Search Documents

By H. R. Aldrich

This paper presents some of the results obtained during the field season of 1919 while mapping, in detail, the stratigraphy of the Gogebic Range in Wisconsin. The detailed stratigraphic section for the range was first published, in 1919, by W. 0. Hotchkiss,1 State Gcologist of Wisconsin. The idea of the continuity of the definite succession thus established was the result of underground work in the productive part of the range in Michigan and Wisconsin, where most of the required data also were obtained. The bulk of the range in Wisconsin is heavily covered by drift; in fact, there is but one satisfactorily exposed section across the entire formation, few partial sections, and only scanty outcrops of any size. Evidently mapping of the detailed members of the formation could only be established at a few points; and if from these small areas the .unexposed portions were to be mapped by projection, the only apparent method for projection was straight-line interpolation modified or supported by data from the scanty outcrops and from test workings. It was found that by tracing a magnetic line, the position of which in the formation may be determined from test pits and outcrops, the projection of that member through the drift-covered areas can be accomplished. The magnetic line serves as a datum horizon within the formation to which reference may be made in correlating outcrops and ledge matter thrown from test workings. The foot wall is easily located also, and from the two datum horizons thus available and the known proportional thickness of the several members in the type sections, outcrops and artificially exposed ledges can be correlated by lithological characteristics. As a result, the tracing of magnetic lines became the basis of our work on the stratigraphy and we were able to carry the mapping of detailed members throughout the length of the range. It was found that the magnetic horizon at the base of the Tyler slate was most easily followed by the dip needle; that discontinuity caused by cross-faulting could be established; that folding along the strike could be detected in a repetition

Jan 1, 1922

This brief resume of events, transpiring in Mexico, culled from the daily New York newspapers, since the last Bulletin went to press, does not indicate any degree of improvement in the situation. MEXICAN MINISTER TO FRANCE RECOGNIZED A dispatch from Paris quotes Alberto J. Pani, Mexican Minister to France, as saying lie lead received notification that lie might present his credentials at the French Foreign Office on May 13. This notice came at the moment the Mexican press was announcing his departure for Spain because of inability to present his credentials. MORE REVOLUTIONARY TROUBLES SOUTH AND NORTH Revolutionary outbreaks hulked large in advices from Mexico City at the end of May, says the New York Tribune. General Eznesto Danny, a major, four other officers and forty men, composing a train guard on the Isthmus of Tehuantepec Railroad, were killed recently in an attack by rebels under Felix Diaz's command. The troubles in the south, coupled with the fact that Villa's activities in the north have necessitated sending troops to campaign against him, have reacted in the capital seriously, it is reported. Military guards hi Mexico City have been doubled and machine guns have been placed on the roofs of the National Palace and the Cathedral. STRIKE AND MARTIAL LAW IN MEXICO CITY Advices from Mexico City, according to the Evening Sun, said that virtually every school teacher in the city was out on strike and that recurrent rioting was being put clown by armed trucks manned by Federal soldiers. The strike of the school teachers was clue to the fact that they had not been paid for months, but the direct incitement is said to have been the contrast between their impoverished position and that of Carranza's generals, who are described as rolling in wealth, and who flaunted their opulence on the streets of Mexico, riding about in high powered automobiles with women bedecked with diamonds and other jewelry. The city is said to be virtually under martial law with no immediate prospect. of a subsidence of the bitter feeling against the military caste.

