake City, Utah. *Joseph Stokes,..... Trenton, N. J. Jason P. Brown,.... Boston, Mass. *William Davis Hartshorne,. . Bethlehem, Hunterdon Co., N. J. *Henry Williams,.... Spanish Bar, Clear Creek Co., Cot. *Robert Forsyth ,....Chicago, Ill. *S. T. Wellman,.....Cleveland, Ohio. *H. C. Walton,.....Chicago, 111. *Andrew Roy,.....Columbus, Ohio. *James H. Rittenhonse,. .. Providence, Pa.

THE Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recom¬mendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush, - New Haven, Conn. *Prof. Oscar D. Allen, - New Haven, Conn. *C. Constable, - New York City. *Leven S Goodrich, - Oxmoor, Jefferson Co., Ala. *Charles J. Nourse, - Columbia, Lancaster Co., Pa. *J. W. Mickley, - Hockendauqua, Pa. *Hugh Alex. Crawford, - St. Louis, Mo. *General Ario Pardee, - Hazleton, Luzerne Co., Pa. †N. W. Lord, - New York City. †J. Holme Maghee, - New York City. *George E. B. Jackson, - Portland, Me. *Charles W. Watkis, - Salt Lake City, Utah. *Charles E. Hall, - Philadelphia. *Charles J. Duval, - San Francisco, Cal. †tJoseph Gorlinski, - Salt Lake City, Utah. *Alfred Wartenweiler, - Salt Lake City, Utah. †Wilmot J. Bowen, - Salt Lake City, Utah. *Joseph Stokes, - Trenton, N. J. †Jason P. Brown, - Boston, Mass. *William Davis Hartshorne, - Bethlehem, Hunterdon Co., N. J. *Henry Williams, - Spanish Bar, Clear Creek Co., Col.. *Robert Forsyth, - Chicago, Ill. *S. T. Wellman, - Cleveland, Ohio. *H. C. Walton, - Chicago, Ill. *Andrew Roy, - Columbus, Ohio. *James H. Rittenhouse, - Providence, Pa. * Members. † Associates

Jan 1, 1875

By Robert H. Richards

While yet in correspondence with the heads of the several mining schools for the purpose of bringing the details of my Address into the best form for publication, a severe illness overtook me, and before I had recovered sufficiently to turn my attention to matters of this character the Address had been printed in its imperfect form for volume xv. of our Transactions, and the type had been distributed. The incorporation of the later corrections, in the form of a Supplement, became a necessity. To simplify the corrections as much as possible to the reader, every paragraph which has been revised in any way is here reprinted in full.

Jan 1, 1887

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By F. McIntosh Galbraith

This paper describes the use of the magnetometer, under geological direction, in exploration of the Sudbury nickel district. The writer's experience at Falconbridge has led him to the belief that only through detailed work, and by careful correlation of both geological and geophysical results, can geophysical prospecting methods be applied successfully to mining exploration problems. It is hoped that the basic technique described in the paper will be found to have general application. Introduction Within the past 20 years, geophysical methods of prospecting have become solidly established in the field of petroleum exploration. They have not, however, been similarly adopted by the mining industry, although mining is a far older craft and should be the more advanced in its technique. While, therefore, it is almost a routine matter to have geophysical surveys performed in a new area being tested for oil, a new metal-mining district is usually teeming with prospectors and promoters long before the technical man appears on the scene. Even then, only the more primitive engineering methods are customary in the early stages of exploration. Three factors are chiefly responsible for this situation, The first is the difference between oil pools and ore deposits in their geological modes of occurrence. While most of the known metallic ore bodies have been found outcropping at the surface, petroleum deposits are characteristically buried. This does not mean that all ore deposits outcrop, but neither does it mean that we should rely on "wildcatting" to discover blind ore bodies. The second factor is the relative scale of metallic lodes and accumulations of petroleum. In areal extent, a metal-bearing vein deposit is typically a much smaller geological feature than an oil pool. Presenting a narrower target, it requires closer shooting to score a direct hit. And finally, there is the need, in mining work, for close correlation of the known local geology with geophysical observations. This becomes of increasing importance as the size of the objective diminishes. A geophysical disturbance on a large enough scale will be detected under almost any circumstances and by almost any technique; without benefit of geology, however, the significance of a local anomaly may easily be misread. Campaign at Sudbury In the Sudbury nickel district of Canada, new deposits of nickel and copper have been discovered recently by magnetic methods, under geological supervision. A campaign of exploration, designed to encompass the district eventually, was set in motion in the spring of 1935. After six years, a new and important Ore body has been discovered and its continuity established to 1000 ft. in depth; several areas have been eliminated; and a number of possibilities remain to be tested. This has been accomplished with the expenditure of less than $$I50,000-—including the cost of all diamond drilling. The responsibility for carrying out this campaign was entrusted by the company to its Geological Department, and the under

