Search Documents

By E. H. Crabtree

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed

Jan 1, 1950

By Joseph Jenson

Total United States production for 1928 was 900,364,000 bbl. as compared with 901,129,000 for 1927, or 2,466,000 bbl. per day versus 2,468,000. The three major producing areas were Texas, Oklahoma and California. Texas production increased from 217,389,000 bbl. in 1927 to 256,888,000 in 1928—an increase of 39,499,000 bbl. following an increase of 44,500,000 bbl. in 1927. Oklahoma production amounted to 249,558,000 bbl. in 1928 as compared with 277,775,000 bbl. in 1927 and 177,650,000 bbl. in 1926. California production for 1928 was 231,982,000 bbl. as compared with 231,196,000 in 1927. Production increased markedly in Venezuela and declined in Mexico. Elsewhere no great changes or declines in production were noted. New discoveries occurred in nearly all districts. The many excellent reviews of the various districts of the United States presented at this meeting, are each fully summarized and tell their own story so well that little would be gained by attempting to repeat their content here. There are certain impressions to be gathered from these papers and certain trends that are indicated by them which may better be pointed out. OVERPRODUCTION Overproduction is the most serious one of them. Efforts to avert it resulted in a measure of cooperation in the oil industry more widespread in character and more beneficial in results than has ever been recorded in any previous year. These efforts were undertaken in the closing months of 1927 and enthusiastically effected before the spring of 1928 had passed. Unfortunately, slight advances in prices during the summer months accompanied by the letting down of this sort, of effort resulted in a marked increase of production during the latter half of 1928. Successful delay in the drilling of new prospective areas was in effect in Oklahoma. California delayed some drilling and increased its shut-in

Jan 1, 1929

By N. A. D. Parlee, I. D. Shah

ThIS reports on some work done on the solubility and diffusivity of oxygen in liquid silver. Solubility. Improvements in the measurement of the solubility of oxygen in silver and silver alloys were made because precise data were needed for calculating diffusion coefficients of oxygen in these alloys. The apparatus and the procedure used were similar to those of Parlee and Sacris.' The main improvement was in the temperature-measuring technique. A MV30 mullite protection tube containing a calibrated Pt-Pt, 10 pct Rh thermocouple was inserted in the reaction tube from the top through a vacuum-tight swage-lok fitting. The protection tube was well-immersed in the liquid silver, which was heated by induction. A Leeds and Northrup potentiometer was used in connection with the thermocouple. All runs reported were made at 1 atm. The temperature range investigated varied from 940" to 1200°C. The ternary point in Ag-0 phase diagram2 is at 939°C and 0.32 wt pct O. This point was reinvestigated using the above-described apparatus and was found to be at 939°C and 0.315 wt pct 0. It was determined by observing the sudden evolution of oxygen at this point while the solubility measurements were made. The point was easily reproducible if precautions were taken to keep the liquid silver essentially in equilibrium with oxygen and to lower the temperature very slowly. All of the results of this new solubility investigation are plotted in Fig. 1. They are represented by the "least-squares" line shown in the figure and the following equation for solubility at po2 = 1 atm: log% O =695.4/T - 1.086 This equation differs only slightly from that proposed by Parlee and sacrisl and that of Diaz, Masson, and Richardson.3 The points of Parlee and Sacris, using an optical pyrometer, are shown for comparison.