Jan 7, 1919

By J. E. Burke, Y. G. Shiau

SEVERAL attempts have been made to account for the fact that grains in a fully recrystallized metal will coarsen on annealing Two fundamentally different hypotheses have been advanced; with several variations of each. One school considers that the cause of grain growth is the surface energy of the grain boundary The theory of Jeffries1 that grain size and grain size contrast control growth is an example The second school considers the primary cause to be a difference in the lattice energy on either side of the grain boundary The more perfect grains are considered to grow at the expense of their less perfect neighbors, with a decrease in free energy, and a consequent increase in the stability of the system. Burgers2 presents the case for the strain or lattice imperfection theory of grain growth quite completely The latter theory is attractive, since there is no doubt that differences in lattice energy or lattice perfection can cause grain boundary migration A recrystallization nucleus grows for this reason as was beautifully demonstrated by van Arkel and Ploos van Amstel3 Although it is generally stated that grain growth does not precede recrystallization, several workers4,5 have shown that small strains may induce a single crystal in an aggregate to grow, or at least may cause some' grain boundary migration The origin and nature of the imperfections that are considered to be responsible for normal grain growth have never been clearly described, but it is generally agreed that they are a consequence of the difficulty of atomic reorientation in the solid state, and that they do not seriously differ from the type of imperfection that-can be introduced by mechanical deformation An object of the present work was to determine whether the introduction of mechanical deformation would cause grain growth in a specimen which would not otherwise show it under the conditions used It was also planned to determine the effect of such deformation the rate of growth in a specimen which would show - growth in the unstrained condition Recently Maddigan and Blank6 have indicated that slightly strained specimens of alpha brass can undergo considerable growth prior to recrystallization if annealed at low temperatures French7 has reported that at deformations less than 17 pct it is very difficult to detect the beginning of recrystallization in the same material. It was therefore planned to broaden this work to include a complete study of the microscopic behavior of alpha brass under conditions of temperature, time, grain size and deformation such that recrystallization would not occur or would occur to only a small extent EXPERIMENTAL PROCEDURE The brass was prepared by melting cathode copper and commercially pure zinc

Jan 1, 1947

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By M. R. Hatfield, F. J. Vosburgh

IN a recent article,† it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell-to keep it cool enough for safety and comfort and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a carbon tube nominally 2 5/8 in. o.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a 15-kva. transformer operating

Jan 1, 1941

By M. R. Hatfield, F. J. Vosburgh

In a recent article, it was shown that in the blast furnaces in Germany that are lined with carbon blocks no cooling plates are used, and that shower cooling is employed on the hearth and bosh sections. While one of the authors was in Germany he was told that one furnace was being operated without even the shower cooling on the bosh section, though the hearth section was shower-cooled. In discussion of this interesting situation with a number of blast-furnace operators in this country, it was made clearly and promptly evident that shower cooling was very unpopular, probably because of its messiness and its ineffectiveness. Both of the causes for the dislike of shower coolings are reasonable ones. Shower cooling can be and frequently is messy, but the present cooling of blast furnaces leaves much to be desired on that score. Shower cooling is ineffective as compared with plate cooling, so far as its usefulness in keeping the bricks cool enough not to melt or fall to pieces is concerned. However, the introduction of carbon linings changes the situation. No one is concerned with keeping a carbon lining cool, for no temperature in the blast furnace has any effect on carbon, which is just as stable at 3000°F. as it is at 70°F. The only concern is for the shell—to keep it cool enough for safety and comfort— and for that shower cooling is sufficient. Of course, with only the shell to cool, instead of the shell plus all the refractory material, much less water would be required, and the necessity for constant attention to the flow would be lessened, as the hundreds of inlets and outlets would be eliminated. Probably half of the water used in cooling a blast furnace is used for cooling the shaft and tuyeres and the remainder for the bosh and hearth sections. However, in view of the dislike of shower cooling in the United States, and particularly because at least one German blast furnace is operated with no cooling of the bosh section, thought was given to the possibility that a carbon-lined blast furnace might be operated without any cooling of the entire carbon-lined portion. For that reason a series of experiments was performed to determine what might be the temperature of the shell of a blast furnace protected by a carbon lining and operated under varying conditions up to a maximum inside temperature of 3000°F. Experimental Procedure A schematic diagram of the experimental setup is shown in Fig. I and a photograph of the entire assembly in Fig. 2. The heating element was a a tubc nominally 25/8 in. 0.d. by 2 in. i.d. by 30 in., used as a resistor. Power was furnished by a I5-kva. transformer operating

Jan 1, 1942

By Oscar Johnson

WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill.

Jan 6, 1954

By Arvid Holst Mortensen

The rational exploitation of deposits for cement manufacture requires evaluation of the material, the planning of the quarrying and the right choice of quarry machinery. By using a computer for all evaluations and planning work the optimal recovery of material is arrived at and a quarry layout - and machinery is decided upon. The result will be uniform production throughout the lift of the deposits using a rationally chosen quarry equipment.

