Search Documents

By Henry Faul

MEASUREMENT of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (I) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quantitative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carnotite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement.

Jan 1, 1947

By J. C. Jr. Vaughan

ALTHOUGH a considerable amount of practical importance attaches to systems involving gases and molten metals, little is known regarding the effects of alloy elements upon the solubility of gases in liquid iron. The solubilities of hydrogen1 and nitrogen2,3 in pure liquid iron are known and it has been shown that small amounts of silicon and aluminum3 exert only a small effect upon the solubility of nitrogen but greatly increase its rate of solution. This paper presents the results of a study of the Solubility Of nitrogen, at pressures approximately one atmosphere, in molten iron containing up to 1.5.5 per cent silicon.

Jan 1, 1939

By Alfred R. Powell

LATE in 1944 a group of petroleum and coal technologists was organized in Wash¬ington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Technical Oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. Since oil-production facilities in Ger¬many and the occupied countries con¬trolled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Industrial Intelligence Com¬mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined, mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A sum¬mary of the more important information gained by this combined British and American mission is presented below. GERMAN OIL PRODUCTION The oil available to Germany, both natural and synthetic, and including pro¬duction from occupied countries, reached a peak in late 1943 and early 1944. Pro¬duction at this time was at the rate of 1,200,000 metric tons per month, equiva¬lent to i00,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, 50 per cent was crude oil from Romania and Hungary, 12 per cent was crude oil from Germany itself, including Austria, 9 per cent com¬prised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of war¬time production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syn¬thetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per cent of the peak quantity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1946

By A. S. Richardson

VENTILATION of the Butte mines has long been a rather difficult problem because of the natural high temperature of the rock. With increase in mining depth, higher rock temperatures have been encoun-tered, and this has caused a constantly growing demand for more effective ventilation measures. During recent years the hazards of dust in mine air have been more clearly recognized, and have necessitated the adoption of dust-prevention methods. To meet these ventilation problems in the mines of the Anaconda Copper Mining Co., a mines ventilation department was organized in 1918, to act under the direction of the general superintendent of mines. At the present time, under normal operating conditions, the force employed includes the ventilation engineer, two chief assistant ventilation engineers and eight assistant ventilation engineers. The activities of the department are, briefly: (1) planning and supervising operation of the general ventilation system; (2) planning and supervising the operation of dust-prevention measures, together, with dust sampling and related microscopic work for the quantitation of the dust samples and determina-tion of particle-size distribution; (3) the design and development of air-conditioning methods to meet present exceptionally severe temperature conditions and in anticipation of future requirements. To a large extent the technical features of the ventilation methods have been described in earlier papers by the author. This paper is written mainly to summarize past accomplishments bearing most closely on health and safety, with a somewhat more detailed account of the dust-prevention measures that have been developed comparatively recently.

