Search Documents

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By M. TAYLOR

AT Grand Saline, some 65 miles east of Dallas, the Morton Salt Co. of Chicago has for some years operated a brine pumping and evaporation plant on a salt dome. They recently drilled trial holes to obtain data on the dome, preparatory to opening, a new mine, with the following results: The dome is in the form of a truncated cone, with an average of 210 ft. of cover. The top of the dome is approximately one mile in diameter, with the town of Grand Saline lying over the northern rim, and the sides slope off at an angle of 50" to 80" from the horizontal. The deepest holes were drilled to 900 ft. without penetrating beyond the salt, and indications are that the salt deposit is several thousand feet thick. As the deposit increases in area with the depth, there is undoubtedly enough salt to supply a mining operation for an almost unlimited period of years.

Jan 1, 1930

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles are correlated with present practice for both the anthracite and the bituminous coal. fields, and meth¬ods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various meth¬ods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment.

Jan 1, 1943

By Philip E. LaMoreaux

Fluoride, generally less than 0.5 ppm, is present in ground water from rocks of Paleozoic age and older, in northern and eastern Alabama. Some of the water-bearing formations in the Coastal Plain area of the State yield water with as much as 6.8 ppm fluoride.

Jan 1, 1950

By C. J. Frosch, J. A. May, H. G. White, C. D. Thurmond

Gallium phosphide epitaxial layers were grown from the vapor phase on undoped single-crystal galliurn arsenide substrates in silica tubes by an open-tube wet-hydrogen process. The epitaxial layers were grown over a range of water pressures at three substrate temperatures. Excess donor concentrations were determined by surface barvier capacitance measurelrzents without removing the layers from the substrates. The excess dmlor concentration, ND-NA, is fo~ind to vary approxilnately inversely with the pressure of water added to the hydrogen carrier gas. This is the relationship that would be expected for singly ionized silicon donors on gallium sites in extrinsic galliunz phosphide, with the silicon coming from the SiO generated by the reaction of hydrogen with the silica tube. An increase in the partial pressure of water in the hydrogen stream decreases the SiO pressure. The results indicate that ni, the intrinsic hole and electrmt concentration for gallium phosphide at the three substrate temperatures, is smaller than the concentration estimated from available data for the density of states effective masses and the energy gap. Mass-spectrographic measurements confirm that the dono?, introduced into gallium phosphide is silicon. The equilibrium concentrations of silicon in vapor-flown gallium Phosphide have been estimated from available thernzodynamic information that includes the solubility measurements of silicon in gallium phosphide in equilibrium with a gallium-rich liquid phase. Satisfactory agreement with the measured silicon concentrations is obtained. FROSCH1 has described an open-tube process for growing single-crystal Gap from the vapor phase by a GazO transport mechanism. The method depends upon the reaction of H20 in an H2 carrier gas with a heated source of polycrystalline Gap which provides the necessary vapor species. When the temperature of these vapor species is lowered, super saturation occurs and single-crystal Gap will deposit on a suitable substrate. Unintentionally doped single crystals of Gap grown by the wet H2 process in silica tubes are n type. Evidence is presented to show that the donor introduced is silicon, and that a qua si-equilibrium model accounts for the inverse dependence of the donor concentration on the water partial pressure and predicts the magnitude of the donor concentrations. Ainslie et al. experimentally showed a similar inverse relationship between the carrier density and oxygen pressure for GaAs. Emission-spectrographic analyses showed a decrease in the silicon concentration with increasing oxygen overpressure for GaAs. Cochran and Foster suggested the theoretical possibility of suppressing silicon contamination by using Ga20 generated by the reaction of gallium with water vapor. 1) EXPERIMENTAL The apparatus and procedures are essentially the same as those described by Frosch.' The apparatus consists of a 25-mm-ID SiO2 tube extending through a controlled high-temperature flat zone for the location of the polycrystalline Gap source and a downstream temperature gradient falling at a rate of about 14°C per cm. The latter provides the region of super saturation for the location of the single-crystal substrate. The partial pressure of water in the inflowing hydrogen stream, pA2, O was controlled by mixing me-tered proportions of dry H2 with H2 saturated with H2O vapor at 0°C. The total gas flows were about 200 cu cm per min in all experiments. The Gap sources were prepared by pulverizing boat-grown polycrystalline ingots to pass a 20-mesh sieve. The substrates were cut from an undoped single-crystal boat-grown GaAs ingot purchased from Monsanto. This ingot had a carrier concentration of about 1015 atoms per cu cm, a resistivity of about 5 ohm-cm, and a mobility of about 5000 sq cm per v sec at 25°C. Substrates with dimensions of 1 by 1 by 5 x lo-' cm were employed. The growth faces were chemically polished (111) arsenic faces. Epitaxial layers, at least 7.5 x 10-3 cm thick, were grown,. This required from 1 to 24 hr depending upon the Pii2Q values and the temperatures. In all of the runs, the source temperatures were 50°C higher than the substrate temperatures. Samples were prepared