Jan 1, 1977

By J. S. Marsh

JOSEPH PRIESTLEY prepared oxygen on Aug. 1, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance-as air-has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic- importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 SIGNIFICANCE OF HIGH-TEMPERATURE HEAT The principal 'function of the open-hearth furnace is to supply sufficient, high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy-and heat is energy is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature; which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon l is understood by dioxide and water vapor as reaction

Jan 1, 1948

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By Anthony Folger, Howard R. Lowe, J. F. Dougherty, E. G. Trostel, Joffre Meyer

The status of the natural gas industry in Alberta, Canada, is described with particular reference to the current extent of natural gas reserves and possibilities for additional development. Certain major fields are discussed as representative of the types of gas accumulations within various broad geographical divisions of the provinces. The estimation of the future performance of a gas reservoir is discussed as the basis for an estimate of the future availability of natural gas from presently known reserves. The future availability of the provincial reserves and the estimated future demand for gas within the province are described. INTRODUCTION This paper is a condensation of a detailed study of the natural gas reserves and the future availability of pipeline gas in the province of Alberta as prepared for Trans-Canada Pipe Lines Limited and presented in public hearings at Edmonton and Calgary before the Petroleum and Natural Gas Conservation Board of the Province of Alberta. The study began in October, 1950, and resulted in the preparation of five volumes of data at the expenditure of more than 20,000 man-hours. This paper is designed to afford a broad picture with detail limited to a type example of both natural ga-accumulation and future availability of gas supply. The province of Alberta has an area of 255.285 square miles which, for sake of comparison. is 8,359 square miles smaller than the state of Texas. Natural gas was first discovered in 1883 at the now abandoned Alderson well located some 20 miles southeast of the town of Princess. The first gas in commercial quantities was found at Medicine Hat in 1890. During the last 68 years. 187 localities have been discovered which are capable of gas production, and 73 per cent of these have been found since 1945. Sixty fields currently are producing gas, including 22 non-associated gas accumulations. Location of the oil and gas fields and prospects in the province of Alberta is shown in Fig. 1, together with a list of the localities of measurable gas, Fig. 1A. The estimated total provincial gas reserve as of Jan. 1, 1952, for the 104 fields estimated, is 11.7 trillion cu ft proved and probable, and for the 187 known areas capable of production is in excess of 16 trillion cu ft on a total proved, probable, and possible basis. Five fields (Pincher Creek, Leduc-Woodbend, Viking-Kinsella, Cessford and Medicine Hat) are estimated to have recoverable reserves of more than one trillion cu ft each. A sixth field, Turner Valley, was initially in this group, but its reserves have been depleted substantially. Twenty-four fields, of which the above mentioned six fields are a part, have estimated gas reserves (including the possible category) in excess of 100 billion cu ft. These 24 fields account for 79 per cent of the total provincial reserves. Comparative systemic analyses reflect that 56 per cant of Alberta's gas reserves are contained in sediments of Cretaceous age; 30 per cent in sediments of Mississippian age; 10 per cent in sediments of Devonian age; three per cent in sediments of Triassic age; and the remaining one per cent in Jurassic and Permo-Pennsylvanian sediments. It is expected that the relative importance of the Mississippian, Devonian, and Triassic sediments will be increased as exploration progresses. GENERAL GEOLOGY The western Canada basin comprises the sedimentary area between the Canadian Shield and the Rocky Mountain Front Range, the Arctic Ocean, and the International Boundary. The basin has an approximate area of 765,000 square miles and embraces parts of the provinces of Manitoba. Saskatchewan. Alberta, British Columbia and the Northwest Territories. Generalized columnar sections for the Province of Alberta are shown in Fig. 2. Substantially all of Alberta, except its northeast corner, has sedimentary cover. Sediments of all the geologic systems are represented. except those of Silurian age.