Jan 1, 1938

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in. a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a. previous paper.' The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques. The general geo1ogy of the Coeur d'Alene district, including a detailed description of the rock types encountered, has been comprehensively treated by Ransome and Calkins' in their classic paper, and only local background description, therefore, is felt to be appropriate here. The Hercules deposit transects a portion of the trough of a broad south-trending synclinorium which has been greatly complicated by faulting. More locally, it lies within a block of ground bounded on the east; by the O'Neil Gulch fault, a steep north-south overthrust of considerable magnitude, and on the west by a monzonite stock, the outcrop of which is 1/2 mile or more wide and 5 miles long. The country rock is composed of thin to medium-bedded argillites and argillaceous quartz-ites of the Prichard and Burke formations, the oldest members of the Pre-cambrian Belt Series of sediments in the area, believed to be of Algonkian age. The contact between them is a conformable gradation. The argillite is colored gray to tannish-gray and is fine-grained, compact, and generally massive in structure. Under the microscope the unaltered argillite is seen to be composed principally of anhedral quartz and a few feldspar grains which were at one time presumably partly rounded sand grains, but as a result of recrystallization and cementation by silica, the interstices are now almost obliterated and quartz grains show crenulate boundaries. The sizes of these crystals vary from 0.5 mm down to 0.1 mm in greatest dimension. In all specimens sericite comprises 10 to 20 pct of the rock and is present abundantly between most of the grains as flakes or shreds which vary considerably in size. Sometimes they form a fine felt-like mat or aggregate, and sometimes flakes are seen which appear to be good muscovite. In some specimens, separated rhombic-shaped carbonate grains are abundant, and in some instances these have been changed to sericite. Mining operations to date have explored the Hercules vein to a maximum vertical depth of 3600 ft below its outcrop, and along a maximum strike-length of 3600 ft on certain of the lower mine levels. The main orebody is irregular in outline, extending over a variable strike-length of 400 to 1500 ft; and it is intersected by a strong transverse fault that has been traced from the surface to the bottom level. This has been named the Hercules fault, and apart from the vein itself, it is the most prominent structural feature in the mine. There is good evidence that it existed prior to the introduction of ore solutions and may have influenced ore deposition, but it was also the locus of important post-ore displacement and shows a progressive right-handed horizontal component reaching 200 ft on the deeper levels. Its vertical component is not definitely known but may be considerably greater. The fault strikes 20° N to 50° E and dips westerly at angles of 70" to 45", flattening in dip where it crosses the original orebody from east to west between 1000 and 1600 ft below the surface. At about 3000 ft in depth the Hercules fault is joined by a vertical fault of similar strike, and the major post-ore dis-placement below their junction is taken up along this vertical branch of the structure, now called the Mercury fault. Recent work has been concentrated in this vicinity. Another structural feature of special geologic interest, though of little economic importance, is the occurrence of a porphyritic dike in this area. This lies a short distance above the Hercules fault, essentially parallel to it, and is 5 to 15 ft in thickness. It appears at first glance to cut the mineralization, suggesting push-apart relationship, but small stringers of the vein minerals have been observed to penetrate the dike for a matter of inches at several points. The dike is thought to be related to the monzonite intrusion. A vertical longitudinal projection of the mine is shown in Fig. 1, which illustrates most of the features discussed above. The Hercules vein was deposited along the course of a strong, persistent shear zone that now appears as a braided network of gouge seams running through more or less crushed and shattered country rock. It strikes 70° N to 80° W and dips southerly at an average of 75". Barren parts of the structure vary in width from less than 1 ft to more than 15 ft. The width of mineralized segments may be double that. Although the evidence is not conclusive, pre-mineral, normal movement along the zone may be 1000 or 1500 ft. The horizontal component is unknown. Post-ore movement appears to have been

Jan 1, 1954

By Thomas A. Simpson

THE Birmingham red iron ore district in Jeffer-son County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons.' The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production,' and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country. Most of the mining in the Birmingham district is from slope mines along the outcrop of the ore on Red Mountain, such as Red Ore, Muscoda, Spaul- ding, and Sloss. The Pyne and the Shannon are the shaft mines of the area. The Shannon mine of Republic Steel Corp., in the central part of the area under study, is in Shades Valley at the foot of Shades Mountain. The Pyne mine of Woodward Iron Co. is 2 miles east of Readers Gap in Shades Valley. The hydrology problem has become more prevalent as mining in the area has progressed downdip. An extensive exploratory diamond drilling program is necessary to determine areas where water pressures and abnormal flows are excessive. This operation, added to higher pumpage rates, has greatly increased the costs of ore extraction. In November 1952 the U. S. Geological Survey began a detailed study of occurrence and movement of ground water in the iron mining areas of the Birmingham district. The study is a part of a small-scale but nationwide program to develop data that will be of help to the mining industry in solving mine water problems. The area of the study, in the Ridge and Valley province of the Appalachian system, Fig. 1, is a series of alternate ridges and valleys trending northeast. The principal ridges are Red Mountain, altitude about 1000 ft, and Shades Mountain, about 1100 ft. Shades Valley is between these two ridges, and its lowest point is about 480 ft. Shades Moun-