Jan 1, 1946

By T. J. Woodside

A. E. LEE*—One question of the flue leading to the tube coolers. What gas velocity is maintained to prevent settling of the finely divided fume ? T. J. WOODSIDE (author's reply)— 30 fps. Of course some fume settles out, but is immediately carried away by the screw conveyors. H. R. BIANCO —How effective are the soot blowers ? Do you have to use any hand lancing? T. J. WOODSIDE Only one point, which is right at the top of the economizer and which the soot blowers do not reach, we occasionally hand lance. But everywhere else the soot blowers have been very effective and no hand lancing has been done. L. V. DAVIDSON*—Do you have considerable variation in the lead content of the fume collected if the lead is higher, and is there greater tendency for the fume to stick on the boiler tubes ? T. J. WOODSIDE—There is very little variation in the lead content. From 5 to 7 pct is the widest range variation we have had and we have noticed no difference in the behavior of the fume. C. R. KUZELL—Mr. Woodside has been quite generous with data pertaining to metal and fuel economics. I think he stated that the coal consumption of the furnace was 21/10 21/10 for a pound of zinc recovered. I take it that that is the gross coal input to the furnace. I wonder what the net fuel consumption in terms of coal might be after crediting the fuel equivalent of the waste heat steam recovered? T. J. WOODSIDE—The fuel value of the waste heat steam is approximately 42 pct of the heat input to the furnace. A very large part of the heat, of course, goes out in jacket water—44 pct. A. D. TERRELL*—I would like to know how much lead is in the deleaded material. T. J. WOODSIDE—It is a little less than 2 pct now.

Jan 1, 1950

By A. W. Schlechten, R. P. Abendroth

Jan 1, 1960

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By J. Marshall Downey

The most fortunately situated U. S. potash producer-whether in New Mexico, California, or Utah--once simply took from the ground a mixture of sodium chloride and potassium chloride, crushed it to a maximum of 10 mesh, and separated the two salts by physical methods. He piled the sodium chloride on the desert and sold the potassium chloride to fertilizer mixing companies. Seven companies in the Carlsbad basin of New Mexico now use at least three basic processes for making the separation and at least three more processes have been or are under investigation. In addition, two companies outside the basin use two methods for taking KC1 from natural brines