Jan 1, 1952

By Ed L. Reed

INTRODUCTION The most efficient development of a mine plan for in-situ leach (solution) mining must be based upon an understanding and application of the basic hydrologic characteristics of the aquifer containing the mineral values. Similar knowledge of the overlying and underlying aquifers is also required. This paper summarizes the hydrologic properties of a ground water system and describes some of the more important conclusions that can be drawn from a detailed hydrologic study. Basic to an in-situ leach mining operation is the flow of fluids through porous rock from place to place. The degree to which these movements of fluids can be predicted and controlled determines to a large extent the efficiency of the ore recovery operation. HYDROLOGIC CHARACTERISTICS The principal hydrologic characteristics of a porous medium (sand, intercrystalline or vuggy limestone, fractured basalt, etc.) influencing fluid flow are: Porosity Permeability Thickness Transmissivity Storage Coefficient Water Table or Piezometric Surface Hydraulic Gradient Briefly these parameters can be defined as follows: Porosity: the void space in a unit volume of rock. Permeability: the ease with which fluid will flow through a porous medium. Thickness: the height of the formation which contributes flow to a well. Transmissivity the product of permeability and thickness. Storage Coefficient. the volume of water released from the reservoir per unit drop in head. Water Table or Piezometric Surface: the level at which water will stand in a well: the top of the zone of saturation in a gravity aquifer; the height to which water will rise above the confining bed in an artesian system. Hydraulic Gradient the direction and rate of dip of the water table or piezometric surface. A properly designed pumping test will provide numbers for transmissivity, storage coefficient and the water table or piezometric surface. Drilling records or bore hole logs provide aquifer thickness data from which permeability can be calculated. Ground elevations applied to measured depths to water enable one to calculate the direction and rate of dip of the water table or piezometric surface. Porosity can be determined from core analyses or density logs; it can be estimated from grain size distribution curves in sands or sandstones and from, microscopic examination of drill cuttings derived from carbonate aquifers. CHARACTERISTICS OF FLUID FLOW The characteristics of fluid flow that are vital to an understanding of leach mining include: Velocity Direction Flow Path Radius of Influence The velocity of fluid flow is of paramount importance in planning and managing a leach mine operation. Velocity is directly proportional to the permeability and hydraulic gradient and indirectly proportional to the effective porosity The permeability determined from a pumping test is an average value for the interval stressed; therefore, the velocity calculated from data derived from a pumping test represents average conditions. Under actual conditions discrete portions of the aquifer open to the screen may have permeabilities several times as high as the average and minimum permeabilities only a fraction as much. An injection front will be irregular to the extent that the reservoir rocks are heterogeneous An important consideration is the direct relationship of velocity to head. A reservoir which would provide a velocity of 0.05 feet per day under conditions of equilibrium would allow fluid flow of 36 feet per day under typical leaching operations, i.e. 12-foot injection head, 12-foot pumping level and 50 foot five-spot pattern. The direction of fluid flow is also vital both inside and outside the mine area. In the pattern area the direction of flow is determined by the geometry of the well field and can be approximated by mathematical modeling techniques. Outside the well field, the direction of flow is influenced by both natural conditions and the degree to which production and injection volumes are balanced. Flow directions (and velocities) are critical to an understanding of leachate excursions and their control.

Jan 1, 1979

THE subcommittee on Coal Mining, since its appointment, has been engaged in collecting data about subsidences in coal mines in this country, and it now feels that almost all of the available data about occurrences of this sort in bituminous mines has been collected. As most of the bituminous seams are nearly level, the records obtained give the problem in its simplest form, without complications due to the pitch of the seam. Similar data is being compiled for the anthracite regions and it is hoped that this will be ready for the 1927 meeting. Copies of the questionnaire, Appendix A, were mailed to all of the coal operators' associations, to most of the large operating companies and to many engineers, with the request that any data on the subject be returned to the committee, or that advice of any subsidences known be given. The replies to most of the questionnaires were general only, although some specific cases were given. Many of the companies were unable to reply to all questions, as they lacked the necessary data, but in nearly every case where accurate data was available, it was cheerfully furnished, and any additional information requested was secured. All specific cases of subsidence were followed up by correspondence, and in several cases by personal inspection. Figs. 1 to 31 were made from the information furnished. Table 1 gives measurements of elevations taken in one case at intervals from October, 1913, to May, 1918. With one exception, where the evidence cannot yet be released on account of a lawsuit, it is believed that the cases submitted with this report include practically all that have happened in bituminous coal mining in this country of which actual measurements were secured. Some of these have already been published in the excellent report by Young and Stoek,1 and some instances have been secured from other publications. In collecting these data, the subcommittee had the Engineering Societies Library extend the bibliography given in the bulletin mentioned above to date. This list is given in Appendix B.