Jan 1, 1968

By M. H. Caron

D. C. Ralston—The fact that none of the organizations that have worked on these ammoniacal leaching processes have contributed discussion of Mr. Caron's papers today is a matter of some disappointment. Adaptations, modifications and improvements have been made by several organizations or individuals and to complete the record I want to document a number of them. The Nicaro Nickel Co. operated a Government owned plant at Nicaro, Oriente, Cuba, during the past war. A report on the project was written for Reconstruction Finance Corp. and is in the document file collected by the Office of Technical Services, Commerce Department and filed with the Library of Congress, where it can be consulted or bibliofilm or photostat copies obtained by asking for copies of PB 97271. Nicaro Nickel Co. has obtained a series of U.S. Patents, my list (probably incomplete) of which bears the following numbers: 2,400,098; 2,400,114; 2,400,115; 2,400,461; 2,400,612; 2,458,902 and 2,473,795. International Nickel Co. has also studied the problem and U.S. Patent 2,478,942 shows that some of the complications involving occasional low extractions have been unraveled. Forward, Samis, and Kudryk, of the University of British Columbia, have also published a study of copper-nickel sulphide concentrate.' Others are interested and it is evident that this type of hydrometallurgy is likely to find a happy application in the not-too-far distant future. Caron's two papers practically amount to a summation of his life's work on the important subject of nickeliferous iron ores and the American Institute of Mining and Metallurgical Engineers is fortunate to have been chosen the medium of publication. M. Rey—The ammonia leaching process has been the subject of certain studies in New Caledonia, but at the present time, the conditions are not very favorable to its adoption. The process is a combination of a thermal and a hydrometallurgical process. As a result, the first costs and the operative costs are rather high. To counteract this unfavorable situation, it would be necessary to make a very high extraction. But unfortunately, the process is delicate and in spite of all of Caron's valuable work, there are still many unknown factors. It is difficult to obtain regularly a high extraction, exceeding 75 to 80 pct. It would be interesting to have the opinion of Inter-national Nickel on the process and to know what the Dutch are doing in Celebes. M. H. Caron (author's reply)—I am quite familiar with the different types of nickel and cobalt ores as found on New Caledonia, and it may be pointed out that the Celebes ores are quite the same in their properties. Their behavior when treating the ores by the ammonia-leaching process is also alike and in my opinion, there is no reason why a high extraction of the New Caledonian ores could not be obtained if the process is properly applied. For the sake of completeness I may add that one of my patents has not been discussed in the papers. This patent deals particularly with the treatment of serpentine nickel ores. (Netherlands No. 62693 40a, French No. 965.786 April 21. 1948. and Cuban No. 13.625 Jan. 1950.) O F. A. Forward, C. S. Samis, and V. Kudryk: Trans. Canadian Institute of Mining and Metallurgy. (1948) 151 (Bull. 434) 350-355.

Jan 1, 1951

By Donald F. Irwin

Amid the violent economic changes of recent years that have affected Canadian gold-mining operations so deeply, the discovery and early developments of Kirkland Lake might easily be overlooked. There was more than one "false dawn" for the district before developments finally established the fact of a superb mineralized zone extending through the present operating properties. Never far from the railway, Kirkland Lake has had the benefit of direct rail service for many years. The pioneer discovery on which the first mill and cyanide plant was erected was the "Tough-Oakes," this property being on what is now the eastern end of the producing area; some time later, the "Lake Shore" was discovered at the present center of the district, and a small plant was built upon it also. Both of these early treatment plants were of pre-war design. Progress in gold metallurgy has caused a gradual change in cyanide practice since the early days at Kirkland Lake, which may be observed in the various plants now operating there. From the beginning, it was recognized that Kirkland Lake ores were more responsive to cyanidation than to alternative recovery methods, and that their mineralization contained gold in very finely divided form. Although sulfides and tellurides are present, the quantity is small, being in the order of 1 or 2 per cent by weight, so that gravity concentration is undesirable, since gold is not confined to the sulfides. Some complication is offered by the presence of tellurides, which have caused lengthy controversy over their importance in recovery methods, but which are now generally regarded as less harmful in the light of increasingly high recoveries being obtained. Nevertheless, finely divided gold intimately associated with sulfides in the presence of tellurides; and occurring in the hard Kirkland Lake porphyry ore, substantially free from natural slime-forming constituents, indicates fine grinding. This has been the universal practice although the degree of grinding has varied a little among the different mills and is considerably finer now than formerly. The natural condition as outlined caused the establishment of fine grinding at an early stage in the development of Kirkland Lake, during the period of valuation of gold at, $20.67 per ounce. With the arrival