Jan 1, 1968

By Nicklaus Heil, L. D. Clark

As political tensions in African and Asian mineral producing regions increase, the orientation of Latin America's economic development assumes importance not only in the U.S. hemispheric policy but also in our mineral-based economy. Latin America as a mineral supply source has been confronted with regional, political and economic problems which may, at best, have limited further investment and, at worst, have suggested possible repudiation of existing investments. Historically, the mining industry has provided a basis for the national economies of Bolivia, Chile and Peru, and recently the governments of these countries have sought to force increased development of the industry through new and somewhat revolutionary mineral legislation. The extent to which the mineral industries are intended to finance economic development is uncertain and the influence of this legislation on economic freedom and incentive for foreign and domestic investment is a matter for some thought. Two facts are outstanding: first, mining, at present, provides approximately 80% of the foreign exchange in Chile and Bolivia and 42% of that in Peru and, second, existing tax revenues are insufficient to finance a developing economy.

Jan 5, 1967

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By John M. Lovejoy

CURRENT production of petroleum on such a vast scale presents many interesting problems- the solutions of which are important not only to those directly interested in the business, but to the nation as a whole. The industry is relatively young. Until the discovers of the Lucas gusher at Spindletop in 1901 petroleum production had not exceeded 60,000,000 bbl. per year compared with 1,100,000,000 bbl. in 1936. In 36 years then, the modern oil business, production, transportation, refining, and marketing has developed. I will first present a brief history. of oil production as a background for consideration of the present situation.

Jan 1, 1937

By Eugene A. Thiers, William V. Morris

INTRODUCTION Direct reduction processes reduce the various commercial forms of iron oxide (pellets, concentrate, fines, etc.) to metallic iron at temperatures lower than that of molten iron. Thus, this technology includes practically, all iron reduction processes other than blast furnaces and electric pig iron furnaces (whose output in terms of world production is negligible). The product of these processes which is known as direct reduced iron (DRI), or sponge iron, is primarily used as a source of metallic iron in steel-making operations. Interest in DRI, which has been significant since the early 1960s, increased significantly in recent years with the rapid growth of DRI installed capacity throughout the world. The importance of the subject for the Circum-Pacific region stems directly from the influence that DRI has on iron ore consumption and on future steel development for this region. Although there is widespread agreement that electric furnaces will continue to increase their share of global steel output, and especially so in the countries of the Pacific Steel community, some doubts exist about future scrap supplies being adequate to support growth at past rates. The authors believe that such doubts are soundly based. As this paper points out, the total supply of all metallics used in electric furnaces may not be adequate to support the extrapolated rapid growth in electric furnace steel production. This paper seeks to provide perspective on the global and Circum-Pacific prospects for DRI in light of recent energy price developments and the current recession. In this regard, the demand for DRI within the context of recent evolutionary patterns in steel-making, the outlook of DRI supply in terms of prevailing production costs, and the prospects of new technology are discussed. THE DEMAND FOR DRI Although several reports published in the last 10 years predict high rates of growth in DRI, the subject remains a controversial one. Significant growth has indeed occurred, but not to the extent anticipated in the studies summarized in Table 1. The substantial difference between previous expectations and present reality can be ascribed primarily to: (1) lower growth in steel production than formerly anticipated; (2) numerous cancellations of DRI facilities that were previously announced; and (3) a fundamental and probably irreversible change in the economics of DRI production. Note that DRI capacity at the end of 1980 was about 16 million tonnes, a significantly lower figure than any of the projections above. In addition, DRI production was only about half of capacity, reflecting the abnormally low rates of capacity utilization in this industry. [ ] Before examining the current outlook in steel, it is pertinent to note that the market for DRI is usually different in the industrialized countries of the West from that in developing countries. In the former, the available infrastructure and industry's diversification extends DRI's potential markets to numerous steelmaking, foundry, and other industrial applications, although competition from scrap and other forms of metallic iron is constant. Scrap is generally available in these countries and, therefore, DRI competes with it in electric furnace steelmaking, basic oxygen steelmaking (as a coolant), cupola foundry operations, or as an additive in the metallic charge for open hearth and blast furnaces. On the other hand, DRI in developing countries is often allocated exclusively to domestic electric furnace steelmaking or, when capacity exceeds domestic captive requirements, to export. Notwithstanding quality considerations, DRI is being and is likely to continue to be used predominantly as a source of metallics in iron and steel-making. Other uses of DRI, such as in copper cementation represent a marginal market in terms of overall tonnage and can be ignored at this point. Therefore, DRI demand is-determined by the overall availability of metallic scrap in its various forms--a function of steel production and its probable evolution. The Global Steel Outlook Given the present recession, an objective appraisal of the long-term outlook for steel is particularly difficult. On the one hand, historical trends and, especially, the inertial forces associated with such a basic industry as steel must be recognized; such trends suggest that the current stagnation with