Jan 2, 1926

By J. B. Davis

This paper has been prepared at the suggestion of Mr. Dunbar D. Scott, to supplement his " Evolution of Mine-Surveying Instruments."† Before entering into a detailed history of solar instruments, a few remarks will be made touching upon land-surveys in general, and on what has led to the development of these instruments.The oxidation of metals melted in contact with air takes place with dissimilar results. Tin, lead or zinc are examples of a class, the oxides of which float on the surface of the melted metal. First a film is produced, which covers the surface; then, if agitation from any cause exposes new metal to the action of the air, additional oxidation takes place, and the film is increased in volume. This change goes on until a considerable quantity of oxide (or " dross," as it is technically called) is formed; depending, of course, upon the duration of the exposure of the metal to the atmosphere. When such metals are poured, the dross may be skimmed off; and clean metal will be left underneath. The removal of such oxides is, therefore, merely a mechanical process. In the case of copper, however, the result is quite different. The sub-oxide of copper (Cu2O) is readily soluble in molten copper; and therefore, instead of the formation of a film of oxide, to be finally removed as dross, the surface of the metal remains bright and clear, because the oxide has been dissolved as soon as it was produced. It is customary in the process of copper-refining to leave a small quantity of oxide in the metal, in order to oxidize any traces of bismuth, arsenic or antimony which have not been entirely removed. As a result, these metals exist in the commercial product as oxides, and not as metals, which would form an

Jan 1, 1901

By Richard R. Klimpel

The role of dispersion is described in the wet grinding of ores using tumbling media mills and the flotation of coal, sulfide, and non-sulfide ores. Emphasis is placed on characterizing the effects of dispersion in laboratory tests using engineering models which provide information useful for the improvement and control of existing plant operations. Significant economic gains in the above named operations have been realized using these models as guides for full- scale plant testing.

Jan 1, 1980

By G. C. Gester

With the exception of exploration geological work that is being prosecuted in various parts of the mainland of Arabia, the only new developments in Arabia during 1934 were on Bahrein Island, which is in the southwestern portion of the Persian Gulf, approximately 25 miles from the mainland of Arabia. Here the Standard Oil Co. of California, through its wholly owned subsidiary, The Bahrein Petroleum Co., Limited, has continued to carry on a systematic drilling campaign and has constructed camps, pipe line and marine loading facilities. During 1934 eight wells have been completed at depths ranging from 2058 to 2253 ft. These wells have shown average initial productions ranging from 1500 to 5000 bbl., with one, No. 15, estimated as being capable of flowing as much as 11,000 bbl. per day. The oil is asphaltic in character and has a gravity range of from 32' to 34' A.P.I. The locating of all new wells has followed a plan of orderly development, with the ultimate object of obtaining efficiency of operation and maximum production. The wells are taking a penetration of 200 to 250 ft. of the lower or so-called Main productive zone. The upper oil zone, which is cased off, includes 300 to 400 ft. of alternating limestones, clays and shales and carries a heavier oil under lower pressures. The Main zone is similar lithologically to the upper zone. Micro-fauna collected from cores have shown that the oil occurs in formations of lower Eocene and Cretaceous age. Development to date has not progressed sufficiently so that either the maximum thickness of the oil-bearing horizons or the limits of the field can be determined. Something over 10,000 acres has been proven to date. Among other developments leading toward the marketing of oil from Bahrein during 1934 was the construction of a marine loading terminal. This included the laying of over 3 miles of 12-in. submarine pipe line from the small island of Sitra out into the harbor, terminating in 50 ft. of water; also the laying of more than 10 miles of gathering lines from the producing area to the terminal. Three crude oil working tanks with floating roofs were erected on Sitra Island, having a capacity of 250,000 bbl. A pumping plant was provided having a capacity of 5700 bbl. of oil per hour. This is housed in a dustproof building, as rather severe

