Search Documents

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furbish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 10, 1913

The Library of the above-named Societies is open from 9 A.M. to 9 P.M. on all week-clays, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references' and copies of articles on-mining and metallurgical subjects; to determine the existence of mining-maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining-reports, maps privately issued, and similar material, which will be classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and assurance is given that most careful service will be rendered to them.

Jan 7, 1913

By F. W. McNair

WITHIN the last twenty-five or thirty years the actual operations of the great mining industry have passed almost wholly under the charge of men trained in the technical colleges. It follows that the industry is profoundly influenced for good or ill by the character of the training which the college graduate receives, and the relations existing between the industry and the colleges. This fact seems to be generally recognized, as evidenced, for example, by the existence of a Committee on Technical Education created some two or three years ago by the Mining and Metallurgical Society of America. In 1921 this committee rendered a very able and. extremely well poised reports of technical education as applied to the prospective mining engineer. It deserves the attention of every one interested in the effectiveness of engineering training. That the importance of the relation between the mining industry and the engineering colleges is recog-nized is evidenced also by the mass of criticism, usually adverse, which is proffered to and often hurled at the colleges by those in the industry. The man inn the field sometimes goes so far as to say that engineering educa-tion is hopelessly inefficient and its product worthless, while the college worker sometimes complains that the demands of the industrialist are too numerous and conflicting to be met, and adds that they would' best be ignored. Between these extremes, there seems to be a general consensus of opinion that the training of the would-be engineer can be, and. ought to be, made much better than it now is.

Jan 4, 1923

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By C. A. Heiland

The new geophone described herein was developed by Charles H. Hull, instrumentmaker of the Colorado School of Mines, and the writer. The first geophone was invented during the war for the purpose of detecting enemy sapping or underground mining operations and for locating enemy artillery. It is based on the principle of the seismograph—a heavy lead mass suspended by one or two diaphragms, which are clamped to an air-tight case. When the ground vibrates during the transmission of sound waves, the case moves with it while the so-called steady mass remains practically motionless. Attached to the top of the casing is a hose leading to an earpiece shaped like a stethoscope. When the mass and the diaphragm move up and down in the case, the air is compressed and rarified in the inside; thus the vibration is communicated as sound wave to the human ear. The geophone combines a surprising simplicity of construction with an extreme sensitivity. Other listening instruments were developed during the war, adaptations of the telephone and the microphone—that is, instruments operating through the medium of electricity—of which the so-called seismicrophone, an adaptation of the carbon-granule microphone receiver, probably has found the greatest application, but such instruments apparently have not proved as useful as the simple geophone despite obvious advantages arising from the use of electricity. The carbon receivers were more subject to extraneous noises and to what is called "frying," and they did not offer the advantage possessed by the geophone; namely, the simultaneous use of two receivers, which makes it possible to determine the location of the source of sound. During the war, the U. S. Bureau of Mines made a study of the geophone and of the propagation of sound waves through rock. These studies have been continued, as the earlier results proved the possibility of using the geophone in various non-military ways, principally in mining, and the results of these studies have been published.'