Jan 1, 1956

By Frank G. Miller, Ralph A. Seban

Problems relating to thermal methods of oil recovery have been given increasing attention during the past year. The nature of the physical and chemical processes underlying thermal recovery are not yet well understood. The need for pertinent basic information is recognized generally. One of the processes involved is the transfer of heat by conduction in oil reservoir rocks containing moving reservoir fluids. This technical note deals with heat conduction in a laboratory sand column filled with a moving hydrocarbon and therefore should be contributory to the presently inadequate fund of knowledge on thc over-all subject. In an analysis of the flow of vaporiziny propane through a horizontal column of sand, one of the present author9 demonstrated correspondence between thc measured values of pressure along the length of the column and those predicted by a theory which postulated that the enthalpy of the propane was invariable along the length of the column. This postulate way implied as a deduction from the principle of conservation of energy but the details of the deduction were not given. The specific purpose of this technical note is the presentation of these details both as an adjunct to the earlier analysis and to supply some additional details on the processes involved in this type of flow. Results disclose that rates of heat transfer by conduction, in the direction of fluid motion, generally would be small for systems of the type studied. FUNDARIENrAI. ENERGY EiQUAI-[ON The principle of conservation of energy may be applied to a section of the porous material on the basis that heat transfer, like fluid flow, is possible in the x direction only. Transfer of heat in the y and z di'rections is prevented by suitable insulation or by taking the medium as infinite in directions perpendicular to the x axis. For steady state heat conduction and conditions of steady fluid flow the principle of conservation of energy specifies that any reduction in the enthalpy rate increases the flow of heat in the same proportion. Stated mathematically, dH KA 87 —- = - — - — U) * dx W dx........ Lvhere is the flow of heat in the positive x W dx direction. TEMPERATURE DISTRIBUTION IN DIRECTION OF FLOW The column of sand used in the previoi~sly described research is divisible into three different flow regimes. each of which may be analyzed independently. In the entrance region the liquid approaches the saturation state. A transition region is postulated following the transverse section at which the saturation state of the liquid is attained. In this transition region gas and liquid phases are both envisioned as present, with no vaporization occurring and with fluid movement restricted to the liquid. The upstream end of the exit region is at the transverse section of the column where the fraction of the pore space occupied by gas first becomes great enough for gas flow and where vaporization of the liquid begins. Fig. 1 indicates schematicaHy the thermodynamic processes undergone hv the fluid in the three flow regimes.

Jan 1, 1956

By O. R. Foster

The use in the iron blast-furnace of slags high in magnesia has been generally condemned, not only on the ground that magnesia renders the slag less fusible, but also because it is said to have less power to remove sulphur from the iron. Percy? says the use of dolomite as a flux should obviously he avoided, because magnesia " tends to induce infusibility," but says nothing of its relation to sulphur in the charge. Bell suggests the absorption of SO2, by lime and magnesia in the blast-furnace, but leads the reader to suppose that the really active agent is lime. Howes says: " The greater desulphurizing power of lime than of magne-

Jan 1, 1900

By P. D. I. Honeyman

DURING 1938 many copper companies again felt the economic pinch and smelter operations were often on a reduced basis which some- times resulted in intermittent operations and complete shutdowns. During the last half of the year production was stepped up and smelting operations resumed a more normal appearance. One of the present-day trends in reverberatory sme1ting is definitely toward high-tonnage operations. i\ t the Phelps Dodge Corporation's Douglas plant, the reconstructed 107 by 26- ft. reverberatory furnaces are operated at the rate of 1000 tons of solid charge per day. The arch, all of silica brick; is sufficiently high above the bath to give

Jan 1, 1939

By Thomas E. Wayland

AN isopachous map is one on which lines connect points of equal thickness of a given unit. This type of map is used by the Florida Phosphate Project of the U. S. Geological Survey to represent the economic phosphate deposits known as matrix and the waste material, or overburden, that overlies the matrix. The top of the bed on which the phosphate was deposited is known as the basement and a subsurface contour map of this old buried erosion surface is known as a basement map. Recent experiments have been made in preparing maps that show tonnages and grades of the phosphate content of the matrix.