Jan 1, 1982

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By George Sears

UNTIL a comparatively few years ago, interest in tantalum was limited almost wholly to its scientific investigation, but its extreme resistance to the action of even the strong mineral acids, its great avidity for the common gases, hydrogen, oxygen and nitrogen, and its capacity for transforming alternating to direct current are winning for it a place in our industrial life. Tantalum is not attacked by any single acid except hydrofluoric, nor is it affected by solutions of alkalies. Aqua regia, which readily dissolves both platinum and gold, has no action on it. This resistance to the common corrosive agents is an outstanding property of tantalum and accounts for many of the applications to which it has been put. When heated, tantalum reacts readily with oxygen and nitrogen and absorbs large volumes of hydrogen, 740 volumes being taken up at a dull red heat. This capacity for absorbing gases is being utilized to an increasing extent in the manufacture of vacuum tubes, in which tantalum is used for the metal parts, especially for grid wire. It is said to be a superior metal for this purpose, particularly in power and sending tubes, because of its low secondary emission. The use of tantalum in the manufacture of electrodes, dishes, spatulas and other laboratory apparatus appears to be fairly steady. There has been some development in its use for dental instruments, surgical tools, pen points, hypodermic needles and acidproof pumps. Recently it has been used in the manufacture of spinnerets for the rayon industry, of nozzles for the manufacture of artificial casings for sausages and of lining for plant equipment.

Jan 1, 1930

ENGINEERING department problems of unravel- ling filing systems of reference data, detail drawings, magazine tear sheets, technical records, manufacturers' catalogs-and coordinating them with the information classification systems employed by the company library and other information services -are being solved in many cases by adopting a basic classification system such as that used by Sweet's Catalog Service and applying its classification and indexing methods to file or bookshelf. By this procedure the engineering department does away with the confusion, duplication, and conflict that exist between personal, department, and company library files. It establishes a pattern for regulating and distributing the potential information that piles up daily in the engineering department basket marked "Incoming."

Jan 5, 1954

While coal was undoubtedly seen by the early travellers within the state, the first mention of it was in the late 1820's when hunters put some stones from a creek bed under the logs of a large camp fire, and awoke later to find the stones on fire. The stream was later named Coal Branch; the location was at the eastern side of the present Bibbs County.1 In the Louisville Daily Journal of Feb. 11, 1831, the following short editorial note appeared: "Tuscaloosa Coal.-A small quantity of this article has reached Mobile, and has been tried in the office of the Patriot; it is said to be an excellent article. We invite such of our friends as desire economy in fuel, love a cheerful and constant fire, or would eschew a smoky room, to call and examine." On a geological map published in 1832, the "Carboniferous group" is shown and a spot near Tuscaloosa indicated as showing bituminous coal,2 and this is again alluded to in Morton's Synopsis, 1834. A brief description of the coal fields in the state in 1834 said that in winter coal was brought down the. Black Warrior River to Mobile and sold there at the same price as Liverpool coal, $1.00 to $1.50 per barrel, ($10 to $15 per ton) and that the writer was using it in his laboratory.3 At that time it was in local use by smiths and an iron foundry was using it in Shelby County.4 In 1836 some coal was mined in the Birmingham district, chiefly in the northern portion of the Coosa basin, where it was loaded on barges and taken down the Coosa Rivers.5 "William Whitman dug coal out of Wolf Creek (Walker County) in 1837," and in the same county, in 1839, the first coal shaft in the state, was sunk. This was near the mouth of Lost Creek and was known as Frierson's Shaft. It was operated by a hand windlass, using two tubs.1