Jan 1, 1935

By D. S. Kingery, D. W. Mitchell

Experience in Europe indicates that the control of dust production and dissemination by water or foam systems is not successful except during undercutting. Cybulski, Dawes, and DeBraaf-respectively Director, Mines Research Establishment "Barbara", Katowice, Poland; Principal Scientific Officer, Safety in Mines Research Establishment, Sheffield, England: and Chief, Central Mines Research Establishment, Hoensbroek, Treebeek, The Netherlands-believe that wetted dust becomes readily dispersible and abatement measures should be considered only as a temporary means for reducing the health hazard. In an effort to reduce the health hazard, calcium chloride is used on the floor of main haulageways in Dutch mines and water infusion is practiced in Germany in mines where the coal is relatively porous. With respect to wet coal dust, the Belgians, British, Dutch, French, and Russians reportedly have accepted the results of research from the Polish and American experimental mines on the effectiveness of water as an inert in arresting explosion propagation. The Polish use the two test methods proposed by the U.S. Bureau of Mines for evaluation of the adequacy of wetness of mine dust; they require that water be added to the wet dust to maintain a minimum of 50% moisture by weight if dependence is placed on water alone.

Jan 7, 1964

By J. E. 214-000-000-010 Warren, M. R. J. Wyllie, T. Meidav, L. Scharon, R. Uhley, A. J. deWitte

By considering the stoichiometry of the underground combustion process, an equrztion was derived relating the point velocity of the combustion front as a function of the air flux, fuel content, efficiency' of oxygen uitilization, hydrogen:carbon ratio, and ratio of carbon dioxide In carbon monoxide produced. In addition, an equation for cnlcrllating the amount of injected air necessary 10 produce the oil from I Cu. ft of reservoir space was derived. This equation has a direct bearing on evaluating compression costs for the process. Values calculated from these equations are in good agreement with experimentnlly obscrvcd values obtained from laborator) tube runs reported in the literature. The equations are also u\eful for atlcrlyzinf: experinlental data for inconsistencie.r.. I NTRODUCTION The injection of energy in the form of heat into an oil-bearing formation as a means of increasing the recovery of oil has been the subject of much discussion and experimentation as far back as 1920. The ideas have ranged from the injection of steam to the direct use of electricity as a means of getting thermal energy into a formation. However, most laboratory and field studies have been confined to the process whereby a portion of the crude in the reservoir is burned to generate the necessary heat to increase the mobility of the oil by reducing its viscosity. A recent paper by W. L. Martin, et al.', described the results of a number of laboratory experiments in which the combustion process was studied in a sandpack. Studies such as this indicate that with the temperatures involved, the oil is partially coked in this process and it is this coke which provides the fuel for combustion. The combustion of this residual coke can be analyzed theoretically by applying simple stoich-iometric principles to the combustion process. It is the purpose of this paper to compare the results reported in these experiments with those obtained from theoretical considerations. The variables studied by Martin, et al, among others, include combustion front velocity, air flux, oxygen utilization, fuel concentration, ratio of carbon dioxide and carbon monoxide in combustion gases, and the hydrogen:carbon ratio of the residual fuel. All these variables come into consideration when the stoichiometry of the combustion process is studied. The experimental conditions and results are tabulated in Tables 3 and 4 of Ref. 1. For purposes of comparison with calculated results, it was necessary to change the units of a number of the variables. UNDERGROUND COMBUSTION STOICHIOMETRY The combustion or oxidation of the carbonaceous residue or "coke" on the sand can be described in terms of the equation: where n is atomic ratio of hydrogen to carbon, m is ratio of moles of CO2 to CO produced, and CH. is taken as the unit molecular weight, realizing that actually the coke has a large range of high molecular weights. Assuming that all the fuel laid down in the sand is burned, the ratio of moles of oxygen consumed to moles of coke can be written as follows. Moles 0MolesMolescoke In terms of moles O2 per pound of coke, where 12 + n is the molecular weight in pounds per mole. If the 0, consumed is measured in standard cubic feet (60°F and 1 atm) and the coke in pounds per cubic foot of formation, 2, then:

By W. C. Winegard, J. E. Gruzleski

The stages in the development of cells in the Sn-Cd eutectic have been studied by unidirectionally solidifying specimens under known conditions of growth rate, temperature gradient, and impurity concentration. By means of a quenching technique, the shape of the solid-liquid interface during solidification could be observed. Cells are shown to develop from defects or depressions which exist on the solid-liquid interface of even a pure eutectic. Th,e container wall, grain boundaries , and fault lines in the micro structure play an important role in cell development. A two-phase eutectic dendrite found at high impurity concentrations is described. L HE cellular or colony structure formed during eutectic solidification caused much confusion among early workers in their attempts to classify eutectic structure, and a major advance in our understanding of eutectic solidification was made when the colony structure was identified with a cellular interface caused by the presence of impurity elements.1'2 To date, however, no detailed investigation of the stages in cell development in eutectics has appeared, and little work has been done on the cell morphology. The present paper presents the results of such an investigation. EXPERIMENTAL The Sn-Cd eutectic was used in this investigation with lead as the impurity element to promote cell formation. Materials of 99.999 pct purity were zone-refined to an approximate purity of 99.9999 pct. Alloys as close as possible to the eutectic composition, 67.75 wt pct Sn, were prepared using zone-refined tin and cadmium. The alloys were then zone-melted to the exact eutectic composition, as described by Yue and Clark,3 using a total of twenty to twenty-five passes on each eutectic bar. Only those portions of the bars which contained no primary phases were used in subsequent experiments. Master ternary alloys were prepared by melting together the required amounts of lead and the Sn-Cd eutectic in a sealed Pyrex tube under argon, and these alloys were then diluted with pure Sn-Cd eutectic as required. Unidirectional solidification was conducted vertically upward using the two-element resistance furnace shown schematically in Fig. 1. With this apparatus, it was possible to obtain a range of growth rates and temperature gradients so that the cell structure could be studied under different growth conditions. Growth rates in the range of 0.4 to 9.1 cm per hr and temperature gradients from 2.25° to 1475°C per cm were used. To ensure steady-state solidification, power to the furnace was stabilized, and the entire apparatus was enclosed in a large box in which the temperature was controlled to within ± 0.2°C. The apparatus was arranged so that the specimen could be quenched in situ during solidification by pouring a large quantity of water down the central vycor tube. Excellent delineation of the solid-liquid interface at the time of the quench was obtained because of the structural changes accompanying the rapid solidification of the remaining liquid. The quenching rate was always extremely rapid as no evidence of a transition in the lamellar spacing at the interface was ever observed. The alloys to be solidified were contained in degassed, high-purity graphite tubes, 1 cm OD and 0.6 cm ID. The specimens were about 18 cm in length. After the alloy had been cast into the tubes, three 0.8-mm holes were drilled in the tube to the center of the specimen. One hole was placed 1 cm from the bottom of the ingot, and the other holes were placed at 8 and 9 cm, respectively, from the base of the ingot. Thirty-four-gage chromel-alumel thermocouples were sealed in the holes. The lower thermocouple was used to position the solid-liquid interface at the start of each experiment,

Jan 1, 1969

By Barbara L. Lakin, Sherman K. Okun

According to a recent market survey, the quality and ability of key personnel, plus past performance on the job, rank high as criteria used by mining companies when selecting a project engineering contractor.