Jan 11, 1951

By P. Duwez, C. B. Jordan

The phenomenon of the change of volume of pressed powder compacts upon sintering is well known in the field of powder metallurgy. Depending upon the metal or metals involved and the pressure used in forming, a compact may, in the course of time of sintering at a given temperature, expand mono-tonically, contract monotonically, or first show a volume change of one sign followed by a change of the opposite sign. It is clearly desirable to have accurate knowledge of the magnitude and sign of the change in dimensions to be expected in any given case, both from the point of view of direct usefulness in the fabrication of parts by powder metallurgy, and from the longer range viewpoint of elucidating the fundamental mechanism of metallic sintering. The present study was therefore undertaken as a first step in acquiring systematic and reasonably quantitative knowledge of the change in density of metal powder compacts during sintering. For practical reasons, copper was selected as the material to be studied first, and its densification followed as a function of temperature and time of sintering in hydrogen and in vacuum. Experimental Procedure The copper powder used was that designated by the manufacturer (Metals Disintegrating Co., Elizabeth, N. J.) as MD-151. This powder was sifted through Tyler standard screens to separate the fraction having particle size range between 200 mesh and 325 mesh, and this fraction was used in all the subsequent work. Compacts weighing about 10 g were then pressed in a 1 in. diam round die, using a pressure of 20,000 psi throughout. Sintering was carried out in commercially built electric furnaces in which the resistance windings are so disposed as to produce a nearly uniform temperature along the axis of the furnace for a length of about 18 in. centrally located. In order to be able to sinter in a controlled atmosphere, a 2 in. stainless steel tubing was inserted in the furnace. Each end of the tube was cooled by a water jacket about 7 in. long, and closed with a rubber stopper. The hydrogen used for one series of specimens was purified as described in Ref. 1. For the other set, a pressure of about 0.5 mm Hg was maintained during sintering by a Welch Duo-Seal Pump. The specimens were heated on square trays made of stainless steel. In placing specimens in the trays, a thin even layer of powdered aluminum oxide was first sprinkled on the bottom of the tray. A copper guard disk about half the thickness of the specimen was then placed in the tray and covered with a second layer of alumina. The actual specimen was then set on the guard disk, and a final coat of alumina sprinkled over the specimen. This technique was evolved for sintering the specimens in such a way as to reduce the influence of unknown extraneous factors to a minimum. If the specimen is placed directly on the tray and sintered, it is found that the resulting shape is that of a frustum of a cone, rather than a section of a right circular cylinder, since friction with the tray prevents the bottom of the specimen from contracting at the same rate as the top. In the arrangement used in these experiments, the guard disk provided a support which shrank at the same rate as the specimen, and the alumina powder reduced to a minimum friction between guard disk and tray, and between specimen and guard disk. The procedure followed in sintering consisted of bringing the furnace to the required temperature, and then inserting the specimen into the central heated portion of the furnace tube in one of the two atmospheres used. At the end of the heating period, the specimen was cooled by bringing it into a portion of the furnace surrounded by a water jacket. These manipulations were carried out without opening the furnace, by means of rods which were attached to the trays and operated through a sliding seal in the rubber stopper. The progress of densification of the copper compacts was studied at 1300, 1400, 1500, 1600, 1700, and 1800°F. At each of these temperatures, a specimen was allowed to sinter for each of the following time intervals: M, 1, 2, 4, 8, 16, 32, and 64 hr. The thickness and diameter of each specimen were measured with micrometers before and after sintering, and each was weighed on an analytical balance after sintering. Results The techniques described in the preceding section were found to give satisfactory results. The specimens were not detectibly warped after sintering, and were usually of uniform diameter (that is, truly round) to within 0.001 in., a very few showing a variation in diameter of ±0.002 in. All specimens were found to have the same diameter

Jan 1, 1950

By Fred D. DeVaney

MINNESOTA taconites are extremely hard, and fine grinding is required to produce an acceptable concentrate. To reduce grinding costs, waste material is rejected by magnetic separators as soon as it is liberated. Cyclones are now used in all Minnesota taconite plants to close the grinding circuits. Erie Mining Co. installed its first grinding section at Aurora, Minn., in 1948-a 9 ½ x12-ft. mill and a fine grinding section consisting of a 10 ½ x12-ft ball mill in closed circuit with a duplex 60-in. spiral classifier. Concentrates from the magnetic cobbers treating the rod mill discharge passed directly into the classifier; the ball mill discharge was also treated in magnetic separators and the concentrate from these machines also went to the spiral classifier. Both concentrates passed through ac demagnetizing coils. It is axiomatic that for proper classification the material in suspension must be well dispersed, and it follows that magnetic concentrate must be almost completely depolarized if classification is to be successful.