Jan 1, 1932

By J. R. Jargon, H. K. van Poollen

Non-Newtonian fluids may be injected into a reservoir during secondary recovery operations. The non-Newtonian fluid used in this work is a power-law type of fluid that is, the viscosity of the fluid decreases as the flow rate or rate of shear increases. This paper presents equations for steady-state linear and radial flow of such fluids, transient behavior results from a finite difference model of a radial system, and transient behavior results from a field test. The equations that describe the flow of a non-Newtonian fluid are non-linear and are solved numerically. Finite difference solutions are presented as curves of dimensionless pressure drop at the wellbore us dimensionless time for a constant injection rate. Solutions were obtained for 5-percent, 10-percent and 100-percent PV of a non-Newtonian fluid for injection rates of 1, 10, 100 and 1000 cc/sec and for a 5 percent PV of non-Newtonian fluid located at T = Tw' 3, 10, 20, 50 and 100 ft for a flow rate of 1 cc/sec. The buildup curves do not exhibit a stmight-line portion as is the case for Newtonian flow through porous media. Correlations also are shown for the productivity index vs rate for the computer model study and the field tests. INTRODUCTION During various secondary recovery operations non-Newtonian fluids are injected. Such fluids, in general, include thickened water and gelled fluids. The term "non-Newtonian" implies that the viscosity is not only dependent upon temperature and pressure, but also on the rate of shear that is applied to the fluid. For example, water, which is a Newtonian fluid, will have essentially the same viscosity no matter what rate of shear is applied. A pseudo-plastic fluid exhibits a decreasing viscosity when higher rates of shear are applied; a dilated fluid has an increasing viscosity with increasing rates of shear. The objective of studies performed and described in this report is to obtain relationships and mathematical and empirical descriptions of the flow of non-Newtonian fluids through porous media. Simple mathematical relationships, computer studies that include the unsteady-state behavior of such fluids, and field tests are used. PREVIOUS LABORATORY STUDIES Laboratory studies have been performed by several investigators. The fluids used in one investigationl were surfactant-stabilized dispersions of water in hydrocarbons. Its Fig. 6 is reproduced as our Fig. 1. This effective-viscosity vs frontal-velocity diagram shows that this fluid is of the power-law type over a fairly large range of frontal velocities. Gogartyl developed an equation for the effective viscosity as a function of shear rate that reduces to Eq. 2 for frontal velocities greater than about 2 ft/D. The fluid characteristics used in the present study are similar to those reported by Gogarty. Christopher and Middleman2 performed experiments with power-law fluids flowing through pipes packed with glass beads. They used a modified Blake-Koteny

Jan 1, 1970

By Joseph L. Gillson

Bentonite, designating a distinct type of clay, is a young name in mineral nomenclature in the light of the age-old names of most other useful nonmetallics. The earliest references in literature are to "soap clay" (1873) "taylorite" (1888) and finally "bentonite" in 1897, from its occurrence in the Fort Benton series of rocks near Rock Creek, Albany County, Wyoming. Bentonite is a rock term and consists largely of montmorillonite clay. The latter name was proposed in 1847 for a plastic clay found at Montmorillon, France. A clay of apparently identical properties was described by Cronstedt of Sweden in 1788 and a number of other similar clays found in France were given other names in publications from 1853 to 1856. The mineral name montmorillonite was recognized by Dana in 1892. The recognition of "clay mineral" distinctions which led to the present-day classifications of clays by their chief mineral content, dawned in the early part of the twentieth century. Grim6 has aptly said: About 1924, Ross10 and some colleagues of the U. S. Geological Survey began a study of the mineral composition of clays that led to a series of monumental papers on the subject. By the early 1930's what has come to be known as the clay-mineral concept became firmly established in the minds of a great many people actively studying clay materials. The clay mineral concept designates the major clays as kaolins, montmorillonites and illites and by this concept bentonites are now defined as "fine-grained clays containing not less than 85 pct montmorillonite" and a wide variety of clays found all over the world are included in that classification. They could all properly be called "montmorillonite clays" but the common commercial name is bentonite. For a period of over forty years from the time of the earlier discoveries, bentonite was thought to be only the sodium type highswelling clay produced principally in Wyoming. By the clay mineral concept, non-swelling montmorillonite clays also became known as bentonite. In the trade there are two broad divisions-sodium bentonite, often called Wyoming or "western," which expands in water and carries sodium as its predominant exchangeable ion, and calcium bentonite often called "southern," which has negligible swelling and carries calcium as its principal exchangeable ion. There are many intermediate gradations. Properties The mineralogy and chemistry of the clays are so complex that the subject cannot be summarized briefly. The reader is referred to Chapter 12 of this volume in which the subject is treated at some length. Grim6 gave the formula for montmorillonite as (OH)4Si8AL4020.nH2O. He wrote: Montmorillonite is composed of units made up of two silica tetrahedral sheets with a central alumina octahedral sheet. . . . Exchangeable rations occur between the silicate layers. . . . The words "tetrahedral" and "octahedral" refer to the coordination number of the cations in the unit cell in the crystallographic lattice. Carroll5a stated: That the montmorillonite structure is the same as that of mica, but the layers are not held together by K+ ions; and water and other polar molecules, such as organic molecules, can enter between the unit layers and cause expansion. Ex-