Jan 9, 1977

By H. W. Clark

Electricity must be safeguarded everywhere that it is used. The conditions that exist underground make the use of safeguards more essential there than almost anywhere else. Electric Shock Electric shock is the greatest danger in connection with the use of electricity in mines, because conditions existing underground are so favorable to its occurrence. Men are often obliged to work in more or less uncertain light near bare wires that are carrying dangerous potentials. The fact that the men are standing on the earth practically connects them to one terminal of the electric generator. The moat dangerous piece of electrical equipment underground is the trolley wire. It is necessarily bare and extends for long distances throughout a mine, often less than a man's height from the track rail. Sometimes the making up of trips of cars must be done near low-hanging trolley wires. All 'bare wires offer the same danger that troIley wires do, although not to the same extent. Apparatus that has accidentally come in contact with the ungrounded side of an electric circuit is almost as dangerous as the trolley wire. A severe and even fatal shock may be obtained by coming in contact with the frame of a motor or a switch box that has become charged with electricity, or "alive," as it is usually termed. It is also possible to obtain . shocks from the frames of locomotives and cars if track sanding, poor bonding or a similar cause has put a high resistance to earth in the path of the current. Fires Caused by Electricity The danger from fires caused by electricity arises principally from defective installation and careless upkeep or from injuries to equipment resulting from falls of roof or similar causes. Fires may be started by unrelieved short cifiuits, or grounds, by the blowing of open fuses, and by the overheating of resistances. Incandescent lamps can produce heat enough to ignite combustible materials if the dissipation of the heat from

Jan 1, 1915

By John F. Abel

The following quotation is from "Guidelines for evaluation of undergraduate curricula in geological engineering, mineral processing, and mining engineering" prepared by the Committee on Education of SME of AIME. "The objectives of the Engineers' Council for Professional Development (ECPD), as delineated in its constitution, are: (a) To promote and advance all phases of engineering education with a view to the promotion of the public welfare through the development of the better educated engineer and engineering technician." (Italics added.) The problem is that no one has as yet seriously developed a method of supplying engineering technicians. There were great hopes that the expansion of junior colleges would help satisfy this need. Sadly, they have not; and it appears they are unwilling or unable to supply the need for mineral engineering technologists. Apparently, the junior colleges cannot afford staff for such courses, even when the colleges are located in mining districts.

Jan 1, 1971

By H. Beecher Charmbury

Water is a most remarkable substance. It is essential for life of all kinds. Not only can no one live without water, but man has always needed water for farming, raising animals, manufacturing, transportation, and recreation. When our country was young and inhabited by few people, the streams, rivers, and lakes were able to provide all the clean water needed by man and take away all the wastes created by man. However, with our growing population and our ever-increasing demand for goods and services, the public, industry, and government at all levels have become aware of the need to more efficiently manage the water resources of this nation. Coal has helped this nation to become the greatest industrial nation in the world. Coal has generated our electricity, run our railroads, and helped arm our nation during wartime. The result has been the highest standard of living in the world, a time of widespread prosperity, and a national defense potential that has delivered the hardware during four wars in this century. The use of water in coal mining is somewhat different than in most industries. With the exception of the small amount of water used in cleaning plants and for fire protection, most of the water encountered in coal mining operations is unwanted since it serves no useful purpose. In other words, it must be removed, otherwise it will interfere with mining operations by flooding. In the past, removing water from working areas of most mines was usually a fairly simple matter. Pumps with piping were installed at sumps or low spots in the mine and the water was pumped to the surface. Ditches were often used to drain the water by gravity to the outside or to main sumps for pump discharge. In either case, the water was allowed to flow into the nearest stream or river. The concept of "water is water" was generally accepted without too much concern over what

Jan 1, 1973

CONTENTS PAGE UREN, LESTER C.-Increasing Production of Petroleum by Increasing Diameter of Wells. Discussed by A. Beeby Thompson 1 LAHEE, FREDERIC H.-Comparative Study of Well Logs on the Mexia Type of Structure. Discussed by W. A. I. M. van Waterschoot van -der Gracht.... 4 Increasing Production of Petroleum by Increasing Diameter of Wells Discussion of the paper of LESTER C. UREN, presented at the New York Meeting, February, 1925, and issued, as Paper No. 1364-G, with MINING AND METAL-LURGY, October, 1924. A. BEEBY THOMPSON, London, Eng. (written discussion).-The subject discussed in this paper has long been debated by operators in European fields, where very strong views are held regarding the advisability of controlling gas pressures by shutting in wells. While unwilling to theorize on the subject of restricted flow, the writer has always been disposed to associate himself with those who hesitate to impose any obstruction to a natural transitory state that breaks up the oil-containing strata and establishes a feeder system which no subsequent events, natural or artificial, can approach in intensity. In both Russia and Roumania, where the oil is concentrated in discontinuous, disturbed, and irregular lenticles of sand varying, within short distances, in coarseness of grain, extent of impregnation and degree of cementation, it has been the practice to let the wells run wild in order to provoke disruption of strata. By encouraging violent eruptions, an extended feeder system is created and the ejection of enormous quantities of sand, rock, and clay creates a sump and seepage area that it would be difficult to imitate by any artificial means, not excluding actual mining. Before discussing the somewhat novel method suggested for enlarging the infiltration area, the writer would like to confirm the fact that many valuable data applicable to oil are forthcoming from a study of water phenomena. Long association with water-supply problems in many parts of the world has shown how closely the phenomena of underground movements of water and oil are related, so that it is pleasing to note the author's use of water formulas. But there is one great distinction;