Jan 1, 1942

By F. Julius Fohs

As an industry approaches stabilization, greater and greater stress must be laid on its technologic progress, which becomes a prime aid in improving its condition. The oil industry is tending toward this stage and hence its engineers must be pressed into greater service to prevent stabilization and stagnation from becoming synonymous, and to supply, either by improvements in processes or by new machinery, a means of obtaining savings in raw and finished products. Thus profits can be assured warranting continued investment. It may be repeated, technology must apply a slight improvement here, a change there, or a complete renovation, to eliminate inefficiencies and make each dollar invested yield greater results. The profits of ycstcrday were made of rich strikes, of monopolized patents or processes, of control of prices and of markets. Sixty-five years of growth, of large investment, of healthful competition, and of expanding markets, have put the oil industry in the foremost rank of world industries. .Just as the railroads passed a similar period of expansion and growth, and arc being stabilized with reasonable profits, so the oil industry must take advantage of the efforts of its engineers and experts to promote its healthful growth and a better service to the people. Herein is attempted a review of recent progress in which is presented the advances in exploration, production engineering, transportation, refining and greater efficiency in uses of petroleum, with a view not only to stressing important new processes and methods, but also the problems that press for solution. This review can only touch outstanding developments of recent years, but the several Petroleum Division symposiums of our program will present details worthy of attention. Exploration Geology offers directly little new in the technique of oil-finding— major stress being laid on improvement in subsurface correlation by means of foraminifera1 studies, additions to the knowledge of which are being made, slowly but surely, and by means of mineral, and especially heavy mineral, determinations in well samples. The general application

Jan 1, 1927

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By S. D. Baumer, P. M. Hulme

B. M. Larsen (U. S. Steel Co., Kearny, N. J.)—Could we have some sort of an estimate on the cost of calcium carbide for this treatment? Also, if you used calcium carbide on carbon-saturated iron, would some effect hold back the reaction? P. M. Hulme (authors' reply)—As far as I know we have not worked on carbon-saturated iron. About 3½ pct C is the highest we have worked on. As far as cost goes, it depends on how much sulphur You have to take out. It will run anywhere from $0.75 to $2.00 a ton overall cost including the cost of carbide per ton of metal treated. That is, using the efficiencies that we show in this paper. We are getting better efficiencies now. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—Did you say 2 lb of calcium compound? Mr. Hulme—That is based on 10 lb of calcium carbide per lb of sulphur removed. D. E. Babcock (Republic Steel Corp., Youngstown, Ohio)—We have run this type of desulphurization process at the blast furnace. We have desulphurized between 100 and 200 at the blast furnace and taken the iron right out of the furnace with an injector system. The process gave us quite varied results; stratified iron, high sulphur on the top and low sulphur on the bottom, and we decided it was impractical. Mr. Hulme Just what was the type of injection equipment? Dr. Babcock—Nitrogen gas for one injection method and we used fairly large gun equipment. We followed the same general type of pattern you show only on a larger scale. Mr. Hulme—It sounds very much like what we call the gale of wind method. We have very erratic results with that. Dr. Babcock—We have tried several types, and particle sizes. The operation was not satisfactory. Mr. Hulme—Of course, we have never tried it on that scale except on a continuous basis. That is the reason we abandoned the idea of working on 35 ton ladles on a batch principle and took it as it came out of the cupola and treated it on the fly on a continuous basis. Dr. Babcock—When you compare the relative effectiveness of the process as carried out, it does not give a very favorable comparison of that process which is already developed. We did not feel it was worth the

Jan 1, 1952

By G. W. Hodges

The Basic Oxygen Process shop at Gary Works is a three vessel shop tapping 220 ton heats. The larger portion of the heats are teemed into ingot molds with the remaining heats being continuously cast in a single strand continuous slab caster. Ingot production includes a wide range of carbon, alloy, and high-strength steels in many ingot sizes for bar, structural, plate and sheet and tin products. Individual ingot weights vary with the number of ingots per heat ranging from a high of 48 to a low of five. Caster production is primarily Riband, a proprietary low carbon grade for sheet and tin applications developed by United States Steel for continuous casting; some Riband steel is vacuum degassed prior to casting. Maintaining a satisfactory level of ladle performance on both ingot and caster heats with a high production rate and widely varied product mix is a demanding and exacting job requiring the best of equipment, materials, and, most importantly, personnel. The improving trend in ladle performance in the No. 1 BOP shop at Gary is due to a combination of factors, which will be described in the following presentation.