Jan 12, 1958

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By J. W. Pugh, J. D. Nisbet

THIS study of the ternary has been made as one phase of a metallurgical investigation which began nearly four years ago in the General Electric Company's Research Laboratory in Schenectady, N. Y. The objective of this program is the discovery of new metallurgical information which will lead to the development of better high-temperature materials. Combinations of the four pure base elements—iron, chromium, nickel, and cobalt—are being studied at the present time. It is essential in an investigation such as this to know as much as possible about the constitutional diagrams involved. The study of the iron-chromium-nickel system has been made to this end. Preliminary Explanation of Experimental Procedure: In all, fifty-five alloys at steps of 10 at. pct were made for the investigation of this ternary. Several ternary alloys in the chromium rich corner had to be omitted because their extreme brittleness made testing impractical. All alloys were vacuum melted with hydrogen reduction and centrifugally cast. The apparatus and technique of this process has been described in detail by Nisbet.1,2 The purity of the alloys prepared in this way is considered to be quite good. Impurities are listed as follows: Pct Carbon.............................0.02 Oxygen................................0.02 Nitrogen.........................0.005 Magnesium..................0.03-0.05 Sulphur...........................trace Hydrogen....................trace Phosphorous..................trace Silicon........................ trace After casting, all samples were given a homo-genization treatment which consisted of holding them for 15 hr at 1150°C (2100°F) and water quenching. Testing was begun with the samples in this condition. The tests employed in the study of this system were (1) dilatometer, (2) hardness versus aging temperature, (3) tensile strength and elongation versus temperature, (4) microstructure analysis, and (5) electrical resistance versus temperature. Dilatometer tests were made at the rather rapid heating rate of 1093°C (2000°F) in one hour on a Bristol-Rockwell type instrument. Hardness data were taken on specimens cooled from 204", 427", 649°, 760°, 871°, 982°, and 1093°C under conditions which are thought sufficient to bring the specimens to equilibrium in all but the cases of the very sluggish transformations. Electrical resistance data for several specimens were taken for both heating and cooling conditions in a vacuum furnace especially designed for this work by D. W. Bainbridge, formerly of this laboratory. Provisions were made for heating and cooling standard specimens at a constant rate, while autographic records of resistance and temperature were made simultaneously. Micrographs of all the alloys were made in the quenched condition. Some question may exist as to how such physical values as hardness, tensile strength, and elongation were interpreted to indicate a change in phase. Original data were recorded on physical property versus temperature graphs, each of which was made from the data of a single alloy (fig. la). From these, another series of graphs were plotted with the physical property as a function of composition for constant temperatures (fig. 1b). Sharp deviations in the slope of these composition versus hardness curves often indicate a change in phase. The example of fig. 1 will serve to describe this experimental technique. The plotting of a single point from graph "a" to graph "b," and finally to the phase diagram "c," is illustrated. The location of the point on graph "b" is indicated as point (1). If all the alloys of the A-B binary system were solid solutions at temperature X, the hardness in this curve would be expected to rise at a fairly even rate as A is diluted with B to a maximum at some intermediate value between A and B, as

Jan 1, 1951

By Gerald Sherman

(San Francisco Meeting, September, 1915) THE ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be-discussed here in detail. Certain of their characteristics, however, control -methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattered through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most general characteristics are the softness of the ore and their great horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been .subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread . over a great area. A diagram map (Fig. 1), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 9, 1915

By W. J. Sharwood

(San Francisco Meeting, September, 1915) CUPELLATION is well known to be one of the most effective methods of separating silver and gold from base metals and other impurities, as well as one of the most accurate means for their estimation. In the latter application it consists in absorbing in some porous medium the fused lead. oxide formed by the oxidation of the lead "bath," which carries with it the oxides of other base metals present. It has long been recognized that small amounts of both silver and gold were removed and absorbed together with the base metals, as well as being to some slight extent volatilized, and in work of the highest accuracy a correction is made for the "cupellation loss." Thus. in the assay of bullion this is done by means of "proofs" of like composition, which are manipulated throughout in precisely the same manner as the assay pieces, and are assumed to lose or gain like amounts. In the case of certain very rich ores and commercial products the loss is adjusted by assaying the cupel itself and recovering the precious metal absorbed, but this doubles the labor and does not remedy the loss by volatilization. Arbitrary tables have been drawn up by various authorities with the object of enabling a correction to be applied without the use of a check. These have been of very limited practical use owing to the fact that a number of factors affect the losses sustained. For a fixed amount of precious metal the loss varies with the amount of lead used, with the nature and amount of the impurities, with the porosity of the cupel, with the air supply, and above all with the temperature at which cupellation is carried on. Pure silver loses relatively much more than gold, but the loss in either is diminished by au addition of the other metal. The concentration of precious metal in the litharge increases as the concentration in the lead increases, but little work has been published connecting the two. If all other conditions remain the same the actual total loss increases, but the percentage loss diminishes, with an increase in the weight of precious metal treated.