Jan 1, 1960

By Earl Hunner

IT is common knowledge that the iron orebodies of the Mesabi range lie nearly horizontal and are of trough or blanket-like types. These orebodies are from a few feet to several hundred feet thick and vary from a few acres in extent to the size of the largest one, at Hibbing, Minn., which is over 1 mile wide and 3 miles long. They are covered with sand, boulder and clay overburden and occasionally, shallow depths of ledge material, varying in total depth from about 20 to 200 ft. Large areas are not capped with overlying ledge material; the top of the ore lies directly underneath the surface material. Because of the comparatively great tonnage of ore, open-pit mining has made tremendous strides since the first open-pit ore was shipped from this range by the Merritt brothers, from the Mountain iron mine in October, 1892, and along with the great development of open-pit mining on the Mesabi range has gone a tremendous change in the character of equipment used.

Jan 1, 1930

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled 'Steel Mine Timbers.' " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By F. J. Haller

IN 1943, we found, in the new Mather operation, a very unusual and disappointing condition in the footwall rock where all of our main haulageways were to be located. With the exception of a few hundred feet out of the thousands then planned and since driven, all of the openings require support. In general, the ground is not particularly heavy, at least by our standards, but it must be supported and the back carefully covered. Also, our operations require rather wide plat openings (16 to 18 ft) and rather flat curves at the turn-outs, all of which adds to the problem. When this completely unforeseen condition was discovered, ordinary timbering was the only answer, because of the impossibility of obtaining adequate steel supplies in time due to war shortages. Then by the time steel supplies were obtained and a practice developed, we found ourselves with between four and five miles of main haulage drifts and plat openings of a permanent nature, all of which were supported by hardwood timber, some of which had already rotted to an unsafe degree. Also, our drifting program was adding some two miles per year to the above figure. F. J. HALLER, Member AIME, is Superintendent, Mather Mine, Cleveland-Cliffs Iron Co., Ishpeming, Mich. AIME Columbus Meeting, September 1949. TP 2840 A. Discussion (2 copies) may be sent to Transactions AIME before May 31, 1950. Manuscript received Aug. 22, 1949. Revision received Jan. 17, 1950. To give all of the details of our experiments, studies, and experiences would fill a large book, but we were satisfied that our organization had done an excellent job, starting from scratch. You can appreciate our surprise when we discovered that we had added very little to an existing record. Attention was called to a footnote in a copy of "Carnegie Pocket Companion" year 1923. The note read: "Full information as to uses of H-Beams is given in pamphlet entitled 'Steel Mine Timbers.' " A search of our Engineering Library brought to light a pamphlet printed in 1911 showing extensive use of steel for this purpose. Except for welding in place of riveting, we have added very little to the designs in that book. We have, however, developed an experience which proves, at least to our own satisfaction, that steel mine supports pay off under the proper conditions. We are now convinced, in spite of the relatively high initial cost of materials, that steel sets, because of comparatively low installation cost, are actually cheaper than either treated or untreated wood sets, if they are properly designed and adapted. Several Sections in Use: Convenience guided our first experiments in steel sets, since for a number of years, we had used the 4-in. WF, 10 lb per ft section in 10-ft lengths as safety forepoles along with wood forepoles. This section replaced the 40-lb rail which had formerly been used for the purpose. Having the 4-in. WF sections on hand, it was natural that our first experiments in steel sets involved their use. Later, the rolling of the 10-lb section was discontinued in favor of the much stronger 13-lb section, which is now standard for both legs and caps in areas of no particular weight, but which, none the less, require permanent support. Our experiments involved the use of the 10- and 13-lb sections as legs and 6- and 8-in. I beams, 16 and 23 lb per ft, respectively, as caps. Experience soon indicated that, if the ground were heavy enough, and the opening wide enough to require a cap stronger than 13-lb, the 8-in, 23-lb should be used, eliminating the 6-in. I beam. We now know that the 8-in. WF section of the same weight, which we propose to use in the future, is considerably stronger for the amount of money involved. Comparative Strengths: Tables I to IV giving strengths of several species of timbers as compared with the structural sections that we now use have been prepared in accordance with accepted practice. Experience indicates that failure due to compression perpendicular to the grain of the wood does not destroy the effectiveness of a wood set frequently enough to be a practical factor. Therefore, no table of these values is included.