Jan 7, 1925

By J. H. Henderson, L. A. Wilson, R. L. Gergins, R. J. Wygal, D. W. Reed

This paper presents a method of predicting the production history of an underground combustion recovery process. A rigorous solution of the thermodynamics and hydrodynamics involved is beyond the scope of this report. However, a practical scheme to appraise combustion recovery performance has been Worked out. By prudent assumptions, regarding the attainment of steady-state conditions, a trial-and-error solution, which satisfies both material balance and three-phase relative permeability requirements has been evolved and tested. As a combustion zone moves through a formation the interstitial water, the water of combustion and a portion of the oil wil1 be vaporized. These vapors will move downstream to a cooler region of the formation where they will condense. Part of the remaining oil will be displaced by the imposed gas drive and what remains behind will be consumed as fuel. The fluids will distribute themselves downstrean? in a manner which will satisfy the three-phase relative permeability characteristics of the formation. Three distinct zones will exist ahead of the combustion zone: (I) a zone termed a water bank which contains three mobile phases, oil, water and gas; (2) a region containing two mobile phases, oil and gas, called the oil bank; and (3) a zone having the fluid saturution distribution which existed prior to combustion. The mobile water will impose a water flood on the oil in the region containing three flowing phases. The process can be visualized as a simultaneous water .flood and combustion-supported gas drive. It is possible to estimate the saturation distributions in the water bank and oil bank as well as the production history for any combustion temperuture if the porosity, three-phase relative permeability characteristics, oil viscosity and initial saturations are known. This has been done for injection pressures ranging from I to 100 atm, oil viscosities of 10 to 1,000 cp and porosities from 20 to 40 per cent. Several of these calculations have been checked in the laboratory, with the result indicating rather good agreement between the predicted and observed production histories. The analytical and experimental techniques are described and the comparison of predicted and observed performance presented. INTRODUCTION Considerable research by the oil industry during the past 10 years has been directed toward the thermal recovery of crude oil. Of all schemes considered, the one receiving the most attention is in situ combustion. This is a process in which part of the oil is actually burned within the reservoir rock. The uniqueness of the process lies in its potential. Theoretically, this potential generates from the following: (1) it may open the door to vast reserves previously not economically producible, (2) it may induce increased production rates where low rates are now realized and (3) it may give high over-all recovery efficiency. The general idea of the process has received considerable attention in the literature '-' and the following brief description is intended for orientation only. In situ combustion can be visualized by considering a linear system, one end of which represents the injection well and the other the producing well. The formation at the inlet end is raised to ignition temperature by placing a gas or electric heater at the face of the formation or by the ignition of thermite, charcoal or similar material. While heating, the water and part of the oil in the heated region is vaporized and moved out into the reservoir by the injection of gas containing oxygen. In addition, part of the oil is displaced as liquid by the imposed gas drive. The oil not displaced is modified to an immobile, coke-like material (hereafter referred to as coke) by the high temperatures existing immediately ahead of the combustion zone. This coke is used as fuel, and the combustion front advances through the formation at a temperature which is probably in excess of 800°F. As the combustion front advancek it will drive ahead all interstitial oil not rendered immobile and all interstitial water plus the water formed by the combustion of hydrogen. As a result the sand behind the combustion zone is freed of all oil and water. Although the general description of the process has been outlined in the literature, there has been no consideration of the behavior of the fluids moving downstream from the combustion front. It is the purpose of this paper to present a technique