Jan 8, 1915

By AIME

THE history of the Mine La Motte area covers a greater period of time than any other mining operation west of the Mississippi, for it was almost exactly four centuries ago that the white man first visited the region. In May 1541 a few men from the party of Fernando de Soto traversed the place looking for silver which they understood the Indians had found in the vicinity. Some historians say that De Soto himself visited the place sometime later. No other white man came through again until the early 1700's. In 1712 King Louis XIV of France granted to Antoine Crozat a charter for transacting all business and government in the vast domain of the New Continent stretching from the Gulf of Mexico northward indefinitely. This

Jan 1, 1947

By H. K. Najarian

This paper describes recent development work on the Wheaton-Najarian Vacuum Condenser for Zinc at Josephtown Zinc Smelter, wherein, to dissipate the heat of condensation, the "airlift" action of gases bubbling through the molten zinc in the condenser is utilized to circulate the zinc through an outside "cooling well" and cooling it continuously. AN earlier paper1 gave an account of initial development of the Wheaton-Najarian Vacuum Zinc Condenser at the Josephtown Zinc Smelter of the author's company. This paper is a progress report of further development work over the years directed toward improving the efficiency and increasing the capacity of the condenser. In this type of zinc condenser, zinc vapor with accompanying noncondensable gases from electro-thermic zinc smelting furnaces is passed upwardly through a mass of molten zinc confined in a refractory-lined U-tube. The zinc vapor condenses in the molten zinc and the noncondensable gases are drawn out of the condenser by suction applied over the surface of the molten zinc. The heat of condensation of zinc, amounting roughly to 1000 Btu per lb of zinc condensed, is absorbed by the molten zinc and, in turn, is dissipated continuously to keep the temperature of molten zinc in a range to permit effective condensation. At the time of publication of our first paper, we had at Josephtown Smelter five units of 69-in.-bore metal furnaces and one larger metal furnace having 96-in. bore. Each 69-in. metal furnace had a condenser with 22-ft overall length. The 96-in.-bore furnace had a condenser with overall length of 31 ft. Condensers were of circular cross section, with corrugated steel outer shell and carborundum lining. Diameter of these condensers was 32 in. inside the refractory lining. Molten metal in the con- denser was kept cool by spraying cold water on the outside of the condenser shell. Under good operating conditions, 22-ft condensers produced some 12 tons of metal per day; and the 31-ft condenser, about 22 tons. When the furnaces produced zinc vapor at higher rates, invariably the condenser temperature would rise to levels where excessive blue powder would form and accumulation of accretions in the condenser would be accelerated. We found that, with the system of cooling in use, we had to provide heat-exchange surface of some 150 sq ft to condense 1000 lb of metal per hr with reasonable efficiency. The wall of the condensers was made up of 5/8-in.-thick corrugated-steel shell having next to it several layers of mica and inner refractory lining of special carborundum shapes to fit the corrugation in the steel shell, and having a minimum thickness of about 2 in. Relatively low rate of heat transfer through the thick condenser wall and slow internal circulation of the molten zinc limited the rate of heat exchange between hot metal within the condenser and the cold water flowing over the outer steel shell. The thickness of the condenser wall was about minimum that we considered suitable for continuous operation. As we learned to operate the electrothermic furnaces with higher power input, producing zinc vapor at higher rates, it became apparent that we needed condensers having larger heat-exchange surfaces. Our 96-in.-bore furnace had 6 single-phase power circuits with transformers rated at 500 kva each and normally good for power input of 3000 kw.

Jan 1, 1959