Jan 8, 1957

By AIME AIME

BUSINESS forecasting may be an inexact science, if it is a science at all, but in the opinion of the statisticians of the American Telephone & Telegraph Co. it is a valuable aid to the making of future business plans, whether it be used by a telephone system, a manufacturer whose distribution is country-wide or, one whose trade is confined to certain sections. Whatever the defects of business forecasting may be; the American Telephone & Telegraph Co: has employed it since 1921, not only for charting the probable; course of telephone traffic over long-distance lines, but' to determine the needs for new plant and equipment: caused by shifting tides in business or increases in population or general industrial expansion.

Jan 1, 1929

By E. S. Machlin, Morris Cohen

GRENINGER and Troiano' were the first to establish the fact that the habit planes of mar-tensitic products are usually planes of high indices. In steels containing 0.55 to 1.4 pct C, the habit plane indices are {225}A.* In steels with more than 1.5 pct C and in Fe-Ni alloys, the indices are {259In. The presence of both habits in certain alloy steels has been reported recently." Several investigators"-" have subsequently attempted to provide an understanding of these complex habit relations. Bowles'6 work is the most recent and the most successful. Like Greninger and Troiano, Bowles concluded that the transformation occurs in two steps, the first, a strain (or displacement) that is homogeneous throughout the volume of the martensitic plate, while the second is a strain that is homogeneous only within relatively small portions of the martensitic plate. The first strain yields the measured tilt of the specimen surface, but does not produce the final martensitic structure. This and the correct lattice orientations are achieved by the second strain. Bowles also reasoned that each strain could be described by the motion of a plane of no rotation and no distortion (hereinafter called the invariant plane) in a direction not necessarily contained in the plane.** In applying these considerations to steels with {225}a habits, Bowles found that the habit plane coincided with the invariant plane of the first strain, a result which signified that the atoms move along certain paths during the transformation. Whether this correlation results from the existence of some sort of a plate nucleus6 lying along the invariant plane of the first strain, or whether the invariant plane primarily defines the preferred directions of propagation of the first strain, will be discussed in a later section. There are two obstacles to the general acceptance of Bowles' treatment: 1—it has not been shown that elements of his double-strain analysis are unique, and 2—it is not known whether his treatment applies to transformations yielding the {2591A habit. Unless these two questions are resolved, the correlation between the habit and invariant planes in the {225}A systems might be regarded as coincidental. Experimental Procedure Using a 70 pct Fe-30 pct Ni alloy as an example of a {2591A habit system, preliminary attempts were made to obtain a double-strain solution based on a Nishiyamax** set of orientation relations and on a Greninger-Troianot set, adopting the stereographic technique described by Bowles" who used the Kurd-jumow-Sachstt set in connection with the {225}A habit. These attempts were unsuccessful because the method is essentially one of trial and error and requires either exceedingly good luck or a prior knowledge of the results being sought. Consequently it was decided to measure independently the strain associated with the formation of a martensitic plate as well as the habit-plane indices of the particular plate. By means of matrix algebra, the measured strain was applied to the austenite lattice, whose orientation with respect to the strain was determined, in order to ascertain whether the resultant structure would have the lattice of martensite. This was not found to be the case, and hence it was assumed that the measured strain was the first of two Bowles-type strains, characterized by the motion of an invariant plane. A solution of this displacement was obtained in terms of the invariant-plane indices and the direction of motion of the atoms. Then the second strain