Jan 1, 1951

By George Collins

AT the meeting of the Western Division of the American Mining Congress, held in Denver last September, papers were read by F. H. Brownell, a vice-president of the American Smelting and Refining Co. and chairman of its finance committee, and by H. Foster Bain, former director of the United States Bureau of Mines and now secretary of the A. I. M. E.. which dealt thoroughly with certain phases of my sub-ject. These addresses can hardly have failed to awaken serious reflection in all who listened to them; but their implications have apparently not penetrated the con-sciousness of bankers, economists and statesmen, whose business it is, or should be, to prepare for the economic and social changes which must inevitably follow, if the conclusions which I shall outline hereinafter are true. In discussing this subject I wish to disclaim any intention or desire to forecast the course of the metal markets or the immediate prospects of the mining in-dustry. The facts' adduced must inevitably influence the value of metals, the activity and profitableness of mining, and perhaps also the social status of those en-gaged in it. But my forecasts do not refer to this year, next, year, or the year after. The nearest ap-proach to a date on which I will venture is that the relative scarcity of gold may begin to make itself felt in something like ten years from now, but its effect will not culminate for several years thereafter. Scarcity of new gold is likely to be offset, to some extent, by increasing use of currencies based on credit; but unless it is found possible to dispense with the gold standard altogether, this can hardly prevent a great ultimate fall in commodity prices. This fall, moreover, is likely to be more severe in manufactured goods than in what are, popularly termed raw ma-terials; and most of all in those manufactured goods which are susceptible to the greatest degree to cheapen-ing by mass production, and which are least counter-affected by increasing metal prices; by which I mean those in which the cost of metal contained forms a relatively small, element in the total cost of production.

Jan 6, 1927

By William M. Newton, John E. Sherborne

The value of the electric log as a means of interpreting underground structures has been increasingly demonstrated by its almost universal present-day use. It becomes important, therefore, to be able to evaluate the factors that affect the values obtained. By far the greatest number of electric logs are measured today in boreholes filled with rotary mud, the properties of which may exert an important influence on the electric log. In an effort to establish what the order of magnitude of such effects might be, a series of investigations was made in the laboratory and the field. Apparatus suitable for either field or laboratory use was designed and a procedure established for determining the factors that affect the resistivity of drilling muds over a wide variation in mud condition. Five muds representative of the types of clay-base muds employed in California were tested and the following observations were made: 1. The effect of raising the temperature from 8o° to i8o°F. is to decrease the resistivit~ of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity. The results of the investigation indicate that the mud resistivity is materially affected by the addition of electrolytes whether these are added for the purpose of conditioning the mud or enter the mud when salt beds or highly saline structures are penetrated. It should be observed, however, that the magnitude of the effect produced upon the electric log by changes in mud resistivity is also dependent upon the relative salinity of the water en. countered in the formation being logged. The laboratory data are supplemented by field data, which indicate that both the self-potential and resistivity curves are influenced by mud resistivity.

Jan 1, 1946

By John E. Sherborne, William M. Newton

The value of the electric log as a means of interpreting underground structures has been increasingly demonstrated by its almost universal present-day use. It becomes important, therefore, to be able to evaluate the factors that affect the values obtained. By far the greatest number of electric logs are measured today in boreholes filled with rotary mud, the properties of which may exert an important influence on the electric log. In an effort to establish what the order of magnitude of such effects might be, a series of investigations was made in the laboratory and the field. Apparatus suitable for either field or laboratory use was designed and a procedure established for determining the factors that affect the resistivity of drilling muds over a wide variation in mud condition. Five muds representative of the types of clay-base muds employed in California were tested and the following observations were made: 1. The effect of raising the temperature from 8o° to i8o°F. is to decrease the resistivit~ of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3. The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as baroid and limestone, tend to increase the resistivity of drilling mud. 6. Cement and counteracting reagents reduce mud resistivity. The results of the investigation indicate that the mud resistivity is materially affected by the addition of electrolytes whether these are added for the purpose of conditioning the mud or enter the mud when salt beds or highly saline structures are penetrated. It should be observed, however, that the magnitude of the effect produced upon the electric log by changes in mud resistivity is also dependent upon the relative salinity of the water en. countered in the formation being logged. The laboratory data are supplemented by field data, which indicate that both the self-potential and resistivity curves are influenced by mud resistivity.