Jan 1, 1972

By W. J. Millard

IT is well known that the excellent mica from Brazil played a most vital role in World War II. Increased production from Brazil was necessary and with the assent of the Brazilian Government engineers from the United States went down to study the problem. One of the means advocated by a former Chief of Metals and Minerals Branch of the Board of Economic Warfare, Mr. Carl Schwegler, was the use of stripping machinery. On a pegmatite dike favorable for stripping, a small number of miners could produce as much mica per day as an underground mine employing many times the same number of men. TYPE OF DEPOSIT FAVORABLE The most favorable type of pegmatite for stripping is that which lies more or less parallel to the surface of the slope of a hill. Pegmatite dikes that cut directly into a hill are not suitable for stripping except where a long outcrop extends along the slope. Then just the outcrop could be stripped to some advantage. The ratio at no time should be greater than I:3; i.e., I cu. m. of pegmatite to 3 cu. m. of waste, unless the pegmatite was extremely rich throughout the dike. THE ECONOMICS OF STRIPPING When a mineral is badly needed to win a war, not too much heed can be paid to costs. The object is to produce rapidly and in quantity. Again, a deposit containing a superior grade of mica may be worked although the pegmatite is more costly to work than another deposit containing a considerably greater amount of poor-grade mica. For example: one deposit may have a little mica that will run II per cent good stain and better when trimmed and contain 2 kg. of crude mica per cubic meter of pegmatite, while another may run 0.2 per cent of good stain and better, and have a mica content of 10 kg. per cubic meter. A number of stripping projects were found in the vicinity of Raul Soares, Minas Gerais. These were sampled in the various old workings by cutting out a cubic meter of pegmatite and saving the usable mica. Because of the proximity to the surface of most stripping projects, about 34 per cent only of the mica is good for trimming. The other 66 per cent is too badly weathered to be of use. In Table I are given data collected on five properties near Raul Soares. In Table I, "value per cubic meter of pegmatite" means the value of the qualified mica obtainable. This does not include the half trimmed and splittings. By "value per cubic meter of matter" is meant the value of the qualified mica per cubic meter of material excavated; i.e. both waste and pegmatite. This is the figure that should he used to determine whether the operation will be profitable or not, as the cost of stripping is about $0.I4 per cubic meter. With new machinery not subject to breakdowns, the cost per cubic meter should be around $0.10 to $0.I5. To this should be

Jan 1, 1946

By G. Hergert

SUMMARY Three gradients have been identified in regard to the average horizontal ground stress increase with depth. [S (0-900 m) = 9.86 MPa + 0.0371 MPa/m SHa (900-2200 m) = 33.41 MPa + 0.0111 MPa/m SHae (extreme)= 12.36 MPa + 0.0586 MPa/m] The extreme stress values are not caused by mining geometry and are of limited extent only. In some cases geological disturbances like faults and rock type boundaries suggest an explanation but in other cases the unusually high stresses cannot be explained readily. It is interesting to note that in the same locations the vertical stress components are very much higher than those derived from overburden weight and that the vertical stress gradient is similar to the gradient obtained from the extreme horizontal stress components. INTRODUCTION Ground stress determinations have been carried out in mines in Ontario and Manitoba, Canada, over more than a decade (Herget, 1980). Most of the sites are located in the Superior and Southern Tectonic Province of the Canadian Shield, which consist of Archaen and Proterozoic rocks comprising volcanics, metamorphosed sediments and granites. The youngest orogenic deformation occurred during the Grenville Orogeny (955 million years ago).

Jan 1, 1982

By Rupert Spivey

Kennecott Copper's Chino mine is one of the oldest copper mines in the United States, having been operated by the Spaniards as early as 1800. At that time haulage methods were indeed primitive. Indians brought the ore up on "chicken ladders" in leather buckets. It was then melted into crude bars and hauled to Chihuahua by mule train. There are still remnants of the old trails near the present pit where the mule hooves cut grooves in solid rock. The mines were worked as underground operations off' and on until open-pit mining was started in 1910 by John Sully and Daniel C. Jackling. Since that time many haulage methods have been used: mule carts, steam and electric trains and finally large haulage trucks, now believed to be the best method for this mine. The general shape of the pit is oval with dimensions of 1% miles by 1% miles. Working benches are 50 ft high, with the bottom bench at 5750 ft and the top at 6450 ft above sea level.

Jan 1, 1964