Jan 1, 1952

By S. J. Rothman, J. J. Hines, D. Rokop, R. Bastar

Self-diffusion has been measured along each principal axis of mosaic-structured and relatively perfect a uvaniuln single crystals. The anisotropy reported before,' D[loo] = D[001] » D[010 , has been confirmed. and is shown to represent volume diffusion. Diffusion along the dislocations in the imperfect crystals increases the measured value of D significantly without changingr either the shapes of the penetvation plots or the anisotropy. SINCE a uranium is orthorhombic, the diffusion coefficients along the principal crystallographic axes need not be equal. A previous measurement of self-diffusion in three mosaic-structured a uranium single crystals1 showed that Dil00| =D[001 >>D[010 This result was deduced from penetration plots similar to those in Fig. 1. That is, the plots for diffusion along [loo] and [001] were the straight lines expected from the solution of the diffusion equation for the boundary and initial conditions of the experiment, while the plot for diffusion along [010] was curved so that the part near X = 0 had a much steeper slope than the straight lines did. The observed anisotropy could have been due either to volume diffusion or to diffusion along the very large number of dislocations in such crystals, according to the model proposed by aart.' The authors of Ref. 1 argued that the latter possibility was unlikely, but did not exclude it. To settle the question, a simultaneous measurement of self-diffusion in mosaic-structured and mosaic-free crystals was carried out. This paper reports the results, as well as a measurement of the temperature dependence of self-diffusion in a uranium. EXPERIMENTAL The single crystals of a uranium used in this experiment are listed in Table I, together with other experimental details. '(Mosaic structured" here means crystals grown by solid-state phase change.3 The Laue spots from such crystals spread over about 6 deg of arc, which indicates that the density of dislocations is very large. "Perfect" crystals are ones grown by Fisher's grain-coarsening tehnique; the Laue spots from these are quite sharp,4 which shows that the dislocation density in these crystals is much lower. All of the crystals were made from high-purity uranium; a typical analysis is given in Ref. 1. The actual diffusion directions were within a few degrees of the nominal. The thin layer-sectioning method was used. The experimental techniques were similar to those described in Ref. 1, except the sectioning. Crystals Za, 2b, 2c, 4a, 4b, and 4c were sectioned on a lathe. Crystals 3a, 3b, and 3c were sectioned by grinding on glass plates, with 1 p diamond powder in butyl alcohol as the abrasive. The use of glass plates eliminated the crowning noted in Ref. 1, and the use of butyl alcohol as a lubricant simplified the chemical processing of the sections. Material from the sides of these three crystals was removed by spark machining before sectioning. The sectioning of crystals 4a and 4c was botched. A small cylinder of metal was extruded from the center of crystal 4a while turning off material from the side of the sample. Crystal 4c was misaligned by 2.1 x 10"3 cm because the dial gage jammed during the alignment. Notwithstanding these errors, useful data were still obtained from these crystals. The points

Jan 1, 1967

By Paul C. Ragland, P. Geoffrey Feiss

The Piedmont province of the southern Appalachians is the focus of interest for many exploration geologists. In the past, only those deposits with significant surface exposure were exploited. Thus, few deposits have been found and relatively little exploration has been conducted in recent years. Modern geochemical and geophysical techniques can alleviate this problem of concentrating on exposed ore bodies by allowing us to "look through" the soil and saprolite to detect the presence of significant mineralization at depth. This paper will attempt to evaluate the feasibility and effectiveness of several geochemical exploration techniques in the Piedmont province of Cabarrus and Stanly counties, N.C. The area chosen for study is shown in [Fig. 1], lying almost wholly within the Mt. Pleasant quadrangle, N.C. The area is on the eastern boundary between the Charlotte belt, a zone of plutonic and intermediate grade metamorphic rocks, and the Carolina Slate belt, a series of complexly interbedded volcanic and sedimentary rocks of predominantly low metamorphic grade. The area is considered to be an early Paleozoic active, continental margin. l As is typical of most of the piedmont, outcrop is sparse. [Figure 2] is a sketch map of the general geology of the area under study, showing the Charlotte belt rocks in the northwestern quadrant and slate belt rocks to the east. Within the area are a number of old mines and prospects, the most famous of which are the Furniss and Phoenix mines in Cabarrus County. All are reported to have contained Au and Cu. Ag and Pb were reported from some. A summary of the deposits is given in [Table 1]. Data used in this study are from three Master's theses completed at the University of North Carolina at Chapel Hi11. 3, 5, 6 In separate studies, well waters, 5 B-zone soils,3 and vein and float from the area were sampled and analyzed. Each study concluded separately that geochemical anomalies in the vicinity of the ores justify use of that specific sampling technique in a geochemical exploration program. However, no comparative study of the methods has been made. It is our intention