Jan 1, 1935

By M. H. Merriss

IN THE last few years, there have been developed at the plant of the Nichols Copper Co., Laurel Hill, Borough of Queens, New York City, improvements in electrolytic copper refining by the series system that have materially increased the flexibility and economy of that system. The purpose of this paper is to discuss, as of interest to refiners and to those who have copper to refine, as well as to the engineering profession in general, the changes that have taken place resulting in wider application and increased efficiency of the series system. Copper is electrolytically refined in two ways, which are spoken of as the "multiple system" and the "series system." In both systems, the electrolytic tanks are in series electrically. In the multiple system the electrodes in a single tank are in multiple or in parallel, thus: In the series system, the electrodes in a single tank are in series, thus: There are two important adaptations of the series process, one represented by the series electrolytic tank room at the Baltimore Copper, Smelting & Rolling Co., Baltimore, Md., and the other by that of the Nichols Copper Co.'s plant. At Baltimore, the anode is rolled to perfect

Jan 6, 1925

By Auguste J. Rossi

As is well known, practically all the phosphorus of the ironores smelted in the blast-furnace passes into the pig-metal, increasing its fluidity, but diminishing its strength to such an extent that, if phosphorus exceeds a certain amount, the metal is only fit for fine castings, not required to resist strains, and it cannot be used for the ordinary purposes of good foundry-iron. No phosphorus being eliminated in the acid Bessemer process, the quantity admissible in pig-metal destined for that process must be very small, and hence the ores smelted must be strictly Bessemer ores, of which, in many districts, the supply is taxed to the utmost. On the other hand, very highly phosphoric pig, a metal of little or no value by itself, when refined by the Thomas-Gilchrist process in the basic converter, furnishes an excellent steel; but such pig-iron must be made from ores particularly high in phosphorus; and these ores are not everywhere abundant, and are much sought after for this special purpose. But there are many iron-ores containing a moderate, though still important, amount of phosphorus, which yield a pig-metal

Jan 1, 1897

By J. S. Marsh

Joseph Priestley prepared oxygen on Aug. I, 1774, and noted with great surprise "that a candle burned in this air with a remarkable brilliant flame." On Aug. 2, 1774, some ironmaker possibly began to wonder if this substance could be used to increase his rate of production; at any rate, there is no disputing the fact that the notion of using oxygen for steelmaking in concentrations greater than that available in great abundance—as air—has been in existence for years. Action was delayed by the lack of enough oxygen at a cost within reach of the steelmaker. Within the last several years enough has been available to permit large-scale tests of its use for both combustion, with which this paper is concerned, and for decarburization. The literature is now enormous and easily available; it is sufficient here to cite three items of historic importance in that all are about 25 years old and in that all are remarkably consistent as far as they go, with what is known today.1,2,3 Significance of High-temperature Heat The principal function of the open-hearth furnace is to supply sufficient high-temperature heat to melt the charge and then to increase its temperature to a range suitable for tapping, ordinarily in the neighborhood of 2900°F. That heat is required to make steel is understood by everybody; however, there seems to be some confusion now and then about the significance of high-temperature heat. Transfer of energy—and heat is energy— is always from a point of higher potential to a point of lower potential and, other things being equal, the greater the potential difference, the greater is the rate of transfer of energy. In the open hearth the flame, of course, is the high-potential source. Perhaps the most satisfactory approach is through the notion of theoretical flame temperature, which is the ratio of heat input to the heat content of the combustion products,* the former is composed mainly of heat of combustion of the fuel plus sensible heat of the fuel plus sensible heat of the combustion air. Thus, flame temperature can be increased by increasing the value of the numerator, by decreasing the value of the denominator, or both. The first method is as old as the open-hearth process and, of course, makes use of preheated air; its possibilities have been by no means exhausted. The second method can be put into effect only by changing the composition of the combustion air, since the combustion of a given quantity of fuel produces a definite quantity of product, and since the denominator includes the non-reactive fraction of the air, principally nitrogen. In other words, the denominator consists of the volume of exit gas multiplied by its heat capacity and that volume consists of carbon dioxide and water vapor as reaction

Jan 1, 1949