Jan 1, 1946

By J. D. Hanawalt, C. E. Nelson, J. A. Peloubet

THE subject of the salt-water corrosion resistance of magnesium alloys is somewhat like that of the pitting of stainless steels, in that it involves a relatively small percentage of the applications but receives a much greater proportion of the publicity. Actually magnesium alloys are in use in many exterior applications as well as interior, with no trouble from corrosion. Magnesium and its alloys have a striking stability against atmospheric attack, being far superior to iron. Specimens exposed unprotected to atmospheric weathering for 10 years show only a superficial surface-film formation. The basic nature of magnesium and of its important alloys is that they are also resistant to the attack of salt water even in an unprotected state, giving substantially no loss in weight after one year of alternate immersion in 3 per cent NaCl solution (Fig. I). This basic behavior is often masked because of the extreme sensitivity of these alloys to certain impurities and combinations of impurities. It is known, and the subject of increasing emphasis, that higher purity leads generally to greater stability for many materials, nonmetallic as well as metallic. However, a review of the literature on the corrosion factors in magnesium alloys shows that almost all researchers worked with base metal in which metallic impurities varied in uncontrolled amounts. The major factor, that of metallic impurities, probably greatly overshadowed the effects of minor ones such as flux inclusions, nonmetallic impurities, porosity, metallographic state, which these researchers presumed to study. In the present investigation the first observation of interest is that whereas magnesium of commercial purity (99.9 per cent pure) has a corrosion rate in alternate immersion in 3 per cent NaCl solution at room temperature of anywhere from 5 to 100 mg. per sq. cm. per day, the corrosion rate of high-purity magnesium is 0.15 ± 0.05 mg. per sq. cm. per day. The principle followed in the experiments was to add to such base magnesium other elements, singly and in combination, in controlled and known amounts and to observe the corrosion behavior of the resulting alloy. These experiments show the existence of what may be called "tolerance limits" of magnesium and some of its alloys for certain impurities. The extremely small percentages of impurities involved and the sharpness of the corrosion discontinuities appear to be quite unpredictable. In order to carry on this work, it was necessary to develop an analysis technique suitable to the problem. In some cases it was necessary quantitatively to analyze impurities to less than 0.001 per cent. The experimental data to be presented are based on observation of about 5000 alloy specimens and on more than 50,000 quantitative analyses. While the primary purpose of this paper is to present the experimentally obtained data on corrosion rates as a function of composition, and particularly to demon-

Jan 1, 1941

By Theo W. Robinson

The evolution of the modern blast-furnace from the embryonic stages of comparatively few years ago, has been the work of wide praetiee and experiment. That much is still to be desired, the experience of every furnace-manager mill testify. Mr. Walsh's paper on "The Irregularities of the Blast-Furnace Process, and a Practical Way to Avoid Them" (Trans., xv., 419), proposes a new solution of the problem of interior lines, and one that has given rise to not a little speculation and controversy. The investigation described in this paper was undertaken to test experimentally the theory of Mr. Walsh as to maximum reducing capacity. Briefly explained, Mr. Walsh's views (outside of his claim for increased efficiency due to having the bosh wholly within the meltingzone) are, that a furnace of contracted stack and throat, on his lines. may equal in product one of considerably greater cubical capacity. The explanation offered for the theoretical greater capacity per cubic foot of his furnace is, that the increased tension of gases caused by passing through the small area mill promote transpiration, thus facilitating reduction and permitting more rapid driving. This alleged relation will appear from a hypothetical case in which a furnace, A, constructed on Mr. Walsh's lines, has but 1/x of the cubical contents of a furnace, B, of modern type; the two being equal in height. In order that A shall have the same capacity as B, both working normally with the same mixture and burden, and

Jan 1, 1889

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.' Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By Hugh Rose