By Earl Kennedy

The Northern West Virginia Region of Consolidation Coal Company consists of ten underground mines. The Pittsburgh seam of coal is being mined. This seam is approximately seven feet in thickness in our area. The mining equipment consists of twelve longwall systems and a combination of Joy and Jeffrey ripper type miners. There are a few boring type machines still in use, but these are rapidly being phased out. The auxiliary ventilation fans being utilized vary in type from single stage carriage mounted 20 horse-power Joys to 40 and 50 horsepower two-stage Joys, Buffalo Forge, and Peabody brands. The particular fans that we have primarily been working with on noise reduction are the two-stage 40 and 50 horsepower types.

Jan 1, 1982

Important chemical and other technical engineering work necessary, for the prosecution of this war is being carried on by the Bureau of Mines Experiment Station, at Washington, D. C. The services of trained men of the following classifications are urgently needed Bacteriologists Instrument makers Biologists Laboratory Assistants Chemists, Inorganic Laborers Chemists, Organic Machinists Chemists, Physical Physiologists Chemists, Electro- Plumbers Chemical Engineers Steamfitters Draftsmen Stenographers. Electrical Engineers Skilled labor of various kinds If your training fits you for any of these occupations, send to the Bureau of Mines, American University Experiment Station, . Washington, D. C. for blank forms. When properly executed and returned by you, these forms will be placed on file, and when a vacancy occurs you will be considered for it and will be notified if your services are desired. If you are a registrant in the draft, and have not yet been- ordered to camp, it may be possible to have you immediately inducted into the service for work here. If you are not in the draft, but feel that you wish to serve your country in the present crisis, you can enlist, or serve as a civilian. Serve your country where you can serve it best. VAN H. MANNING, Director.

Jan 6, 1918

PICK AND SHOVEL CLUB, CASE SCHOOL OF APPLIED SCIENCE The last meeting of the year of the Pick and Shovel Club of Case School of Applied Science was held on May 20, 1919. The speaker, Dr. Zay Jeffries, gave a very instructive and interesting talk on the Metallography of Non-ferrous Metals. The club has had a very successful year in spite of the loss of a few months time through the S. A. T. C. Among the speakers for the year were Dr. F. R. Van Horn, Dr. C. H. Fulton, and Dr. W. R. Veazey of our school; Dr. E. S. Moore of Penn. State College; Dr. Ansel St. John, of the National Carbon Co.; and Mr. V. S. Bidle, of the W. S. Bidle Co. The graduating members wish the club the best of success for the coming year. BERTRAND R. WARMELING, Secretary.

Jan 7, 1919

By R. A. Haney, S. J. Gigliotti

Over the past ten years, analysis of the acceptability of face ventilation systems has been based on numerical criteria rather than solely a study of air flow and methane patterns in the face area. This type of analysis has become possible primarily because of the instrumentation and mathematical models developed by the Ventilation Division, Pittsburgh Health Technology Center, Mine Safety and Health Administration (MSHA). To properly use these mathematical models, large amounts of methane and airflow data must be collected in the face area during mining activities. To supplement underground testing of face ventilation systems, a full scale model of a face area was built. This model includes a full scale model continuous miner, a face ventilation system, a gas release system, and a remote methane detection system. The remote methane detection system consists of an array of twelve methane sensors located throughout the face area. Data from the sensors are transmitted to strip chart recorders. Methane, air quantity, and other data collected during a test are entered into a computer for analysis. This paper presents the data entry system, the models used for data analysis, the test results, and the application of these results to a face ventilation system.

Jan 1, 1983

By C. A. Zapffe

BOTH the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. BLEEDING, RISING, AND PIPING The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinction between bleeding and rising in reference to killed metal.* POROSITY Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth1 noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel-oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1942

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935