Jan 1, 1980

By James H. Boettcher

INTRODUCTION A complex interaction of worldwide economic and political forces is increasingly requiring 3 primary participants for the successful development of large natural resource projects in developing countries. They are the host government of the developing country (the "host government"), one or a consortium of international natural resource companies, (the "Resource Company") and one, or more likely, a syndicate of international lenders. The host government typically controls the rights to its country's natural resources and establishes the economic ground rules for their development. However, because of worldwide inflation and the depletion of easily accessible, high-grade resources, the nominal and real capital development and operating costs of projects have been spiraling. Moreover, the depletion of high-grade and mineralogically uncomplicated resources also raises the technical and operating risks associated with resource recovery. Thus, despite increasing political self-consciousness and economic nationalism in developing countries, international resource companies are still often necessary project sponsors since they can provide, among other things, the required technical and management expertise and equity capital. The presence of these factors, and often the addition of worldwide market access in a project, is often critical in determining whether or not the project will be considered creditworthy by international commercial lenders. The international commercial lender is often the critical third party in project development, due in a large part to the ever escalating-costs of project developments relative to the financial resources of many companies and even a growing number of countries. In addition, lenders have other reasons for taking more than a passive interest in all aspects of a project's development. These reasons include the following: 1. Projects are often financially structured such that the primary security for a loan, once completion and performance standards are met, is the cashflow of the project rather than recourse to its sponsors. 2. Lenders, in addition to the "project risk" just described, are frequently asked to assume various elements of "political" risk which nay put them in a sensitive economic position between the host government and international resource firms (This is discussed later). 3. International banks today have large loan portfolios of developing country debt with final maturities ranging from one to fifteen years. The various current projects undertaken are the building blocks of most developing country economies that will hopefully contribute to the long run economic development of a country as well as generate the foreign exchange necessary to repay foreign loans in the future. In this regard it is useful for lenders to realize whether a given project "makes sense" in terms of a country's natural resource endowments and competitive advantages over other countries. The type of framework discussed in this article would help lenders to better make such assessments. In order to facilitate the continued international flow of capital and technology to developing countries and of readily available supplies of raw materials from them, it is important for each of these three parties to increase its awareness of the goals and objectives of the other parties as well as the bargaining process that results in the legal, financial, credit and fiscal structures by which a joint venture project ultimately proceeds. Each of the parties faces increasingly complicated accept/reject decisions when they are faced with difficult choices among. a wide range of alternative structural combinations each of which has different implications for risk and reward to them. Therefore, by increasing the mutual, 3-way awareness of the decision processes of the other parties, it should be possible to: • provide better information and results in the formation of more rational expectations by all parties going into negotiations, • facilitate the project formulation process by allowing parties to focus more clearly on the areas of common interest and conflict, • result more frequently in final structures and agreements that better reflect the economic and political realities associated with a project and thus • result in more creative, innovative agreements that should reduce the need for changes to them and thus promote the kind of long run political stability conducive to attracting capital and further investment.

Jan 1, 1982

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

By W. R. Phibbs

THE blast furnace of the Columbia Steel Corpn., at Ironton; Utah, was put in blast April 30, 1924, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PER CENT. Moisture 3.90 Volatile 39.00 Fixed carbon 51.10 Ash.... 6.00 Sulfur : 1.07 The analysis of the coke is: PER CENT. Volatile 0.55 Fixed carbon :...:.::: :..:.:: 89.70 Ash 9.75 Sulfur 1.05

Jan 1, 1928

By John Gann

THE following investigation constitutes a brief resume of the more important binary magnesium alloys from the standpoint of metallographic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn.

Jan 1, 1928