THE properties of the company lie within the Pachuca district, State of Hidalgo, Mexico, connected by three railway lines with Mexico City, 55 miles southwest, and by two lines with Vera Cruz, 250 miles southeast. The ores were formerly divided by sorting into two classes, smelting and milling, the former averaging about 2 oz. gold and 335 oz. silver, the latter 0.12 oz. gold and 23 oz. silver. The smelting ores were sold to custom plants, principally the American Smelting & Refining. Co. at Aguascalientes. The milling ores were treated by the patio process at the Guadalupe Hacienda, at Pachuca. This patio was probably the largest in existence at the time and continued in active operation up to March, 1910. In January, 1910, the mines and patio were sold to English interests, represented by Camp Bird Limited. Two new companies were formed, the Compañia de Santa Gertrudis, S. A., to operate the mines, and the Compañia Beneficiadora de Pachuca, S. A., to build and operate a custom cyanide milling plant. (Fig. 1.) GEOLOGY The historical geology of the Pachuca district is described by Fred J. Pope as follows: 1. The most recent sedimentary rocks in the district belong to the Cretaceous period. 2. The Cretaceous rocks were penetrated by large intrusions of ande-site (referred to hereafter as primary andesite) which occur as elliptical dome-shaped masses, striking northwest-southeast. These andesite bodies are from 8 to 15 miles long and from 6 to 10 miles wide. 3. A period of erosion during which the contour of the andesite domes was changed. 4. Andesite flows (secondary andesite) which rest unconformably on the primary andesites.

Jan 8, 1916

By Hugh Rose

The properties of the company lie within the Pachuca district, State of Hidalgo, Mexico, connected by three railway lines with Mexico City, 55 miles southwest, and by two lines with Vera Cruz, 250 miles southeast. The ores were formerly divided by sorting into two classes, smelting and milling, the former averaging about 2 oz. gold and 335 oz. silver, the latter 0.12 oz. gold and 23 oz. silver. The smelting ores were sold to custom plants, principally the American Smelting & Refining Co. at Aguascalientes. The milling ores were treated by the patio process at the Guadalupe Hacienda, at Pachuca. This patio was probably the largest in existence at the time and continued in active operation up to March, 1910. In January, 1910, the mines and patio were sold to English interests, represented by Camp Bird Limited. Two new companies were formed, the Compania de Santa Gertrudis, S. A., to operate the mines, and the Compania Beneficiadora de Pachuca, S. A., to build and operate a custom cyanide milling plant. (Pig. 1.) Geology The historical geology of the Pachuca district is described by Fred J. Pope as follows: 1. The most recent sedimentary rooks in the district belong to the Cretaceous period. 2. The Cretaceous rocks were penetrated by large intrusions of ande-site (referred to hereafter as primary andesite) which occur as elliptical dome-shaped masses, striking northwest-southeast. These andesite bodies are from 8 to 15 miles long and from 6 to 10 miles wide. 3. A period of erosion during which the contour of the andesite domes was changed. 4. Andesite flows (secondary andesite) which rest unconformably on the primary andesites.

Jan 1, 1917

By A. H. Kline, E. B. Zimmer, Zay Jeffries

It is well known that many properties of a given metal vary with the size of grain or cell. For most industrial purposes, where high ultimate strength and high elastic limit are desired, the manufacturer tries to produce a fine-grained structure. For some purposes, for example in transformer iron, a coarse-grained structure is desirable. The terms fine-grained and coarse-grained are used only in a relative sense. For example, a fine-grained cast copper might have grains 100 times larger than coarse-grained high-speed steel. Similarly, a finegrained steel rail might have grains or cells 100 times larger than coarsegrained wire, which was made of steel from the same heat. In some metals, the change in grain size is more appreciable khan the changes in any of the properties determined by the tensile test. Furthermore, in metals which have been annealed or subjected to high temperatures, grain size may prove to be a better indication of the life of the metal in use than the tensile test. One of the authors was able to supplant the tensile test with grain-size determinations in the control of metal for a specific use, the latter determination being more indicative of the life of the metal part than the tensile test. A grain-size determination with a tensile stest is, of course, more valuable than either singly. At present there is a decided dearth of data on actual grain-size determinations in metals, and consequently a corresponding lack of ability to interpret the determinations after they are made. It would be desirable to have correlation made between grain size and properties of metals, comparing thousands of determinations. In this way, grain-size determinations might be interpreted in much the same manner that tensile tests are now. Several Methods of Measuring Grain Size One of the chief reasons why more grain-size measurements have not been made is the excessive work involved in making a determination.

Jan 1, 1916

By H. R. Shidel

THIS paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. S. Bureau of Mines; Magnolia Petroleum Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," S. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon. (2) That the only striking connection between structure and water is in the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by fine-grained, well cemented sand, which is barren. Possibly two, or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 10, 1918